Bob invested $2,879 in the mutual fund in 2015 and the rate of return on Mary's investment is 34.33%.
During the last four years, a certain mutual fund had the following rates of return: At the beginning of 2014, Alice invested $2,943 in this fund. At the beginning of 2015, Bob decided to invest some money in this fund as well. How much did Bob invest in 2015 if, at the end of 2017.
Alice has 20% more than Bob in the fund? Round your answer to the nearest dollar.The table below shows the rates of return for the mutual fund:YearRate of return (%)20142.520155.520166.720177.6.
To solve the problem, we can use the future value formula:FV = PV(1 + r)^n,
where:FV is the future valuePV is the present valuer is the annual rate of return (expressed as a decimal)n is the number of years.
We can apply this formula to Alice's investment of $2,943 and Bob's investment to find the ratio of their investments at the end of 2017.Alice's investment:PV = $2,943r = 7.6% (from the table above)n = 4 (since the investment was made at the beginning of 2014 and we want to find the value at the end of 2017)FV_A
$2,943(1 + 0.076)^4 ≈ $3,882.20
Bob's investment:
Let x be the amount Bob invested at the beginning of 2015.PV = xr = 5.5% (from the table above)n = 2 (since the investment was made at the beginning of 2015 and we want to find the value at the end of 2017).
FV_B = x(1 + 0.055)² ≈ 1.1221x.
We know that Alice has 20% more than Bob in the fund, so: FV_A = 1.2FV_B.
We can substitute the expressions for FV_A and FV_B in this equation and solve for x:
3,882.20 = 1.2(1.1221x)3,882.20
1.34652x2,879.33 ≈ x.
Therefore, Bob invested about $2,879 in the mutual fund in 2015.Question 2:5 years ago Mary purchased shares in a certain mutual fund at Net Asset Value (NAV) of $66.
She reinvested her dividends into the fund, and today she has 7.2% more shares than when she started. If the fund's NAV has increased by 25.1% since her purchase, compute the rate of return on her investment if she sells her shares today. Round your answer to the nearest tenth of a percent.
Let's begin by calculating how many shares Mary has now. We know that she has 7.2% more shares than when she started. So, if she had x shares five years ago, now she has:1.072x shares.
Now, we want to calculate the NAV of Mary's shares today. Since the NAV has increased by 25.1%, today's NAV is:
1.251 × $66 = $82.665.
Now we can calculate the value of Mary's investment today as follows:Value
1.072x × $82.665 = $88.63498x.
Now, Mary's initial investment was x × $66 = $66x.
Therefore, the rate of return on her investment is:RR = (Value - Initial Investment) / Initial Investment= ($88.63498x - $66x) / $66x= $22.63498x / $66x= 0.3433... = 34.33% (rounded to the nearest tenth of a percent).
Therefore, Bob invested $2,879 in the mutual fund in 2015 and the rate of return on Mary's investment is 34.33%.
To know more future value formula visit;
brainly.com/question/30302091
#SPJ11
4. The gusset plate is subjected to the forces of three members. Determine angle 0 for equilibrium. The forces are concurrent at point O. Take D as 10 kN, and Fas 8 kN 7 MARKS y DKN А B OOO X С T
The angle θ for equilibrium is approximately 53.13 degrees.
What is the angle θ for equilibrium when the gusset plate is subjected to concurrent forces from three members?To determine the angle θ for equilibrium, we need to make some assumptions about the missing values and the geometry of the system. Let's assume the following:
Assume Force X is acting vertically upwards.
Assume Force T is acting at an angle of 45 degrees with the horizontal axis.
With these assumptions, we can proceed to solve for the angle θ. Let's label the angles as follows:
Angle between Force D and the horizontal axis = α
Angle between Force F and the horizontal axis = β
Angle between Force T and the horizontal axis = 45 degrees
Angle between Force X and the horizontal axis = 90 degrees
Now, we can write the equations for equilibrium in the x and y directions:
Equilibrium in the x-direction:
T * cos(45°) - X = 0
Equilibrium in the y-direction:
T * sin(45°) + X + D - F = 0
Substituting the known values:
T * (√2/2) - X = 0
T * (√2/2) + X + 10 - 8 = 0
Simplifying the equations:
(√2/2)T - X = 0
(√2/2)T + X + 2 = 0
Adding the two equations together, the X term cancels out:
(√2/2)T + (√2/2)T + 2 = 0
√2T + √2T + 2 = 0
2√2T = -2
T = -1/√2
Now we can solve for θ:
T * cos(θ) = X
(-1/√2) * cos(θ) = X
Substituting the assumed value for X (vertical upward force):
(-1/√2) * cos(θ) = 0
cos(θ) = 0
The angle θ for which cos(θ) = 0 is 90 degrees. Therefore, assuming the missing values and the given assumptions, the angle θ for equilibrium is 90 degrees.
Learn more about angle θ for equilibrium
brainly.com/question/5941152
#SPJ11
Water is flowing at a rate of 0.119 m^3/s at a pipe having a diameter of 0.169 m, a length of 57 m and with a friction factor f of 0.006. What is the flow at the parallel pipe having a diameter of 0.08 m and a Hazen Williams C coefficient of 130 and a length of 135 m. Express your answer with 4 decimal places
The flow rate in a parallel pipe is approximately 0.0223 m³/s, calculated using the Hazen Williams formula. The head loss is determined using the formula H = f(L/D) * V²/2g.
Given the following details:
Water is flowing at a rate of 0.119 m³/s
Diameter of the pipe = 0.169 m
Length of the pipe = 57 m
Friction factor = 0.006
Diameter of the parallel pipe = 0.08 m
Hazen Williams C coefficient = 130
Length of the parallel pipe = 135 m
To determine the flow at the parallel pipe, we can use the following formula:
Hazen Williams formula :
Q = 0.442 C d^{2.63} S^{0.54}
Where:
Q = flow rate (m³/s)
C = Hazen-Williams coefficient
d = diameter of pipe (m)S = head loss (m/m)
Let’s first determine the head loss S for the given pipe:
The head loss formula is given by:
H = f(L/D) * V²/2g
Where:
H = Head loss (m)
L = Length of the pipe (m)
D = Diameter of the pipe (m)
f = friction factor
V = velocity of fluid (m/s)
g = acceleration due to gravity = 9.81 m/s²
Given the diameter of the pipe = 0.169 m, length = 57 m, flow rate = 0.119 m³/s, and friction factor = 0.006.
Substituting the values in the above equation, we get:
H = 0.006(57/0.169) * (0.119/π(0.169/2)²)²/2*9.81
= 0.821 m/m
Now we can calculate the flow rate in the parallel pipe as follows:
Q₁ = 0.442 * 130 * (0.08)².⁶³ * (135/0.821).⁵⁴
= 0.0223 m³/s
Hence, the flow rate in the parallel pipe is 0.0223 m³/s (approx.)Therefore, the answer is 0.0223.
To know more about Hazen Williams formula Visit:
https://brainly.com/question/33366984
#SPJ11
7.13 Students in the materials lab mixed concrete with the
following ingredients;
9.7 kg of cement, 18.1 kg of sand, 28.2 kg of gravel, and 6.5
kg of water. The
sand has a moisture content of 3.1% and
The weight of sand with no moisture content in the concrete mix is 17.5389 kg.
The weight of sand with no moisture content in the concrete mix can be calculated as follows:
Weight of sand = Total weight of concrete mix - weight of cement - weight of gravel - weight of water
= 9.7 + 18.1 + 28.2 + 6.5
= 62.5 kg
The weight of moisture in the sand can be calculated as follows:
Weight of moisture = Moisture content of sand × Weight of sand
= 3.1/100 × 18.1
= 0.5611 kg
The weight of sand with no moisture content in the concrete mix can be calculated as follows:
Weight of sand with no moisture content = Weight of sand - Weight of moisture
= 18.1 - 0.5611
= 17.5389 kg
Therefore, the weight of sand with no moisture content in the concrete mix is 17.5389 kg.
Know more about the moisture content
https://brainly.com/question/27276832
#SPJ11
transportion Eng
[30 Marks] Q1: The traffic on the design lane of a proposed four-lane rural interstate highway consists of 6% trucks. If classification studies have shown that the truck factor can be taken as 0.75 ES
The traffic volume in one direction for the design lane of the proposed highway is 1 lane.Answer: 1 lane
The traffic on the design lane of a proposed four-lane rural interstate highway consists of 6% trucks, and the truck factor can be taken as 0.75.We need to determine the traffic volume in one direction for the design lane of the proposed highway.
Let the average daily traffic volume in one direction be ADT
Then, the number of trucks in one direction = 6% of ADT
And, the number of passenger cars in one direction
= (100 - 6)%
= 94% of ADT
∴ Number of Trucks = 0.06 ADT
Number of Passenger cars = 0.94 ADT
The equivalent standard axles of trucks = 0.75 ES
∴ Equivalent Standard Axles of Trucks = 0.75 × 0.06 ADT
Equivalent Standard Axles of Passenger cars = 0.05 ES
∴ Equivalent Standard Axles of Passenger cars = 0.05 × 0.94 ADT
Total equivalent standard axles = Equivalent Standard Axles of Trucks + Equivalent Standard Axles of Passenger cars
∴ Total equivalent standard axles = 0.75 × 0.06 ADT + 0.05 × 0.94 ADT
= (0.045 + 0.047) ADT
= 0.092 ADT
Now, the Design lane factor, FL = 0.80
For a four-lane highway, the directional distribution factor,
Fdir = 0.50(As it is not given)
We know that, Volume per lane in one direction,
Q = FL × Fdir × ADT ∕ Number of Lanes
= 0.80 × 0.50 × ADT ∕ 4
(As it is a four-lane highway)
= 0.10 ADTTotal equivalent standard axles per lane in one direction = 0.092 ADT
∴ Total number of lanes required = Total equivalent standard axles ∕ Volume per lane
= 0.092 ADT ∕ 0.10 ADT
= 0.92 or 1 lane (approx)
Know more about the traffic volume
https://brainly.com/question/33354662
#SPJ11
Why do we study LB and LTB in steel beams?3 What is effect of KL/r and 2nd order moments in columns?
Why SMF in NSCP 2015? Whats the significance?
The inclusion of SMFs in the NSCP 2015 reflects the importance of seismic design and the commitment to ensuring the safety and resilience of structures in seismic-prone areas like the Philippines.
We study lateral-torsional buckling (LTB) and local buckling (LB) in steel beams for the following reasons:
1. Lateral-Torsional Buckling (LTB): LTB refers to the buckling phenomenon that can occur in beams subjected to bending moments. When a beam is subjected to a combination of axial compression and bending, it can experience a lateral-torsional buckling failure mode. Understanding LTB is important to ensure that the beam can withstand the applied loads without failure. By studying LTB, engineers can determine the critical buckling load, design appropriate bracing or stiffening elements, and ensure the beam's stability.
2. Local Buckling (LB): LB refers to the buckling of individual compression flanges or webs of steel beams. It occurs when the compressive stresses in these elements exceed their critical buckling stress. Local buckling can significantly reduce the load-carrying capacity of the beam and affect its overall performance. By studying LB, engineers can determine the appropriate section properties and dimensions to prevent or mitigate local buckling, ensuring the beam's strength and stability.
The effect of KL/r (slenderness ratio) and 2nd order moments in columns:
1. KL/r: The slenderness ratio (KL/r) is a measure of the column's relative slenderness. It represents the ratio of the effective length (KL) to the radius of gyration (r) of the column section. The slenderness ratio affects the column's behavior under compression. As the slenderness ratio increases, the column becomes more prone to buckling. It is essential to consider the slenderness ratio in column design to ensure stability and prevent buckling failures. Different design provisions and formulas are used for different slenderness ratios to ensure adequate column strength and stability.
2. 2nd Order Moments: Second-order moments in columns refer to the moments that arise due to the deflection of the column under load. These moments can affect the stability of the column and its load-carrying capacity. In some cases, they can cause the column to buckle prematurely. Second-order moments need to be considered in column design to account for the effects of deflection and ensure the column's strength and stability. Design codes provide provisions for considering second-order moments in column design to prevent failures and ensure the structure's overall safety.
Significance of Special Moment Frames (SMF) in NSCP 2015:
Special Moment Frames (SMF) are a structural system designed to resist lateral loads, such as those caused by earthquakes. They are widely used in seismic regions to provide ductility and dissipate energy during seismic events. In the Philippines, the National Structural Code of the Philippines (NSCP) 2015 incorporates design provisions for SMF.
The significance of SMF in NSCP 2015 lies in the fact that they are specifically designed to resist seismic forces and ensure the safety of structures during earthquakes. SMFs undergo rigorous design requirements and detailing provisions to enhance their strength, stiffness, and energy dissipation capacity. By using SMFs in structural design, engineers can provide buildings and structures with enhanced resistance to seismic forces, minimizing the potential for damage or collapse during earthquakes.
To know more about axial visit:
brainly.com/question/33023280
#SPJ11
Say {W₁, -- Won} "} X₁ = W₁ X₂= 1 is abasis for W and X₁ X₁ -
We can say that the set {W₁, X₁ = W₁, X₂ = 1} is not a basis because it is linearly dependent.
The given statement {W₁, X₁ = W₁, X₂ = 1} is a basis for W.
To understand why this is a basis, let's break it down step by step:
1. A basis is a set of vectors that can span the entire vector space. In other words, any vector in the vector space can be expressed as a linear combination of the vectors in the basis.
2. The set {W₁, X₁ = W₁, X₂ = 1} consists of two vectors: W₁ and X₁ = W₁, X₂ = 1.
3. To check if these vectors form a basis, we need to verify two things: linear independence and spanning.
4. Linear independence means that no vector in the set can be expressed as a linear combination of the other vectors. In this case, since W₁ and X₁ = W₁, X₂ = 1 are the same vector, they are linearly dependent. Therefore, this set is not linearly independent.
5. However, we can still check if the set spans the vector space. Since W₁ is given, we need to check if we can express any vector in the vector space as a linear combination of W₁.
6. If W₁ is not a zero vector, it will span the entire vector space and form a basis.
In summary, the set {W₁, X₁ = W₁, X₂ = 1} is not a basis because it is linearly dependent.
Learn more about the basis from the given link-
https://brainly.com/question/13258990
#SPJ11
4. A 24-in sanitary sewer, 8,000 ft long, carries raw sewage to the city's wastewater treatment plant. The pipe is 45 years old and is made of concrete. There are 9 manholes on the way and no laterals
The 24-inch concrete sewer pipe, which is 8,000 feet long and 45 years old, carries untreated sewage to the city's wastewater treatment plant, with nine manholes along the way.
The given information describes a sanitary sewer system consisting of a 24-inch concrete pipe that is 8,000 feet in length. The pipe has been in use for 45 years and is responsible for transporting raw sewage to the city's wastewater treatment plant.
Along the length of the sewer line, there are nine manholes present, which provide access points for maintenance and inspection purposes.
The dimensions of the pipe (24 inches) indicate its inner diameter, and it is assumed to be a circular pipe. The pipe material is concrete, commonly used in sewer systems for its durability and corrosion resistance. The age of the pipe (45 years) suggests the need for regular maintenance and potential concerns regarding its structural integrity.
The purpose of this sewer system is to convey untreated sewage from various sources within the city to the wastewater treatment plant. Sewage from households, commercial buildings, and other sources enters the sewer system through sewer laterals, which are not present in this particular system.
The manholes along the sewer line serve as access points for inspection, maintenance, and cleaning activities. They provide entry into the sewer system, allowing personnel to monitor the condition of the pipe, remove debris or blockages, and ensure the system is functioning properly.
Overall, this information outlines the key characteristics of a 24-inch concrete sanitary sewer pipe, its length, age, and purpose, along with the presence of manholes along the route for maintenance and inspection purposes.
For more questions like Pipe click the link below:
https://brainly.com/question/13260061
#SPJ11
Zoologists and studying the population of trout fish in a lake. The function f (t) = 490 (0.96)^t represents the number of trout in the lake after t years. What is the yearly percent change?
The yearly percentage change in the population of trout fish in the lake is -4%.
Zoologists are scientists who study animal life and animal behavior, and they would be interested in studying the population of trout fish in a lake.
Zoologists can use mathematical models to help them understand how the population of fish is changing over time and what factors might be influencing these changes.
The function f(t) = 490(0.96)t represents an exponential decay function, where the initial value of the function is 490, and the common ratio of the function is 0.96.
Since we want to find the yearly percentage change, we need to find the percentage change for one year, which is given by the formula: P = ((f(t + 1) - f(t))/f(t)) × 100
Here, P represents the percentage change, f(t + 1) represents the value of the function after one year, and f(t) represents the initial value of the function.
Substituting the given values in the formula:
P = ((490(0.96)t+1 - 490(0.96)t)/490(0.96)t) × 100P = (490(0.96)t × (0.96 - 1)/490(0.96)t) × 100P = -4%
Therefore, the yearly percentage change in the population of trout fish in the lake is -4%.
For more questions on percentage
https://brainly.com/question/24877689
#SPJ8
If I have a room that is 4 by 4 , and I am pucrchasing tiles that are 1/3x1/3, calculate the number of tiles needed to cover the area in square meters. Show math please The room is in sqaure meters, and the tiles are in meters
Answer:
144 tiles
Step-by-step explanation:
The room is [tex]16cm^{2}[/tex] because 4 by 4 is 4 x 4 = 16.
Each tile is [tex]\frac{1}{9}[/tex] because [tex]\frac{1}{3}[/tex] x [tex]\frac{1}{3}[/tex] = [tex]\frac{1}{9}[/tex].
So we must do 16 ÷ [tex]\frac{1}{9}[/tex] = 144
So 144 tiles are needed.
please show and graph
Problem 10. Solution Set of a System of Linear Inequalities. 15 points. Determine graphically the solution set for the following system of inequalities and indicate whether the solution set is bounded
Determine graphically the solution set for the following system of inequalities and indicate whether the solution set is bounded. Hence the given system of inequalities has a bounded solution set.
To determine the solution set for a system of linear inequalities graphically, we follow these steps:
1. Write down the system of inequalities. For example, let's consider the following system of inequalities:
- 2x + y ≤ 6
- x - y ≥ -2
2. Graph each inequality separately on the coordinate plane. To do this, we can first graph the related equation by replacing the inequality symbol with an equal sign. Then, we shade the region that satisfies the inequality.
3. Determine the intersection of the shaded regions from step 2. This intersection represents the solution set of the system of inequalities.
4. Check whether the solution set is bounded. If the solution set has a finite area or is confined within a specific region, then it is bounded. If it extends infinitely, it is unbounded.
Let's apply these steps to the given system of inequalities:
System of inequalities:
- 2x + y ≤ 6
- x - y ≥ -2
Graphing the first inequality, 2x + y ≤ 6:
To graph this inequality, we can first graph the related equation, 2x + y = 6.
We can find two points that lie on the line by choosing x and solving for y. Let's use x = 0 and x = 3:
- When x = 0, we have 2(0) + y = 6, which gives y = 6. So, one point is (0, 6).
- When x = 3, we have 2(3) + y = 6, which gives y = 0. So, another point is (3, 0).
Plotting these two points and drawing a straight line passing through them, we get the graph of 2x + y = 6.
Graphing the second inequality, x - y ≥ -2:
Similarly, we can graph the related equation, x - y = -2, to find two points on the line.
By choosing x = 0 and x = 3, we find the points (0, 2) and (3, 5).
Plotting these two points and drawing a straight line passing through them, we get the graph of x - y = -2.
Next, we need to find the intersection of the shaded regions from the two graphs. The solution set is the region that satisfies both inequalities.
Once we have the solution set, we can check if it is bounded. In this case, we can observe that the solution set is a bounded region, as it is enclosed by the lines and does not extend infinitely.
Therefore, the solution set of the given system of inequalities is bounded.
To know more about "System of Inequalities":
https://brainly.com/question/28230245
#SPJ11
In Darcy's law, the average linear velocity of water is directly proportional to A. effective porosity B. specific discharge C. flow
In Darcy's law, the average linear velocity of water is directly proportional to (B) specific discharge.
This is because Darcy’s law defines the relationship between the rate of flow of a fluid through a porous material, the viscosity of the fluid, the effective porosity of the material and the pressure gradient. Specific discharge refers to the volume of water that flows through a given cross-sectional area of the aquifer per unit of time per unit width.
Darcy's law is used to determine the flow of fluids through permeable materials such as porous rocks. This law assumes that the flow of fluids is proportional to the pressure gradient and the properties of the permeable material. The specific discharge is the volume of fluid that passes through a unit width of the aquifer per unit time. Effective porosity is the ratio of the volume of void space to the total volume of the porous material.
The equation for Darcy’s law is expressed as:
Q = KA (h2 - h1) / L
Where:
Q = flow rate
K = hydraulic conductivity
A = cross-sectional area of the sampleh1 and h2 = the hydraulic heads at the ends of the sample
L = the length of the sample.
The specific discharge is a crucial parameter in groundwater hydrology because it determines the rate at which groundwater moves through the aquifer. The effective porosity is also an important parameter because it determines the amount of water that can be stored in the pore spaces of the material. In conclusion, the average linear velocity of water is directly proportional to the specific discharge in Darcy's law.
To know more about velocity visit:
https://brainly.com/question/30559316
#SPJ11
value. For Most of the w students his ma wage is Rs. 410, find the wages of the person who A shoe seller sells 100 pairs of shoes everyday in average. Out of which he sells about 55 pairs of shoes of 40 number of size. Which number of shoes does he order from the wholeseller? bu 35 students of grade 7 in final examination are presented TL
The shoe seller sells about 110 shoes of size 40 daily.
To find the wages of the person who sells shoes, we need additional information. The given information does not provide any direct relationship between the number of pairs of shoes sold and the wages of the person. Please provide more details or clarify the information to help determine the wages of the person.
Regarding the shoe seller's order from the wholesaler, we can calculate the number of shoes he orders of a specific size based on the given information. Here's how:
The shoe seller sells 100 pairs of shoes every day on average, and out of those, 55 pairs are of size 40.
Since a pair consists of two shoes, we can calculate the total number of shoes sold of size 40 as follows:
Number of shoes sold of size 40 = 55 pairs x 2 = 110 shoes.
As a result, the shoe store sells roughly 110 pairs of size 40 shoes each day.
for such more question on wages
https://brainly.com/question/15530787
#SPJ8
please i need help please
Answer:
(d) 7/2 inches
Step-by-step explanation:
You want the height of a cylinder with a volume of 1 2/9 in³ and a radius of 1/3 in.
VolumeThe formula for volume of a cylinder is ...
V = πr²h
Solving for h, we find ...
h = V/(πr²)
ApplicationUsing the given values, we find the height of the cylinder to be ...
h = (1 2/9)/((22/7)(1/3)²) = (11/9)/(22/7·1/9) = 11·7/22
h = 7/2 . . . . inches
The height of the cylinder is 7/2 inches.
<95141404393>
Determine the pipe size for a pipe segment in a storm sewer system. Assume that the pipe is to be reinforced concrete pipes (RCP) with Manning's n-value of 0.015, the peak runoff is 15 cfs, and the pipe slop is 1.5%.
The pipe size required for a pipe segment in a storm sewer system is 6 inches.
To determine the pipe size for a pipe segment in a storm sewer system, given the pipe is reinforced concrete pipes (RCP) with Manning's n-value of 0.015, peak runoff is 15 cfs and pipe slope is 1.5%, we can use the following steps:
Step 1: Calculate the maximum flow velocity
The maximum flow velocity is calculated as follows:
v = Q / (A * n)
where,
Q = peak runoff = 15 cfs
A = cross-sectional area of the pipe segment
n = Manning's n-value of RCP = 0.015
Step 2: Calculate the hydraulic radius
The hydraulic radius is given by:
r = A / P
where,
P = wetted perimeter of the pipe segment
P = πD + 2y
where,
D = diameter of the pipe
y = depth of flow (unknown)
Step 3: Calculate the depth of flow
Using Manning's equation, we have:
Q = (1/n) * A * R^(2/3) * S^(1/2)
where,
S = slope of the pipe segment = 1.5%
Solving for y (depth of flow), we get:
y = (Q / (1.49 * A * R^(2/3) * S^(1/2)))^(3/2)
Step 4: Calculate the pipe diameter
The diameter of the pipe can be calculated as follows:
D = 2y + ε
where,
ε = the wall thickness of the pipe (unknown)
We have to select a value for ε based on the RCP size available in the market. For instance, for an RCP with a diameter of 24 inches, ε could be around 2 inches. Therefore, we can assume ε to be 2 inches.
D = 2y + ε
Substituting the values, we get:
D = 2(2.98) + 2
D = 6 inches
Hence, the pipe size required for a pipe segment in a storm sewer system is 6 inches.
To know more about storm sewer system visit:
https://brainly.com/question/32806766
#SPJ11
1. A T-beam with bf=700 mm, hf=100 mm, bw =200 mm,h=400 mm,cc=40 mm, stirrups =12 mm, fc′=21Mpa,fy=415Mpa is reinforced by 4.32 mm diameter bars for tension only. Calculate the depth of the neutral axis. Calculate the nominal moment capacity
we can calculate the depth of the neutral axis (x).
[tex]x = ((As × fy)/(0.87 × fc′ × b)) + (d/2)x = ((0.4995 × 10⁻³ × 415 × 10⁶)/(0.87 × 21 × 10⁶ × 700)) + (374/2)x = 231.98 mm[/tex]
The depth of the neutral axis is 231.98 mm.
Mn = 0[tex].36 × fy × As × (d – (As/(0.87 × fc′ × b))[/tex])
Mn = [tex]0.36 × 415 × 10⁶ × 0.4995 × 10⁻³ × (374 – (0.4995 × 10⁻³/(0.87 × 21 ×[/tex]10⁶ × 700)))
Mn = 43.17 kN-m
The nominal moment capacity is 43.17 kN-m.
Given details:
bf = 700 mmhf = 100 mmbw = 200 mm
h = 400 mmcc = 40 mm
stirrups = 12 mmfc′ = 21 Mpa fy = 415 Mpa
Diameter of tension steel bars = 4.32 mm
Let’s first calculate the effective depth of the beam (d).d = h – (cc + (stirrup diameter/2))d [tex]= 400 – (40 + (12/2))d = 37[/tex]4 mmNext, we calculate the area of tension steel (As).
A[tex]s = (π/4) × d² × (4.32/1000)As = 0.4995 × 10⁻³ m²[/tex]
Now,
To calculate the nominal moment capacity, we use the formula,
To know more about capacity visit:
https://brainly.com/question/31196313
#SPJ11
A city requires a flow if 1.50 m3 for its water supply.
Determine the diameter of the pipe if the velocity of flow is to be
1.80 m/s.
The diameter of the pipe required for a flow rate of 1.50 m³/s and a velocity of 1.80 m/s is approximately 1.03 meters.
To determine the diameter of the pipe required for a flow rate of 1.50 m³/s and a velocity of 1.80 m/s, we can use the formula for flow rate:
Q = A * V
Where Q is the flow rate, A is the cross-sectional area of the pipe, and V is the velocity of flow.
Rearranging the formula, we have:
A = Q / V
Substituting the given values, we have:
A = 1.50 m³/s / 1.80 m/s
Simplifying the calculation, we find:
A = 0.8333 m²
The cross-sectional area of the pipe is 0.8333 m².
The formula for the area of a circle is:
A = π * r²
Where A is the area and r is the radius of the circle.
Since we are looking for the diameter, we know that the diameter is twice the radius. So, we have:
2r = D
Rearranging the formula for the area, we have:
r² = A / π
Substituting the given values, we have:
r² = 0.8333 m² / π
Calculating the value of r, we find:
r ≈ 0.5148 m
Finally, we can calculate the diameter:
D = 2 * r ≈ 2 * 0.5148 m ≈ 1.03 m
Therefore, the diameter of the pipe required for a flow rate of 1.50 m³/s and a velocity of 1.80 m/s is approximately 1.03 meters.
To learn more about area of pipe visit : https://brainly.com/question/23860097
#SPJ11
please solve them as soon as possible. thank you!
y'=(y^2-6y-16)x^2
y(4)=3
x^2y'+x^2y=x^3
y(0)=3
The solution to the differential equation y' = [tex](y^2 - 6y - 16)x^2[/tex] with the initial condition y(4) = 3 is y = [tex](x^2 - 4)/(x^2 + 1)[/tex].
To solve the given differential equation, we can use the method of separable variables. In the first step, let's rearrange the equation as follows:
dy/[tex](y^2[/tex]- 6y - 16) = [tex]dx/(x^2)[/tex].
Now, we can integrate both sides with respect to their respective variables. Integrating the left side requires us to find the antiderivative of 1/([tex]y^2[/tex] - 6y - 16), which can be done by completing the square. The denominator can be factored as (y - 8)(y + 2), so we can rewrite the left side as:
dy/((y - 8)(y + 2)).
Using partial fraction decomposition, we can express this expression as:
1/10 * (1/(y - 8) - 1/(y + 2)).
Integrating both sides gives us:
(1/10) * ln|y - 8| - (1/10) * ln|y + 2| = ln|x| + C1,
where C1 is the constant of integration.
Now, for the right side, integrating dx/(x^2) gives us -1/x + C2, where C2 is another constant of integration.
Combining both sides of the equation, we get:
(1/10) * ln|y - 8| - (1/10) * ln|y + 2| = ln|x| + C,
where C = C1 + C2.
We can simplify this expression by combining the logarithms:
ln|y - 8|/(y + 2) = 10 * ln|x| + C.
Exponentiating both sides, we have:
|y - 8|/(y + 2) = e^(10 * ln|x| + C).
Simplifying further, we get:
|y - 8|/(y + 2) = e^C * e^(10 * ln|x|).
Since e^C is a positive constant, we can replace it with another constant, let's call it A:
|y - 8|/(y + 2) = A * |x|^10.
Now, we can consider two cases: when x is positive and when x is negative. Taking x > 0, we can simplify the equation to:
(y - 8)/(y + 2) = A * x^10.
Cross-multiplying, we obtain:
y - 8 = A * x^10 * (y + 2).
Expanding the right side gives us:
y - 8 = A * x^10 * y + 2A * x^10.
Rearranging the terms, we have:
y - A * x^10 * y = 8 + 2A * x^10.
Factoring out y, we get:
(1 - A * x^10) * y = 8 + 2A * x^10.
Finally, solving for y, we obtain the solution to the differential equation:
y = (8 + 2A * x^10)/(1 - A * x^10).
Using the initial condition y(4) = 3, we can substitute the values and solve for A. After solving for A, we can substitute the value of A back into the solution to obtain the final expression for y.
Learn more about Differential equation
brainly.com/question/32645495
#SPJ11
An iceberg having specific gravity of 0.92 is floating on salt water
(sg=1.10). If the volume of ice above the water surface is 320 cu.m., what
is the total volume of the ice?
Determine the required energy in watts to be supplied to the motor if its
efficiency is 85%
The total volume of the iceberg can be determined by considering the specific gravity of the ice and the portion of the iceberg above the water surface is 347.83 cubic meters. In this case, the volume of ice above the water surface is given as 320 cubic meters.
To calculate the total volume of the ice, we need to divide this volume by the specific gravity of the ice. The specific gravity of a substance is the ratio of its density to the density of a reference substance. In this case, the specific gravity of the ice is given as 0.92. This means that the density of ice is 0.92 times the density of the reference substance, which is water. Given that the volume of ice above the water surface is 320 cubic meters, we can calculate the total volume of the ice using the formula:
Total volume of ice = Volume above water surface / Specific gravity of ice
Plugging in the values, we have:
Total volume of ice = 320 cubic meters / 0.92
Total volume of ice = 347.83 cubic meters
Therefore, the total volume of the ice is approximately 347.83 cubic meters.
To learn more about gravity refer:
https://brainly.com/question/557206
#SPJ11
The total volume of the iceberg can be determined by considering its specific gravity and the volume of ice above the water surface. Given that the specific gravity of the iceberg is 0.92 and the volume of ice above the water surface is 320 cubic meters, we can calculate the total volume of the ice.
To find the total volume of the ice, we can use the equation:
[tex]\[ \text{Total Volume of Ice} = \frac{\text{Volume Above Water}}{\text{Specific Gravity}} \][/tex]
Substituting the given values into the equation, we have:
[tex]\[ \text{Total Volume of Ice} = \frac{320}{0.92} \approx 347.83 \, \text{cubic meters} \][/tex]
Therefore, the total volume of the ice is approximately 347.83 cubic meters. Now let's move on to the second question regarding the required energy to be supplied to a motor with an efficiency of 85%.
To calculate the required energy in watts, we need additional information such as the power output of the motor or the time for which it needs to operate.
To learn more about specific gravity refer:
https://brainly.com/question/10495014
#SPJ11
equation has a solution y=−8e^2x xcos(x) (a) Find such a differential equation, assuming it is homogeneous and has constant coefficients. help (equations) (b) Find the general solution to this differential equation. In your answer, use c1,c2,c3 and c4 to denote arbitrary constants and x the independent variable. Enter c1 as c1,c2 as c2, etc
a) The differential equation is -24e^(2x)xcos(x) + 8e^(2x)sin(x) + c.
b) The general solution to the differential equation is given by:
y = -8e^(2x)xcos(x) + c1e^(2x)sin(x) + c2 (where c1 and c2 are arbitrary constants)
Let's see in detail :
(a) To find the differential equation corresponding to the given solution, we can differentiate y = -8e^(2x)xcos(x) with respect to x.
Let's calculate:
dy/dx = d/dx(-8e^(2x)xcos(x))
= -8(e^(2x)xcos(x))' (applying the product rule)
= -8(e^(2x))'xcos(x) - 8e^(2x)(xcos(x))' (applying the product rule again)
Now, let's find the derivatives of e^(2x) and xcos(x):
(e^(2x))' = 2e^(2x)
(xcos(x))' = (xcos(x)) + (-sin(x)) (applying the product rule)
Substituting these derivatives back into the equation, we have:
dy/dx = -8(2e^(2x)xcos(x)) - 8e^(2x)(xcos(x)) + 8e^(2x)(sin(x))
= -16e^(2x)xcos(x) - 8e^(2x)xcos(x) + 8e^(2x)sin(x)
= -24e^(2x)xcos(x) + 8e^(2x)sin(x)
This is the differential equation corresponding to the given solution.
(b) To find the general solution to the differential equation, we need to solve it. The differential equation we obtained in part (a) is:
-24e^(2x)xcos(x) + 8e^(2x)sin(x) = 0
Factoring out e^(2x), we have:
e^(2x)(-24xcos(x) + 8sin(x)) = 0
This equation holds when either e^(2x) = 0 or -24xcos(x) + 8sin(x) = 0.
Solving e^(2x) = 0 gives us no valid solutions.
To solve -24xcos(x) + 8sin(x) = 0, we can divide both sides by 8:
-3xcos(x) + sin(x) = 0
Rearranging the terms, we get:
3xcos(x) = sin(x)
Dividing both sides by cos(x) (assuming cos(x) ≠ 0), we obtain:
3x = tan(x)
This is a transcendental equation that does not have a simple algebraic solution.
We can find approximate solutions numerically using numerical methods or graphically by plotting the functions y = 3x and y = tan(x) and finding their intersection points.
Therefore, the general solution to the differential equation is given by:
y = -8e^(2x)xcos(x) + c1e^(2x)sin(x) + c2 (where c1 and c2 are arbitrary constants)
Learn more about differential equation from the given link
https://brainly.com/question/1164377
#SPJ11
Question 2 :Calculate the dry unit weight, the saturated unit weight and the buoyant unit weight of a soil having a void ratio of 0.60 and a value of G s of 2.75. Calculate also the unit weight and water content at a degree of saturation of 70%.
The unit weight and water content at a degree of saturation of 70% is 19.41.
The saturated unit weight and the buoyant unit weight of a soil having a void ratio of 0.60 and a value of G s of 2.75.
v_d = 2.75/(1 + 0.60) * 9.8 = 16.84
v_ sat = (2.75 + 0.60)/1.60 * 9.8 = 20.51
y' = (2.75 - 1)/1.60 * 9.8 = 10.71
Water content at a degree of saturation of 70%. = 0.70
y = [2.75 + (0.70 * 0.6)]/(1 + 0.6) * 9.8 = 19.41.
Learn more about unit weight here;
https://brainly.com/question/15220801
#SPJ4
The dry unit weight is 29.383 kN/m³, the saturated unit weight is 29.383 kN/m³, the buoyant unit weight is 26.9975 kN/m³, the unit weight at a degree of saturation of 70% is 20.5681 kN/m³, and the water content at a degree of saturation of 70% is -30.18%.
To calculate the dry unit weight, saturated unit weight, and buoyant unit weight of a soil, you can use the following formulas:
1. Dry Unit Weight (γd):
γd = (1+e) * Gs * γw2.
Saturated Unit Weight (γsat):
γsat = (1+e) * Gs * γw
3. Buoyant Unit Weight (γb):
γb = Gs * γw
where:
- e is the void ratio
- Gs is the specific gravity of soil particles
- γw is the unit weight of water (typically 9.81 kN/m³)
Given:
- Void ratio (e) = 0.60
- Specific gravity (Gs) = 2.75
- Degree of saturation (S) = 70%
To calculate the unit weight and water content at a degree of saturation of 70%, we can use the following formulas:
4. Unit Weight (γ):
γ = γd * S
5. Water Content (w):
w = (γ - γd) / γd
Substituting the given values into the formulas, we have:
1. Dry Unit Weight (γd):
γd = (1+0.60) * 2.75 * 9.81 = 29.383 kN/m³
2. Saturated Unit Weight (γsat):
γsat = (1+0.60) * 2.75 * 9.81 = 29.383 kN/m³
3. Buoyant Unit Weight (γb):
γb = 2.75 * 9.81 = 26.9975 kN/m³
4. Unit Weight (γ) at S = 70%:
γ = 29.383 * 0.70 = 20.5681 kN/m³
5. Water Content (w) at S = 70%:
w = (20.5681 - 29.383) / 29.383 = -0.3018 or -30.18% (negative value indicates the soil is drier than the optimum water content)
Learn more about dry unit weight
https://brainly.com/question/32462674
#SPJ11
Olfert Greenhouses has compiled the following estimates for operations. Sales $150 000 Fixed cost $45 200 Variable costs 67 500 Net income $37 300 a. Compute the break-even point in units b. Compute the break-even point in units if fixed costs are reduced to $37000
Compute the break-even point in units Break-even point (BEP) can be computed using the formula:
BEP = Fixed Costs / (Sales Price per Unit - Variable Cost per Unit)where.
Fixed costs = $45,200
Variable costs = $67,500
Sales = $150,000
Contribution margin = Sales - Variable Costs = $150,000 - $67,500 = $82,500
Therefore, BEP = Fixed costs / Contribution margin per unit
BEP = $45,200 / ($150,000 / Number of units sold - $67,500 / Number of units sold)
BEP = $45,200 / ($82,500 / Number of units sold)
Number of units sold = BEP = $45,200 x ($82,500 / Number of units sold)
Number of units sold² = $3,729,000,000
Number of units sold = √$3,729,000,000
Number of units sold = 61,044.87 ≈ 61,045 units
The break-even point in units is approximately 61,045 units.
b. Compute the break-even point in units if fixed costs are reduced to $37,000.
Given:
Fixed cost = $37,000
Sales = $150,000
Variable costs = $67,500
Contribution margin = $150,000 - $67,500 = $82,500
Now,
Number of units sold = Fixed cost / Contribution margin per unit
Number of units sold = $37,000 / ($150,000 / Number of units sold - $67,500 / Number of units sold)
Number of units sold = $37,000 / ($82,500 / Number of units sold)
Number of units sold² = $37,000 x $82,500
Number of units sold² = $3,057,500,000
Number of units sold = √$3,057,500,000
Number of units sold = 55,394.27 ≈ 55,394 units
The break-even point in units is approximately 55,394 units if fixed costs are reduced to $37,000.
To know more about computed visit:
https://brainly.com/question/15707178
#SPJ11
Algo Beer bottles are filled so that they contain an average of 475 ml of beer in each bottle. Suppose that the amount of beer in a bottle is normally distributed with a standard deviation of 8 ml. [You may find it useful to reference the z table.]
a. What is the probability that a randomly selected bottle will have less than 470 ml of beer? (Round final answer to 4 decimal places.) Probability _____
b. What is the probability that a randomly selected 6-pack of beer will have a mean amount less than 470 ml? (Round final answer to 4 decimal places.) Probability ____
c. What is the probability that a randomly selected 12-pack of beer will have a mean amount less than 470 ml? (Round final answer to 4 decimal places.) Probability ______
a. Probability of less than 470 ml in a bottle: 0.2659.
b. Probability of mean less than 470 ml in a 6-pack: 0.0630.
c. Probability of mean less than 470 ml in a 12-pack: 0.0158.
a. To find the probability that a randomly selected bottle will have less than 470 ml of beer, we need to calculate the z-score and then find the corresponding probability using the z-table.
The z-score is calculated as (X - μ) / σ, where X is the value we want to find the probability for, μ is the mean, and σ is the standard deviation.
In this case, X = 470 ml, μ = 475 ml, and σ = 8 ml.
Calculating the z-score:
z = (470 - 475) / 8 = -0.625
Using the z-table, we can find the probability corresponding to a z-score of -0.625. The z-table gives the area under the standard normal distribution curve to the left of a given z-score.
Looking up -0.625 in the z-table, we find that the probability is 0.2659.
Therefore, the probability that a randomly selected bottle will have less than 470 ml of beer is 0.2659 (rounded to 4 decimal places).
b. To find the probability that a randomly selected 6-pack of beer will have a mean amount less than 470 ml, we need to calculate the z-score for the sample mean.
The mean of the sample mean is still μ = 475 ml, but the standard deviation of the sample mean (also known as the standard error) is given by σ / sqrt(n), where n is the sample size.
In this case, n = 6, so the standard error = 8 / sqrt(6) ≈ 3.27 ml (rounded to 2 decimal places).
Calculating the z-score:
z = (470 - 475) / 3.27 ≈ -1.53
Looking up -1.53 in the z-table, we find that the probability is 0.0630.
Therefore, the probability that a randomly selected 6-pack of beer will have a mean amount less than 470 ml is 0.0630 (rounded to 4 decimal places).
c. Similarly, to find the probability that a randomly selected 12-pack of beer will have a mean amount less than 470 ml, we calculate the z-score using the same formula.
The standard error for a sample size of 12 is 8 / sqrt(12) ≈ 2.31 ml (rounded to 2 decimal places).
Calculating the z-score:
z = (470 - 475) / 2.31 ≈ -2.16
Looking up -2.16 in the z-table, we find that the probability is 0.0158.
Therefore, the probability that a randomly selected 12-pack of beer will have a mean amount less than 470 ml is 0.0158 (rounded to 4 decimal places).
learn more about Beer probabilities.
brainly.com/question/15631491
#SPJ11
There is a whole range of commercially available particle characterization techniques that can be used to measure particulate samples. Each has its relative strengths and limitations and there is no universally applicable technique for all samples and all situations Mention at least four criteria that need to be considered when choosing the particle characterization technique b. What is the difference between wet dispersion and dry dispersion? Mention instances where these techniques can be used a. (5 marks) Question 2: Sieving and Dynamic Light Scattering are two of the techniques that can be used for particle characterization. Select one of the processes and explain the method in some detail. Your answer should include a clear explanation of the process, why and when the process is used, advantages and disadvantages and how the data obtained is analysed.
When choosing a particle characterization technique, there are four criteria that need to be considered:
1. Sample properties: The properties of the particulate sample, such as size, shape, and composition, need to be taken into account. Different techniques may be more suitable for different types of particles.
2. Measurement range: The range of particle sizes that the technique can accurately measure is important. Some techniques are better suited for smaller particles, while others are better for larger particles.
3. Resolution and accuracy: The resolution and accuracy of the technique in measuring particle properties should be considered. Higher resolution and accuracy allow for more precise characterization.
4. Sample preparation: The method of sample preparation required for each technique should be evaluated. Some techniques may require wet dispersion, while others may require dry dispersion.
Wet dispersion involves dispersing the particles in a liquid medium, while dry dispersion involves dispersing the particles in a gas or air. Wet dispersion is commonly used for smaller particles and can help prevent agglomeration. Dry dispersion, on the other hand, is typically used for larger particles and can help maintain the integrity of the sample.
Instances where wet dispersion can be used include measuring the size distribution of nanoparticles in a suspension or determining the concentration of a particular particle in a liquid sample. Dry dispersion can be used to measure the particle size distribution of a powder or to analyze the size of airborne particles.
In summary, when choosing a particle characterization technique, it is important to consider the sample properties, measurement range, resolution and accuracy, and sample preparation requirements. Wet dispersion involves dispersing particles in a liquid medium, while dry dispersion involves dispersing particles in a gas or air. Wet dispersion is commonly used for smaller particles, while dry dispersion is typically used for larger particles.
Know more about particle characterization technique here:
https://brainly.com/question/33224354
#SPJ11
an egg is immersed in a very large amount of NaCl salt solution. NaCl in solution diffuses into the egg through the eggshell, then into the egg white and egg yolk. The egg can be considered to be perfectly spherical in shape with the radius in R and the thickness of the eggshell is T. The concentration of NaCl in the soaking solution is CNaCl,0 and its value can be assumed to be constant throughout the immersion process. Before being added to the soaking solution, there was no NaCl in the egg whites and egg yolks. Diffusion through the eggshell is negligible because it takes place very quickly. If the diffusivity coefficient of NaCl in egg white and egg yolk can be considered equal
. Use the component continuity equation table, to obtain an equation that describes the profile of the concentration of NaCl in eggs and its boundary conditions
a) The equation that describes the profile of the concentration of NaCl is ∂/∂r (r² * ∂C/∂r) = ∂C/∂t.
b) The equation in dimensionless form :∂c/∂τ = (1/η²) * ∂/∂η (η² * ∂c/∂η)
where the boundary conditions become:
c(η, 0) = 0 (initial condition)
c(1, τ) = 1 (boundary condition)
a. Equation in Differential Form:
Fick's second law of diffusion states:
∂C/∂t = D * (∂²C/∂r²)
where D is the diffusivity coefficient of NaCl in the egg white and egg yolk.
In this case, since the diffusivity coefficient is assumed to be the same, we can denote it as D.
So, the component continuity equation for a spherically symmetric system is given as follows:
∂C/∂t = (1/r²) x ∂/∂r (r² D ∂C/∂r)
Substituting this expression into Fick's second law, we have:
(1/r²) * ∂/∂r (r² * D * ∂C/∂r) = D * (∂²C/∂r²)
∂/∂r (r² * ∂C/∂r) = ∂C/∂t
This is the differential equation that describes the concentration profile of NaCl in the egg.
Boundary Conditions:
In this case, we assume that at the initial time (t = 0), the concentration of NaCl in the egg white and egg yolk is zero.
Therefore, we have:
C(r, 0) = 0
Furthermore, we assume that the concentration of NaCl at the eggshell (r = R) is equal to the concentration of NaCl in the soaking solution (CNaCl,0).
Therefore, we have:
C(R, t) = CNaCl,0
b. Equation in Dimensionless Form:
To convert the equation into a dimensionless form, we can introduce dimensionless variables and parameters. Let's define:
η = r/R (dimensionless radial coordinate)
τ = t * D/R² (dimensionless time)
c = C/CNaCl,0 (dimensionless concentration)
By substituting these dimensionless variables into the original equation, we obtain:
∂c/∂τ = (1/η²) * ∂/∂η (η² * ∂c/∂η)
This is the equation in dimensionless form, where the boundary conditions become:
c(η, 0) = 0 (initial condition)
c(1, τ) = 1 (boundary condition)
Learn more about Fick's Law here:
https://brainly.com/question/33379962
#SPJ4
Examine the periodic function given below and determine an equation, showing how you determined each parameter: /4
The periodic function is given by y = A sin(Bx + C) + D.
A periodic function is a function that repeats itself at regular intervals. The given function is of the form y = A sin(Bx + C) + D, where A, B, C, and D are parameters that determine the characteristics of the function.
1. Amplitude (A): The amplitude represents the maximum distance the function reaches above or below the midline. To determine the amplitude, we need to find the vertical distance between the highest and lowest points of the function. This can be done by analyzing the given periodic function or by examining its graph.
2. Period (P): The period is the distance between two consecutive cycles of the function. It can be found by analyzing the given function or by examining its graph. The period is related to the coefficient B, where P = 2π/|B|. If the coefficient B is positive, the function has a normal orientation (increasing from left to right), and if B is negative, the function is flipped (decreasing from left to right).
3. Phase shift (C): The phase shift determines the horizontal displacement of the function. It indicates how the function is shifted horizontally compared to the standard sine function. The value of C can be obtained by analyzing the given function or by examining its graph.
4. Vertical shift (D): The vertical shift represents the displacement of the function along the y-axis. It indicates how the function is shifted vertically compared to the standard sine function. The value of D can be determined by analyzing the given function or by examining its graph.
By analyzing the given periodic function and determining the values of A, B, C, and D, we can fully describe the function and understand its behavior.
Learn more about Periodic
brainly.com/question/16061498
#SPJ11
Someone help with process pleaseee
Answer: n= 6 x= 38.7427 f= 4.618802 h= 9.237604
Step-by-step explanation:
for the first one:
there are 2 45 90 triangles. Since the sides of a 45 90 triangle are n for 45 and [tex]n\sqrt{2}[/tex] for the 90 degrees, that means that if [tex]6\sqrt{2} = n\sqrt{2}[/tex] then n is 6.
Second one:
You have to split the x into two parts.
Starting on the first part use the 30 60 90 triangle with given with the length for the 60°
60 = [tex]n\sqrt{3}[/tex]
so [tex]30=n\sqrt{3}[/tex]
n = 17.320506
so part of x is 17.320506
For the next triangle you would use Tan 35 = [tex]\frac{15}{y}[/tex]
this would equal 21.422201
adding both values up it would be 38.742707
Third question:
There is two 30 60 90 triangles
The 60° is equal to 8 which means [tex]8=n\sqrt{3}[/tex]
Simplifying this [tex]n=4.618802[/tex]
h = 2n. which is h= 9.237604
f=n f is 4.618802
Answer:
Special right-angle triangle:1) Ratio of angles: 45: 45: 90
Ratio of sides: 1: 1: √2
Sides are n, n, n√2
The side opposite to 90° = n√2
n√2 = 6√2
[tex]\boxed{\sf n = 6}[/tex]
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2) Ratio of angles: 30: 60: 90
Ratio of side: 1: √3: 2
Sides are m, m√3, 2m.
Side opposite to 60° = m√3
m√3 = 30
[tex]m = \dfrac{30}{\sqrt{3}}\\\\\\m = \dfrac{30\sqrt{3}}{3}\\\\m = 10\sqrt{3}[/tex]
Side opposite to 30° = m
m = 10√3
In ΔABC,
[tex]Tan \ 35= \dfrac{opposite \ side \ of \angle C }{adjacent \ side \ of \angle C}\\\\\\~~~~~~0.7 = \dfrac{15}{CB}\\\\[/tex]
0.7 * CB = 15
[tex]CB =\dfrac{15}{0.7}\\\\CB = 21.43[/tex]
x = m + CB
= 10√3 + 21.43
= 10*1.732 + 21.43
= 17.32 + 21.43
= 38.75
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
3) Ratio of angles: 30: 60: 90
Ratio of side: 1: √3: 2
Sides are y, y√3, 2y.
Side opposite to 60° = y√3
[tex]\sf y\sqrt{3}= 8\\\\ ~~~~~ y = \dfrac{8}{\sqrt{3}}\\\\~~~~~ y =\dfrac{8*\sqrt{3}}{\sqrt{3}*\sqrt{3}}\\\\\\~~~~~ y =\dfrac{8\sqrt{3}}{3}[/tex]
Side opposite to 30° = y
[tex]\sf f = y\\\\ \boxed{f = \dfrac{8\sqrt{3}}{3}}[/tex]
Side opposite to 90° = 2y
h = 2y
[tex]\sf h =2*\dfrac{8\sqrt{3}}{3}\\\\\\\boxed{h=\dfrac{16\sqrt{3}}{3}}[/tex]
A contractor has a crew of two individuals (backhoe operator and helper) working in the Lost Woods. They are building a small lake (after all proper permits have been filed and approved) for what the owner of the property wants to try to be a site for an international house cat dock jumping event (similar to dog dock jumping but with cats.... Everybody but the property owner recognizes that there would be a lot of clawing, unhappy cats, and videos of "what not to do" for the internet....... Property owners can do some unusual things). The anticipated lake size is 1 acre in area and averages 5 feet deep. a. Assuming a flat area, calculate the amount of material to be excavated (assume no soil expansion) [5%] b. Assuming, based on equipment being used, that 150 CY can be removed per 8 hour shift (and assume 1 shift per day); how many days will it take to complete the project (round to whole number)? [5%] c. If on Mondays and Fridays, production is only 100 CY per day and no work happens on Saturday/Sunday; how many weeks will it take to complete the work? [5%] d. If the operator and helper (including equipment usage, material, and overhead) is $200 per hour (hourly rate is full 8 hour shift, even if a partial day), using the production rates in part C, how much will labor and material cost? [5%] e. If a 30% markup is required to keep everything happy on the business end, how much should your rate be per cubic yard of material removed? [5%])
a)Total material to be excavated: 1,613 cubic yards
b) Number of days to complete the work: 11 days
c) Number of weeks to complete the work: 2 weeks
d) Labor and material cost: $17,600
e) Rate per cubic yard of material removed: $260
a) The volume of the lake:
Area of the lake = 1 acre
Average depth of the lake = 5 feet
Convert the area to square feet: 1 acre = 43,560 square feet
Volume of the lake = Area × Depth = 43,560 cubic feet
Convert the volume to cubic yards: 43,560 / 27 = 1,613 cubic yards
b) The number of days to complete the work:
The contractor can remove 150 cubic yards of material in 1 shift.
Divide the total volume of the lake by the amount removed in a shift: 1,613 / 150 = 10.75 ≈ 11 days
c) The number of weeks to complete the work:
The contractor removes 100 cubic yards of material per day for 2 days of the week.
The contractor removes 150 cubic yards of material per day for the remaining 5 days of the week.
Calculate the total amount of material removed in a week:
(100 × 2) + (150 × 5) = 950 cubic yards
Divide the total volume of the lake by the amount removed in a week:
1,613 / 950 = 1.7 ≈ 2 weeks (rounded to whole number)
d) The labor and material cost:
The cost of the operator and helper per hour is $200.
Calculate the total production:
Amount produced on Mondays and Fridays
=100 cubic yards per day × 2 days = 200 cubic yards
Amount produced on the remaining 5 days
= 150 cubic yards per day × 5 days = 750 cubic yards
Total production in the first week
= 200 + 750 = 950 cubic yards
The total hours worked in the first week:
Hours worked on Mondays and Fridays
= 2 days × 8 hours/day = 16 hours
Hours worked on the remaining 5 days
= 5 days × 8 hours/day = 40 hours
Total hours worked in the first week
= 16 + 40 = 56 hours
The labor and material cost in the first week:
Labor and material cost per hour = $200
Total labor and material cost in the first week
= 56 hours × $200/hour = $11,200
The amount produced in the second week and total hours worked:
Amount produced in the second week = Total volume - Amount produced in the first week
= 1,613 - 950 = 663 cubic yards
Total hours worked in the second week
= 3 days × 8 hours/day + 2 days × 8 hours/day = 32 hours
The labor and material cost in the second week:
Labor and material cost in the second week = Total hours worked in the second week × $200/hour
= 32 hours × $200/hour = $6,400
Total labor and material cost = Labor and material cost in the first week + Labor and material cost in the second week = $11,200 + $6,400 = $17,600
e) The rate per cubic yard of material removed:
A 30% markup is required.
Calculate the markup amount: 30% × $200 = $60
Calculate the rate per cubic yard: $200 + $60 = $260 per cubic yard
To know more about Volume visit:
https://brainly.com/question/29255732
#SPJ11
1. Use the K-map to determine the prime implicants, essential prime implicants, a minimum sum of products, prime implicates, essential prime implicates, and a minimum product of sums for each of the following Boolean functions. Also, for each one compute a minimum product of sums and a minimum sum of products of its complements.
a. f(a,b,c,d)= Π M(0,1,8,11,12,14)
b. g(a,b,c,d)= Σ m(0,1,3,5,6,8,11,13,15)
c. h(a,b,c)= Σ m(1,4,5,6)
2. Write the decimal representation of SSOP and SPOS for each of the above functions and its complement.
The questions pertain to Boolean functions and involve using Karnaugh maps (K-maps) to determine prime implicants, essential prime implicants, minimum sum of products, prime implicates, essential prime implicates, minimum product of sums, and decimal representations of SSOP and SPOS forms for the given Boolean functions and their complements.
For Boolean function f(a, b, c, d) = ΠM(0, 1, 8, 11, 12, 14):
Using the K-map, we can determine the prime implicants and essential prime implicants.
The minimum sum of products can be derived from the prime implicants.
The prime implicates and essential prime implicates can also be determined.
To find the minimum product of sums of its complements, we can use the prime implicants and essential prime implicants of the complement function.
For Boolean function g(a, b, c, d) = Σm(0, 1, 3, 5, 6, 8, 11, 13, 15):
Similar to the first question, we can use the K-map to determine the prime implicants, essential prime implicants, minimum sum of products, prime implicates, essential prime implicates, and minimum product of sums of its complements.
The decimal representation of the SSOP (Sum of Sum of Products) and SPOS (Sum of Product of Sums) forms can be obtained for the given Boolean function and its complement.
For Boolean function h(a, b, c) = Σm(1, 4, 5, 6):
Follow a similar process using the K-map to find the prime implicants, essential prime implicants, minimum sum of products, prime implicates, essential prime implicates, minimum product of sums of its complements, and the decimal representation of SSOP and SPOS forms for the given Boolean function and its complement.
The process involves using K-maps and Boolean algebra techniques to determine the required values for each given Boolean function and its complement. The specific steps and calculations can be performed based on the provided Boolean functions and their respective minterms.
To learn more about decimal representations visit:
brainly.com/question/29220229
#SPJ11
A random sample of n = 16 scores is selected from a normal population with a mean of μ = 50. After a treatment is administered to the individuals in the sample, the sample mean is found to be M = 54.
a) If the population standard deviation is σ = 8, is the sample mean sufficient to conclude that the treatment has a significant effect? Use a two-tailed test with α = .05.
b) If the population standard deviation is σ = 12, is the sample mean sufficient to conclude that the treatment has a significant effect? Use a two-tailed test with α = .05.
c)Comparing your answers for parts a and b, explain how the magnitude of the standard deviation influences the outcome of a hypothesis test.
a) To determine if the treatment has a significant effect, we can perform a hypothesis test using the sample mean. The null hypothesis (H0) states that the treatment has no effect, while the alternative hypothesis (H1) states that the treatment does have an effect. In this case, we are conducting a two-tailed test with α = 0.05, meaning we are looking for extreme values in both tails of the distribution.
b) Using the same approach as in part a, we can calculate the z-score with a population standard deviation of σ = 12. Given M = 54, μ = 50, σ = 12, and n = 16, the z-score is calculated as z = (54 - 50) / (12 / √16) = 1.
To perform the test, we can calculate the z-score using the formula: z = (M - μ) / (σ / √n), where M is the sample mean, μ is the population mean, σ is the population standard deviation, and n is the sample size. In this case, M = 54, μ = 50, σ = 8, and n = 16.
Plugging these values into the formula, we get z = (54 - 50) / (8 / √16) = 2. Using a z-table or a statistical calculator, we find that the critical z-value for a two-tailed test with α = 0.05 is approximately ±1.96.
Since our calculated z-value of 2 is greater than the critical value of 1.96, we reject the null hypothesis. This means that the sample mean of 54 is statistically significant and provides evidence that the treatment has a significant effect.
Comparing the calculated z-value of 1 to the critical z-value of 1.96, we see that the calculated value is less than the critical value. Therefore, we fail to reject the null hypothesis.
In other words, the sample mean of 54 is not statistically significant when the population standard deviation is 12, and we do not have sufficient evidence to conclude that the treatment has a significant effect.
The magnitude of the standard deviation (σ) plays a crucial role in hypothesis testing. A larger standard deviation indicates that the data points are more spread out from the mean, resulting in a wider distribution. As a result, it becomes more challenging to detect a significant effect of the treatment, as the variability in the data increases. This is evident when comparing parts a and b of the question.
In part a, where the population standard deviation is σ = 8, the calculated z-value of 2 exceeds the critical value of 1.96. This indicates that the sample mean of 54 is statistically significant, suggesting a significant effect of the treatment.
On the other hand, in part b, where the population standard deviation is larger at σ = 12, the calculated z-value of 1 is smaller than the critical value.
Consequently, we fail to reject the null hypothesis, implying that the sample mean of 54 is not statistically significant, and we cannot conclude that the treatment has a significant effect.
Thus, a larger standard deviation reduces the ability to detect a significant effect in a hypothesis test.
To learn more about null hypothesis visit:
brainly.com/question/32575796
#SPJ11
Question 1 From load analysis, the following are the factored design forces result: Mu = 440 KN-m, V₁ = 280 KN. The beam has a width of 400 mm and a total depth of 500 mm. Use f'c = 20.7 MPa, fy for main bars is 415 MPa, concrete cover to the centroid of the bars both in tension and compression is 65 mm, steel ratio at balanced condition is 0.02, lateral ties are 12 mm diameter. Normal weight concrete. Calculate the required area of compression reinforcement in mm² due to the factored moment, Mu. Express your answer in two decimal places.
The area of compression reinforcement required is 132.20 mm².
Given the following information:Width of the beam, b = 400 mm,Depth of the beam, h = 500 mm,Effective cover, d = 65 mm,Concrete strength, f’c = 20.7 MPa,Yield strength of steel, fy = 415 MPa,Steel ratio at balanced condition, ρ = 0.02Factored moment, Mu = 440 kN-m.
We can determine the required area of compression reinforcement as follows:
Calculate the effective depth and maximum lever arm (d) = h - (cover + diameter / 2),where diameter of main bar, φ = 12 mmcover = 65 mmeffective depth, d = 500 - (65 + 12/2)d = 429 mm,
Maximum lever arm = 0.95 x d
0.95 x 429 = 407.55 mm
Compute for the depth of the neutral axis.Neutral axis depth (x) = Mu / (0.85 x f'c x b),where b is the width of the beam= 440 x 10⁶ / (0.85 x 20.7 x 10⁶ x 400)x = 0.2973 m .
Calculate the area of steel reinforcement requiredArea of tension steel,
Ast = Mu / (0.95 x fy x (d - 0.42 x x)),
where 0.42 is a constant= 440 x 10⁶ / (0.95 x 415 x (429 - 0.42 x 297.3)),
Ast = 1782.57 mm²
Find the area of compression steel required.As the section is under-reinforced, the area of compression steel required is given by
Ac = ρ x balance area
0.02 x (0.85 x f'c x b x d / fy),
Ac = 132.20 mm²
The area of compression reinforcement required is 132.20 mm².
To know more about Concrete strength visit:
brainly.com/question/31102674
#SPJ11
The required area of compression reinforcement, due to the factored moment Mu, is approximately 3765.25 mm².
Understanding BeamsBy applying the formula for the balanced condition of reinforced concrete beams, we can calculate the required area of compression reinforcement.
Mu = 0.87 * f'c * (b * d² - As * (d - a))
Where:
Mu is the factored moment (440 kN-m)
f'c is the compressive strength of concrete (20.7 MPa)
b is the width of the beam (400 mm)
d is the total depth of the beam (500 mm)
As is the area of steel reinforcement
a is the distance from the extreme compression fiber to the centroid of tension reinforcement
To find the required area of compression reinforcement, we need to rearrange the formula and solve for As:
As = (0.87 * f'c * b * d² - Mu) / (f'c * (d - a))
Given:
f'c = 20.7 MPa
b = 400 mm
d = 500 mm
a = 65 mm
Mu = 440 kN-m
Substitute the values into the formula and calculate As:
As = (0.87 * 20.7 MPa * 400 mm * (500 mm)² - 440 kN-m) / (20.7 MPa * (500 mm - 65 mm))
As = 3765.25 mm²
Therefore, the required area of compression reinforcement, due to the factored moment Mu, is approximately 3765.25 mm².
Learn more about beams here:
https://brainly.com/question/29891083
#SPJ4