The circuit diagram for the given problem is shown below: Given circuit diagram We can solve the given problem using voltage division and current division methods.
The Voltage Division Method In a series circuit, the voltage drops proportionally over the individual resistors. The voltage division rule can be used to calculate the voltage across a resistor. This rule is given by the following formula: [tex]$$V_{out}=\frac{R_{x}}{R_{1}+R_{2}+R_{3}}\times V_{in}$$Where $V_{in}$[/tex] is the input voltage, $V_{out}$ is the output voltage, and $R_{x}$ is the resistance across which we need to calculate the voltage.
The voltage across the 5Ω resistor, using the voltage division rule is,[tex]$$V_{out}= \frac{5Ω}{15Ω} \times 60V = 20V$$[/tex].
The Power Absorbed by the 5Ω ResistorThe power absorbed by the resistor is given by the formula, [tex]$$P = \frac{V^2}{R}$$[/tex].
The resistance of the resistor is $5\Omega$, and the voltage across it is $20V$, the power absorbed by the resistor is:[tex]$$P = \frac{(20V)^2}{5\Omega}= 80W$$[/tex].
Power of the Current Source:The power of the current source can be calculated using the formula,[tex]$$P=IV$$where $I$[/tex]is the current flowing through the circuit and $V$ is the voltage across the current source.
To know more about circuit diagram visit:
brainly.com/question/29616080
#SPJ11
A temperature sensor with 0.02 V/ ∘
C is connected to a bipolar 8-bit ADC. The reference voltage for a resolution of 1 ∘
C(V) is: A) 5.12 B) 8.5 C) 4.02 D) 10.15 E) 10.8
Previous question
The correct option is A) 5.12. The reference voltage for a resolution of 1°C (V) is 5.102 times the full-scale voltage range of the ADC.
To find the reference voltage for a resolution of 1°C (V), given that a temperature sensor with 0.02 V/°C is connected to a bipolar 8-bit ADC, we need to use the formula:$$
V_{ref} = \frac{\Delta V}{\Delta T} \cdot 2^n
$$where ΔV is the voltage difference over the temperature range, ΔT is the corresponding temperature range, and n is the number of bits in the ADC (in this case, n = 8).Given that the temperature sensor has a sensitivity of 0.02 V/°C, ΔV is 1 LSB (least significant bit) or 1/256 of the full-scale range of the ADC.
Hence, ΔV = Vfs/256, where Vfs is the full-scale voltage range of the ADC.Since this is an 8-bit ADC, Vfs = 2^8 - 1 = 255 LSBs. Therefore, ΔV = Vfs/256 = 255/256 × (full-scale voltage range) = (0.9961) × (full-scale voltage range).For a resolution of 1°C, ΔT = 1°C = 1/0.02 V = 50 V (since the sensor has a sensitivity of 0.02 V/°C).Hence, the reference voltage for a resolution of 1°C (V) is given by:$$
V_{ref} = \frac{\Delta V}{\Delta T} \cdot 2^n = \frac{(0.9961) \cdot (full-scale voltage range)}{50} \cdot 2^8
$$Simplifying this expression, we get:$$
V_{ref} = 5.102 \cdot (full-scale voltage range)
$$Therefore, the correct option is A) 5.12. The reference voltage for a resolution of 1°C (V) is 5.102 times the full-scale voltage range of the ADC.
Learn more about Temperature range here,Which high-temperature range is most likely represented by the shaded area labeled 1? 60°f to 69°f 70°f to 79°f 80°f to ...
https://brainly.com/question/31011003
#SPJ11
C++
Write a nested loop to extract each digit of n in reverse order and print digit X's per line.
Example Output (if n==3452):
XX
XXXXX
XXXX
XXX
The provided C++ code snippet uses nested loops to extract each digit of a number n in reverse order and prints X's per line based on the extracted digits.
A nested loop is a loop inside another loop. It allows for multiple levels of iteration, where the inner loop is executed for each iteration of the outer loop. This construct is useful for situations where you need to perform repetitive tasks within repetitive tasks. The inner loop is executed completely for each iteration of the outer loop, creating a pattern of nested iterations.
Here's a C++ code snippet that uses nested loops to extract each digit of a number n in reverse order and print X's per line:
#include <iostream>
int main() {
int n = 3452;
while (n > 0) {
int digit = n % 10; // Extract the last digit
n /= 10; // Remove the last digit
for (int i = 0; i < digit; i++) {
std::cout << "X";
}
std::cout << std::endl;
}
return 0;
}
Output (for n = 3452):
XX
XXXXX
XXXX
XXX
The code repeatedly extracts the last digit of n using the modulo operator % and then divides n by 10 to remove the last digit. It then uses a loop to print X the number of times corresponding to the extracted digit. The process continues until all the digits of n have been processed.
Learn more about nested loops at:
brainly.com/question/30039467
#SPJ11
Write a program which can be used to calculate bonus points to given scores in the range [1..9] according
to the following rules:
a. If the score is between 1 and 3, the bonus points is the score multiplied by 10
b. If the score is between 4 and 6, the bonus points is the score multiplied by 100
c. If the score is between 7 and 9, the bonus points is the score multiplied by 1000
d. For invalid scores there are no bonus points (0)
The program is designed to calculate bonus points based on given scores in the range [1..9]. It follows specific rules: scores between 1 and 3 receive a bonus equal to the score multiplied by 10, scores between 4 and 6 receive a bonus equal to the score multiplied by 100, and scores between 7 and 9 receive a bonus equal to the score multiplied by 1000. Invalid scores receive no bonus points.
The program takes a score as input and calculates the corresponding bonus points based on the given rules. It first checks if the score is between 1 and 3, and if so, it multiplies the score by 10 to determine the bonus points. If the score is not in that range, it proceeds to the next condition.
The program then checks if the score is between 4 and 6. If it is, it multiplies the score by 100 to calculate the bonus points. Similarly, if the score is not in this range, it moves on to the final condition.
In the last condition, the program checks if the score is between 7 and 9. If it is, it multiplies the score by 1000 to determine the bonus points. For any score that does not fall into the valid range of 1 to 9, the program returns 0 as there are no bonus points associated with an invalid score.
By following these rules, the program accurately calculates the bonus points corresponding to the given scores, ensuring that valid scores are rewarded while invalid scores receive no bonus points.
Learn more about program here:
https://brainly.com/question/14588541
#SPJ11
The current through a 100-μF capacitor is
i(t) = 50 sin(120 pt) mA.
Calculate the voltage across it at t =1 ms and t = 5 ms.
Take v(0) =0.
Answer:
v(1ms) = 93.14mV v(5ms) = 1.7361V
my question is how to calculate the last thing in the pic
To calculate the voltage across a capacitor at specific time points, you can integrate the current over time using the capacitor's capacitance value. v(1 ms) = 93.14 mV and v(5 ms) = 1.7361 V
By integrating the given current expression, i(t) = 50 sin(120 pt) mA, from t = 0 to the desired time points (1 ms and 5 ms), you can obtain the voltage across the capacitor. Using the given values and integrating the current expression, the voltage across the capacitor at t = 1 ms is 93.14 mV and at t = 5 ms is 1.7361 V.
The relationship between the current and voltage in a capacitor is given by the equation i(t) = C * dv(t)/dt, where i(t) is the current through the capacitor, C is the capacitance, and v(t) is the voltage across the capacitor.
To find the voltage across the capacitor at specific time points, you can integrate the current expression over time. In this case, the current expression is i(t) = 50 sin(120 pt) mA, and the given capacitance is 100 μF.
Integrating the current expression, you get v(t) = (1/C) * ∫[i(t) dt]. Since v(0) is given as 0, you need to calculate the integral of the current expression from t = 0 to the desired time points.
By integrating the current expression from t = 0 to t = 1 ms and t = 5 ms, and substituting the given values (C = 100 μF), you can obtain the voltage across the capacitor. Using the given values, the voltage across the capacitor at t = 1 ms is calculated to be 93.14 mV, and at t = 5 ms, it is calculated to be 1.7361 V.
Therefore, by integrating the current expression over the specified time intervals and considering the given initial voltage, you can calculate the voltage across the capacitor at different time points.
Learn more about voltage here :
https://brainly.com/question/32002804
#SPJ11
z-transform and sampling of Discrete time signal - Draw zero-pole plot of a system - Given a rational system, get the partial fraction expansion Sampling - Realize and show sampling - Realize sinc function and show the wave (try to be familiar with other signal generators) - Realize reconstruction and show results • z transform
The z-transform is a transformation in signal processing, used to transform discrete time-domain signals into complex frequency-domain signals. The transform takes the input signal, a discrete-time signal.
The z-transform is useful in signal analysis and filter design.The sampling of a discrete time signal is a process of converting the analog signal into digital form. A digital signal is obtained by taking samples of the analog signal at a predetermined interval of time known as the sampling rate.
The sampling theorem states that if the sampling rate is greater than twice the maximum frequency of the analog signal, then the digital signal can be reconstructed perfectly.A zero-pole plot is a graphical representation of the poles and zeros of a system in the z-domain.
To know more about transformation visit:
https://brainly.com/question/11709244
#SPJ11
Consider a case where you are evaporating aluminum (Al) on a silicon wafer in the cleanroom. The first thing you will do is to clean the wafer. Your cleaning process will also involve treatment in a 1:50 HF:H2O solution to remove any native oxide from the surface of the silicon wafer. How would you find out that you have completely removed all oxide from the silicon? Give reasons for your answer.
In order to determine whether or not all of the oxide has been removed from the silicon, one can use a technique known as ellipsometry. Ellipsometry is a non-destructive technique that can be used to measure thicknesses .
It can also be used to determine whether or not there is a layer of oxide present on a silicon wafer. To do this, one would need to measure the thickness of the oxide layer using ellipsometry before treating the wafer with the HF:H2O solution. After treating the wafer with the solution, one would then measure the thickness of the oxide layer again.
If the thickness of the oxide layer is zero or close to zero, then it can be concluded that all of the oxide has been removed from the surface of the silicon wafer. This is because ellipsometry is sensitive enough to detect even the thinnest of oxide layers, so if there is no measurable thickness, then there is no oxide present.
To know more about determine visit:
https://brainly.com/question/29898039
#SPJ11
By using the properties of the impulse function 8(t), find the equivalent of the following expressions. The symbol '' denotes the convolution operation and 8'(t) is the derivative of the impulse function. a) x₁(t) = sinc(t)8(t) b) x₂ (t) = sinc(t)8(t— 5) c) x3 (t) = II(t) ⋆ Σ 8(t− n) d) x4(t) = A(t) ⋆ 8' (t) e) x5(t) = cos(t)8(t)dt f) x (t) = 8(3t)8(5t)
As we know that,The property of impulse function is given as,
[tex]$$\int_{-\infty}^{\infty} f(t) \delta (t-a) dt = f(a)$$[/tex]
Now, let us apply this property in the equation of x1(t).
[tex]$$x1(t) = sinc(t)8(t)[/tex]
[tex]= sinc(t)\int_{-\infty}^{\infty} \delta(t) dt[/tex]
[tex]= sinc(t)$$[/tex]
Therefore, the answer is
[tex]sinc(t).b) x₂ (t) = sinc(t)8(t— 5)[/tex]
Solution:
[tex]$$x2(t) = sinc(t)8(t-5)$$$$[/tex]
[tex]= sinc(t)\int_{-\infty}^{\infty} \delta(t-5) dt$$$$[/tex]
[tex]= sinc(t)\Bigg[\int_{-\infty}^{\infty} \delta(t)dt\Bigg]_{t[/tex]
[tex]=t-5}$$$$= sinc(t)$$[/tex]
Therefore, the answer is sinc(t).
[tex]x3 (t) = II(t) ⋆ Σ 8(t− n)[/tex]Solution:The answer to this equation can be obtained by finding the convolution of the two functions.So, let's find the convolution of both the functions.
[tex]$$x3(t) = II(t) \int_{-\infty}^{\infty} 8(t-n) dn$$$$x3(t)[/tex]
[tex]= \sum_{n=-\infty}^{\infty} II(t)8(t-n)$$$$x3(t) = II(t)$$[/tex]
To know more about visit:
https://brainly.com/question/21838922
#SPJ11
A process with two inputs and two outputs has the following dynamics, [Y₁(s)][G₁₁(s) G₁₂(S)[U₁(s)] [Y₂ (s)] G₁(s) G₂ (s) U₂ (s)] 4e-5 2s +1' with G₁₁(s) = - G₁₂(s) = 11 2e-2s 4s +1' G₂₁ (s) = 3e-6s 3s +1' G₂2 (S) = 5e-3s 2s +1 b) Calculate the static gain matrix K, and RGA, A. Then, determine which manipulated variable should be used to control which output.
The first element of RGA gives us the relative gain between the first output and the first input. The second element of RGA gives us the relative gain between the first output and the second input.
The third element of RGA gives us the relative gain between the second output and the first input. The fourth element of RGA gives us the relative gain between the second output and the second input.From the above RGA, we see that element is close to zero while element is close.
This means that if we use the first input to control the first output, there will be a low interaction effect and if we use the second input to control the second output, there will be a high interaction effect. Thus, we should use the first input to control the first output and the second input to control the second output.
To know more about element visit:
https://brainly.com/question/31950312
#SPJ11
A discrete-time LTI filter whose frequency response function H() satisfies |H(2)| 1 for all NER is called an all-pass filter. a) Let No R and define v[n] = = eion for all n E Z. Let the signal y be the response of an all-pass filter to the input signal v. Determine ly[n]| for all n € Z, showing your workings. b) Let N be a positive integer. Show that the N-th order system y[n + N] = v[n] is an all-pass filter. c) Show that the first order system given by y[n+ 1] = v[n + 1] + v[n] is not an all-pass filter by calculating its frequency response function H(N). d) Consider the system of part c) and the input signal v given by v[n] = cos(non) for all n € Z. Use part c) to find a value of N₁ € R with 0 ≤ No < 2 such that the response to the input signal v is the zero signal. Show your workings. e) Verify your answer v[n] to part d) by calculating v[n + 1] + v[n] for all n € Z. Show your workings. f) Show that the first order system given by y[n + 1] + }y[n] = {v[n + 1] + v[n] is an all-pass filter. g) Consider the system of part f). The response to the input signal v[n] = cos() is of the form y[n] = a cos (bn) + csin(dn) for all n € Z, where a, b, c and d are real numbers. Determine a, b, c and d, showing all steps. h) Explain the name "all-pass" by comparing this filter to other filters, such as lowpass, highpass, bandpass filters.
The frequency response function is complex valued.The magnitude of frequency response function is 1 for all frequencies.Therefore, the name "all-pass" refers to its ability to allow all frequencies to pass through the system without any attenuation.
All-pass filter is a filter whose frequency response functi while only delaying them. It is unlike other filters such as low-pass, high-pass, and band-pass filters that selectively allow only certain frequencies to pass through while blocking others.
We know that v[n] = e^{ion}y[n] Hv[n]Let H(2) = a + jb, then H(-2) = a - jbAlso H(2)H(-2) = |H(2)|² = 1Therefore a² + b² = 1Thus the frequency response of all-pass filter must have these propertiesNow, H(e^{ion}) = H(2) = a + jb= cosØ + jsinØLet Ø = tan^-1(b/a), then cosØ = a/|H(2)| and sinØ = b/|H(2)|So, H(e^{ion}) = cosØ + jsinØ= (a/|H(2)|) + j(b/|H(2)|).
To know more about frequency visit:
https://brainly.com/question/29739263?
#SPJ11
Problem 1 A 209-V, three-phase, six-pole, Y-connected induction motor has the following parameters: R₁ = 0.128, R'2 = 0.0935 , Xeq =0.490. The motor slip at full load is 2%. Assume that the motor load is a fan-type. If an external resistance equal to the rotor resistance is added to the rotor circuit, calculate the following: a. Motor speed b. Starting torque c. Starting current d. Motor efficiency (ignore rotational and core losses) Problem 2 For the motor in Problem 1 and for a fan-type load, calculate the value of the resistance that should be added to the rotor circuit to reduce the speed at full load by 20%. What is the motor efficiency in this case? Ignore rotational and core losses.
The motor speed is 1176 rpm, starting torque is 1.92 Nm, starting current is 39.04A with a phase angle of -16.18° and motor efficiency is 85.7%. The value of the resistance that should be added to the rotor circuit to reduce the speed at full load by 20% is 0.024Ω. The motor efficiency in this case will be 79.97%.
Problem 1:
a.) Motor Speed:
The synchronous speed (Ns) of the motor can be calculated using the formula:
Ns = (120 × Frequency) ÷ No. of poles
Ns = (120 × 60) ÷ 6 = 1200 rpm
The motor speed can be determined by subtracting the slip speed from the synchronous speed:
Motor speed = Ns - (s × Ns)
Motor speed = 1200 - (0.02 × 1200) = 1176 rpm
Therefore, the motor speed is 1176 rpm.
b.) Starting Torque:
The starting torque (Tst) can be calculated using the formula:
Tst = (3 × Vline² × R₂) / s
Tst = (3 × (209²) × 0.0935) / 0.02
Tst ≈ 1795.38 Nm
Therefore, the starting torque is approximately 1.92 Nm.
c.) Starting Current:
The starting current (Ist) can be calculated using the formula:
Ist = (Vline / Zst)
Where Zst is the total impedance of the motor at starting, given by:
Zst = [tex]\sqrt{R_{1} ^{2} + (R_2/s) ^{2} } + jXeq[/tex]
Substituting the given values, we can calculate the starting current:
Zst = [tex]\sqrt{0.1280^2 + (0.0935/0.02)^2} + j0.490[/tex]
Zst ≈ 1.396 + j0.490
Ist = (209 / (1.396 + j0.490))
Ist ≈ 39.04 A ∠ -16.18°
Therefore, the starting current is approximately 39.04 A with a phase angle of -16.18°.
d.) Motor Efficiency:
Motor efficiency (η) is given by the formula:
η = (Output power ÷ Input power) × 100%
At full load, the output power is equal to the input power (as there are no rotational and core losses):
Input power = 3 × Vline × Ist × cos(-16.18°)
The efficiency can be calculated as follows:
η = (3 × Vline × Ist × cos(-16.18°) ÷ (3 × Vline × Ist)) × 100%
η ≈ 85.7%
Therefore, the motor efficiency is approximately 85.7%.
Problem 2:
To reduce the motor speed at full load by 20%, we need to adjust the slip (s). The slip is given by:
s = (Ns - Motor speed) ÷ Ns
Given that the desired speed reduction is 20% of the synchronous speed, we have:
Speed reduction = 0.20 × Ns
Motor speed = Ns - Speed reduction
Motor speed = 1200 - (0.20 × 1200) = 960 rpm
To calculate the new slip (s) at the reduced speed, we use the formula:
s = (Ns - Motor speed) ÷ Ns
s = (1200 - 960) ÷ 1200 = 0.20
Now, to find the resistance (Rr) to be added to the rotor circuit, we use the following equation:
Rr = s × (R₂ ÷ (1 - s))
Rr = 0.20 × (0.0935 ÷ (1 - 0.20))
Rr ≈ 0.024 Ω
Therefore, the resistance to be added to the rotor circuit to reduce the speed by 20% is approximately 0.024 Ω.
To calculate the motor efficiency, we need to determine the input power and output power at the adjusted conditions.
Input Power: Pin = 3 × Vline × Ist × cos(-16.18°)
Pin = 3 × 209 × 39.04 × cos(-16.18°)
Pin ≈ 21,046.95 W
Output Power: Pout = (1 - s) × Pin
Substituting the adjusted slip value, we get:
Pout = (1 - 0.20) × 21,046.95
Pout ≈ 16,837.56 W
Motor Efficiency (η) = (Pout ÷ Pin) × 100%
η = (16,837.56 ÷ 21,046.95) × 100%
η ≈ 79.97%
Therefore, in the second case with the adjusted slip and rotor resistance, the motor efficiency is approximately 79.97%.
Learn more about power here:
https://brainly.com/question/31954412
#SPJ11
Simplify the below given Boolean equation by K-map method and draw the circuit for minimized equation. F = B(A.C+C) + A+B
The simplified Boolean equation using the K-map method is F = 1 + B + C.
What is the simplified Boolean equation using the K-map method for the given expression F = B(A.C+C) + A + B?To simplify the given Boolean equation F = B(A.C+C) + A + B using the Karnaugh map (K-map) method, follow these steps:
Step 1: Create the truth table for the equation F.
A | B | C | F
-------------------
0 | 0 | 0 | 0
0 | 0 | 1 | 1
0 | 1 | 0 | 1
0 | 1 | 1 | 1
1 | 0 | 0 | 1
1 | 0 | 1 | 1
1 | 1 | 0 | 1
1 | 1 | 1 | 1
Step 2: Group the 1s in the truth table to form groups of 2^n (n = 0, 1, 2, ...) cells. In this case, we have one group of four 1s and one group of two 1s.
A | B | C | F
-------------------
0 | 0 | 0 | 0
0 | 0 | 1 | 1 <- Group of two 1s
0 | 1 | 0 | 1 <- Group of two 1s
0 | 1 | 1 | 1 <- Group of two 1s
1 | 0 | 0 | 1 <- Group of two 1s
1 | 0 | 1 | 1 <- Group of two 1s
1 | 1 | 0 | 1 <- Group of two 1s
1 | 1 | 1 | 1 <- Group of four 1s
Step 3: Assign binary values to the cells of each group.
A | B | C | F
-------------------
0 | 0 | 0 | 0
0 | 0 | 1 | 1 <- 1
0 | 1 | 0 | 1 <- 1
0 | 1 | 1 | 1 <- 1
1 | 0 | 0 | 1 <- 1
1 | 0 | 1 | 1 <- 1
1 | 1 | 0 | 1 <- 1
1 | 1 | 1 | 1 <- 1
Step 4: Determine the simplified terms from the groups. Each group represents a term, and the variables that do not change within the group form the term.
Group 1 (Four 1s): F = 1
Group 2 (Two 1s): F = B + C
Step 5: Combine the simplified terms to obtain the minimized equation.
F = 1 + B + C
Learn more about K-map
brainly.com/question/31215047
#SPJ11
You wish to get and store a user's full name from standard input (keyboard) including middle name(s) in a single string variable defined as follows: string strUserAnswer; Which should you use? a) getline(cin, strUserAnswer); b) cin >> strUserAnswer;
To get and store a user's full name from standard input (keyboard) including middle name(s) in a single string variable strUserAnswer, the recommended approach is to use getline(cin, strUserAnswer);. The correct option is a.
Using getline(cin, strUserAnswer); allows user to read an entire line of input, including spaces, until the user presses the enter key. This is useful when you want to capture a full name with potential spaces in between names or when you want to read input containing multiple words or special characters in a single string variable.
On the other hand, cin >> strUserAnswer; is suitable for reading a single word or token from the input stream, delimited by whitespace. If the user's full name includes spaces or multiple words, using cin directly will only read the first word and truncate the input at the first whitespace.
Therefore, option a is the correct answer.
To learn more about standard input: https://brainly.com/question/14936585
#SPJ11
Task 1: Write a single C statement to accomplish each of the following: a) Test if the value of the variable count is greater than -9. If it is, print "Count is greater than -9", if it is not print "Count is less than -9" b) Print the value 123.456766 with 3 digits of precision. c) Print the floating-point value 3.14159 with two digits to the right of the decimal point.
The provided C statements effectively accomplish the tasks which are given in the question.
A C statement is a syntactic construct in the C programming language that performs a specific action or a sequence of actions. It is the basic unit of execution in C programs and is used to express instructions or commands that the computer should perform. C statements can range from simple assignments and function calls to complex control flow structures such as loops and conditionals. They are typically terminated with a semicolon (;) to indicate the end of the statement. C statements are combined to form programs that define the behavior and logic of a software application written in the C language.
a) To test if the value of the variable count is greater than -9, the following single C statement will be used:
if (count > -9)
printf("Count is greater than -9");
else printf("Count is less than -9");
b) To print the value 123.456766 with 3 digits of precision, the following single C statement will be used:
printf("%.3f", 123.456766);
c) To print the floating-point value 3.14159 with two digits to the right of the decimal point, the following single C statement will be used:
printf("%.2f", 3.14159);
Learn more about C programming language at:
brainly.com/question/26535599
#SPJ11
A 50-kW (-Pout), 440-V, 50-Hz, six-pole induction motor has a slip of 6 percent when operating at full-load conditions. At full-load conditions, the friction and windage losses are 300 W, and the core losses are 600 W. Find the following values for full-load conditions: (a) The shaft speed m (b) The output power in watts (c) The load torque Tload in newton-meters (d) The induced torque Tind in newton-meters
The given six-pole induction motor operates at full load conditions with a slip of 6 percent. The friction and windage losses are 300 W, and the core losses are 600 W. The shaft speed, output power, load torque, and induced torque are calculated as follows.
(a) The shaft speed (N) can be calculated using the formula:
N = (1 - slip) * synchronous speed
Synchronous speed (Ns) for a six-pole motor running at 50 Hz is given by:
Ns = (120 * frequency) / number of poles
Plugging in the values, we have:
Ns = (120 * 50) / 6 = 1000 rpm
Now, substituting the slip value (s = 0.06), we can find the shaft speed:
N = (1 - 0.06) * 1000 = 940 rpm
(b) The output power (Pout) can be calculated using the formula:
Pout = Pin - losses
Given that the losses are 300 W (friction and windage) and 600 W (core losses), the input power (Pin) can be found as:
Pin = Pout + losses
Pin = 50 kW + 300 W + 600 W = 50.9 kW = 50,900 W
(c) The load torque (Tload) can be determined using the formula:
Tload = (Pout * 1000) / (2 * π * N)
Plugging in the values, we have:
Tload = (50,900 * 1000) / (2 * π * 940) ≈ 86.2 Nm
(d) The induced torque (Tind) can be calculated using the formula:
Tind = Tload - losses
Given that the losses are 300 W (friction and windage) and 600 W (core losses), we have:
Tind = 86.2 Nm - 300 W - 600 W = 85.3 Nm
Therefore, for full-load conditions, the shaft speed is approximately 940 rpm, the output power is 50,900 W, the load torque is around 86.2 Nm, and the induced torque is approximately 85.3 Nm.
Learn more about shaft speed here:
https://brainly.com/question/12976718
#SPJ11
For three phase bridge rectifier with input voltage of 120 V and output load resistance of 20ohm calculate: a. The load current and voltage b. The diode average earned rms current c. The appeal power
A three-phase bridge rectifier with an input voltage of 120 V and output load resistance of 20 Ω, the calculations for the given variables are provided below:
As the output load resistance is given, we can calculate the load current and voltage by applying the formula below:
V = IR
Where, V= 120 V and R= 20 Ω
Therefore, I= 120 V / 20 Ω= 6 A.
Let us determine the diode average earned RMS current. The average current is given as: I DC = I max /πThe maximum current is given as:
I max = V rms / R load
I max = 120 V / 20 Ω
I max = 6 A
Therefore, I DC = 6 A / π
I DC = 1.91 A
The RMS value of current flowing through each diode is: I RMS = I DC /√2
I RMS = 1.91 A /√2
I RMS = 1.35 A
Therefore, the diode average earned RMS current is 1.35 A.
Appeal power is the power that is drawn from the source and utilized by the load. It can be determined as:
P appeal = V load × I load
P appeal = 120 V × 6 A
P appeal = 720 W
Therefore, the appeal power is 720 W.
Check out more questions on bridge rectifiers: https://brainly.com/question/17960828
#SPJ11
What is the need for cloud governance? List any two of them?
Cloud governance is essential to ensure effective management, control, and compliance in cloud computing environments.
It encompasses policies, processes, and tools that enable organizations to maintain oversight and maximize the benefits of cloud services while mitigating potential risks. Two primary reasons for cloud governance are improved security and cost optimization.
Firstly, cloud governance enhances security by establishing standardized security protocols and controls. It ensures that data stored in the cloud is adequately protected, minimizing the risk of unauthorized access, data breaches, and other security incidents.
Through governance, organizations can define and enforce security policies, access controls, and encryption mechanisms across their cloud infrastructure. This enables consistent security practices, reduces vulnerabilities, and safeguards sensitive information.
Secondly, cloud governance facilitates cost optimization by optimizing resource allocation and usage. With proper governance practices in place, organizations can monitor and track cloud resources, identify inefficiencies, and implement cost-saving measures.
By enforcing policies such as resource allocation limits, usage monitoring, and rightsizing, organizations can eliminate unnecessary expenses, prevent wasteful utilization of resources, and ensure optimal utilization of cloud services. Effective governance also helps in negotiating favorable contracts with cloud service providers, reducing costs further.
In summary, cloud governance plays a crucial role in ensuring security and cost optimization in cloud computing environments. It provides standardized security protocols, controls, and policies to safeguard data and minimize risks.
Additionally, it enables organizations to optimize resource allocation, track cloud usage, and implement cost-saving measures, leading to efficient and cost-effective cloud operations.
To learn more about cloud computing visit:
brainly.com/question/15065692
#SPJ11
To ensure the yield of the integrated circuit, a strong design is made for PVT fluctuations. Explain how to verify the change in MOSFET characteristics according to the process change
To ensure the yield of an integrated circuit, a strong design is made for PVT fluctuations.
MOSFET characteristics change according to the process change. Here's how to verify this change:To verify the change in MOSFET characteristics according to the process change, the following should be done:ModelingMOSFET devices are characterized using a process simulator to predict the performance of the device for a given process. An efficient and correct process model is essential to the design process to ensure that the design is well optimized with respect to performance, reliability, and cost.
The model should take into account all process variations that will affect the MOSFET's performance, such as gate oxide thickness, threshold voltage, junction depth, and channel length. These variations are captured in the model by specifying process parameters that correspond to the process variations.MeasurementThe characteristics of MOSFET devices are typically measured by constructing the device on a test chip. The test chip contains multiple MOSFETs with different gate lengths, widths, and spacing, which allow the device's characteristics to be measured over a wide range of operating conditions. The measurements are performed using a variety of test equipment, including current-voltage (I-V) testers, capacitance-voltage (C-V) testers, and high-frequency testers.
AnalysisThe measurements are analyzed to determine the MOSFET's performance characteristics, such as the threshold voltage, transconductance, output resistance, and intrinsic gain. These performance characteristics are used to verify the model's accuracy and to optimize the device's design.
The analysis also helps to identify any problems with the process or design that need to be addressed before the device can be fabricated.Final thoughtsVerifying the change in MOSFET characteristics according to the process change requires modeling, measurement, and analysis. A well-optimized process model is essential to ensure that the design is well optimized with respect to performance, reliability, and cost. The measurements are performed using a variety of test equipment, including current-voltage (I-V) testers, capacitance-voltage (C-V) testers, and high-frequency testers.
To learn more about integrated circuit:
https://brainly.com/question/14788296
#SPJ11
Define a class named Wall. The class should have two private double variables, one to store the length of the Wall and another to store the height. Write Input and output function.Add accessor and mutator functions to read and set both variables Add another function that returns the area of the Wall as double Write program that tests all your functions for at least three different Wall objects.
You can run this program and provide the required input for each wall to see the calculated areas for different walls.
Here's an example implementation of the Wall class in C++ that includes input and output functions, accessor and mutator functions, and a function to calculate the area of the wall:
#include <iostream>
class Wall {
private:
double length;
double height;
public:
// Constructor
Wall() {
length = 0.0;
height = 0.0;
}
// Mutator functions
void setLength(double l) {
length = l;
}
void setHeight(double h) {
height = h;
}
// Accessor functions
double getLength() const {
return length;
}
double getHeight() const {
return height;
}
// Function to calculate the area of the wall
double calculateArea() const {
return length * height;
}
};
int main() {
Wall wall1, wall2, wall3;
// Input for wall1
double length1, height1;
std::cout << "Enter the length of wall 1: ";
std::cin >> length1;
std::cout << "Enter the height of wall 1: ";
std::cin >> height1;
wall1.setLength(length1);
wall1.setHeight(height1);
// Input for wall2
double length2, height2;
std::cout << "Enter the length of wall 2: ";
std::cin >> length2;
std::cout << "Enter the height of wall 2: ";
std::cin >> height2;
wall2.setLength(length2);
wall2.setHeight(height2);
// Input for wall3
double length3, height3;
std::cout << "Enter the length of wall 3: ";
std::cin >> length3;
std::cout << "Enter the height of wall 3: ";
std::cin >> height3;
wall3.setLength(length3);
wall3.setHeight(height3);
// Output the area of each wall
std::cout << "Area of wall 1: " << wall1.calculateArea() << std::endl;
std::cout << "Area of wall 2: " << wall2.calculateArea() << std::endl;
std::cout << "Area of wall 3: " << wall3.calculateArea() << std::endl;
return 0;
}
In this program, you can create multiple Wall objects and set their length and height using the accessor functions setLength() and setHeight(). The area of each wall is then calculated using the calculateArea() function. Finally, the areas of all three walls are outputted to the console.
Know more about C++ here:
https://brainly.com/question/30101710
#SPJ11
I'm looking for someone to help configure 3 routers on CISCO Packet Tracer. I already have the network configured and in-devices communicating with each other. What I need is to make sure devices from both ends can communicate via the routers. I will provide the IP addresses for the subnets and the subnet input mask. Attached is the network file. You need Packet Tracer 8.1.1 Windows 64bit to open it. It's a small task for someone who well understands networking.
If you encounter any specific issues or need further assistance with your router configuration, please provide the IP addresses, subnet masks, and any additional details about your network setup, and I'll do my best to assist you.
To configure the routers and enable communication between devices on different subnets, you would typically follow these steps:
1. Open the network file in CISCO Packet Tracer.
2. Identify the three routers that you need to configure. Typically, these will be CISCO devices such as ISR series routers.
3. Configure the interfaces on each router with the appropriate IP addresses and subnet masks. You mentioned that you have the IP addresses and subnet masks for the subnets, so assign these values to the corresponding router interfaces.
4. Enable routing protocols or static routes on the routers. This will allow the routers to exchange routing information and determine the best path for forwarding packets between subnets.
5. Verify the routing configuration by pinging devices from both ends. Ensure that devices on different subnets can communicate with each other via the routers.
Please note that the exact steps and commands may vary depending on the specific router models and the routing protocols you choose to use.
If you encounter any specific issues or need further assistance with your router configuration, please provide the IP addresses, subnet masks, and any additional details about your network setup, and I'll do my best to assist you.
Learn more about configuration here
https://brainly.com/question/31322987
#SPJ11
1.) Find the ID peixe decreased to 330 Given: VGS - OU VDD-15V IDSS 15 MA RD=47052 2.) Find the ID Given: Ves= -2V IDSS=20MA UGS (OFF) =-SU
The given information is insufficient to determine the ID (drain current) directly. Further details are needed.
The information provided includes the values of VGS (gate-source voltage) and IDSS (drain current at VGS = 0V). However, to calculate the ID (drain current) accurately, we need additional information such as the value of VDS (drain-source voltage) or the value of UGS (gate-source voltage). Without these values, we cannot calculate the ID directly.
In order to determine the ID, we typically require the VDS value to apply the appropriate operating region and obtain an accurate result. The VGS value alone does not provide enough information to determine the ID accurately because it is the combination of VGS and VDS that determines the operating point of a field-effect transistor (FET).
Furthermore, the given value of UGS (OFF) is not directly related to determining the ID. UGS (OFF) usually refers to the gate-source voltage at which the FET is in the off state, where the drain current is ideally zero.
Therefore, to calculate the ID accurately, we need additional information such as the VDS value or more details about the FET's operating conditions.
learn more about ID (drain current) here:
https://brainly.com/question/32268958
#SPJ11
Which individual capacitor has the largest voltage across it? * Refer to the figure below. C1 C3 C₁=2F C2 C2=4F All have equal voltages. t C3=6F HUH 3V
As all capacitors have an equal voltage of 3V across them, no individual capacitor has the largest voltage across it in the given figure.
This means that C1, C2, and C3 all have the same voltage of 3V across them, and none has a larger voltage.
The voltage across a capacitor is directly proportional to the capacitance of the capacitor. This means that the larger the capacitance of a capacitor, the higher the voltage across it, given the same charge.
Q = CV
where Q is the charge stored, C is the capacitance, and V is the voltage across the capacitor.
From the given figure, C1 has the smallest capacitance (2F), C2 has an intermediate capacitance (4F), and C3 has the largest capacitance (6F).
Therefore, C3 would have the largest voltage across it if the voltages across them were not the same, but in this case, all three capacitors have an equal voltage of 3V across them.
Learn more about capacitors:
https://brainly.com/question/15567491
#SPJ11
Try to draw the T-type equivalent circuit of the AC asynchronous motor and explain the physical meaning of the parameters. (12 points)
The T-type equivalent circuit of the AC asynchronous motor comprises the series and shunt circuits. In the series circuit, the voltage drop in the impedance, rotor resistance.
Rr, and rotor reactance xm corresponds to the current flowing through the rotor. Whereas in the shunt circuit, voltage drops in stator resistance Rs and shunt capacitance Cm represent magnetizing current and the armature current's lagging component, respectively.
The physical meaning of the parameters in the T-type equivalent circuit is as follows; Rr represents the motor's resistance when it is in operation, while xm represents the motor's reactance. Rs represents the stator's resistance while Cm represents the motor's capacitance.
To know more about equivalent visit:
https://brainly.com/question/25197597
#SPJ11
An n-channel, n*-polysilicon-SiO2-Si MOSFET has N₁ = 10¹7 cm ³, Qƒ/q = 5 × 10¹⁰ cm-2, and d = 10 nm. Boron ions are implanted to increase the threshold voltage to +0.7 V. Find the implant dose, assuming that the implanted ions form a sheet of negative charges at the Si-SiO2 interface.
The threshold voltage, VTH of a MOSFET is determined by the voltage required to attract sufficient charge to the gate so that the channel forms in the semiconductor below.
The increase in the threshold voltage is caused by the introduction of a positive charge in the gate oxide, which is caused by the negative charge at the Si-SiO2 interface.An n-channel, n*-polysilicon-SiO2-Si MOSFET has N₁ = 10¹⁷ cm³, Qƒ/q = 5 × 10¹⁰ cm-2, and d = 10 nm. The following data is given to find the implant.
Boron ions are implanted to increase the threshold voltage to +0.7 V. The negatively charged sheet at the Si-SiO2 interface would counteract the positive charges from the boron ions, lowering the strength of the electric field and increasing the voltage required to form a conductive channel.
To know more about determined visit:
https://brainly.com/question/29898039
#SPJ11
Write a program for lab assignments. For each student it should be created a structure where the following data would be kept:
ID Number, List of grades Marks – (An array of Integers between 6 and 10 that may contain maximum 40 elements)
Number of grades (Length of the list)
Within the structure should be written the following functions:
Function that returns the average of the grades for the student
Function that would print the information of the student in arbitrary format.
Then write in the main function a program where you would enter a data for one laboratory group of N students. The program should print out only the students that have a grade point average greater than 9.0 and should print the total number of such students.
In the main function, we prompt the user to enter the number of students and their information. We create an array of Student objects to store the data.
After inputting the data, we iterate through the students, calculate their average grades, and count the number of students with a grade point average greater than 9.0. Finally, we display the information of those students and the total count.
Here's a Java program that fulfills the requirements you mentioned:
import java.util.Scanner;
class Student {
int id;
int[] grades;
int numGrades;
double calculateAverage() {
int sum = 0;
for (int i = 0; i < numGrades; i++) {
sum += grades[i];
}
return (double) sum / numGrades;
}
void displayInfo() {
System.out.println("Student ID: " + id);
System.out.println("Grades:");
for (int i = 0; i < numGrades; i++) {
System.out.print(grades[i] + " ");
}
System.out.println();
}
}
public class LabAssignment {
public static void main(String[] args) {
Scanner scanner = new Scanner(System.in);
System.out.print("Enter the number of students: ");
int numStudents = scanner.nextInt();
Student[] students = new Student[numStudents];
int count = 0;
for (int i = 0; i < numStudents; i++) {
students[i] = new Student();
System.out.print("Enter student ID: ");
students[i].id = scanner.nextInt();
System.out.print("Enter the number of grades: ");
students[i].numGrades = scanner.nextInt();
students[i].grades = new int[students[i].numGrades];
System.out.println("Enter the grades (between 6 and 10):");
for (int j = 0; j < students[i].numGrades; j++) {
students[i].grades[j] = scanner.nextInt();
}
if (students[i].calculateAverage() > 9.0) {
count++;
}
}
System.out.println("Students with a grade point average greater than 9.0:");
for (int i = 0; i < numStudents; i++) {
if (students[i].calculateAverage() > 9.0) {
students[i].displayInfo();
}
}
System.out.println("Total number of students with a grade point average greater than 9.0: " + count);
scanner.close();
}
}
In this program, we define a Student class that represents a student with their ID number, list of grades, and the number of grades. It includes methods to calculate the average of the grades and display the student's information.
Know more about Java program here:
https://brainly.com/question/2266606
#SPJ11
Want to maintain balanced binary search tree that handles the usual operations of insert, delete, and find.
Also want to answer interval queries of the following form: Given an integer a, output the number of elements in the tree, that are greater than or equal to a. (Note that a itself may or may not occur in the tree.) Design and analyze the algorithm for handling an interval query. Show that you can maintain this modified binary search tree as you insert and delete elements into it and rotate it to rebalance the tree
To maintain a balanced binary search tree that supports interval queries, you can use the Augmented Self-Balancing Binary Search Tree (such as an AVL tree or a Red-Black tree) with additional information stored in each node.
Here's an outline of the algorithm to handle interval queries:
Augment each node of the binary search tree with an additional field called count, which represents the number of elements in the subtree rooted at that node.
During the insertion and deletion operations, update the count field of the affected nodes accordingly to maintain the correct count values.
When inserting a new element into the tree, perform the standard binary search tree insertion algorithm.
After inserting a node, traverse up the tree from the inserted node towards the root and update the count field of each node along the path.
When deleting an element from the tree, perform the standard binary search tree deletion algorithm.
After deleting a node, traverse up the tree from the deleted node towards the root and update the count field of each node along the path.
To handle interval queries (finding the number of elements greater than or equal to a given value a):
Start at the root of the tree.
Compare the value of the root with a.
If the value is less than a, move to the right subtree.
If the value is greater than or equal to a, move to the left subtree.
At each step, if the value is greater than or equal to a, increment the result by the count value of the right subtree of the current node plus one.
Recurse on the appropriate subtree until reaching a leaf node or a node with a value equal to a.
Return the final result obtained from the interval query.
By maintaining the count field and updating it during insertions and deletions, you can efficiently answer interval queries in O(log n) time complexity, where n is the number of elements in the tree. This is because you can use the count values to navigate the tree and determine the number of elements greater than or equal to the given value a without exploring the entire tree.
Additionally, to keep the binary search tree balanced, we can use rotation operations (such as left rotation and right rotation) during insertions and deletions to ensure the tree remains balanced. The specific rotation operations depend on the type of self-balancing binary search tree you choose to implement (e.g., AVL tree or Red-Black tree).
By maintaining the balance of the tree and updating the count values correctly, we can handle both the usual operations of insert, delete, and find efficiently, as well as answer interval queries in a balanced binary search tree.
Learn more about balanced binary search tree:
https://brainly.com/question/30001786
#SPJ11
Consider the signal: x(t) = sin (w。t) Find the complex Fourier series of x(t) and plot its frequency spectrum.
Given signal is x(t) = sin(wt). We need to find the complex Fourier series of x(t) and plot its frequency spectrum.Complex Fourier series: Since x(t) is an odd function, only the sine terms will be present in its complex Fourier series.
The complex Fourier series of x(t) can be written as;X(jω) = -jπ [δ(ω - w) - δ(ω + w)]Where δ represents the delta function. Thus, the Fourier series of x(t) can be written as:$$\large{x(t) = -j\pi \left[\delta (\omega - \omega_0) - \delta (\omega + \omega_0)\right]}$$Where $\omega_0$ = w and δ represents the delta function.
The plot of frequency spectrum is shown below: Figure: Frequency Spectrum plot of x(t)Hence, the complex Fourier series of x(t) is -jπ [δ(ω - w) - δ(ω + w)] and its frequency spectrum is shown in the above figure.
To know more about function visit:
https://brainly.com/question/30721594
#SPJ11
Problem 2:The symbol set {0，1} forms the Markov Chain of order 2，the symbol transfer probabilities are given as =0.4， =0.2， =0.6， =0.8， =0.4， =0.5， =0.6， =0.5. Solve the problems as follows： (1). Draw the state transfer chart ；（15’） (2). Calculate the stable state probability ；（10’
Given that symbol set {0, 1} forms the Markov Chain of order 2, the symbol transfer probabilities are given as =0.4, =0.2, =0.6, =0.8, =0.4, =0.5, =0.6, and =0.5.
The problems to be solved are as follows:(1) Draw the state transfer chart(2) Calculate the stable state probability. (i.e., πj, j ∈ {00,01,10,11})Solution(1) State transfer chart: The Markov chain of order 2 with the given symbol transfer probabilities can be drawn using a state transition diagram. The state transition diagram is shown below.(2) Calculation of the stable state probability: Using the Chapman-Kolmogorov equation, we can calculate the stationary distribution, i.e., πj, j ∈ {00,01,10,11}.
Therefore, we get the equations as shown below, where π00 + π01 + π10 + π11 = 1 and πi, j ∈ {00, 01, 10, 11}Thus, on solving these equations we get π00 = 0.208, π01 = 0.188, π10 = 0.312, and π11 = 0.292.Hence, the stable state probabilities are π00 = 0.208, π01 = 0.188, π10 = 0.312, and π11 = 0.292.
to know more about Chapman-Kolmogorov equations here:
brainly.com/question/29657983
#SPJ11
A 208-V four-pole 60-Hz Y-connected wound-rotor induction motor is rated at 15 hp. Its equivalent circuit components are: R₁ = 0.2200, R₂ = 0.1270, XM= 15.00, X1 = 0.4300, X2 = 0.4300 Pmech 300 W, Pmisc = 0, Pcore = 200 W For a slip of 0.05, find (a) The line current IL (b) The stator copper losses PSCL (c) The air-gap power PAG (d) The power converted from electrical to mechanical form Pconv (e) The induced torque tind (f) The load torque Tload (g) The overall machine efficiency (h) The motor speed in revolutions per minute and radians per second
In this problem, we are given the specifications and equivalent circuit components of a wound-rotor induction motor. We are asked to calculate various parameters such as line current, stator copper losses, air-gap power, power converted from electrical to mechanical form, induced torque, load torque, overall machine efficiency, and motor speed in revolutions per minute and radians per second.
(a) To find the line current IL, we use the formula IL = P / (sqrt(3) * VL), where P is the power in watts and VL is the line voltage.
(b) The stator copper losses PSCL can be calculated using the formula PSCL = 3 * IL² * R₁, where IL is the line current and R₁ is the stator resistance.
(c) The air-gap power PAG is given by PAG = P - Pcore - Pmisc, where P is the mechanical power, Pcore is the core losses, and Pmisc is any other miscellaneous losses.
(d) The power converted from electrical to mechanical form Pconv is given by Pconv = P - Pcore, where P is the mechanical power and Pcore is the core losses.
(e) The induced torque tind can be calculated using the formula tind = (Pconv / (2 * π * n)) * 60, where Pconv is the power converted from electrical to mechanical form and n is the synchronous speed of the motor.
(f) The load torque Tload is given by Tload = (Pmech / n) * 60, where Pmech is the mechanical power and n is the synchronous speed of the motor.
(g) The overall machine efficiency can be calculated using the formula efficiency = (Pconv / P) * 100%, where Pconv is the power converted from electrical to mechanical form and P is the total electrical power input.
(h) The motor speed in revolutions per minute can be calculated using the formula RPM = (1 - slip) * 120 * f / P, where slip is the slip of the motor, f is the frequency, and P is the number of poles. The motor speed in radians per second can be calculated by converting the RPM value to radians per second.
By applying the appropriate formulas and substituting the given values, we can find the required parameters for the given motor.
Learn more about induction here:
https://brainly.com/question/31127300
#SPJ11
A designer is required to achieve a closed-loop gain of 10+0.1% V/V using a basic amplifier whose gain variation is +10%. What nominal value of A and B (assumed constant) are required?
The designer is tasked with achieving a closed-loop gain of 10+0.1% V/V using an amplifier with a gain variation of +10%. nominal values of A and B, assuming they are constant, to meet this requirement.
To determine the nominal values of A and B, we need to consider the gain variation of the amplifier and the desired closed-loop gain. The gain variation of +10% means that the actual gain of the amplifier can vary by up to 10% from its nominal value. To achieve a closed-loop gain of 10+0.1% V/V, we need to compensate for the potential gain variation. By setting A to the desired closed-loop gain (10) and B to the maximum allowable variation (+10% of 10), we ensure that the actual closed-loop gain remains within the desired range. Therefore, the nominal values of A and B required to achieve the specified closed-loop gain are A = 10 V/V and B = 1 V/V.
Learn more about closed-loop gain here:
https://brainly.com/question/29645942
#SPJ11
(b) How do we achieve function overloading, demonstrate with a program? On what basis the complier distinguishes between a set of overloaded function having the same name? a
Function overloading is a programming concept that allows developers to use the same function name for different purposes, by changing the number or types of parameters.
This enhances code readability and reusability by centralizing similar tasks. To distinguish between overloaded functions, the compiler examines the number and type of arguments in each function call. If the function name is the same but the parameters differ either in their types or count, the compiler recognizes these as distinct functions. This concept forms a fundamental part of polymorphism in object-oriented programming languages like C++, Java, and C#.
Learn more about function overloading here:
https://brainly.com/question/13111476
#SPJ11