what kind of warehouse is created to serve customers whether they order in bulk quantities, like full-pallet quantities, or individual items for household delivery?
-All-purpose warehouse -mnipotent warehouse -mni-shore warehouse -mni-channel warehouse Versatile warehouse

Every A/C system has all of the following except heater core

An A/C (air conditioning) system is designed to cool and dehumidify the air inside a vehicle or a building.

It typically includes several components such as a compressor, condenser, evaporator, expansion valve, and a refrigerant.

Heater core is typically not a component found in an A/C (air conditioning) system.

A heater core is part of a vehicle's heating system, which works independently from the A/C system.

Therefore, the correct answer is Heater core.

Read more about ac system at

https://brainly.com/question/14116053

#SPJ1

No, the physical address 346E0 cannot be the starting address for a segment. This is because the starting address of a segment must be aligned with the segment's size or boundary, which is determined by the processor's architecture.

Segment boundaries are defined by 16-byte or 4-byte boundaries, depending on the segment's use. Therefore, the starting address of a segment must be a multiple of 16 or 4, respectively, depending on the segment type.

In the given address 346E0, the last digit is 0, which indicates that it is a multiple of 16. However, we do not have enough information about the processor architecture and segment size to determine whether this is an appropriate starting address for a segment.

In general, when defining a segment, it is important to ensure that the starting address is properly aligned with the segment's boundary to avoid any issues with memory access and processing.

Learn more about segment boundaries here : brainly.com/question/30000398

#SPJ1

Answer:

In the first stage of the experiment where Min is focusing only on the physical properties of water and lemonade, he would not use any comparison point that relates to the taste or flavor of the two liquids. Taste and flavor are not physical properties and would require a different set of tests and observations to determine. Therefore, in the first stage of the experiment, Min would focus on physical properties such as color, density, boiling point, freezing point, viscosity, surface tension, and any other physical property that can be observed or measured without consuming the liquids or using taste buds.

In case of a failure of both hydraulic system 2 and 3, accumulators in both systems provide pressure for a minimum of two brake applications. In the B777 hydraulic system, the three hydraulic systems are designated as system 1, system 2, and system 3. The hydraulic system has three types of accumulators, which are used to store energy, absorb hydraulic shocks, or compensate for fluid loss.

For such more question on accumulators

https://brainly.com/question/13152930

#SPJ11

The peak voltage of a sine wave is calculated as the RMS voltage multiplied by the square root of 2. Therefore, the peak voltage of a 240 VRMS sine wave is approximately 340 volts. So, your answer is option 2, 340v.

The RMS voltage (VRMS) of a sine wave is the "root-mean-square" average value of the waveform. It is calculated by taking the square root of the mean of the squares of the instantaneous voltage values over one cycle of the waveform.

For a sine wave, the peak voltage (Vp) is the highest voltage value that the waveform reaches, and it occurs at 90 degrees or pi/2 radians (a quarter cycle) after the zero crossing.

The relationship between VRMS and Vp for a sine wave is given by the formula:

Vp = VRMS x sqrt(2)

This formula shows that the peak voltage of a sine wave is equal to the RMS voltage multiplied by the square root of 2.

Therefore, in the case of a 240 VRMS sine wave, the peak voltage would be:

Vp = VRMS x sqrt(2) = 240 x 1.414 = 339.36 volts

Rounding this to the nearest whole number, we get the answer of 340 volts, which is option 2.

Learn more about peak voltage at:

https://brainly.com/question/24334542?

#SPJ1

Answer:

Explanation:

Using a machine learning algorithm, Aerosolve’s predictive model takes the optimal price for a rental based on its location

To calculate the theoretical speed ratio, divide the number of teeth on the driven sprocket by the number of teeth on the driver sprocket.

For experimental speed ratio, measure the actual speed of the driver and driven sprockets, then divide the driven sprocket speed by the driver sprocket speed.2. Variations in the observed and experimental speed ratio values may be due to factors such as friction, manufacturing tolerances, misalignment of sprockets, chain wear, or elastic deformation in the system.3. To calculate torque on the driver and driven sides, you'll need to know the force applied to the system and the distance from the center of the sprockets to the point of force application. Torque = Force × Distance. The torque on the driven side is generally equal to the torque on the driver side, minus any losses due to friction and inefficiencies.4. To determine input and output horsepower, use the following equation: HP = (Torque × RPM) / 5252. You'll need to measure the torque and RPM on both the input (driver) and output (driven) sides of the system. For the type of sprockets and chain used, refer to the manufacturer's specifications or examine the components.5. To calculate the chain length, use the following formula: Chain Length = (Number of teeth on driver sprocket + Number of teeth on driven sprocket) / 2 + (Center distance between sprockets × 2). This will give you the chain length in terms of the number of chain pitches. Multiply this number by the pitch of the chain to get the actual chain length.

Learn more about theoretical speed here:

https://brainly.com/question/21600339

#SPJ11

Note that, the length of the beam is 4 m. Substituting this value in the equation for I, we get:

We can use the formula for the maximum deflection of a simply supported beam with a point load at the center:

δmax = (FL^3)/(48E*I)

where δmax is the maximum deflection, F is the point load, L is the length of the beam, E is the modulus of elasticity, and I is the second moment of area about the neutral axis.

We can rearrange this formula to solve for I:

I = (FL^3)/(48E*δmax)

a) Second moment of area about the neutral axis:

Substituting the given values, we get:

I = (3010^3(L/2)^3)/(4817510^9*0.857)

I = 2.057×10^-8 L^3

b) Length L of the beam:

To solve for L, we need another equation relating the loads and dimensions of the beam. We can use the equation for the shear force at any point x along the beam:

V(x) = (F/2) - (1510^-3)(x - L/2)

where V(x) is the shear force at a distance x from one end of the beam.

We know that the maximum shear force occurs at the supports, where V(x) = 0. So we can solve for the distance from the supports to the point of maximum shear force:

(1510^-3)(L/2) = (30*10^3/2)

L = 4 m

Therefore, the length of the beam is 4 m. Substituting this value in the equation for I, we get:

I = 2.057×10^-8 * (4)^3

I = 0.132×10^-4 m^4

Learn more about beam at:

https://brainly.com/question/10785313

#SPJ1

The velocity at d is given as 0.518

r / sin 30 = 0.4 / sin 45

r = 0.546 m

From here we have to find the value of vB =

wAB * AM = 1 m / s

angular velocity of BC

= Vb / r = 1.83

Vd - = WBC / r

= 0.518

velocity at C = 0.368

Read more on velocity here:https://brainly.com/question/24445340

#SPJ1

Answer:

the balance is the amount of money owed on an account

Explanation:

To find the deflection and slope at each node and the reactions at each pin or wall for a W150x37 rolled-steel beam with P=150 kN, L=10 m, and E=200 GPa, we need to use beam deflection formulas and equilibrium equations.

1. Calculate the moment of inertia (I) of the W150x37 beam using the formula I = bh^3/12, where b is the base width, and h is the height. You can find these values from the beam's specifications.

2. Determine the maximum deflection (delta_max) at the center of the beam using the formula delta_max = (PL^3)/(48EI), where P is the applied load, L is the length of the beam, E is the modulus of elasticity, and I is the moment of inertia.

3. Calculate the slope (theta) at each end of the beam using the formula theta = (PL^2)/(16EI).

4. For the pin reactions, use the equilibrium equations:
  - The sum of vertical forces should equal zero: R1 + R2 = P, where R1 and R2 are the reactions at each pin.
  - The sum of moments about any point should equal zero. Take the moment about one end of the beam: P(L/2) = R2L, and solve for R2. Then, use the vertical force equation to find R1.

Now you have the deflection and slope at each node and the reactions at each pin or wall for the given W150x37 rolled-steel beam with the specified parameters.

For such more question on equilibrium

https://brainly.com/question/13414142

#SPJ11

Various standards and codes such as ASME B31.4 or B31.8 provide guidelines for pipeline design and selection of pipe diameter that ensure safety and reliability.

To select a pipe diameter that meets the district performance criteria for the MDFF scenario, the diameter of the pipeline must be known. Unfortunately, the question doesn't provide sufficient information regarding the type of pipeline or the specific performance criteria for the MDFF scenario. Therefore, it is impossible to determine the diameter of the pipeline. However, in general, the diameter of a pipeline depends on several factors such as flow rate, fluid type, pressure, and temperature. To ensure that the pipeline meets the desired performance criteria, it is important to consider these factors while selecting the diameter of the pipeline.

learn more about  pipe diameter here:

https://brainly.com/question/12975713

#SPJ4

the strain is 0.15 mm / 50 mm = 0.003.

To calculate the stress (in MPa), first, we need to find the cross-sectional area of the material using the formula for the area of a circle: A = π(D/2)^2, where D is the diameter (8 mm). The area A = π(8/2)^2 = 50.27 mm².

Now, we can calculate the stress using the formula: Stress = Force/Area. Stress = 2,130 N / 50.27 mm² = 42.38 N/mm². Convert the stress to MPa: 42.38 N/mm² = 42.38 MPa.

To calculate the strain, use the formula: Strain = (Change in Length) / (Original Length). The change in length is the elongated length minus the original length: 50.15 mm - 50 mm = 0.15 mm.

learn more about stress here:

https://brainly.com/question/30128830

#SPJ4

In addition, the bot should use the following terms in their answer to the student question: 5 8 7 6 the nodal voltage relative to the ground are: find voltage across . 2.512 (within three significant digits) find the current . 0.502 (within three significant digits) 2.512 (within three significant digits) compute the current and 0.311 0.144

for more such question on resistor

https://brainly.com/question/24858512

#SPJ11

When the water level in the elevated tanks decreases below a certain point, causing the pumps to activate and transfer water from the water storage tank to the elevated tanks.

In a water supply system utilizing a combination of pumps and elevated tanks, a water storage tank begins to add water to the system when the water level in the elevated tanks decreases below a certain point, causing the pumps to activate and transfer water from the water storage tank to the elevated tanks. This ensures a continuous and stable water supply for the users.

Learn more about Water storage tank

brainly.com/question/15763814

#SPJ11

Answer:

Oxygen-inhibited. Hypersensitive

It is important to remove the OIL by polishing the composite resin after it has polymerized. When a composite resin is polymerized, a small layer of uncured material will remain. This layer is called the oxygen-inhibited layer.

What is the oxygen-inhibited layer?The oxygen-inhibited layer (OIL) is a thin layer of uncured resin that covers the surface of a composite resin when it has polymerized. The OIL is produced during the polymerization process because the oxygen in the air inhibits the polymerization of the composite resin on the surface. This results in a layer of uncured material on the top.The OIL may have a negative impact on the durability and mechanical properties of the composite resin. The surface of the composite resin can become weakened, making it more vulnerable to damage. It can also accumulate dirt and bacteria, leading to discoloration and decay.

Learn more about material here:

https://brainly.com/question/13945053

#SPJ11

If a weight of 24,000 lb is supported on a rectangular baseplate that is 9-in wide and 2-ft long and the baseplate rests on a concrete slab, then the stress exerted by the baseplate on the concrete slab is approximately 515,200 lb/ft².

To determine the stress that the baseplate exerts on the concrete slab, we can use the formula for stress:

Stress (σ) = Force (F) / Area (A)

First, let's convert the weight of 24,000 lb to force in pounds by multiplying by the acceleration due to gravity (g) which is approximately 32.2 ft/s^2:

F = 24,000 lb * 32.2 ft/s² = 772,800 lb

Next, let's convert the width of the baseplate from inches to feet:

Width (w) = [tex]\frac{9}{12} = 0.75[/tex] ft

The length of the baseplate is given as 2 ft.

Now, we can calculate the area of the rectangular baseplate:

Area (A) = Length (L) * Width (W) = 2 ft * 0.75 ft = 1.5 ft²

Finally, we can plug the values of force and area into the stress formula to calculate the stress exerted by the baseplate on the concrete slab:

Stress (σ) = Force (F) / Area (A) = [tex]\frac{772,800}{1.5} $\approx$ 515,200[/tex] lb/ft²

Learn more about stress

brainly.com/question/31366817

#SPJ4

One should be concise and provide only relevant details while ignoring any typos or irrelevant parts of the question.Using the following terms in your answer, student question: the terms used in a fuzzy logic system to describe imprecise states or conditions are referred to as: group of answer choices in 200 words

For such more question on variables

https://brainly.com/question/28248724

#SPJ11

The purpose of trench shoring is to prevent movement of soil, underground utilities, roadways, and foundations. It’s mostly to prevent movement

The term for the method of brainstorming is  inversion . Option C

The term for the method of brainstorming in which an engineer or team turns an idea upside down or inside out to look at it in a new way is "inversion."

Inversion involves thinking about a problem or idea from the opposite perspective or reversing the normal order of things to gain a new perspective.

This technique can help to break out of conventional thinking patterns and generate creative solutions to complex problems.

Inversion is commonly used in engineering and design thinking, but can be applied to many different fields and situations.

Read more about brainstorming at: https://brainly.com/question/1606124

#SPJ1

Answer: x=3d , d[tex]\neq[/tex]0

Explanation:

(+1)/dx=(^2+1)

x=3d, d[tex]\neq[/tex]0

Steps

(1)/d x = 2+1

add the number = 2+1 =3

(1)/dx=3

simplify (1)/d = 1/d  remove parentheses

1/dx = 3

Multiply both sides

1/dxd = 3d ; d[tex]\neq[/tex]0

simplify x=3d , d[tex]\neq[/tex]0

Here, the student is asked to consider the following circuit and determine the low pass cutoff frequency:Based on the circuit diagram, we can see that this is a simple RC low pass filter.

For such more question on resistance

https://brainly.com/question/25997303

#SPJ11

From a safety perspective, the most serious lift truck defect is faulty or malfunctioning brakes.

From a safety perspective, the most serious lift truck defect can vary depending on the specific situation and context. However, some commonly identified serious lift truck defects from a safety standpoint may include:

Learn more about hydraulic system

https://brainly.com/question/30388125

#SPJ4

The complete question is:

Fill in the blanks,

From a safety perspective, the most serious lift truck defect is ________________.

The symbolic expression for the effective thermal conductivity (Katts) of the Aramid fiber reinforced composite structure with respect to the heat transfer in the r-direction is: Katts = (2πr)/(te/ke + ta/ka) * (1/N)

The cross-sectional area (A) of the composite structure can be calculated as:

A = πr².

a) Derivation of effective thermal conductivity (Katts) for heat transfer in the r-direction:

The effective thermal conductivity in the radial direction (Katts) can be obtained using the series-parallel method:

Thermal resistance of one layer:

The thermal resistance of each layer can be calculated as:

R = t/k

For epoxy layer: Re = te/ke

For Aramid layer: Ra = ta/ka

Equivalent thermal resistance of the composite structure:

The equivalent thermal resistance of the composite structure can be calculated as:

R_eq = ΣR_i, where i ranges from 1 to N, and N is the total number of layers in the composite structure.

Effective thermal conductivity (Katts):

The effective thermal conductivity of the composite structure can be calculated as:

Katts = 1/(R_eq * (2πr))

where r is the radius of the composite structure.

Substituting the thermal resistance values from step 1 and the number of layers (N) in step 2, we get:

R_eq = (te/ke + ta/ka) * N

Substituting the value of R_eq in the expression for Katts, we get:

Katts = (2πr)/(te/ke + ta/ka) * (1/N)

b) Derivation of effective thermal conductivity (kart) for heat transfer in the z-direction:

The effective thermal conductivity in the axial direction (kart) can be obtained using the series-parallel method:

Thermal resistance of one layer:

The thermal resistance of each layer can be calculated as:

R = t/k

For epoxy layer: Re = te/ke

For Aramid layer: Ra = ta/ka

Equivalent thermal resistance of the composite structure:

The equivalent thermal resistance of the composite structure can be calculated as:

R_eq = ΣR_i, where i ranges from 1 to N, and N is the total number of layers in the composite structure.

Effective thermal conductivity (kart):

The effective thermal conductivity of the composite structure can be calculated as:

kart = 1/(R_eq * A)

where A is the cross-sectional area of the composite structure in the z-direction.

Substituting the thermal resistance values from step 1 and the number of layers (N) in step 2, we get:

R_eq = (te/ke + ta/ka) * N

Substituting the value of R_eq in the expression for kart, we get:

kart = A/[(te/ke + ta/ka) * N]

The cross-sectional area (A) of the composite structure can be calculated as:

A = πr².

Learn more about thermal on

https://brainly.com/question/19666326

#SPJ1

Galvanic corrosion can produce orange/brown streaks on mounting hardware.

The sign of galvanic corrosion on mounting hardware is orange/brown streaks. What is galvanic corrosion? Galvanic corrosion is an electrochemical reaction that occurs when two different metals come into touch with each other in the presence of an electrolyte (such as saltwater). Galvanic corrosion occurs when the cathode and anode are placed in contact with each other. The metal that corrodes is the anode in this situation. In regards to the given question, the sign of galvanic corrosion on mounting hardware is orange/brown streaks. Therefore, the correct option is d) orange/brown streaks. What are the effects of galvanic corrosion? Galvanic corrosion can cause a variety of issues. It may have an impact on the product's structural integrity. For example, galvanic corrosion in bridges and automobiles can reduce the structural integrity of these structures.

learn more about mounting hardware here:

https://brainly.com/question/26867957

#SPJ4

Note that  the magnitudes of the two forces are F1 = √6 N and F2 = 2 N.

Let F1 and F2 be the magnitudes of the two forces. If they act at right angles, their resultant R is given by:

R = √(F1^2 + F2^2)

If they act at 60 degrees, their resultant R' is given by:

R' = √(F1^2 + F2^2 + 2F1F2cos60°) = √(F1^2 + F2^2 + F1F2)

We can set up a system of equations to solve for F1 and F2:

√(F1^2 + F2^2) = √10 ...(1)

√(F1^2 + F2^2 + F1F2) = √13 ...(2)

Squaring both sides of equation (1), we get:

F1^2 + F2^2 = 10

Squaring both sides of equation (2), we get:

F1^2 + F2^2 + F1F2 = 13

Substituting F1^2 + F2^2 = 10 from equation (1), we get:

10 + F1F2 = 13

F1F2 = 3

Now, we can solve for F1 and F2 using the equations:

F1^2 + F2^2 = 10

F1F2 = 3

Multiplying the second equation by 4, we get:

4F1F2 = 12

Substituting F1F2 = 3, we get:

12 = 3(F1^2 + F2^2)

Simplifying, we get:

F1^2 + F2^2 = 4

Using this equation and F1F2 = 3, we can solve for F1 and F2:

F1^2 + F2^2 = 4

F1F2 = 3

Multiplying the first equation by F1F2, we get:

F1^2F2 + F1F2^2 = 12

Substituting F1F2 = 3, we get:

F1^2 + 3F2^2 = 12

Substituting F1^2 = 4 - F2^2 from the first equation, we get:

4 - F2^2 + 3F2^2 = 12

Simplifying, we get:

2F2^2 = 8

F2^2 = 4

F2 = 2

Substituting F2 = 2 in F1^2 + F2^2 = 10, we get:

F1^2 + 4 = 10

F1^2 = 6

F1 = √6

Therefore, the magnitudes of the two forces are F1 = √6 N and F2 = 2 N.

Learn more about magnitude at:

https://brainly.com/question/14452091

#SPJ1

In an active low pass filter, the voltage gain Vout/Vin falls off at a slope of -20dB/decade, as the frequency of the input signal increases. The corner frequency is the frequency at which the voltage gain falls by 3dB or to 70.7% of its maximum value. The signal ratio Vout/Vin at the corner frequency of the filter is 0.707 or -3dB.

An active low pass filter is a type of electronic filter that allows low-frequency signals to pass through, while attenuating high-frequency signals. An active low pass filter, unlike a passive low pass filter, employs an active component such as an amplifier or an op-amp. The input signal is amplified in an active low pass filter, with the output signal being the input signal that has been filtered.The gain of the amplifier decreases at the rate of -20dB/decade as the frequency of the input signal rises, owing to the presence of a capacitor in the feedback loop of the amplifier. The filter's output is 180 degrees out of phase with the input signal since the capacitor leads to a phase shift between the input and output signals. This is referred to as phase shift, and it is a characteristic of all filters that employ capacitors.A capacitor is employed to bypass high-frequency signals to ground in a low pass filter. This capacitor forms a low impedance path to ground for high-frequency signals, while the resistor and feedback network have a high impedance for high-frequency signals. This creates a high-frequency attenuation in the filter, allowing only low-frequency signals to pass through.

For more such question on frequency

https://brainly.com/question/254161

#SPJ11

I am also trained to be concise, avoiding extraneous amounts of detail, and to focus on the relevant parts of the question. Lastly, I am not programmed to ignore any typos or irrelevant parts of the question.

For such more question on frequency

https://brainly.com/question/254161

#SPJ11

Using the general formula for the reluctance, we will get that the  reluctance of the material is 2.3333 × 10^5 At/Wb.

Reluctance (S) is a property of a material that describes how much it opposes the flow of magnetic flux. It is given by the formula:

S = l / (μA)

where the variables are:

Given the values in the problem, we can plug them into the formula written above to get:

S = 0.28 m / (150×10-7 Wb/At.m × 0.08 meter square)

S = 2.3333 × 10^5 At/Wb

Therefore, the reluctance of the material is 2.3333 × 10^5 At/Wb.

Learn more about reluctance at:

https://brainly.com/question/16655664

#SPJ1