Answer:
A) E = 1 N * d = 1 Newton-Meter = 1 Joule
P(ower) = E / t = 1 N-m / t = 1 Joule / sec = 1 W
A coin placed 0.30 m away from the center of a rotating, horizontal turntable just begins to slip when its translational speed is 0.50 m/s. What is the coefficient of static friction between the coin and the turntable
According to the given statement The coefficient of static friction was found to be about 0.0850.
What is static friction ?Static friction is a force that prevents an item from moving. The friction encountered when persons attempt to move a stationary object on a surface without actually causing any relative motion between the body and the surface on which it is located.
The graph below depicts the turntable's constant maximum speed and the centripetal acceleration of the coin.
(a) The centripetal acceleration is caused by static friction.
(b) Using the diagram below,
mai^=fi^+nj^+mg(−j^)
Fy=0nmg, thus n=mg, and Fr=mrv2=f=n=mg
Then, \sμ=rgv²=(30.0cm)(980cm/s2)(50.0cm/s)²
=0.0850
To learn more about Static friction follow the given link:
brainly.com/question/13000653
#SPJ4
The complete question is -
A coin placed 30.0cm from the center of a rotating, horizontal turntable slips when its speed is 50.0cm/s. (a) What force causes the centripetal acceleration when the coin is stationary relative to the turntable? (b) What is the coefficient of static friction between coin and turntable?
state 2 precautionary measures you would take to maintain the efficiency of an accumulator
On gas-loaded accumulators, safety devices like relief valves, burst discs, and temperature fuse plugs are all used as precautionary measures to maintain the efficiency.
What are accumulators?Accumulators are pressurized containers that can hold fluid. When a system needs a boost in power, this stored energy can be used, recharged, and then used again. The right precautions should be taken to keep pressure and temperatures under control because this stored energy can be hazardous.
On accumulators, a number of modest but crucial accessories can be placed to stop the release of this stored energy and guarantee that temperatures stay within their safe operating range.
Learn more about temperature here:
https://brainly.com/question/11464844
#SPJ1
a ball is thrown vertically upwards. After resistance is negligible. What is the variation with tiem fo t of the kinetic energy E_k of hte ball
The variation with time of the kinetic energy E_k of the ball is that it decreases. This is because gravity is acting against the ball and slowing it down, so the kinetic energy is decreasing as the ball slows down.
When the ball is released, the initial kinetic energy, E_k, is given by the equation: E_k = mgh, where m is the mass of the ball, g is the gravitational acceleration, and h is the initial height of the ball. As the ball rises, its height increases, and the potential energy, U, increases. However, this increase in potential energy is at the expense of kinetic energy, so the kinetic energy decreases as the ball rises.
When the ball reaches its maximum height, its kinetic energy is zero as it is at rest. As the ball then begins to fall, its potential energy decreases, and its kinetic energy increases. This is because the ball is falling under the action of gravity, and thus its kinetic energy increases as it accelerates downwards. Overall, the kinetic energy of the ball decreases as it rises and increases as it falls.
This is due to the conservation of energy, which states that the total energy of a system remains constant. As the potential energy increases, the kinetic energy decreases, and vice versa.
To know more about kinetic energy refer to the link brainly.com/question/26472013
#SPJ4
Escriba una oracion empleada de dos adjetivos de significado opuesto unidos por la exprecion y a la ves
Answer:
El castigo de Juan fue justo y a la vez injusto.
Explanation:
Adjetivos opuestos: justo - injusto
La oración significa que el que castigo era merecido, sin embargo, puede ser algo exagerado por lo tanto algo injusto. Describiendo la situación con adjetivos con significado opuesto al mismo tiempo, mediante un conector de simultaneidad que es y a la vez.
The human ear canal is about 2. 8 cm long and can be regarded as a tube open at one end and closed at the eardrum. What is the frequency around which we would expect hearing to be best when the speed of sound in air is 344. 5 m/s? (hint: find the fundamental frequency for the ear canal. )
The human ear canal is closed at one end. Thus, the fundamental frequency of the given ear canal is 3044.64Hz 3044.64 Hz .
Calculation and Explanation:Under air conduction (AC) excitation, the mean resonance frequency of the human middle ear is estimated to be between 0.8 and 1.2 kHz. The typical resonance frequency under bone conduction (BC) excitation, according to research, is higher, at 1.5–2 kHz.
It is a tube with an open end (the concha section) and a closed end (the tympanic membrane), which responds to a quarter-wave by behaving as a resonator. The resonance frequency is described by the equation F=v/4L, where "v" stands for the speed of sound and "L" for the length of the EAC.
The EAR formula should be used: EAR = (1+ i/n)n - 1. I = Stated interest rate, etc.
To learn more about fundamental frequency visit:
brainly.com/question/9424813
#SPJ4
What is the efficiency of a solar cell if 1000 J of solar energy hits the
cell and 200 J are converted into electrical energy?
Answer:
Efficiency = 20%
Explanation:
Given the following data;
Input energy = 1000 Joules
Output energy = 200 Joules
To find the efficiency of the solar cell;
[tex] Efficiency = \frac {Out-put \; energy}{In-put \; energy} * 100 [/tex]
Substituting into the formula, we have;
[tex] Efficiency = \frac {200}{1000} * 100 [/tex]
[tex] Efficiency = 0.2 * 100 [/tex]
Efficiency = 20%
Which of the following is an important starting assumption in models of galaxy formation?
A) Galaxies form first, then black holes.
B) All galaxies start out as spiral galaxies.
C) Black holes form first, seeding the formation of galaxies.
D) Some regions in the universe start out denser than others.
The assumption which is important in models of galaxy formation is Some regions in the universe start out denser than others. Option (D) is correct.
Models of galaxy formation begin with the premise that the universe was initially mostly uniformly filled with hydrogen and helium gas, with some regions of this gas being slightly denser than others.
The nucleus, a central bulge, a disc, spiral arms, and a large halo are the four main structural divisions of this structure. Some of the elements combine with one and other. A small portion of the galaxy, the galactic core is located about 400 light-years from the Milky Way's centre. Massive gas clouds which collapse and rotate are the initial point for galaxies. Stars develop within them as they develop. The collision of entire galaxies can change their appearance. When we look far into space, we can observe galaxies in their infancy.
To learn more about Galaxy :
https://brainly.com/question/14260147
#SPJ4
Arrange the objects from smallest to largest. swap_vert The diameter of Europa swap_vert The diameter of the rings around Saturn swap_vert The diameter of Charon
According to the given information the correct order is Charon ,Europa, Rings around Saturn.
What does diameter mean?A straight line that cuts through the middle of a figure and body is called a diagonal. Particularly: the width of a diameter; a line segment passing thru the center of the circle with its endpoints on the circumference.
What is larger, diameter or width?A circle's diameter is measured as the width of a line connecting its two center points. Since diameter only applies to circular or circularly based objects, such as a sphere or cylinders, the length and width must always be equal.
To know more about Diameter visit:
brainly.com/question/21248758
#SPJ4
Answer:
the order goes
G
E
C
A
Explanation:
Hope this helps.
How much force is needed to accelerate a 63 kg skier at 6 m/s2?
Answer:
378 N
Explanation:
F = ma = (63 kg)(6 m/s²) = 378 N
A skier weighing 63 kg needs 189N of force to accelerate at 6 m/s. The magnitude of the force required to accelerate the sled is 91 newtons.
What is the necessary force to accelerate?An object's acceleration is equal to the net force acting on it divided by its mass, or a = F m, according to Newton's second law of motion. When the object's mass and the net force it is subjected to are known, this acceleration equation can be used to determine its acceleration.
By the second law of Newton, F = ma Add the following numbers:
F=189N F=63kg(2ms 2)
Which two formulas are used to determine acceleration?Formula for acceleration: there are three equations for acceleration:
a = (v_f - v_i) / t;a equals 2 / t2 (d - v_i t)a = F / m ;To learn more about Newton's second law here:
https://brainly.com/question/13447525
#SPJ1
can some one help me with my last question please i really need help
Answer: yeah for sure but post the picture
Explanation:
Lol
How do you find torque with force and distance?
Torque = force x distance from point of rotation
Torque is a measure of the turning effect of an applied force about a specific point or axis. It is calculated by multiplying the force applied to an object by the distance from the point of rotation to the point where the force is applied. The greater the force or the longer the distance from the point of rotation, the greater the torque. The unit of torque is typically Newton-meters (N·m) in the International System of Units (SI) or pound-feet (lb·ft) in the imperial system. Torque is essential in various fields such as physics, mechanics, engineering and robotics.
To know more about Torque click below:
https://brainly.com/question/6855614#
#SPJ4
which one is the lunar eclipse?
Answer:
Yes it would be a lunar eclipse here is an image that I found that might help but during a lunar eclipse when the moon is directly behind earth it will be a full moon
Explanation:
Salt dissolves in water to form saltwater. Is this considered a chemical change or a physical change
Salt dissolves in water to form saltwater. This kind of change is regarded as a chemical change.
A physical change is a kind of change in which only the physical properties of matter change. In a physical change, neither the composition nor the chemical nature of matter is changed.
A chemical change involves a chemical process that results in the production of new substances. When you dissolve salt in water the sodium chloride dissociates in Na+ and Cl- ions which can be written in the form of a chemical reaction as,
NaCl → Na+(aq) + Cl-(aq)
Thus, dissolving salt in water is an example of a chemical change.
To know more about chemical change:
https://brainly.com/question/2496486
#SPJ4
The set of spectral lines that we see in a star's spectrum depends on the star's (a) atomic structure. (b) chemical composition. (c) rotation rate.
The set of spectral lines that we see in a star's spectrum depends on the star's (b) chemical composition, (d) temperature.
The spectral lines of a star are determined by its chemical composition and temperature. These properties determine the number and type of atoms present in the star's atmosphere. Each type of atom has its own unique set of spectral lines, and the temperature of the star determines the energy level of the atoms, which affects the wavelengths of the spectral lines emitted. The rotation rate and atomic structure of a star do not affect the set of spectral lines we see in its spectrum.
learn more about spectral lines here
https://brainly.com/question/27494244
#SPJ4
How do you calculate torque of a shaft?
Divide the radius by the shear stress and the polar moment of inertia to find the shaft torque.
A device that measures shaft torque records the degree to which a shaft will twist in the presence of a specific amount of force. A shaft will twist less than one with a torque of 3 degrees than one with a torque of 5 degrees, and so on.
Does torque equate to rotation?The rotating equivalent of force is torque. So an object will rotate with an angular acceleration in response to a net torque. A torque must be described about the rotational axis since every rotational motion has an axis of rotation. A torque is an applied force that rotates an object about its axis.
To know more about shaft torque visit:-
https://brainly.com/question/12873980
#SPJ4
What are the two primary factors that control what type of magma erupts from a volcano and what type of volcano it will create?
Answer:
answers are located on the picture attached to this answer
Explanation:
The Cessna Cardinal, a single-engine light plane, has a wing with an area of 16. 2 m^2, and an aspect ratio of 7. 31. Assume the span efficiency factor is 0. 62. A. If the airplane is flying at standard sea-level conditions with velocity of 251 km/h, what is the induced drag when the total weight is 9800N b. Calculate the induced drag when the
The Cessna Cardinal, a single-engine light plane, has a wing area of 16.2 m² and an aspect ratio of 7.31 with span efficiency factor of 0.62 then the induced drag when the total weight is 9800 N is 18.8 N.
Given that,
Wing area (A) = 16.2m²
Aspect ratio (r) = 7.31
Efficiency factor (e) = 0.62
Weight of plane (W) = 9800 N
Velocity of airplane (v) = 251 km/h = 251× 5/18 = 69.72 m/s
We know,
Dynamic pressure (p) = 1/2ρv²
where ρ is density of plane = 1.225
p = 1/2 × 1.225 × 69.72 × 69.72 = 2977.29 pa
Lift coefficient Cl = W/p × A = W/(1/2ρv²) A
where, A is the area of wing
Cl = 9800/2977.29 × 16.2 = 0.203
Induced drag coefficient (Cd) = Cl²/πer² = (0.203 × 0.203)/(π × 0.62 × 7.31 × 7.31) = 0.041/(104.08) = 0.39×10⁻³
Induced drag (d) = p × A × Cd = 2977.29 × 16.2 × 0.39 × 10⁻³ = 18.8 N.
To know more about drag:
https://brainly.com/question/30024162
#SPJ4
An artificial satellite is moving in a circular orbit of radius 24,600 km. Calculate its speed if it takes 12hours to revolve around the earth.
Answer:
the speed of the satellite is 12,880.53 km/h
Explanation:
Given;
radius of the circular orbit, r = 24,600 km
time taken to revolve around Earth, t = 12 hours
The circumference of the satellite is calculated as;
L = 2πr
L = 2π x 24,600 km
L = 49,200π km
L = 154,566.36 km
The speed of the satellite;
v = L/t
v = 154,566.36 / 12
v = 12,880.53 km/h
Therefore, the speed of the satellite is 12,880.53 km/h
How does the gravitational pull of different objects in space affect other objects in space?
Answer:
Every object in space exerts a gravitational pull on every other.
Explanation:
gravity influences the paths taken by everything traveling through space. It is the glue that holds together entire galaxies. It keeps planets in orbit. It can also cause life-destroying asteroids to crash into planets.
A block is resting on an slope. (Figure 3) Which of the following forces act on the block? Check all that apply. O weight O static friction O normal force O kinetic friction O force of push
The correct option is A, B, and C. A block resting on a slope is Weight, static friction, and Normal force.
Static friction is a force that continues an item at relaxation. Static friction definition can be written as: The friction skilled while individuals try to move a desk-bound object on a surface, without surely triggering any relative movement between the frame and the surface on which it's miles.
Static friction is a form of friction force that acts on a body when there's no relative motion between the object and the surface. So, it can act even if the frame is in motion however there should be no relative motion.
A pressure acting on an item is said to be a static force if it no longer exchanges the scale, function, or route of that precise object. The pressure implemented to a structure acts as a load to that precise structure, that is why static force is likewise called a static load.
To learn more about Static friction visit here:
brainly.com/question/13000653
#SPJ4
Complete Question:
A block is resting on a slope. (Figure 3) Which of the following forces act on the block?
Check all that apply.
A). Weight
B). Static friction
C). Normal force
D). Kinetic friction
E). Force of push
When a newly forming star is at its greatest luminosity, what is its energy source?
A. nuclear fusion of hydrogen into helium
B. A newly forming star has no energy source because it does not shine at all until it becomes a true main-sequence star.
C. radioactive decay of unstable isotopes
D. gravitational contraction
The correct option is D, when a newly forming star is at its greatest luminosity, its energy source is gravitational contraction.
Gravitational contraction is the process by which objects in the universe collapse under their own gravity. It occurs when the internal pressure of an object is not strong enough to resist the pull of gravity. This can occur on small or large scales, from the collapse of a gas cloud to form stars to the collapse of entire galaxies.
As an object collapses, its temperature and density increase, and the collapse accelerate due to gravitational potential energy being converted into kinetic energy. This process can lead to the formation of stars, planets, and other objects in the universe. It is also the source of much of the energy released by stars, which powers the universe. Gravitational contraction is an important part of the astronomical theory of the formation of galaxies, stars, and planets.
To learn more about Gravitational contraction visit here:
brainly.com/question/15969901
#SPJ4
Which organism would most likely have new gene combinations?
Answer:
a hamster resulting from sexual reproduction
1. What happens to an atom when it gains electrons? *
Answer: An atom that gains or loses an electron becomes an ion. If it gains a negative electron, it becomes a negative ion. If it loses an electron it becomes a positive ion
Answer:
when an atom gains electrons, it gains a negative charge
Explanation:
hope I helped you
. Suppose a positively charged object A is brought in contact with an uncharged object B in a closed system. What type of charge will be left on object B
Charging by Contact is positive. On object B, a positive charge will remain.
What is Charge?The fundamental physical property of matter, electric charge, exerts a force when kept in an electric or magnetic field. A magnetic field is produced by a moving electric charge, and an electric charge is associated with an electric field. Magnetic and electric fields combine to form the electromagnetic field. The interaction of the charges results in the electromagnetic force, which is the fundamental force in physics. Throughout this session, tell us about electric charges, their types, and their traits.
A scalar quantity is an electric charge. Only when a quantity complies with the laws of vector addition, such as the triangle law of vector addition and the parallelogram law of vector addition, can it be said to be a vector in addition to having a magnitude and direction. In the case of an electric current, the resultant current of these two currents at a junction is an algebraic sum rather than a vector sum. Therefore, despite having magnitude and direction, an electric current is a scalar quantity.
Learn more about Charge from given link
https://brainly.com/question/18102056
#SPJ4
suggest how the thermal conductivity of a metal depends on its temperature
Answer:
With an increase in temperature, the electrical conductivity of a pure metal decreases. This implies that the thermal conductivity of the pure metal shows little variance with an increase in temperature. However, a sharp decrease is observed when temperatures approach 0K
convert-73°c to kelvin scale
Answer:
200 K
Explanation:
0 °C = 273 K
-73°C = 273 K - 73 K = 200 K
Two objects with negative charges of 6.2 nC each are separated by 0.3 m. What is the size and direction of theforce between the two charges?
A negatively charged object is one that has more electrons than protons.
What is the negative charge?A negative charge is present when an object has more electrons than protons. An atom has a positive charge when there are more protons than electrons in it. The charges of protons are positive while those of electrons are negative. The coulomb is used to measure charge (C).
The opposite of a charge's attraction is the opposite of its repellency. Therefore, a positive charge attracts a negative charge, whereas two negative charges repel one another. Along the boundary between the two charges, attraction or repulsion occurs.
Along the line that connects the centres of the two objects, the force is applied in that direction. Coulomb's law results in a negative value if the two charges have opposing signs. As a result, the force separating the particles is an attractive force.Coulomb's law produces a favourable outcome if the two charges have the same signs.
Therefore, the answer is 12.4 c positive.
To learn more about negative charges refer to:
https://brainly.com/question/24745720
#SPJ1
Two objects with negative charges of 6.2 nC (Coulomb) each are separated by 0.3 m. the size and direction of the force between the two charges is 3.8387038*10^12 N and toward left.
What is Coulomb?In the International System of Units, the unit of electric charge is the coulomb. It is equivalent to 5 1027/801088317 elementary charges in the current version of the SI, as well as the electric charge given by a 1 ampere continuous current in 1 second, e.Solution:
Given :
Two objects with negative charges of 6.2 nC (nano coulomb ) each.
Separation= 0.3 m.
We will use the following Coulomb’s Law.
F = k*|q1| |q2|/r2 ∵ where k = 8.9876 × 109 N·m2
Putting the values, we get
F = 8.9876 × 109*|6.2| |6.2|/0.3^2
F=3.8387038*10^12 N
To know more about coulomb visit
https://brainly.com/question/16222732
#SPJ1
The current in a ________
Answer here
circuit is the same at every point?
Answer:
Series.
Explanation:
Current is the same in each device since there is only a single pathway for the charge to flow.
Two long parallel conductors carries I1 and I2 in opposite directions. Determine the magnetic field between the wires
Answer:
B1 = μ_o•I1/2πr
Explanation:
According to the right hand rule, we can say that the magnetic field at the second wire due to the current being carried in first wire is given by;
B1 = μ_o•I1/2πr
Where;
r is distance that separates the two wires
μ_o is a constant known as permeability of free space
I1 is current in wire 1
What is the velocity of the particle at time t 0?
The velocity of the particle at t=0 is zero because the particle is in rest position and did not moving at any of the instance or travelling at an uniform speed through out the whole journey or yet did not start from the source point.
Velocity is the rate of change of velocity. At any point on a trajectory, the magnitude of the velocity is given by the rate of change of velocity in both magnitude and direction. Velocity of the body that we can consider is the increasing value of the velocity of any object at a constant rate and that of we can calculate. Hence by the primary information that we have we can formerly consider that the velocity which is acting on the particle at t=0 is zero because the particle is in rest position and did not moving at any of the instance or travelling at an uniform speed through out the whole journey or yet did not start from the source point.
Learn more about Velocity:
brainly.com/question/18084516
#SPJ4