Take 100 points look the picture​

Answer:

True. If you bring a bowling ball away from earth it would weigh less because the less gravity pushing down on it.

Answer:

f

Explanation:

After solving the equation the wave is traveling at a velocity of 3 m/s.

Velocity is a vector quantity that describes the rate at which an object changes its position. It is a measure of both the speed and the direction of an object. Velocity is typically expressed in terms of meters per second (m/s). When an object is in uniform motion, its velocity is constant, meaning that it is not changing in magnitude or direction. If an object is accelerating, its velocity is changing over time, either in magnitude, direction, or both.

The velocity of the wave can be calculated using the following equation:
Velocity = Wavelength x Frequency
In this case, the wavelength is 0.5 m and the frequency is 6 Hz (6 cycles per second). So, the velocity of the wave is:
Velocity = 0.5 m x 6 Hz = 3 m/s
This means that the wave is traveling at a velocity of 3 m/s.

To learn more about velocity
https://brainly.com/question/29223620
#SPJ1

Answer:

b. a lens does not focus all colors of light to the same place.

Explanation:

Chromatic aberration is a defect of a lens. In this defect, the lens is unable to focus the different wavelengths of the light on a single focal point. It is also known as chromatic distortion and color fringing. It is caused by the dispersion of light while passing through a lens. As a result, the image might become blurred and different colors are observed around its edges. It can be corrected by the use of a combination of converging and diverging lenses.

Hence, the correct option will be:

b. a lens does not focus all colors of light to the same place.

Answer: [tex]32.65\ m[/tex]

Explanation:

Given

mass of laptop m=2 kg

The velocity of car u=8 m/s

The coefficient of static friction is [tex]\mu_s=0.4[/tex]

The coefficient of kinetic friction is [tex]\mu_k=0.2[/tex]

As the car is moving, so the coefficient of kinetic friction comes into play

deceleration offered by friction [tex]\mu_kg=0.2\times 9.8\ m/s^2[/tex]

Using the equation of motion [tex]v^2-u^2=2as\\[/tex]

insert the values

[tex]0^2-8^2=2(-0.2\times 9.8)s\\\\s=\dfrac{64}{1.96}\\\\s=32.65\ m[/tex]

The conductivity of a conductor refers to its ability to conduct electrical current.

A material that has high conductivity allows electrical charges to flow through it easily and with little resistance, while a material with low conductivity does not allow electrical charges to flow as easily and has more resistance.

The conductivity of a conductor is determined by the number of free electrons in the material, as well as how easily these electrons can move through the material.

In a conductor, the atoms are closely packed together and the electrons are not tightly bound to the atoms, allowing them to move freely through the material and carry an electrical charge. This facilitates the flow of electrical current through the material, resulting in high conductivity.

Learn more about conductors:

https://brainly.com/question/18084972

Impact Speed means the maximum speed of impact tested upon the bumper of the vehicle pursuant to sections 581.6 and 581.7 of part 581 of title 49 of the Code of Federal Regulations.

To learn more about impact speed to refer:

https://brainly.com/question/15695646

#SPJ1

Answer:

Probably copper wire

Explanation:

I took the class and that's the only one that sounds right but I'm pretty dum lol

Important Formulas:

[tex]w=Fd[/tex]

work(measured in joules) = force(measured in newtons) * distance(measured in meters)

__________________________________________________________

Given:

[tex]m=42kg[/tex]

[tex]F=225N[/tex]

[tex]d=12m[/tex]

[tex]w=Fd[/tex]

__________________________________________________________

Finding work:

[tex]w=Fd[/tex]

[tex]w=225\times12[/tex]

__________________________________________________________

[tex]\fbox{w = 2700 Joules}[/tex]

Answer:

Velocity is the displacement of an object divided by the time interval.

Explanation:

Let's consider each choices:

    1. Velocity is not the magnitude of speed. Velocity is a vector quantity which means it consists of both direction and magnitude. Speed is the magnitude of velocity, not the other way around.

    3. Velocity describes how fast an object is changing speed. If a speed changes each time interval, that is not a velocity but rather the magnitude of acceleration. Magnitude of acceleration is change in speed over time. Acceleration is the one that describes how velocity is changing through time.

    4. Speed and velocity refer to the same vector quantity. Speed is not a vector quantity but a scalar quantity which only has magnitude. Speed is also considered as the magnitude of velocity as well.

Therefore, the only correct choice is 2. Velocity is the displacement of an object divided by the time interval. This is true since velocity is change in position (displacement) over time.

Answer:

he is right its c

Explanation:

Answer:

a current that rapidly switches direction

Explanation:

Answer:

Explanation:

From the given information:

The speed of a synchronous motor in relation to its frequency can be represented with the formula:

[tex]n_{sm}= \dfrac{120f_{se}}{P}[/tex]

where,

the electrical frequency [tex]f_{se}[/tex] is measured in Hz

the number of poles = P

For us to estimate the number of poles to have 50 Hz - 60 Hz Power, then we need to relate the frequencies of the above equation.

i.e

[tex]\dfrac{120(50 \ Hz)}{P_1}= \dfrac{120( 60 \Hz)}{P_2} \\ \\ \dfrac{6000 \ Hz}{P_1}= \dfrac{7200 \ Hz}{P_2} \\ \\ \dfrac{P_2}{P_1}=\dfrac{7200}{6000} \\ \\ \\ \dfrac{P_2}{P_1}= \dfrac{12}{10}[/tex]

Thus, we can conclude that 10 poles synchronous motor is attached with 12 poles synchronous generator in order to convert 50 Hz to 60 Hz power.

Answer:

12583.2 J or 12.5832 KJ

Explanation:

Work done can be expressed as force multiplied by displacement, or

W = Fs

In this case, we can calculate the force by using F = mg.

m is the mass, 214 kg, and g is gravitational acceleration, which is 9.8 m/s/s.

So, we Calculate 214 * 9.8 to get 2097.2

The displacement is 6m.

So, by doing W = Fs, we get

2097.2 * 6 = 12583.2 Joules

Answer:

Should be 17.8m/s

Explanation:

Initial momentum = Final momentum

(m1×v1)+(m2×v2)=(m1+m2)v since its an inelastic collision.

Students are instructed in subject-specific classes by science professors. They develop lesson plans, assess student performance, and educate using lectures, technology.

The teacher who gives their best in order to develop the skills in all student of their class. A good teacher has to be a great command of his/her subjects.

He/she has to put their effort to improve the weak student of the class as well must appreciate the effort of good students.

The role of the teacher and the learner in a natural science and technology classroom​ is;

Students are instructed in subject-specific classes by science professors. They develop lesson plans, assess student performance, and educate using lectures, technology,

They also serve as role models for anticipated conduct in order to develop and maintain an ordered, disciplined classroom.

They must also be analytical since they must analyze kids' development and modify lesson plans for special-needs children.

They may create and sustain interpersonal ties with students, parents, other staff members, and administrators.

Hence the role teacher is to instruct the student, maintain discipline and educate using technology.

To learn more about the teacher refer to the link;

https://brainly.com/question/10283004

Answer:

F = G M m / R^2 = m a

G M / R^2 = a

M = a R^2 / G

M = 1.56 N/kg * 6.35 m^2 / 6.67E10-11 N-m^2 / kg^2

M = 1.56 * 6.35 / 6.67E-11 kg

M = 1.49 * 10^11 kg

Answer:

[tex]\text{Using the formula: }v=\frac{d}{t}\\\therefore vt=d\\\text{Plug and chug:}46.2(8.66)=400.092\text{ metres}[/tex]

Answer:

Useable energy, electricity

Answer:

800

Explanation:

10^2 = 100
8 x 100  = 800

Answer:

A. Q = 2.74 x 10⁷ J = 27.4 MJ

B. E = 3.91 x 10⁸ J = 391 MJ

Explanation:

A.

Heat rejected can be found as follows:

[tex]Q = mL[/tex]

where,

Q = Heat rejected = ?

m = mass = 82.1 kg

L = Latent Heat of fusion = 334000 J/kg

Therefore,

[tex]Q = (82.1\ kg)(334000\ J/kg)[/tex]

Q = 2.74 x 10⁷ J = 27.4 MJ

B.

First, we will calculate the efficiency of the Carnot Cycle as follows:

[tex]Efficiency = 1-\frac{T_1}{T_2}[/tex]

where,

T₁ = Heat intake temperature = 0°C + 273 = 273 k

T₂ = Heat rejection temperature = 20.6°C + 273 = 293.6 k

Therefore,

[tex]Efficiency = 1 - \frac{273\ k}{293.6\ k} \\\\Effciency = 0.07[/tex]

Therefore, the energy input required is:

[tex]Efficiency = \frac{Q}{E}\\\\E = \frac{Q}{Efficiency} = \frac{2.74\ x\ 10^7\ J}{0.07}[/tex]

E = 3.91 x 10⁸ J = 391 MJ

Answer:

The answer is C:

Explanation:

HOPE IT HELPS!!

The option that correctly states what happen to the kinetic energy and the momentum of the two-cart system as a result of the collision compared to those quantities before the collision is

B) Kinetic energy: Increases; Magnitude of Momentum: Stays the same

The energy an object has as a result of motion is known as kinetic energy. A force must be applied to an object in order to accelerate it. We must put in effort in order to apply a force.

Since the elastic potential energy that was initially stored in the compressed spring has now been converted into kinetic energy, the system's total energy should be conserved. As a result, the system's kinetic energy increases. As a result, the system's kinetic energy rises.

The magnitude of the two-cart system's net momentum remains constant because there is no outside force acting on it, which implies that the system's overall momentum should be conserved.

Therefore, the correct option is B.

Learn more about energy on:

https://brainly.com/question/25959744

#SPJ1

A bar magnet's magnetic field lines flow from its north pole toward its south pole, just like they do in all magnets. Field lines that begin close to a pole's edges stay nearby the bar magnet longer than those that begin closer to the pole's centre.

Because the molecules in magnets are arranged so that their electrons spin in the same direction, magnets are unique. This configuration and motion produces a magnetic force that emanates from a north- and south-seeking pole, respectively.

At the poles, it is strongest.

To know more about magnetic field visit:-

brainly.com/question/14848188

#SPJ1

Lenses, which are pieces of curved, clear glass, were employed in early telescopes to focus light.

Curved mirrors are used by the majority of telescopes nowadays to collect light from the night sky. Light is focused by a telescope's mirror or lens' shape.

Astronomers use a telescope to observe distant things. Curved mirrors are used by the majority of telescopes, including all large telescopes, to collect and concentrate light from the night sky.

The original telescopes employed lenses, which are simply curved pieces of clear glass, to focus light. The "optics" of a telescope are the mirrors or lenses. Strong telescopes may view objects that are extremely faint and incredibly far away.

Therefore, Lenses, which are pieces of curved, clear glass, were employed in early telescopes to focus light.

To learn more about Telescope, refer to the link:

https://brainly.com/question/556195

#SPJ1

Newton's subsequent law expresses that power is corresponding to what exactly is needed for an object of consistent mass to change its speed. This is equivalent to that item's mass increased by its speed increase.

We use Newtons, kilograms, and meters each second squared as our default units, albeit any proper units for mass (grams, ounces, and so forth) or speed (miles each hour out of every second, millimeters per second², and so on) could unquestionably be utilized also - the estimation is the equivalent notwithstanding.

Hence, the appropriate answer will be 399,532.

Net Force = 399532

Answer: Visual acuity: sharpness of vision.

Myopia: nearsightedness

Refraction: bending of light rays.

Emmetropia: normal vision.

Accommodation: changes the shape of the eye lens to focus light on the retina.

Presbyopia: age-related farsightedness due to loss of elasticity in the lens.

Astigmatism: reduction in visual acuity due to changes in the cornea or lens.

Hyperopia: farsightedness

Myopia and hyperopia are refractive errors of the eye.

Presbyopia occurs in old age people.

Explanation:

Visual acuity: It can be defined as the inability to observe the details of shape of the object. Person loses sharpness in vision.

Myopia: It is a defect in vision in which person is able to observe the near by objects clearly but not able to see the distant objects.

Refraction: It can be defined as the bending of beam of light when it passes through from one substance to another.

Emmetropia: It is a vision without any defect.

Accommodation: It is the ability of the eye to adjust its focal length and adjusting the light on focus.

Presbyopia: It can be defined as the loss of ability of eye to focus on the object. It occurs in old age.

Astigmatism: It is a refractive error in which the eye does not focus light on retina.

Hyperopia: It is also called as farsightedness. Distant objects can be seen clearly but nearby appears blurry.

Answer:

A Shunt is a passive element, usually resistive, that is used to bypass current around another element, like a meter, that is not able to handle the full current flow. ... A Multiplier is an active element that amplifies a voltage or current to enable a less sensitive device or circuit to make use of it.

A Shunt which is a passive element resistive used to bypass current around another element, like a meter whereas A Multiplier which is an active element that amplifies a voltage or current to  a less sensitive device

The shunt can defined as  it is generated by a resistor with an extremely low resistance that is coupled in parallel associated with some other resistor; A  resistance of a shunt could be used just to increase the frequency of an ammeter measurement.

one of the example is The galvanometer employs a shunt to measure huge currents, can be also used as diode. some of the major Uses of shunt are used to  determine big currents in galvanometers.

Shunt can safeguards the circuit where it is linked in parallel to the galvanometer in a circuit and act as an ammeter and the Current should be measured.

For more details  shunt,  visit

https://brainly.com/question/15074025

#SPJ2

Which of the following are characteristics of noble gases?

[tex]{ \bf{ \underbrace{Answer :}}}[/tex]

[tex]\sf\red{B. \:They're\: inert.}[/tex] ✅

[tex]\sf\purple{D.\: They \:don't \:react\: with\: other\: elements.}[/tex]✅

[tex]\circ \: \: { \underline{ \boxed{ \sf{ \color{green}{Happy\:learning.}}}}}∘[/tex]

Explanation:

work a force is measured in newton-meters (N-m)

[tex] \huge \hookrightarrow \mathfrak{ \green{Answer}}[/tex]

we know,

[tex] \boxed{ \small{workdone = force \times displacement}}[/tex]

[tex]\longmapsto \: work \: done = N \times m[/tex]

[tex]work \: \: done \: \: is \: \: measured \: \: in \: \: \boxed {\color{gold}{Nm}}[/tex]

Nm = Newton meter

Answer:

Explanation:

Let the spring constant of spring A and B be k₁ and k₂ . Mass of box X and Y be m₁ and m₂ .

Force created in spring which is stretched by d is kd where k is spring constant .

At her lab in Orlando, Florida,

k₁ x .0204 m = m₁ g where g is acceleration due to earth's gravity

k₁ = 49 m₁ g

At a research station on the moon

k₁ x .34 x 10⁻² m = m₁ g₁ where g₁ is acceleration due to gravity at moon

k₁  = 294 .11 m₁ g₁

49 m₁ g = 294 .11 m₁ g₁

g = 6.0022  g₁

At a research station on the moon

k₁ x .54 x 10⁻² m = m₂ g₁

k₁ = 185.18 m₂ g₁

294 .11 m₁ g₁ = 185.18 m₂ g₁

1.588 m₁ =  m₂

1 )

At her lab in Orlando, Florida,

k₁ x d  = m₂ g , where d is the new stretch that is to be calculated .

185.18 m₂ g₁ d =m₂ g

185.18 d  g₁ = g

185.18 d  g₁ = 6.0022  g₁

d = .03241 m

= 3.24 cm .

2 )

At a research station on the moon

when Block Y is hanging from Spring B

k₂ x .013   = m₂ g₁

k₂ = 76.92 m₂ g₁

At her lab in Orlando, Florida,

Spring B stretch when Block X is hanging from it

k₂ d₁ = m₁ g

76.92 m₂ g₁ d₁ = m₁ g

76.92 m₂ g₁ d₁ = m₁ 6.0022  g₁

76.92 m₂  d₁ = m₁ 6.0022  

12.815  x  1.588 m₁ x  d₁ = m₁

d₁ = .049 m

= 4.9 cm .

In this exercise we have to use the knowledge of springs to calculate the distance from it, that way:

A)d=3.24 cm

B)d=4.9 cm

So, before starting the calculations, we have to organize the values ​​and put everything in function of a single unknown such as:

[tex]k_1 * 0.34 * 10^{-2} m = m_1 g_1\\ k_1 = 294 .11 m_1 g_1\\49 m_1 g = 294 .11 m_1 g_1\\g = 6.0022 g_1\\k_1 *0 .54 * 10^{-2} m = m_2 g_1\\k_1 = 185.18 m_2 g_1\\294 .11 m_1 g_1 = 185.18 m_2 g_1\\1.588 m_1 = m_2[/tex]

A) By calculating the distance we find that:

[tex]k1_1 * d = m_2 g\\185.18 m_2 g_1 d =m_2 g\\185.18 d g_1 = g\\185.18 d g_1 = 6.0022 g_1\\d = 0.03241 m= 3.24 cm[/tex]

B) So now calculating the distance from the lab to the moon, so:

[tex]k_2* 0.013 = m_2 g_1\\k_2 = 76.92 m_2 g_1\\k_2 d_1 = m_1 g\\76.92 m_2 g_1 d_1 = m_1 g\\76.92 m_2 g_1 d_1 = m_16.0022 g_1\\76.92 m_2 d_1 = m_1 6.0022\\12.815 * 1.588 m_1 * d_1= m_1\\d_1 = 0.049 m = 4.9 cm[/tex]

See more about springs at brainly.com/question/4433395