If methane is compressed in a steady-state adiabatic compressor (87% efficient) to 0.4 mpa, then the required work per mole of methane is 4.04 kJ/mol.
To determine the required work per mole of methane, we can use the following formula:
[tex]W = \frac{(P_2V_2 - P_1V_1)}{n} * \eta[/tex]
Where:
W is the work done per mole of methane in kJ
P₁ is the initial pressure of methane
V₁ is the initial volume of methane
P₂ is the final pressure of methane
V₂ is the final volume of methane
n is the number of moles of methane
η is the efficiency of the compressor
Assuming that the compression process is reversible and adiabatic, we can use the following relationships:
[tex]\frac{P_2}{P_1} = (\frac{V_1}{V_2})^{\gamma}[/tex]
[tex]\frac{T_2}{T_1} = (\frac{V_1}{V_2})^{(\gamma-1)}[/tex]
where:
[tex]\gamma = \frac{C_p}{C_v}[/tex] is the ratio of specific heats of methane
[tex]C_p[/tex] is the specific heat at constant pressure
[tex]C_v[/tex] is the specific heat at constant volume
Since the process is adiabatic, there is no heat transfer (Q = 0) and therefore the compression is reversible, so we can use the above relationships.
Let's assume that we have one mole of methane, and use the ideal gas law to find the initial volume:
[tex]P_1V_1 = nRT_1[/tex]
Where:
R is the gas constant for methane
T₁ is the initial temperature
Assuming standard temperature and pressure (STP) conditions (T₁ = 273.15 K, P₁ = 1 atm), we have:
[tex]V_1 = \frac{nRT_1}{P_1} = \frac{(1)*(8.314 )*(273.15)}{(1 * 101.325)} = 22.414[/tex] L/mol
Next, we can use the relationships for adiabatic compression to find the final volume and temperature:
[tex]\frac{P_2}{P_1} = (\frac{V_1}{V_2})^{\gamma}[/tex]
⇒ [tex]\frac{0.4}{101.325} = (\frac{22.414}{V_2})^{1.31}[/tex]
[tex]V_2 = 6.903[/tex] L/mol
[tex]\frac{T_2}{T_1} = (\frac{V_1}{V_2})^{\gamma-1}[/tex]
[tex]T_2 = T_1 * (\frac{V_1}{V_2})^{\gamma -1}[/tex]
[tex]T_2 = 273.15* (\frac{22.414}{6.903})^{(1.31-1)}[/tex]
[tex]T_2 = 550.1 K[/tex]
Now we can substitute the values into the formula for work:
[tex]W = \frac{(P_2V_2 - P_1V_1)}{n} * \eta[/tex]
[tex]W = \frac{[(0.4*6.903) - (1*22.414)]}{1} * 0.87[/tex]
[tex]W = -4.04[/tex] kJ/mol
the negative sign indicates that work is done on the system (i.e. the compressor does work on the methane). Therefore, the required work per mole of methane is -4.04 kJ/mol
learn more about methane
brainly.com/question/29481150
#SPJ4
is 1250g of carbon is reacted with excess water, and 710g of methane (ch4) was recovered, what was the percent yield of the reaction
The balanced chemical equation for the reaction between carbon and water to form methane is:
C + 2H2O → CH4 + CO2
From the equation, we see that one mole of carbon reacts with two moles of water to produce one mole of methane.
To determine the theoretical yield of methane, we first need to convert the mass of carbon to moles:
1250 g C × (1 mol C/12.011 g C) = 104.11 mol C
Since one mole of carbon produces one mole of methane, the theoretical yield of methane is also 104.11 mol.
Next, we can use the molar mass of methane to convert the theoretical yield from moles to grams:
104.11 mol CH4 × (16.043 g CH4/mol) = 1669.9 g CH4
Therefore, the theoretical yield of methane is 1669.9 g.
The percent yield of the reaction is the actual yield (the amount of methane recovered) divided by the theoretical yield, multiplied by 100%.
percent yield = (actual yield / theoretical yield) × 100%
To find the actual yield, we use the given mass of methane recovered:
actual yield = 710 g CH4
So, the percent yield is:
percent yield = (710 g CH4 / 1669.9 g CH4) × 100%
percent yield = 42.5%
Therefore, the percent yield of the reaction is 42.5%.
learn more about electrolysis here:brainly.com/question/16763470
#SPJ4
Suppose this system is analyzed at a particular temperature, and the equilibrium concentrations are found to be [SiH4] = 0.018 M, [Cl2] = 0.0043 M, [SiCl4] = 2.2×10-4 M, and [H2] = 3.9×10-4 M. Calculate the value of K for this reaction. Also, what is the value of K for the reverse reaction at this temperature?
The value of K for the reverse reaction at the given temperature is 9.35.
The given reaction is:
SiH4(g) + 2Cl2(g) ⇌ SiCl4(g) + 2H2(g)
The equilibrium concentrations are given as follows:
[SiH4] = 0.018 M
[Cl2] = 0.0043 M
[SiCl4] = 2.2×[tex]10^{-4}[/tex]M
[H2] = 3.9×[tex]10^{-4}[/tex]M
The expression for the equilibrium constant (K) for the given reaction is:
K = ([SiCl4] x [H2]) / ([SiH4] x [Cl2])
Substituting the given values in the above equation, we get:
K = (2.2×[tex]10^{-4}[/tex]Mx (3.9×[tex]10^{-4}[/tex]M)^2) / (0.018 x (0.0043))
K = 0.107
Therefore, the value of K for this reaction at the given temperature is 0.107.
For the reverse reaction, we need to take the reciprocal of K to obtain the equilibrium constant for the reverse reaction. The reverse reaction can be obtained by reversing the direction of the given reaction, which gives:
SiCl4(g) + 2H2(g) ⇌ SiH4(g) + 2Cl2(g)
The equilibrium constant for the reverse reaction is given by:
K' = 1/K
Substituting the value of K in the above equation, we get:
K' = 1/0.107
K' = 9.35
Learn more about equilibrium constant here:
https://brainly.com/question/31321186
#SPJ1
if the amount of radioactive carbon 14 in a wooden artifact is only one- eighth of a new piece of the same wood, how old is the artifact?
The artifact is approximately 17,190 years old. The half-life of carbon-14 is approximately 5730 years. This means that the amount of carbon-14 in a sample will decrease by half every 5730 years.
If the amount of radioactive carbon-14 in a wooden artifact is one-eighth of a new piece of the same wood, then the fraction of carbon-14 remaining after some number of half-lives (n) can be calculated as:
(1/2)^n = 1/8
Simplifying this equation:
2^n = 8
2^n = 2^3
n = 3
This means that the wooden artifact has gone through 3 half-lives of carbon-14. The age of the artifact can be calculated by multiplying the half-life by the number of half-lives:
Age = Half-life × Number of half-lives
Age = 5730 years × 3
Age = 17,190 years
Find out more about the radioactive carbon 14
brainly.com/question/14812944
#SPJ4
a mixture of helium and hydrogen gases contains helium at a partial pressure of 428 mm hg and hydrogen at a partial pressure of 193 mm hg. what is the mole fraction of each gas in the mixture?
6.88 moles of helium and 3.12 moles of hydrogen are present in every 10 moles of gas in the combination.
The total pressure of the gas mixture can be found by adding the partial pressures of each gas:
Total pressure = partial pressure of helium + partial pressure of hydrogen
Total pressure = 428 mmHg + 193 mmHg
Total pressure = 621 mmHg
To find the mole fraction of each gas, we need to use the following formula:
Mole fraction = moles of gas / total moles of gas
We can find the moles of each gas using the ideal gas law:
PV = nRT
where P is pressure, V is volume, n is the number of moles, R is the gas constant, and T is temperature.
We can assume that the volume, temperature, and gas constant are constant, so we can simplify the equation to:
n = PV / RT
For helium:
n(He) = (428 mmHg)(V) / (R)(T)
For hydrogen:
n(H₂) = (193 mmHg)(V) / (R)(T)
The total number of moles of gas in the mixture is the sum of the moles of helium and hydrogen:
n(total) = n(He) + n(H₂)
To find the mole fraction of each gas, we can substitute the expressions for n(He), n(H₂), and n(total) into the formula:
Mole fraction of helium = n(He) / n(total)
Mole fraction of hydrogen = n(H₂) / n(total)
After simplifying and substituting the expressions, we get:
Mole fraction of helium = 0.688
Mole fraction of hydrogen = 0.312
Therefore, the mole fraction of helium in the mixture is 0.688 and the mole fraction of hydrogen is 0.312. This indicates that for every 10 moles of gas in the combination, 6.88 moles are helium and 3.12 moles are hydrogen.
To know more about the Mole fraction, here
https://brainly.com/question/29808190
#SPJ4
shown below is a dipeptide. a. over which ph range will the dipeptide predominantly exist as a neutrally charged molecule? b. what is the isoelectric point of this peptide? show your calculations to support your answer.
a. The two functional groups in an amino acid are the amino group (-NH2) and the carboxylic acid group (-COOH). When two amino acids join together via a peptide bond, the resulting dipeptide has two functional groups, one amino group and one carboxylic acid group, that can be ionized depending on the pH of the solution.
The pH at which a dipeptide predominantly exists as a neutrally charged molecule is the average of the two pKa values of its constituent amino acids. In this case, one amino acid has a pKa of 2.34 for the carboxylic acid group and a pKa of 9.60 for the amino group, while the other amino acid has a pKa of 2.20 for the carboxylic acid group and a pKa of 9.13 for the amino group.
To determine the pH range over which the dipeptide predominantly exists as a neutrally charged molecule, we need to find the average of the two pKa values for each functional group.
For the carboxylic acid group:
(pKa1 + pKa2) / 2 = (2.34 + 2.20) / 2 = 2.27
For the amino group:
(pKa1 + pKa2) / 2 = (9.60 + 9.13) / 2 = 9.37
Therefore, the pH range over which the dipeptide predominantly exists as a neutrally charged molecule is around pH 2.27 to pH 9.37.
b. The isoelectric point (pI) of a peptide is the pH at which it has a net charge of zero. To calculate the pI of this dipeptide, we need to find the pH at which the positive and negative charges on the dipeptide are equal.
At a pH below the pKa of the carboxylic acid group, the carboxylic acid group is protonated and carries a positive charge, while the amino group is protonated and carries a positive charge. At a pH above the pKa of the amino group, the amino group is deprotonated and carries a negative charge, while the carboxylic acid group is deprotonated and carries a negative charge.
Therefore, the pI can be calculated by averaging the two pKa values of the amino acids, as well as their corresponding charges.
pI = (pKa1 + pKa2) / 2 = (2.34 + 2.20 + 9.60 + 9.13) / 4 = 5.32
The isoelectric point of this dipeptide is 5.32.
To know more about dipeptide reactions, visit the link given below:
https://brainly.com/question/6194023
#SPJ4
Did aqueous methanol, CH3OH, have the same conductivity value as aqueous ethylene glycol, C2H6O2? Explain.
No, aqueous ethylene glycol and methanol don't have the same conductivity level.
What is aqueous methanol?When methanol (CH3OH) is dissolved in water, the term "aqueous methanol" is used (H2O). Due to the polarity of the molecules, methanol and water combine to form a homogeneous solution.
The concentration and mobility of the ions present in a solution determine its electrical conductivity. Although methanol (CH3OH) is a polar molecule, when it dissolves in water, it does not separate into ions. As a result of the lack of charged particles that can conduct an electric current, aqueous methanol has a low electrical conductivity.
The bigger molecule ethylene glycol (C2H6O2), in contrast, does dissociate into ions when it is dissolved in water, resulting in two charged particles for each molecule. As a result, aqueous ethylene glycol conducts electricity better than aqueous methanol.
As a result of the different numbers of ions created when methanol and ethylene glycol are dissolved in water, their conductivity values are different.
To know more about aqueous methanol, visit
brainly.com/question/30137922
#SPJ1
Write your own paragraph to reflect over the current situation of coral reefs and how these events can affect ocean health.
(If you intend to use any information from a source which you consider is of importance or can enrich or support your ideas you can use references or use citations- remember plagiarism is not acceptable)
The "rainforests of the sea," or coral reefs, are under serious threat from human activity and climate change. Overfishing, pollution, acidification of the water, and rising sea temperatures are all factors in the decline of coral reefs.
Coral reefs are important for the health of our oceans because they provide vital habitats for numerous fish species and other marine life. By absorbing wave energy, they also offer coastal security, reducing erosion and storm damage.
In addition to endangering the survival of numerous marine species, the destruction of coral reefs has serious economic repercussions for the local populations that depend on them for tourism and fishing.
Coral reef degradation is also a result of overfishing and pollution, such as nutrient runoff from farmland and sewage. Coral reef destruction threatens not only the biodiversity of our oceans but also the economies of the local communities that depend on them for tourists and fishing.
As a result, we must take action to lower our carbon emissions, enhance marine conservation efforts, and deal with the underlying reasons for the decline of coral reefs.
learn more about coral reefs here
https://brainly.com/question/10970167
#SPJ1
how does electronic polarizability or scaled-charge affect the interfacial properties of room temperature ionic liquids?
Electronic polarizability and scaled-charge are important parameters that can have a significant impact on the interfacial properties of RTILs, as well as their behavior in the presence of external electric fields.
Electronic polarizability is a measure of how easily the electron cloud in an atom or molecule can be distorted by an external electric field. In RTILs, electronic polarizability affects the strength of the electrostatic interactions between ions at the interface. This, in turn, affects the interfacial tension, which is a measure of the energy required to create new interfacial area between two immiscible phases.
Scaled-charge is a parameter that describes the effective charge of an ion in a RTIL. It takes into account the polarization of the ion's electron cloud in the presence of other ions in the RTIL. Scaled-charge affects the distribution of ions at the interface, as well as the surface charge density. This, in turn, affects the interfacial tension and the capacitance of the interface.
To know more about polarizability here
https://brainly.com/question/29765380
#SPJ4
in which pair do both compounds exhibit predominantly ionic bonding? group of answer choices naf and mgo so2 and hcl rbf and no2 kno3 and ch4 kcl and co2
The pair of compounds that exhibit predominantly ionic bonding are NaF and MgO.
NaF is composed of a metal (Na) and a non-metal (F), and MgO is composed of a metal (Mg) and a non-metal (O). In both compounds, the metal atom loses electrons to form a cation, and the non-metal atom gains electrons to form an anion. The resulting ions attract each other electrostatically to form the ionic bond.
In the other pairs of compounds listed, the bonds are not purely ionic. SO2 and HCl have covalent bonds, RbF and NO2 have polar covalent bonds, KNO3 has both ionic and covalent bonds, and KCl and CO2 have polar covalent bonds.
learn more about ionic bonding here : brainly.com/question/957239
#SPJ4
You have a 0.05 M solution of sulfuric acid. What is the concentration in grams per liter (or dm3)?
The sulfuric acid solution has a concentration of 4.904 grams per liter (or dm3).
What is sulphuric acid?With the chemical formula H₂SO₄, sulfuric acid is a potent, colorless, odorless, and extremely corrosive mineral acid. It is also referred to as "vitriol oil." An extremely significant industrial chemical, sulfuric acid is used to make a variety of goods, including fertilizers, detergents, pigments, dyes, medicines, and explosives.
The formula below can be used to get the molar mass of sulfuric acid (H₂SO₄):
H₂SO₄'s molar mass is calculated as follows: 2 × (1.008 g/mol) + 32.06 g/mol + 4(16.00 g/mol) = 98.08 g/mol.
Hence, 98.08 g equals one mole of sulfuric acid.
We must multiply the molarity by the sulfuric acid's molar mass in order to translate the molarity (0.05 M) to grams per liter:
4.904 g/L = 0.05 mol/L x 98.08 g/mol
As a result, the sulfuric acid solution has a concentration of 4.904 grams per liter (or dm³).
To know more about sulphuric acid, visit:
brainly.com/question/12986533
#SPJ1
why do you discard solutions containing hexane in the separatory funnel instead of the organic waste container?
Always discard solutions containing hexane in a designated organic waste container to ensure safety, environmental responsibility, and compliance with regulations.
When using a separatory funnel to separate an organic solvent like hexane from an aqueous solution, it's important to discard the hexane properly to ensure safety and environmental responsibility. You should discard solutions containing hexane in a designated organic waste container instead of the general waste container because:
1. Safety: Hexane is a volatile and flammable solvent. Disposing of it in a general waste container could create a fire hazard or cause harmful fumes to accumulate.
2. Environmental responsibility: Hexane is harmful to the environment if not disposed of correctly. Designated organic waste containers are meant for solvents like hexane, so they are properly treated and managed to minimize environmental impact.
3. Compliance with regulations: Laboratory regulations often require that different types of waste be disposed of separately to ensure proper handling and treatment. Discarding hexane in the appropriate organic the waste container ensures compliance with these regulations.
For more such questions on hexane
brainly.com/question/9630611
#SPJ11
what is the number of formula units in a 1.86 mol sample of fecl3?
The number of formula units in a 1.86 mol sample of FeCl3 is 1.12 × 10²⁴.
Formula units are defined as the smallest repeating unit in an ionic compound.
They can be atoms, ions, or molecules depending on the type of compound. In order to find the number of formula units in a given amount of a substance, we need to use Avogadro's number, which is the number of particles in one mole of a substance (6.022 × 10²³ particles/mole).
To find the number of formula units in a 1.86 mol sample of FeCl3, we need to first determine the formula unit for FeCl3. The formula for FeCl3 is FeCl3, which means there is one iron atom and three chlorine atoms in each formula unit.
Next, we need to use Avogadro's number to convert from moles to formula units.
We can do this by multiplying the number of moles by Avogadro's number. 1.86 mol × 6.022 × 10²³ formula units/mole = 1.12 × 10²⁴ formula units.
Therefore, there are 1.12 × 10²⁴ formula units in a 1.86 mol sample of FeCl3.
To know more about FeCl3 refer to-
brainly.com/question/8203381#
#SPJ11
d
5 Aluminium and iron oxide (Fe₂O3) react together to produce aluminium oxide
(Al2O3). The equation for the reaction is:
Tran oxid
2:2
241+Fe2O3Al2O3+2Fe
Relative atomic masses (A): Al = 27,0=16, Fe=56.
Calculate the mass of iron that is produced by reacting 20 g of iron oxide with
an excess of aluminium.
Maths skills links
You may also need to convert the mass of a substance into an amount in moles
(and vice versa) when using moles to balance equations.
Aluminum and iron oxide (Fe₂O₃) react together to produce aluminum oxide, 20 g of Fe₂O3 will produce 14 g of Fe.
What is meant by oxide?Oxide is a category of chemical compound that has one or more oxygen atoms and also another element in its composition.
2Al + Fe₂O₃ -> Al₂O₃ + 2Fe
Molar mass of Fe₂O₃ is: (2 x 56) + (3 x 16) = 160 g/mol
moles of Fe2O3 = 20 g / 160 g/mol = 0.125 mol
As the reaction is carried out with an excess of Al, we can assume that all of the Fe₂O₃ is consumed and that 2 moles of Fe are produced for every mole of Fe₂O₃
moles of Fe = 2 x moles of Fe₂O₃ = 0.25 mol
Molar mass of Fe is : 56 g/mol
So the mass of Fe produced is:
mass of Fe = moles of Fe x molar mass of Fe
mass of Fe = 0.25 mol x 56 g/mol = 14 g
Therefore, 20 g of Fe₂O₃ will produce 14 g of Fe.
To know more about oxides, refer
https://brainly.com/question/30368235
#SPJ1
ammonia nh3 is generally considered a basic compound, but under very basic conditions it can act as an acid. what is the chemical formula for the conjugate base of nh3?
The conjugate acid of ammonia under the basic conditions is given as NH⁴⁺ (Ammonium).
Acid-base pairs that differ by one proton are called conjugated pairs. A conjugate acid-base pair is a pair of substances that can both absorb hydrogen ions and donate hydrogen ions to each other. A proton is added to a compound to create a conjugate acid, and a proton is removed to create a conjugate base. The conjugate acid of ammonia
NH3 is NH₃ + H⁺ → NH₄⁺, where NH3 is the conjugate base and NH4+ is the conjugate acid. NH3 is generally considered a basic chemical, but it can act as an acid under extremely alkaline conditions.
To know more about conjugate acid, visit,
https://brainly.com/question/12584785
#SPJ4
the graph below shows the titration curve that results when 100. ml of 0.0250 m acetic acid is titrated with 0.100 m naoh. what part of the curve corresponds to the optimum buffer action for the acetic acid/acetate ion pair?
The buffer region of a titration curve corresponds to the portion where there is a relatively flat or gradual slope in the curve. This occurs when there is a significant amount of both the weak acid and its conjugate base present in the solution.
Titration is a common technique used in chemistry to determine the concentration of a solution, or to find the amount of a substance in a solution. It involves adding a solution of known concentration (the titrant) to a solution of unknown concentration (the analyte) until the reaction between the two is complete. The factor at which the response is entire is referred to as the endpoint, and it is usually detected by way of using a trademark that changes shade when the response is finished.
Titration is an effective device for figuring out the concentration of a wide variety of substances, including acids, bases, and various other chemical substances. It is widely used in many areas of chemistry, including analytical, environmental, and industrial chemistry. Titration can be used to determine the concentration of a particular substance in a solution, or to determine the purity of a sample. It is an essential technique for many industries, including pharmaceuticals, food and beverage production, and water treatment.
To learn more about Titration visit here:
brainly.com/question/2728613
#SPJ4
click reset.this time, decrease the setting on the dial as you get close to the melting point. notice that melting occurs over a range of temperatures. can you determine the exact range of temperatures over which melting occurs? (this may take several tries, be patient.) what is thetemperaturerangeover which melting occurs?
The melting point is the temperature at which solid changes into a liquid. It is a characteristic property of a substance and can be used to identify or characterize it.
The melting point depends on the strength of the intermolecular forces between the molecules of the substance. Stronger intermolecular forces result in higher melting points.
To measure the melting point of a substance, you need to heat it gradually and monitor its temperature and physical state. You can use a device called a melting point apparatus, which consists of a heating block, a thermometer, and a capillary tube. You place a small amount of the substance in the capillary tube and insert it into the heating block. You then adjust the heating rate and observe when the substance starts to melt and when it completely melts. The temperature range over which melting occurs is called the melting point range.
The melting point range can vary depending on several factors, such as the purity of the substance, the heating rate, and the accuracy of the thermometer. A pure substance usually has a sharp melting point, meaning that it melts within a narrow temperature range (usually less than 1°C). An impure substance usually has a broad melting point, meaning that it melts over a wide temperature range (usually more than 1°C). A faster heating rate can cause the temperature to rise faster than the substance can melt, resulting in a higher apparent melting point. A slower heating rate can allow the substance to melt more evenly, resulting in a lower apparent melting point. A faulty or imprecise thermometer can also affect the accuracy of the melting point measurement.
Therefore, to determine the exact range of temperatures over which melting occurs for a given substance, you need to use a pure sample, a reliable thermometer, and an optimal heating rate. You also need to repeat the measurement several times and take an average of your results. You may also compare your results with literature values or known standards to verify your accuracy.
to know more about melting points click here:
https://brainly.com/question/40140
#SPJ4
determine how the ph of the following three solutions will change when 50 ml of h 2 o is added separately to each of them. i. 50 ml of 0.02 m kcl(aq) ii. 50 ml of 0.02 m hcl(aq) iii. 50 ml of 0.02 m koh(aq) 50 ml of 0.02 m kcl(aq) 50 ml of 0.02 m hcl(aq) 50 ml of 0.02 m koh(aq) a. ph increases ph increases ph increases b. no change in ph ph increases ph decreases c. no change in ph ph decreases ph increases d. ph decreases ph increases ph decreases e. ph decreases ph decreases ph decreases
In 50 mL of 0.02 M KCl(aq) solution there is no change n pH. Option C is correct, In 50 mL of 0.02 M HCl(aq) solution Ph will increases. Option A is correct, and in 50 mL of 0.02 M KOH(aq) solution Ph will decreases. OPtion D is correct.
The pH of each solution will change differently upon addition of 50 mL of water, depending on the properties of the original solutions. Here are the changes will occur.
50 mL of 0.02 M KCl(aq); Adding water to a salt solution will not change the pH, since salts do not react with water to produce acidic or basic solutions. Therefore, the pH of the solution will remain the same.
50 mL of 0.02 M HCl(aq); Adding water to an acidic solution will dilute the acid and decrease the concentration of H+ ions, causing the pH to increase. Therefore, the pH will increase.
50 mL of 0.02 M KOH(aq); Adding water to a basic solution will dilute the base and decrease the concentration of OH- ions, causing the pH to decrease. Therefore, the pH will decrease.
Hence, C. A. D. is the correct option.
To know more about salt solution here
https://brainly.com/question/11134365
#SPJ4
If 540 and forty wheels are delivered on Monday morning, how many handlebars would be need to manufacture all those tricycles?
540 handlebars
180 handlebars
270 handlebars
1,620 handlebars
Answer:
540
one for every tricycle2 NH3 + 3 CuO --> 3 Cu + N2 + 3 H2O
In the above equation how many moles of N2 can be made when 166.8 grams of CuO are consumed?
Round your answer to the nearest tenth. If you answer is a whole number like 4, report the answer as 4.0
Use the following molar masses. If you do not use these masses, the computer will mark your answer incorrect.:
Element
Molar Mass
Hydrogen
1
Nitrogen
14
Copper
63.5
Oxygen
16
2. For the reaction C + 2H2 → CH4, how many moles of carbon are needed to make 174.6 grams of methane, CH4 ?
Round your answer to the nearest tenth. If you answer is a whole number like 4, report the answer as 4.0
Use the following molar masses. If you do not use these masses, the computer will mark your answer incorrect.:
Element
Molar Mass
Hydrogen
1
Carbon
12
3. 3 Cu + 8HNO3 --> 3 Cu(NO3)2 + 2 NO + 4 H2O
In the above equation how many moles of water can be made when 110.2 grams of HNO3 are consumed?
Round your answer to the nearest tenth. If you answer is a whole number like 4, report the answer as 4.0
Use the following molar masses. If you do not use these masses, the computer will mark your answer incorrect.:
Element
Molar Mass
Hydrogen
1
Nitrogen
14
Copper
63.5
Oxygen
16
The amount of nitrogen in moles (n) is [n=166.8.028.0] = 5.95714286 moles. every mole of CH4 is consumed results in the production of one mole of CO2. In 100 g of water, there are about eleven moles of hydrogen atoms.
when 100 moles of water are present?Under a consistent pressure of 1 atm, a mole of water heated to 100°C turns into steam. [Heat of vaporisation liquid water at 100°C= 540cal/gm] is the change in entropy.
How many mole of CH4 must be burned in order to produce 44g of CO2?Since 1 mole or methane can completely burn to make 1 mole of carbon dioxide, we may say that mole ratio of methane can fully burn to produce 44 grammes of carbon dioxide.
To know more about atoms visit:
https://brainly.com/question/30898688
#SPJ1
the total pressure of a gas mixture is equal to the sum of the pressures that each gas would exert independently. this law of partial pressure is referred to as
Dalton's law of partial pressure means that the total pressure of a gas mixture is equal to the sum of the individual partial pressures of each gas.
Partial pressure is defined as the pressure at which all gases would escape if the gases were in the volume of the mixture at the same temperature. The total pressure of the oil mixture is equal to a fraction of the different oil. The total pressure P (total) is the sum of all the stresses present in the reference material. Dalton's law of partial pressure states that the total pressure of a gas mixture is equal to the partial pressure of the component gas. Mathematically expression : [tex]P = \sum P_i = P_1 + P_2 + .... [/tex]
where, P --> total pressure
Pi --> partial pressures of each gas
The desired answer is therefore Dalton's partial pressure law.
For more information about Dalton's law of partial pressures, visit :
https://brainly.com/question/13082853
#SPJ4
What cellular process occurs in the uterus before differentiation?
In the uterus, the fertilised egg or zygote passes through a number of cellular processes. Cell division, in which the zygote divides multiple times to create a mass of cells known as a blastocyst, is one of the most crucial processes.
What is the embryo's first step of cellular differentiation?Identity of cells, tissues, organs, and organisms are determined by the division of cells during embryogenesis. A embryo is created after a sperm fertilises an egg. The embryonic differentiation process begins when the zygote undergoes cleavage, a division into numerous cells.
Cellular division starts at what point?When separate tissue layers first form during a process known as gastrulation in vertebrates, differentiation starts. The regulation of differentiation by genes is similar to that of most other developmental processes.
To know more about cellular processes visit:-
https://brainly.com/question/17772081
#SPJ9
PLEASE HELP!!! 4. If excess nitric acid acid reacts with 25.4 g of lithium bromide, how many
grams of hydrobromic acid are produced?
HNO3(aq) + LiBr(a) → LINO3(aq) + HBr(ag)
The correct answer is To determine how many grams of hydrobromic acid (HBr) are produced when excess nitric acid[tex](HNO3)[/tex]reacts with 25.4 g of lithium bromide[tex](LiBr)[/tex], we need to use stoichiometry and the balanced chemical equation provided.
The balanced chemical equation is [tex]HNO3(aq) + LiBr(aq) → LiNO3(aq) + HBr(aq)[/tex]From the equation, we can see that one mole of HNO3 reacts with one mole of LiBr to produce one mole of HBr. Therefore, we need to first determine the number of moles of LiBr used in the reaction. To do this, we can use the molar mass of LiBr to convert the given mass of 25.4 g to moles: [tex]25.4 g LiBr x (1 mole LiBr / 86.85 g LiBr) = 0.292 moles LiBr[/tex]Since the reaction uses 1 mole of LiBr, we know that 0.292 moles of HBr will be produced. To determine the mass of HBr produced, we can use the molar mass of HBr: [tex]0.292 moles HBr x (80.91 g HBr / 1 mole HBr) = 23.6 g HBr[/tex] Therefore, when excess nitric acid reacts with 25.4 g of lithium bromide, 23.6 g of hydrobromic acid are produced. It's important to note that the word "excess" indicates that there is more than enough nitric acid to react with all of the lithium bromide, which means that the reaction will go to completion and all of the LiBr will be consumed. If the nitric acid were limiting, then we would need to calculate the amount of HBr produced based on the limiting reactant.
To learn more about stoichiometry click on the link below:
brainly.com/question/30215297
#SPJ1
when a high energy electron impact molecule m in the ionization chamber what type of species is initally produced
A radical cation is created in the ionization chamber when a high energy electron impacts molecule M.
In an ionization chamber, a high energy electron can form a variety of species, such as electrons, ions, and neutral species, when it collides with the molecule "m." Ion pairs, which are composed of a negatively charged electron and a positively charged ion (cation), are the most prevalent species (anion).
This is due to the tremendous energy of the hitting electron, which can knock an electron out of the molecule and leave a positively charged ion (cation) in its place. In order to determine the energy and intensity of the electron beam in the ionization chamber, the generated ion pair is then detected.
Instruments that measure and detect ionizing radiation are called ionization chambers. Ionizing radiation is used to produce charged particles, usually ion pairs, inside the chamber.
To know about ionization
https://brainly.com/question/1602374
#SPJ4
The complete question is
When high energy electron impacts molecule M in the ionization chamber, what type of species initially produced?
what is the concentration (in m) of ions, in a solution of 0.584 moles of cacl2 dissolved in enough water to make 4.76 l of the solution?
Answer:
Explanation:
Calcium chloride (CaCl2) dissociates into three ions in water: one Ca2+ ion and two Cl- ions.
To find the concentration of ions in the solution, we need to find the total number of moles of ions that result from dissolving 0.584 moles of CaCl2:
One mole of CaCl2 produces one mole of Ca2+ ions and two moles of Cl- ions.
Therefore, 0.584 moles of CaCl2 produces 0.584 moles of Ca2+ ions and 2 x 0.584 = 1.168 moles of Cl- ions.
Next, we need to find the total volume of the solution:
The solution is made by dissolving the CaCl2 in enough water to make 4.76 L of solution.
Therefore, the volume of the solution is 4.76 L.
Finally, we can calculate the concentration of each ion:
Concentration of Ca2+ ions: moles of Ca2+ ions / volume of solution = 0.584 mol / 4.76 L = 0.122 M
Concentration of Cl- ions: moles of Cl- ions / volume of solution = 1.168 mol / 4.76 L = 0.245 M
So the concentration of Ca2+ ions is 0.122 M and the concentration of Cl- ions is 0.245 M.
The concentration (in m) of ions, in a solution of 0.584 moles of CaCl2 dissolved in enough water to make 4.76 L of the solution is 0.245 M.
What is concentration?
Concentration refers to the amount of a substance that is dissolved in a specific quantity of solvent or solution. It is typically measured in units of moles per liter (M) or milligrams per deciliter (mg/dL).
What is CaCl2?
Calcium chloride (CaCl2) is a compound of calcium and chlorine. It is a salt that is commonly used as a drying agent, because it can absorb water from the air. It is also used in food preservation, snow and ice removal, and concrete mixing.
How to find the concentration of CaCl2 ions?
The molar mass of CaCl2 is 111 g/mol.
Number of moles of CaCl2 = mass/molar mass= 0.584 moles
Volume of the solution = 4.76 L.
The concentration of CaCl2 ions can be calculated as follows:
Concentration of CaCl2 = Number of moles of CaCl2/Volume of the solution= 0.584 moles/4.76 L= 0.1227 M
The concentration of ions, on the other hand, is calculated as twice the concentration of CaCl2 because the compound dissociates into two ions: Ca2+ and 2Cl-.
Therefore, the concentration of ions = 2 × 0.1227 M= 0.245 M.
Therefore, the concentration (in m) of ions, in a solution of 0.584 moles of CaCl2 dissolved in enough water to make 4.76 L of the solution is 0.245 M.
To know more about concentration click here:
brainly.com/question/30862330
#SPJ11
7. a sample of 0.10 m c6 h5 cooh(aq) (benzoic acid) solution is titrated with 0.10 m naoh(aq) solution. what is the ph of the solution at the equivalence point? ka (c6 h5 cooh)
The pH of the solution at the equivalence point is 4.19.
To calculate the pH at the equivalence point of the titration, we need to use the Henderson-Hasselbalch equation:
[tex]pH=pKa+log(\frac{A^{-} }{HA} )[/tex]
At the equivalence point, the moles of C6H5COOH and NaOH will be equal, so the concentration of C6H5COOH will be halved, and the concentration of its conjugate base, C6H5COO-, will be equal to the concentration of NaOH added. Therefore, we can substitute [A-] with the concentration of NaOH.
0.10 M NaOH will be added to 0.05 M of C₆H₅COOH to reach the equivalence point. We can then use the Ka value to calculate the pKa:
pKa = -㏒(Ka) = -㏒(6.5 x 10⁻⁵)
= 4.19
Substituting the values into the Henderson-Hasselbalch equation:
pH = 4.19 + ㏒([NaOH]/[C₆H₅COOH])
At the equivalence point,
[NaOH] = 0.05 M and [C₆H₅COOH] = 0.05 M.
Substituting these values:
pH = 4.19 + log(1)
= 4.19
As a result, the solution's pH at the equivalence point is 4.19.
To know more about the Equivalence point, here
https://brainly.com/question/11004927
#SPJ4
which of the following reaction types best represent the following reaction?fe subscript 2 straight o subscript 3 space (s )plus 3 space co space (g )rightwards arrow 2 space fe space (s )plus 3 space co subscript 2 space (g )
The oxidation number of iron(Fe) decreases from +3 to 0. The oxidation number of C increases from +2 to +4. Hence Fe2O3 is reduced and CO is oxidized. Hence, it is a redox reaction.
One of the reactants in a redox reaction involving two reactants will be an oxidising agent, and the other reactant will be a reducing agent. By taking electrons, the oxidising agent reduces while aiding in the oxidation of other species. By contributing electrons and undergoing oxidation, the reducing agent aids in the reduction of other species.
The species that experience a rise in oxidation state is the reducing agent in a redox reaction, while the species that experience a reduction in oxidation state is the oxidising agent. In this reaction Carbon monoxide(CO) is the reducing agent and it has reduced ferric oxide Fe2O3 which acts as an oxidizing agent.
Learn more about Redox reaction, here:
https://brainly.com/question/21851295
#SPJ4
What is the volume, measured in liters at STP, of 285 grams of the gas acetylene, C3H8?
Answer:
a
Explanation:
What is the volume, measured in liters at STP, of 285 grams of the gas acetylene, C3H8? which equals 67-4o92- witch then gives u a
what is the buffer component ratio, (ch3coo-)/(ch3cooh) of an acetate buffer that has a ph of 4.47. ka of ch3cooh is 1.8 x 10-5.
The buffer component ratio, (CH3COO-)/(CH3COOH), of an acetate buffer with a pH of 4.47 and a Ka of CH3COOH of 1.8 x 10^- is: 0.54
The buffer component ratio, (CH3COO-)/(CH3COOH), of an acetate buffer with a pH of 4.47 and a Ka of CH3COOH of 1.8 x 10^-5 can be calculated using the Henderson-Hasselbalch equation:
pH = pKa + log([CH3COO-]/[CH3COOH])
So, the buffer component ratio (CH3COO-)/(CH3COOH) of the acetate buffer is approximately 0.54.
To know more about "Henderson-Hasselbalch equation" refer here:
https://brainly.com/question/13423434#
#SPJ11
which state of matter has the weakest intermolecular forces? select the correct answer below: gas liquid solid all states of matter have the same strength of intermolecular forces.
The state of matter that has the weakest intermolecular forces is the gas state. Option A is correct.
In the gas state, the molecules are relatively far apart from each other and are in constant motion. The intermolecular forces between gas molecules are weak because the molecules have a large separation distance, resulting in a low density and high compressibility. The kinetic energy of gas molecules is much greater than the strength of their intermolecular forces, and they tend to move independently of each other.
In contrast, in the liquid and solid states, the intermolecular forces are stronger due to the closer proximity of the molecules. In liquids, the molecules are in close contact with each other, allowing for the formation of temporary dipole-dipole forces and hydrogen bonding. In solids, the molecules are held together by even stronger forces, such as ionic, covalent, or metallic bonds. Option A is correct.
Which state of matter has the weakest intermolecular forces?
Select the correct answer below:
A. Gas
B. Liquid
C. Solid
D. All states of matter have the same strength of intermolecular forces.
To know more about the Forces, here
https://brainly.com/question/30644583
#SPJ4
what is the solubility in moles/liter for copper(ii) oxalate at 25 oc given a ksp value of 2.9 x 10-8. write using scientific notation and use 1 or 2 decimal places (even though this is strictly incorrect!)
The solubility of copper(II) oxalate at 25°C is approximately 5.39 x 10^-5 moles/liter.
To determine the solubility of copper(II) oxalate (CuC2O4) in moles/liter, we can use the Ksp value.
The balanced dissociation equation for CuC2O4 is:
[tex]CuC2O4 (s) ⇌ Cu²⁺ (aq) + C2O4²⁻ (aq)[/tex]
Let 's' represent the solubility of CuC2O4 in moles/liter. At equilibrium, the concentrations of Cu²⁺ and C2O4²⁻ ions are both 's' moles/liter.
The Ksp expression for CuC2O4 is:
[tex]Ksp = [Cu²⁺] * [C2O4²⁻][/tex]
Given that Ksp is[tex]2.9 x 10^-8:[/tex]
[tex]2.9 x 10^-8 = (s) * (s)[/tex]
To find 's', we can solve the equation:
[tex]s² = 2.9 x 10^-8[/tex]
[tex]s = √(2.9 x 10^-8)[/tex]
[tex]s ≈ 5.39 x 10^-5 moles/liter[/tex]
to know more about solubility refer here:
https://brainly.com/question/28170449#
#SPJ11