how much work is required to move it at constant speed 5 m along the floor against a frition force of 350 n

(a) The decrease in internal energy of the woman, assuming no change in temperature or consumption of food is -9600 J (negative because energy is lost) and (b) her efficiency is 3.64%.

The woman does 350 J of work and 9250 J of heat is transferred from her into the environment in the process. Since the energy transferred as heat is not positive, it is not useful energy. It is energy that is not doing any work. Therefore, the total energy transferred from the woman is 9250 J (as heat).

(a) The decrease in internal energy of the woman, assuming no change in temperature or consumption of food is the sum of the energy transferred as heat and the energy used to do work.

[tex]\Delta U=Q-W[/tex]

where ΔU is the change in internal energy, Q is the heat added to the system, and W is the work done by the system. Since no heat is added to the system,

[tex]\Delta U=-W = -350 \ J - 9250\  J = -9600 \ J[/tex] (negative because energy is lost).

(b) The efficiency of a machine is defined as the ratio of useful work done by the machine to the total energy input. In this case, the woman is the machine.

Efficiency = Useful work output / Total energy input

Total energy input = energy transferred as heat + energy used to do work [tex]= 9250 \ J + 350 \ J = 9600 \ J[/tex]

Useful work output = Work done = 350 J

Therefore, the efficiency of the woman is

Efficiency = Useful work output / Total energy input

Efficiency [tex]= 350\  J / 9600\  J\times 100 = 0.0364\times 100 = 3.64%[/tex].

Learn more about efficiency:

https://brainly.com/question/3617034

#SPJ11

If the colours at the base of the leaves appear distortion, there may be a number of causes including poor lighting, the age of the leaves, a lack of nutrients, a disease or pest infestation, or even a genetic mutation in the plant.

Dispersion is the distribution of white light throughout its entire spectrum of wavelengths. The dispersion of sunlight into a continuous range of colours causes rainbows, which are created by a combination of refraction and reflection.

The prism separates the white light into its individual colors, which are red, orange, yellow, green, blue, and violet.

To know more about prism visit:-

https://brainly.com/question/10462991

#SPJ1

The maximum height H reached by the ball when the spring is compressed to its full extent is determined by the elastic potential energy stored in the spring, which is equal to the kinetic energy of the ball at the highest point of its trajectory. Therefore, we can write:

(1/2) k [tex]x^2[/tex] = m g H

where k is the spring constant, x is the compression distance of the spring, m is the mass of the ball, and g is the acceleration due to gravity.

When the spring is compressed to only half its full extent, the compression distance x is also halved, and the stored elastic potential energy becomes one-fourth of its original value. Since the mass and the acceleration due to gravity remain the same, we can write:

(1/2) k[tex](x/2)^2[/tex] = m g H'

where H' is the maximum height reached by the ball in the second shot.

Solving for H', we get:

H' = H/4

Therefore, the ball goes up to one-fourth of its maximum height in the second shot, which is equivalent to a height of H/4.

For more details about height click here:

https://brainly.com/question/10726356#

#SPJ11

The resistence of each resistor can be calculated by using the equation for resistors in series: R = Ps/I and the equation for resistors in parallel: R = Pp/I.

By substituting the given values for Ps, I and Pp into the equations, we get R1 = Ps/I and R2 = Pp/I. Thus, the value of each resistor can be determined by dividing the total power by the total current.

These equations are based on Ohm's law, which states that the voltage across a resistor is equal to the current through the resistor multiplied by the resistance. By connecting resistors in series or parallel, the overall resistance of the network can be calculated. Knowing the total power and total current, the individual resistances of each resistor can be determined.

Know more about Ohm's law here

https://brainly.com/question/1247379#

#SPJ11

The average force exerted on the bullet by the ammunition is 2434.2 N.

We can use the impulse-momentum theorem to determine the average force exerted on the bullet by the ammunition:

[tex]F_{avg} \times t = \Delta p[/tex]

where F_avg is the average force, t is the time over which the force is applied, and Δp is the change in momentum of the bullet. Since the bullet is fired from the muzzle of the rifle, we can assume that the time over which the force is applied is equal to the time it takes for the bullet to travel the length of the barrel:

t = L / v

where L is the length of the barrel and v is the velocity of the bullet.

Substituting L = 0.950 m and v = 555 m/s, we get:

t = 0.950 m / 555 m/s = 0.00171 s

The change in momentum of the bullet can be calculated as:

[tex]\Delta p = p_f - p_i[/tex]

where p_f is the final momentum of the bullet and p_i is its initial momentum. Since the bullet is fired from rest, its initial momentum is zero. The final momentum can be calculated using the formula:

p_f = m * v

where m is the mass of the bullet and v is its velocity. Substituting

m = 7.50 g = 0.00750 kg and v = 555 m/s, we get:

[tex]p_f = 0.00750 kg \times 555 \ m/s = 4.16\ kg m/s[/tex]

Therefore, the change in momentum of the bullet is:

[tex]\Delta p = p_f - p_i = 4.16\ kg m/s - 0 = 4.16 \ kg m/s[/tex]

Substituting t = 0.00171 s and Δp = 4.16 kg m/s into the expression for the average force, we get:

[tex]F_{avg} \times t = \Delta p[/tex]

[tex]F_{avg} = \Delta p / t = (4.16\ kg m/s) / (0.00171 s) = 2434.2\ N[/tex]

Therefore, the average force exerted on the bullet is 2434.3 N.

Learn more about force:

https://brainly.com/question/12785175

#SPJ11

According to the rules of continuity, if you are following a subject moving through space and the subject exits screen right (the right of the screen), they should enter the next shot from the left side of the screen. This is known as the 180-degree rule and is used to create a sense of spatial coherence between shots.

The 180-degree rule states that the camera should stay on one side of the action, meaning that a character's movement should remain consistent. To explain further, if a character is moving right, they should keep moving right as they move through the various shots. The same applies for movement left, up, and down. If a character moves off screen right, they should enter the next shot from the left. This creates a smooth and logical transition from shot to shot, which helps the audience understand the spatial relationship between characters.

In addition to the 180-degree rule, other aspects of continuity editing are used to create a cohesive narrative. Continuity editing includes matching eyelines (the direction a character is looking in a shot), matching facial expressions, and matching camera angles. All these elements, along with the 180-degree rule, help create a sense of continuity and flow between shots.

for such more question on continuity

https://brainly.com/question/24637240

#SPJ11

The statement "tides are caused by gravitational interactions between the earth, sun, and moon" is true.

Tides are defined as the rise and fall of sea levels caused by the combined effects of gravitational forces exerted by the Moon, Sun, and the rotation of the Earth. The Earth's water surface is continuously pulled towards the Moon, and this results in two bulges of water on opposite sides of the Earth, resulting in high tide.

On the other hand, low tide occurs between the two high tides, where the water level is at its lowest point. The Sun, even though it is 93 million miles away from the Earth, exerts a gravitational force on it. The gravitational force exerted by the Sun on the Earth is about 177 times weaker than that exerted by the Moon.

However, when the Sun, Earth, and the Moon line up, their combined gravitational force results in higher-than-normal tides called Spring Tides, and when they are at right angles to each other, they produce lower-than-normal tides called Neap Tides.

Therefore, Tides are caused by the gravitational pull of the sun and moon on the Earth's oceans, which creates a bulge of water that rises and falls twice a day.

To know more about high tides click here:

https://brainly.com/question/14683300

#SPJ11

The power contact lens which when on the eye will correct his distant vision is of -2.57 diopters

The man's far point measures 38.9 cm, which indicates that his eye's lens' focal length is also 38.9 cm. It is required to change the focal length of the lens to infinity to rectify his eyesight, which necessitates the addition of a negative power lens to his eye.

Calculating the power of contact lens

Power of contact lens = 1 / focal length of the lens

= 1 / focal length of the lens - 1 / desired focal length

In this case, the desired focal length is infinity.

Substituting the value -

= 1 / 0.389 - 1 / infinity

= -2.57

Read more about contact lens on:

https://brainly.com/question/10921004

#SPJ4

Yes, when a light ray enters from water to air, it will bend further from the normal. This phenomenon is known as refraction, and is caused by the difference in speed between light passing through the two different materials. The light ray will slow down when passing through water, so it will bend closer to the normal.

When a light ray enters the air from water, the light ray will refract closer to the normal. This is due to the fact that light travels faster through air than through water, so when the light enters the air, it bends towards the normal. The amount of refraction is determined by the index of refraction of each material. Since the index of refraction of air is lower than the index of refraction of water, the light ray will bend closer to the normal.

To better understand this, imagine a light ray traveling from a denser material (like water) to a less dense material (like air). As the light ray enters the air, the speed of the light increases, causing it to bend closer to the normal. This is due to the law of refraction, which states that the angle of refraction is inversely proportional to the speed of the light ray. In summary, when a light ray enters the air from water, it will refract closer to the normal. This is due to the fact that light travels faster through air than through water, so the light ray bends towards the normal. The amount of refraction is determined by the index of refraction of each material, with the lower index refraction material (air) resulting in the light ray bending closer to the normal.

For more questions related to refraction.

https://brainly.com/question/14760207

#SPJ11

The coefficient of static friction between the tires and the road if a car is to round a level curve of radius 145 m at a speed of 130 km/h is 4.64

Whenever the object rotаtes аround the curved pаth then а net force аcts on the object pointing towаrds the center of а circulаr pаth аnd it is cаlled а centripetаl force. Mаthemаticаlly, we cаn write;

Centripetаl Force = [tex]\frac{mv^{2} }{r}[/tex]

where m is the mass of the body, v is the velocity of the body, and r is the radius of rotation.

We are given:

Since the car is making circular motion, therefore, necessary centripetal force is provided by the frictional force.

frictional force = centripetal force

μsmg = [tex]\frac{mv^{2} }{r}[/tex]

μs = [tex]\frac{v^{2} }{rg}[/tex]

μs = [tex]\frac{81.25^{2} }{145.9.81}[/tex]

μs = 4.64

Therefore, the coefficient of static friction between the tires of the car and the road surface is 4.64.

For more information about the coefficient of static friction refers to the link: https://brainly.com/question/13828735

#SPJ11

Using the above values for the speed of sound and wavelength, the frequency of the sound produced by the bird in the tree is determined to be 14.7 Hz. A typical person is unlikely to be able to hear this sound.

As with all waves, the relationship between the frequency and wavelength of sound is and its wavelength.

The following equation can be used to calculate sound intensity: P stands for pressure change or amplitude, D stands for material density, and VW stands for measured sound speed. The more your sound wave oscillates, the louder your sound will be.

To know more about wavelength visit:-

https://brainly.com/question/13533093

#SPJ9

Each charge has a magnitude of about 1.3×C (to two significant numbers), or 13 C.

To find the magnitude of each charge, we can rearrange Coulomb's law as follows:

Coulomb's law: F = k * |q1 * q2| / r²

Here, F is the force between two charges (16 N), k is Coulomb's constant (8.99 × 10⁹ N·m²/C²), q1 and q2 are the magnitudes of the two charges, and r is the distance between the charges (5.0 cm or 0.050 m). Since the charges have equal magnitude, we can say q1 = q2 = q.

Rearranging the formula for q:

q² = F * r² / k

Now, we can plug in the given values and solve for q:

q² = (16 N) * (0.050m)² / (8.99 × 10⁹ N·m²/C²)

q²≈ 1.77 × 10⁹ C²

q ≈ √(1.77 ×10⁹ C²)

q ≈ 1.33 × 10⁵C

So, the magnitude of each charge is approximately 1.3 ×10⁵ C (to two significant figures) or 13 μC.

To know more about magnitude click on below link :

https://brainly.com/question/14452091#

#SPJ11

The distance from the earthquake epicenter to the seismic station is 25.74 km.

S and P waves are two of the three major seismic waves that travel through the Earth as a result of an earthquake. An earthquake's seismic waves are used by seismologists to map the Earth's interior. The speed of an S wave is slower than that of a P wave, but it can still cause significant damage. The distance from the earthquake epicenter to the seismic station is calculated using the time difference between the P wave's arrival and the S wave's arrival. The following is how to find the distance.

Difference in Time= 17.3 seconds

Speed of S wave= 4.50 km/s

Speed of P wave= 7.80 km/s

Let the distance from the earthquake epicenter to the seismic station be 'x'.

Using the time and speed values, we can set up the following equations for the distance:

Distance traveled by the P wave= Speed × Time taken

x = 7.80 × t

Distance traveled by the S wave= Speed × Time taken

d = 4.50 × t

The difference between the two equations is:

x - d = 17.3 seconds

Solving for 'x' gives:7.80 × t - 4.50 × t = 17.3x = 3.3 × 7.80 km

x = 25.74 km

Therefore, the distance from the earthquake epicenter to the seismic station is 25.74 km.

For more such questions on Distance.

https://brainly.com/question/4070274#

#SPJ11

The first application of the Nimbus-3 satellite in 1969 was to observe Earth's weather patterns and collect atmospheric data. The Nimbus-3 satellite observation platform was launched in August 1969, shortly after the Apollo 11 mission.

Nimbus-3 satellite was one of the early weather satellites launched by NASA. It was one of the first satellite platforms to provide detailed observations of Earth’s atmosphere, oceans, and land surfaces. Its primary mission was to study the atmosphere, clouds, and surface temperatures from space. It was also used to measure ocean circulation and sea ice, measure ocean salinity, and observe the interaction of aerosols and clouds. It also monitored precipitation, snow cover, and the energy balance of Earth's atmosphere.

Learn more about satellite: https://brainly.com/question/8376398

#SPJ11

The pucks are covered with velocity so they stick together after the collision.The final velocity of the two pucks is 0.33 m/s.



Applying conservation of linear momentum we get,

mv_1 + 2m.v_2 = (m+2m)v

= v = mv_1 +2mv_2 / m + 2m

= v =v_1 + 2v_2 / 3

Assuming +ve in the right side and -ve in the left side weget

v1 =3m/s v2=-1m/s

v =3+2x(4) / 3 =3-2 / 3 = 1 / 3

= v = 0.33 m/s        As it is +ve so it moves to the right

Velocity is a fundamental concept in physics that describes the rate at which an object changes its position over time. The magnitude of velocity is given by the speed of the object, which is the distance traveled by the object per unit time. The direction of velocity is given by the direction of the object's motion.

Velocity is an important concept in many areas of physics, including mechanics, kinematics, and thermodynamics. In mechanics, velocity is used to describe the motion of objects and the forces acting on them. In kinematics, velocity is used to describe the position and motion of objects without considering the forces acting on them. In thermodynamics, velocity is used to describe the flow of fluids and the transfer of energy and heat.

To learn more about velocity visit here:

brainly.com/question/28738284

#SPJ4

a) The ratio of the rms speed of a gas A atom over the rms speed of a gas B atom is 2:1.

This is because the kinetic energy of a particle is proportional to the square of its mass. Because the mass of a gas A atom is twice the mass of a gas B atom, the rms speed of a gas A atom must be twice the rms speed of a gas B atom to maintain the same temperature.  

b) The ratio of their temperatures must be 2:1. This is because the rms speed of a gas A atom is the same as the rms speed of a gas B atom, so the kinetic energy of each atom must be equal.

Since the kinetic energy is proportional to the square of the mass, the temperature of gas A must be twice that of gas B to maintain the same rms speed.

c) The ratio of the heat capacity of gas A over the heat capacity of gas B is 4:3. This is because the heat capacity is proportional to the mass, and the mass of a gas A atom is twice the mass of a gas B atom.

The ratio of the final pressure of gas A over the final pressure of gas B is 8:9. This is because the pressure is proportional to the temperature, and the temperature of gas A doubles but the temperature of gas B triples. The higher temperature of gas B results in a higher final pressure.

Know more about kinetic energy here

https://brainly.com/question/15764612#

#SPJ11

The natural length of the spring is therefore 12.97 cm.

The natural length of the spring is found by calculating the spring constant using the Hooke's law formula. Spring constant (k) = Force (F) / extension (x). The natural length of the spring refers to the length of the spring when it is not carrying any load. Hooke's law states that the force required to extend or compress a spring by a distance x is proportional to that distance. Mathematically, F=kx, where F is the force applied, x is the displacement from the equilibrium position, and k is the spring constant. To find the natural length of the spring, we need to calculate the spring constant.

To do this, we use the data given in the problem. A load of 12 kg stretches the spring to a total length of 15 cm. We can find the force applied by multiplying the load by the acceleration due to gravity (g), which is 9.8 m/s^2. Thus, F = mg = 12 * 9.8 = 117.6 N. The extension of the spring is given as x = 15 cm - x0, where x0 is the natural length of the spring. Thus, x = 0.15 m - x0. Substituting these values into Hooke's law, we get: k = F/x = 117.6/(0.15 - x0)

Similarly, when a load of 30 kg stretches the spring to a length of 18 cm, we can find the force applied as F = mg = 30 * 9.8 = 294 N. The extension is given as x = 0.18 m - x0. Substituting these values into Hooke's law, we get: k = F/x = 294/(0.18 - x0)

Now we have two equations for k, so we can set them equal to each other: 117.6/(0.15 - x0) = 294/(0.18 - x0) Cross-multiplying and simplifying, we get: 117.6(0.18 - x0) = 294(0.15 - x0) 21.168 - 117.6x0 = 44.1 - 294x0 176.4x0 = 22.932 x0 = 0.1297 m

The natural length of the spring is therefore 12.97 cm.

For more such questions on Hooke's law.

https://brainly.com/question/30611861#

#SPJ11

The kinetic energy of the coffee filter is 0.63 x 10⁻³ J.

Kinetic energy is the energy possessed by a body by virtue of its motion, i.e. when the body is moving. So when the cofffee filter is dropped. it acquires kinetic energy because of its movement.

The kinetic energy of the coffee filter when it reaches the ground can be calculated using the equation:

K = (1/2) mv²

where m is the mass of the object and v is the velocity.

In this case, the mass of the coffee filter is 1.4 g and its velocity when it reaches the ground is 0.9 m/s.

Converting the mass into SI unit, we get mass = 1.4 x 10⁻³ kg

Therefore, the kinetic energy of the coffee filter is:

K = (1/2) x 1.4 x 10 ⁻³g x (0.9 m/s)² = 0.63 x 10⁻³ J

To summarize, the coffee filter of mass 1.4 g that is dropped from a height of 4m and reached the ground with a speed of 0.9 m/s² and has a kinetic energy of 0.63 x 10⁻³ J.

To know more about kinetic energy, refer here:

https://brainly.com/question/999862#

#SPJ4

The frequency of the microwave signal from the standing wave experiments can be calculated by dividing the speed of light by the wavelength of the microwave. The frequency of the microwave signal from the standing wave experiments was 10.525 GHz, which is the same as the manufacturer label.

The speed of light is approximately 300 million meters per second, and the wavelength of the microwave can be determined from the standing wave pattern produced. After dividing the speed of light by the wavelength, the frequency of the microwave signal can be determined.
The frequency of the microwave signal from the standing wave experiments can then be compared to the manufacturer label. The manufacturer label typically states the frequency of the microwave signal in units of gigahertz (GHz). If the frequency calculated from the standing wave experiments is lower than the frequency indicated on the label, then the experiment was not successful. If the frequency calculated from the standing wave experiments is equal to or greater than the frequency indicated on the label, then the experiment was successful.
In conclusion, the frequency of the microwave signal from the standing wave experiments can be calculated by dividing the speed of light by the wavelength of the microwave. The frequency of the microwave signal from the standing wave experiments can then be compared to the manufacturer label. If the frequency calculated from the standing wave experiments is equal to or greater than the frequency indicated on the label, then the experiment was successful. In this case, the frequency of the microwave signal from the standing wave experiments was 10.525 GHz, which is the same as the manufacturer label.

For more such questions on Standing wave.

https://brainly.com/question/28152265#

#SPJ11

the steel ball passes its equilibrium position at approximately 1.42 ft/s each time.

What is the maximum velocity of steel ball?

To find the position x(t) of the steel ball at time t, we need to determine the amplitude, frequency, and period of the oscillations. Here are the steps:

Determine the spring constant (k):

Since the steel ball weighs 64 lb and stretches the spring by 4 ft, the spring constant is k = weight/stretch = 64 lb / 4 ft = 16 lb/ft.

Calculate the mass (m) of the steel ball:

The weight of the steel ball is given as 64 lb. Using the gravitational acceleration g = 32 ft/s², we can find the mass as m = weight/

g = 64 lb / 32 ft/s² = 2 slugs.

Determine the angular frequency (ω):

The angular frequency is related to the spring constant and mass by the formula ω = √(k/m) = √(16 lb/ft / 2 slugs) = 2.83 rad/s.

Calculate the amplitude (A): Since the ball is initially displaced 6 in (0.5 ft) below its equilibrium position, the amplitude is A = 0.5 ft.

Find the period (T): The period of oscillation is related to the angular frequency by the formula T = 2π/ω = 2π/2.83 rad/s ≈ 2.22 s.

Calculate the position x(t): Since the ball executes pure oscillations, the position x(t) can be described by a sine function: x(t) = A * sin(ω * t), where x(t) is positive downwards.

So the position x(t) of the steel ball at time t is x(t) = 0.5 * sin(2.83 * t).

The amplitude of the oscillations is 0.5 ft, the frequency is 2.83 rad/s, and the period is approximately 2.22 s.

To find how fast the ball passes its equilibrium position each time, we can calculate the maximum speed by differentiating the position function:

v(t) = x'(t) = A * ω * cos(ω * t).

The maximum speed occurs when cos(ω * t) = 1, so:

v_max = A * ω = 0.5 ft * 2.83 rad/s ≈ 1.42 ft/s.

Thus, the steel ball passes its equilibrium position at approximately 1.42 ft/s each time.

Learn more about angular frequency.

brainly.com/question/30885221

#SPJ11

The wavelength of light in a medium with a refractive index of 2.0 is 300 nm. This can be calculated using the equation λ1 = λ2/n, where λ1 is the wavelength of light in vacuum (600 nm) and λ2 is the wavelength of light in the liquid (300 nm), and n is the refractive index of the medium (2.0).

The question is asking what the wavelength of light is when it enters a liquid with a refractive index of 2.0. The wavelength of light in a vacuum is 600 nm.

To find the wavelength in the liquid, we need to use the equation: Wavelength in medium = Wavelength in vacuum/Refractive Index. Therefore, the wavelength of light in the liquid would be 300 nm.

In order for light to travel from one medium to another, the refractive index needs to be taken into consideration. Refractive index is defined as the ratio of the speed of light in a vacuum to the speed of light in a particular medium. When light travels from a medium with a high refractive index to one with a lower refractive index, the wavelength of the light will decrease. Therefore, when light with a wavelength of 600 nm enters a liquid with a refractive index of 2.0, the wavelength of the light will decrease to 300 nm.

For more questions related to wavelength.

https://brainly.com/question/12924624

#SPJ11

Star B will appear 1/25 as bright compared to star A.

The brightness of a star is proportional to its luminosity and the distance to it. When the distance between the star and the observer increases, the brightness of the star decreases.

In this case, since star A and star B have identical luminosity, the only difference between them is the distance. Therefore, using the inverse square law of light:

Luminosity = 4πd²B

where L is the luminosity, d is the distance, and B is the brightness.

Therefore, if star A is at a distance of 5 pc and star B is at a distance of 25 pc, the apparent brightness of star B compared to star A can be calculated as:

[tex]\frac{apparent\ brightness\ of\ star\ B}{apparent\ brightness\ of\ star\ A} = \frac{(distance\ to\ star\ A)^2}{(distance\ to\ star \ B)^2}[/tex]

[tex]=\frac{(5\ pc)^2}{(25\ pc)^2}[/tex]

[tex]= \frac{1}{25}[/tex]

So star B will appear 1/25 as bright as star A.

Therefore, the answer is (a) 1/25 as bright.

Learn more about the inverse square law of light:

https://brainly.com/question/2114742

#SPJ11

The power of the car is 30 kW.

A car moving with a constant velocity covering 100 m in 5.0 seconds with 1.5 kN thrust gives us the ability to calculate its power using the following formula:

Power = Thrust × Velocity or (Force x Distance)/Time

To break this down further, power is defined as the rate at which work is done or the rate of energy conversion.

In this case, the thrust of 1.5 kN is the force that the engine exerts on the car, and the distance of 100 m is the distance traveled by car in the time of 5.0 s.

The velocity can be computed by dividing the distance covered by the time that is taken, which is as follows:

Velocity = Distance/Time

Velocity = 100m/5s

Velocity = 20 m/s

Thus, we now have the velocity, which is 20 m/s.

We have the Thrust as well, which is 1.5 kN.

Therefore, we can calculate the power of the car using the formula above:

Power = Thrust × Velocity

Power = 1.5 kN × 20 m/s

Power = 1500 N × 20 m/s

Power = 30,000 Watts =30 kW

Therefore, the power of the car traveling at a constant velocity that covers a distance of 100 m in 5.0 s is 30,000 watts or 30 kW.

To know more about power, refer here:

https://brainly.com/question/29200674#

#SPJ4

(a) The magnitude of electric field in the region between the plates is [tex]\mathbf{9 , 2 5 0}$ $\mathrm{V} / \mathrm{m}$.[/tex]

(b) The magnitude of the force the field exerts on a particle with the given charge i[tex]s $2.22 \times 10^{-5} \mathrm{~N}$.[/tex]

(c) The work done by the field on the particle as it moves from the higher potential plate to the lower is[tex]$8.88 \times 10^{-7} \mathrm{~J}$.[/tex]

(d) the change of the potential energy is[tex]$8.88 \times 10^{-7} \mathrm{~J}$.[/tex]

(a) The magnitude of electric field in the region between the plates is calculated as;

[tex]$$\begin{aligned}& E=\frac{V}{d} \\& E=\frac{370}{40 \times 10^{-3}} \\& E=9,250 \mathrm{~V} / \mathrm{m}\end{aligned}$$[/tex]

(b) The magnitude of the force the field exerts on a particle with the given charge is calculated as follows;

[tex]$$\begin{aligned}& F=E q \\& F=9,250 \times 2.4 \times 10^{-9} \\& F=2.22 \times 10^{-5} \mathrm{~N}\end{aligned}$$[/tex]

(c) The work done by the field on the particle as it moves from the higher potential plate to the lower is calculated as follows;

[tex]$$\begin{aligned}& W=F d \\& W=2.22 \times 10^{-5} \times 40 \times 10^{-3} \\& W=8.88 \times 10^{-7} \mathrm{~J}\end{aligned}$$[/tex]

(d) the change of the potential energy is calculated as;

[tex]$$\begin{aligned}& \Delta U=q \Delta V \\& \Delta U=q\left(V_1-V_2\right)\end{aligned}$$$$\text { DeltaU }=2.4 \times 10^{-9}(370)$$$$\Delta U=8.88 \times 10^{-7} \mathrm{~J}$$[/tex]

Learn more about electric field

https://brainly.com/question/15170044

#SPJ4

Full Question: Two large, parallel, metal plates carry opposite charges of equal magnitude. They are separated by a distance of 40.0 mm, and the potential difference between them is 370 V

A. What is the magnitude of the electric field (assumed to be uniform) in the region between the plates?

B. What is the magnitude of the force this field exerts on a particle with a charge of 2.40 nC ?

C. Use the results of part (b) to compute the work done by the field on the particle as it moves from the higher-potential plate to the lower.

D. Compare the result of part (c) to the change of potential energy of the same charge, computed from the electric potential.

a) $$E_1 = \frac{(9.0 \times 10⁹ N m²/C²)(2.6 \times 10⁻⁶C)}{(3.0 m)²} \approx 7.80 \times 10⁵ N/C$$, direction is to the right ; b) $$E_2 = \frac{(9.0 \times 10⁹ N m²/C²)(1.4 \times 10⁻⁶ C)}{(4.0 m)²} \approx 3.94 \times 10⁵ N/C$$, electric field is directed towards point charge so, direction is to the left  c) $$|\vec{E}| = \√{E_1² + E_2²} \approx 8.86 \times 10⁵ N/C$$ and its direction is up.

Charge that exists in a body that has fewer electrons than protons is known as positive electrons.

a. To find the electric field at the origin due to charge Q1, we can use the formula for the electric field due to point charge:

$$E_1 = \frac{k Q_1}{r_1²}$$

k is Coulomb constant (k = 9.0 × 10⁹ N m²/C²), Q1 is the charge, and r1 is the distance from the charge to the point where we want to find the electric field.

Q1 = 2.6 μC and r1 = 3.0 m (since x1 = -3.0 m is the distance from Q1 to the origin).

$$E_1 = \frac{(9.0 \times 10⁹ N m^2/C²)(2.6 \times 10⁻⁶C)}{(3.0 m)²} \approx 7.80 \times 10⁵ N/C$$

The electric field is directed away from point charge, so direction of the electric field at the origin due to Q1 is to the right (positive x direction).

b. Similarly, to find the electric field at the origin due to charge Q2, we use the same formula:

$$E_2 = \frac{k Q_2}{r_2²}$$

where Q2 = 1.4 μC and r2 = 4.0 m (since x2 = 4.0 m is the distance from Q2 to the origin).

$$E_2 = \frac{(9.0 \times 10⁹ N m²/C²)(1.4 \times 10⁻⁶ C)}{(4.0 m)²} \approx 3.94 \times 10⁵ N/C$$

The electric field is directed towards point charge, so direction of the electric field at the origin due to Q2 is to the left.

c. $$\vec{E} = \vec{E_1} + \vec{E_2}$$

$\vec{E_1}$ is the electric field due to Q1 and $\vec{E_2}$ is the electric field due to Q2.

net electric field at the origin is: $$|\vec{E}| = \√{E_1² + E_2²} \approx 8.86 \times 10⁵ N/C$$ and its direction is up.

To know more about charge, refer

https://brainly.com/question/25922783

#SPJ1

The final answer are force exerted by the bar on the gymnast's hands will be 500 N.

According to the given problem, a 500 N gymnast performs a stationary handstand on the high bar. The problem asks to determine how much force is exerted by the bar on the gymnast's hands.

To solve this problem, we need to apply Newton's third law of motion.

Newton's third law of motion states that every action has an equal and opposite reaction. The force exerted by the gymnast on the bar is equal in magnitude and opposite in direction to the force exerted by the bar on the gymnast.

Thus, the force exerted by the bar on the gymnast's hands will be 500 N.

How much force is exerted by the bar on the gymnast's hands? The force exerted by the bar on the gymnast's hands is 500 N.

To know more about force refer here:

https://brainly.com/question/13191643#

#SPJ11

From the sketch, we can deduce that the two charges q1 and q2 are of opposite signs, as field lines start at the positive charge q1 and end at the negative charge q2. The field lines also indicate that the magnitude of the electric field produced by q1 is larger than that of q2.

Learn more about electric field at: https://brainly.com/question/14372859

#SPJ11

The total heat flux from the black body is 42643 W/m², due to radiation heat transfer, from a black body if the surface temperature is 600°C.

The heat flux due to radiation heat transfer from a black body can be calculated using the Stefan-Boltzmann law, which states that the heat flux is proportional to the fourth power of the temperature:

[tex]q(rad) = \sigma * \epsilon * A * T^4[/tex]

Where q(rad) is the heat flux (W/m²), σ is the Stefan-Boltzmann constant ([tex]5.67 * 10^{-8[/tex] W/m²K⁴), ε is the emissivity of the black body (assumed to be 1 for a perfect black body), A is the surface area of the black body, and T is the temperature in Kelvin.

To convert the temperature of 600°C to Kelvin, we add 273.15 K:

T = (600 + 273.15) K = 873.15 K

Assuming the black body has a unit surface area (A = 1 m²), the heat flux due to radiation can be calculated as:

[tex]q(rad) = \sigma * \epsilon * A * T^4 = 5.67 * 10^{-8} * 1 * 1 * (873.15)^4 = 14098[/tex] W/m²

The heat flux due to convection can be calculated using the following equation:

q(conv) = h * (T(surface) - T(air))

Where q(conv) is the heat flux (W/m²), h is the convection heat transfer coefficient (55 W/(m²°C)), T(surface) is the surface temperature (600°C), and T(air) is the air temperature (assumed to be 25°C).

To convert the surface temperature and air temperature to Kelvin, we add 273.15 K:

T(surface) = 600 + 273.15 = 873.15 K

T(air) = 25 + 273.15 = 298.15 K

Substituting the values, we get:

q(conv) = 55 * (873.15 - 298.15) = 28545 W/m²

Therefore, the total heat flux from the black body is:

q(total) = q(rad) + q(conv) = 14098 + 28545 = 42643 W/m²

learn more about heat flux

brainly.com/question/30708042

#SPJ4

The frequency of a standing wave with a wave speed of 12 m/s as it travels on a 4.0-m string fixed at both ends is 3.0 Hz.

A standing wave is produced by a wave with the same amplitude, frequency, and wavelength moving in the opposite direction with the initial wave. This indicates that the wave appears to stand in one place. Standing waves can only be generated in a medium if there is a boundary that restricts the movement of the wave. Standing waves can be observed in various shapes and sizes, and their frequencies are determined by a variety of factors, including the wave speed and the length of the string. When a standing wave is generated in a string, the points where the wave appears to be fixed are known as nodes, while the points where the string vibrates with the most amplitude are known as antinodes.In this scenario, the wave speed and the length of the string are given.

The wave speed, frequency, and wavelength of a wave are related by the formula v = fλ, where v is the wave speed, f is the frequency, and λ is the wavelength. Since the length of the string is fixed, the wavelength of the standing wave is twice the length of the string. Thus, λ = 2L = 8 m. Plugging in the values for the wave speed and wavelength, the frequency can be calculated as follows:f = v / λ = 12 m/s / 8 m = 1.5 Hz. The frequency of a standing wave with a wave speed of 12 m/s as it travels on a 4.0-m string fixed at both ends is 3 Hz.

Learn more about a standing wave at https://brainly.com/question/29558685

#SPJ11

The type of microscope that has the highest resolution and can resolve objects less than 1 angstrom apart is the Transmission electron microscope (TEM).

What is a microscope?

A microscope is an instrument that allows scientists and medical experts to examine microscopic organisms and objects. They are used in a variety of scientific and medical fields to investigate the behavior of cells and other microscopic organisms. Scientists also use microscopes to study the surface of materials, such as metals or plastics, in order to understand how they are made and how they behave.

There are several types of microscopes, each with its own set of advantages and disadvantages. The highest resolution and the most powerful microscopes are the electron microscopes. The electron microscope utilizes electrons instead of light to create an image.

They use an electron beam to create a magnified image of a sample. The transmission electron microscope (TEM) is the most powerful type of electron microscope. They use an electron beam to send electrons through a thin section of a sample, which creates a magnified image of the sample on a screen.

The resolution of the TEM is extremely high, allowing scientists to study the sample's internal structure in great detail. As a result, it is capable of detecting objects that are less than one angstrom apart. The atomic structure of materials can also be viewed using this type of microscope.

Learn more about transmission electron microscope (TEM) here:

https://brainly.com/question/10933178#

#SPJ11