Answers
Answer:
Step-by-step explanation:
Its D
Related Questions
Question 4: According to given water network system below; a) Design the main and primary pipes of the network by using dead point method. b) Find the elevation of the water tank. c) Find the dynamic pressures at points A, B, C, D, E. (maxqday = 300 1/day capita, William Hazen coefficient; C = 120, William Hazen formula; V = 0.85CR43 70.54, Minimum allowable pressure (Ply Janin, network=20 mwc) Use Standart Pipe Diameters as 80mm, 100mm, 125mm, 175mm, 200mm, 250mm, 300mm.... Q=41sec TANK B(35m) T(50m) L-100m L-600m 15 L-250m kw A(38m) C(30m) L-500m K1.5 L-400m k1 D(32m) L-700m k=15 E (26m)
Answers
Designing the water network system using the dead point method, determining the elevation of the water tank, and calculating the dynamic pressures at various points.
The main and primary pipes of the water network system can be designed using the dead point method, which involves considering the elevation of the water sources and the desired minimum allowable pressure at various points. By analyzing the given information and applying the William Hazen coefficient (C = 120) and formula (V = 0.85CR^0.43), the appropriate pipe diameters can be selected for the main and primary pipes.
Additionally, the elevation of the water tank can be determined by evaluating the given distances and elevations of the pipes. Finally, by considering the flow rates and pipe characteristics, the dynamic pressures at points A, B, C, D, and E can be calculated.
Step 2: In order to design the main and primary pipes of the water network system, we can utilize the dead point method. This method takes into account the elevation of the water sources and the desired minimum allowable pressure at various points.
By applying the given information and employing the William Hazen coefficient (C = 120) and formula (V = 0.85CR^0.43), we can select suitable pipe diameters for the main and primary pipes. The dead point method ensures that the water flow remains at a minimum acceptable pressure throughout the network.
To determine the elevation of the water tank, we need to consider the given distances and elevations of the pipes. By analyzing the information provided, we can calculate the elevation of the water tank by summing up the elevation changes along the pipe network. This will give us the necessary information to place the water tank at the appropriate height.
Additionally, we can calculate the dynamic pressures at points A, B, C, D, and E by taking into account the flow rates and pipe characteristics. The flow rate can be determined using the maximum daily water demand (maxqday = 300 1/day capita), and by applying the William Hazen formula (V = 0.85CR^0.43), we can calculate the velocity of the water in the pipes.
With the pipe diameters provided (80mm, 100mm, 125mm, 175mm, 200mm, 250mm, 300mm), we can calculate the dynamic pressures at each point using the Hazen-Williams equation.
Learn more about Network
brainly.com/question/29350844
#SPJ11
Find the distance from the point (0,−5,−3) to the plane −5x+y−3z=7.
Answers
The distance from the point (0,-5,-3) to the plane [tex]-5x+y-3z=7[/tex] is 3 units.
To find the distance between a point and a plane, we can use the formula:
[tex]\[ \text{Distance} = \frac{{\lvert Ax_0 + By_0 + Cz_0 + D \rvert}}{{\sqrt{A^2 + B^2 + C^2}}} \][/tex]
where [tex](x_0, y_0, z_0)[/tex] represents the coordinates of the point, and A, B, C, and D are the coefficients of the plane's equation.
In this case, the equation of the plane is [tex]-5x + y - 3z = 7[/tex]. Comparing this with the standard form of a plane's equation, [tex]Ax + By + Cz + D = 0[/tex], we have
A = -5, B = 1, C = -3, and D = -7.
Plugging in the values into the distance formula, we get:
[tex]\[ \text{Distance} = \frac{{\lvert -5(0) + 1(-5) + (-3)(-3) + (-7) \rvert}}{{\sqrt{(-5)^2 + 1^2 + (-3)^2}}} = \frac{{\lvert -5 + 5 + 9 - 7 \rvert}}{{\sqrt{35}}} = \frac{{\lvert 2 \rvert}}{{\sqrt{35}}} = \frac{2}{{\sqrt{35}}} \][/tex]
Therefore, the distance from the point (0,-5,-3) to the plane [tex]-5x+y-3z=7[/tex] is approximately 0.338 units.
To learn more about plane refer:
https://brainly.com/question/28247880
#SPJ11
By finding the modular inverse and multiplying both sides by it, we can obtain the solution to the given linear congruence. The solution is x ≡ 195 (mod 539).
To solve the linear congruence 6 * 1107x ≡ 263 (mod 539), we need to find a value of x that satisfies this equation.
Step 1: Reduce the coefficients and constants:
The given equation can be simplified as 1107x ≡ 263 (mod 539) since 6 and 539 are coprime.
Step 2: Find the modular inverse:
To eliminate the coefficient, we need to find the modular inverse of 1107 modulo 539. Let's call this inverse a.
1107a ≡ 1 (mod 539)
By applying the Extended Euclidean Algorithm, we find that a ≡ 183 (mod 539).
Step 3: Multiply both sides by the modular inverse:
Multiply both sides of the equation by 183:
183 * 1107x ≡ 183 * 263 (mod 539)
x ≡ 48129 ≡ 195 (mod 539)
Therefore, the solution to the linear congruence 6 * 1107x ≡ 263 (mod 539) is x ≡ 195 (mod 539).
Learn more about linear congruence
https://brainly.com/question/34497495
#SPJ11
A single-stage absorption process is used to remove CO 2
from the fluegas stream of a fired kiln at a cement factory. The equilibrium relationship for the absorption process can be approximated as Y=2X, where Y and X are mole ratios of CO 2
in the gas and liquid phases respectively. The input gas stream is 10%CO 2
(on a molar basis) and the flow rate is 100kmols −1
. The input liquid stream is 0.2%CO 2
(on a molar basis) and the desired output gas is to contain 2%CO 2
(on a molar basis). Calculate the required flow rate of liquid into the separation process. [8 marks] Now consider an alternative absorption process consisting of two countercurrent equilibrium stages. The flow rates and compositions of both the gas and liquid inlet streams to the two-stage unit are identical to part a), and the same equilibrium relationship is applicable. What is the mole fraction of CO 2
in the gas stream leaving the separator?
Answers
The mole fraction of CO2 in the gas stream leaving the separator will be 0.05.
The required flow rate of liquid into the single-stage absorption process can be calculated using the mole ratios and the desired output composition.
In the single-stage absorption process, the equilibrium relationship between the mole ratios of CO2 in the gas (Y) and liquid (X) phases can be approximated as Y = 2X.
Given that the input gas stream is 10% CO2 (on a molar basis) and the flow rate is 100 kmols^-1, we can calculate the mole ratio of CO2 in the gas phase (Y):
Y = (10% CO2) / (100 kmols^-1) = 0.1
Since the equilibrium relationship is Y = 2X, we can substitute the value of Y to find X:
0.1 = 2X
X = 0.05
Therefore, the mole ratio of CO2 in the liquid phase (X) is 0.05.
The input liquid stream is 0.2% CO2 (on a molar basis), and the desired output gas is to contain 2% CO2 (on a molar basis).
To calculate the required flow rate of liquid into the separation process, we need to find the mole ratio of CO2 in the liquid phase at the desired output composition. Let's assume the required flow rate of liquid is L kmols^-1.
Using the equilibrium relationship Y = 2X, we can find the mole ratio of CO2 in the gas phase (Y) at the desired output composition:
2X = Y
2(0.05) = 0.02
Y = 0.02
Now, we can calculate the mole ratio of CO2 in the gas stream at the desired output composition:
(2% CO2) / (L kmols^-1) = 0.02
Simplifying this equation, we find:
L = (2% CO2) / 0.02
L = 100 kmols^-1
Therefore, the required flow rate of liquid into the separation process is 100 kmols^-1.
Now let's consider the alternative absorption process consisting of two countercurrent equilibrium stages, where the flow rates and compositions of both the gas and liquid inlet streams are identical to the single-stage unit.
Using the same equilibrium relationship Y = 2X, the mole fraction of CO2 in the gas stream leaving the separator can be determined.
Since the input gas stream is 10% CO2 (on a molar basis), the mole ratio of CO2 in the gas phase (Y) is 0.1.
For each equilibrium stage, the mole ratio of CO2 in the liquid phase (X) can be calculated using the equilibrium relationship Y = 2X:
0.1 = 2X
X = 0.05
Since the two stages are countercurrent, the mole ratio of CO2 in the gas phase at the separator outlet will be equal to the mole ratio of CO2 in the liquid phase at the second stage.
Therefore, the mole fraction of CO2 in the gas stream leaving the separator will be 0.05.
Know more about mole fraction:
https://brainly.com/question/30724931
#SPJ11
. If you dilute 175 mL of a 1.6 M solution of LiCI to 1.0 L, determine the new concentration of the solution: 2. You need to make 10.0 L of 1.2 M KNO3. What molarity would the potassium nitrate solution need to be if you were to use only 2.5 L of it?: 3. Back to question 1. Would the two options below give the same result? (explain) 175mL of 1.6M solution of LICI + 825mL of water 175mL of 1.6M solution of LiCl + whatever amount of water needed to fill a 1L volumetric flask? ? a. b. (clue: options a and b are not the same, can you explain why?)
Answers
In option a, the final volume is 175 mL + 825 mL = 1000 mL = 1.0 L.
In option b, the final volume is 1.0 L.
1. To determine the new concentration of the LiCI solution after dilution, we can use the formula:
M1V1 = M2V2
where M1 is the initial molarity, V1 is the initial volume, M2 is the final molarity, and V2 is the final volume.
Given:
M1 = 1.6 M (initial molarity)
V1 = 175 mL (initial volume)
V2 = 1.0 L (final volume)
First, we need to convert the initial volume from milliliters to liters:
V1 = 175 mL = 0.175 L
Now we can substitute the values into the formula:
(1.6 M)(0.175 L) = M2(1.0 L)
Simplifying the equation, we have:
0.28 = M2(1.0)
Dividing both sides by 1.0, we find:
M2 = 0.28 M
Therefore, the new concentration of the solution after dilution is 0.28 M.
2. To determine the molarity of the potassium nitrate solution needed, we can again use the formula:
M1V1 = M2V2
Given:
M1 = unknown (initial molarity)
V1 = 2.5 L (initial volume)
M2 = 1.2 M (final molarity)
V2 = 10.0 L (final volume)
Substituting the values into the formula:
(unknown)(2.5 L) = (1.2 M)(10.0 L)
Simplifying the equation, we have:
2.5 M = 12 M
Dividing both sides by 2.5, we find:
unknown = 4.8 M
Therefore, the potassium nitrate solution needs to have a molarity of 4.8 M if only 2.5 L of it is used to make 10.0 L of a 1.2 M solution.
3. Now let's compare the two options given in question 1 to see if they would give the same result. The two options are:
a) 175 mL of 1.6 M solution of LiCl + 825 mL of water
b) 175 mL of 1.6 M solution of LiCl + whatever amount of water needed to fill a 1 L volumetric flask
In option a, the final volume is 175 mL + 825 mL = 1000 mL = 1.0 L.
In option b, the final volume is 1.0 L.
Both options have the same final volume of 1.0 L. However, the concentration of the solution in option a is diluted because we added 825 mL of water. In option b, we added only enough water to fill the flask to 1.0 L, without diluting the original concentration.
Therefore, option a and option b would give different results because option a would result in a lower concentration compared to option b.
Learn more about final volume:
https://brainly.com/question/14197390
#SPJ11
The specific death constant of a new strain of Bacillus subtilis was determined to be 0.012 min* at 85 °C and 1.60 min at 110°C Determine the activation energy for the thermal death of 8. subtilise A: 223 k moi
Answers
The activation energy for the thermal death of Bacillus subtilis is approximately 223,000 J/mol.
The activation energy for the thermal death of a strain of Bacillus subtilis can be determined using the Arrhenius equation. The equation is given by:
k = A * exp(-Ea / (R * T))
Where:
- k is the specific death constant,
- A is the pre-exponential factor,
- Ea is the activation energy,
- R is the gas constant (8.314 J/(mol*K)),
- T is the temperature in Kelvin.
To determine the activation energy, we need to use the given data for two different temperatures (85°C and 110°C) and their corresponding specific death constants (0.012 min^-1 and 1.60 min^-1).
Let's convert the temperatures from Celsius to Kelvin:
- 85°C + 273.15 = 358.15 K
- 110°C + 273.15 = 383.15 K
Now we can use the Arrhenius equation to set up two equations using the given data points:
For 85°C:
0.012 = A * exp(-Ea / (8.314 * 358.15))
For 110°C:
1.60 = A * exp(-Ea / (8.314 * 383.15))
By dividing the second equation by the first equation, we can eliminate the pre-exponential factor (A):
(1.60 / 0.012) = exp(-Ea / (8.314 * 383.15)) / exp(-Ea / (8.314 * 358.15))
133.33 = exp((8.314 * 358.15 - 8.314 * 383.15) / (8.314 * 358.15 * 383.15))
Taking the natural logarithm (ln) of both sides:
ln(133.33) = (8.314 * 358.15 - 8.314 * 383.15) / (8.314 * 358.15 * 383.15)
Simplifying the right side:
ln(133.33) = -Ea / (8.314 * 358.15 * 383.15)
Solving for Ea:
Ea = -ln(133.33) * (8.314 * 358.15 * 383.15)
Calculating Ea:
Ea ≈ 223,000 J/mol
Therefore, the activation energy for the thermal death of Bacillus subtilis is approximately 223,000 J/mol.
Know more about activation energy here:
https://brainly.com/question/28384644
#SPJ11
What is the factored form of this expression? x2 − 12x + 36 A. (x + 6)2 B. (x − 6)2 C. (x − 6)(x + 6) D. (x − 12)(x − 3)
Answers
Answer:
The correct answer is A. (x + 6)^2.
Step-by-step explanation:
To find the factored form of the expression x^2 - 12x + 36, we can factor it by looking for two binomials that, when multiplied, result in the original expression.
The expression can be factored as (x - 6)(x - 6), which simplifies to (x - 6)^2.
Therefore, the factored form of x^2 - 12x + 36 is (x - 6)^2.
The answer is:
(x - 6)²Work/explanation:
To factor the expression [tex]\sf{x^2-12x+36}[/tex], we should look for two numbers that multiply to 36 and add to -12.
These numbers are -6 and -6.
We write the factored expression like this : (x - 6)(x - 6).
Which is the same as (x - 6)².
Therefore, the answer is (x - 6)².Summary of the Qualitative Tests for Carbohydrates: 1. Molish Test: Identifies if a sample is a carbohydrate - A positive Molish test forms a "purple ring" in the middle of two layers 2. Iodine Test: Identifies if a sample is a polysaccharide
- A positive Iodine test turns the solution blue/black - Positive for Starch
Answers
The qualitative tests for carbohydrates include the Molish test, which detects the presence of carbohydrates through the formation of a purple ring, and the iodine test, which specifically identifies polysaccharides.
The Molish test is a chemical test used to detect the presence of carbohydrates in a given sample. In this test, the sample is first treated with alpha-naphthol, followed by the addition of concentrated sulfuric acid. If the sample contains carbohydrates, such as monosaccharides or disaccharides, a purple ring forms at the junction of the two layers, indicating a positive result.
The iodine test is another common test for carbohydrates, specifically targeting polysaccharides like starch. In this test, the sample is treated with iodine solution. If the sample contains starch, it forms a blue-black color due to the formation of an iodine-starch complex. This color change indicates the presence of polysaccharides, specifically starch.
To know more about qualitative tests,
https://brainly.com/question/31663349
#SPJ11
A 1/30 model was made to conduct a water test on a hydroelectric power plant. Answer the following questions about this model experiment.
1. What is the flow rate of the model for the flood of the circle to Qp = 500 m3/sec?
2. In the model, the value of measuring the flow rate of the arc was 2m/sec. What is the flow velocity in a circle?
Answers
The flow rate of the model for the flood of the circle, given a flow rate of Qp = 500 m³/sec, can be determined using the scale of 1/30. 2. The flow velocity in the circle of the model, based on a measured flow rate of 2 m/sec for the arc, is 0.067 m/sec.
The flow rate of the model for the flood of the circle, scaled down by a factor of 1/30, is 16.67 m³/sec. To calculate the flow rate of the model, we can use the concept of similarity between the model and the actual system. In a hydraulic model, the flow rates are directly proportional to the cross-sectional areas. Since the model scale is 1/30, the flow rate of the model can be obtained by multiplying the flow rate of the prototype (Qp) by the square of the scale factor (1/30)². Given that Qp = 500 m³/sec, we can calculate the flow rate of the model (Qm) as follows:
[tex]\[Qm = Qp \times (scale\ factor)^2 = 500 \, m³/sec \times (1/30)^2 = 16.67 \, m³/sec\][/tex]
Therefore, the flow rate of the model for the flood of the circle is 16.67 m³/sec.
To determine the flow velocity in the circle, we need to consider the relationship between flow rate, flow velocity, and cross-sectional area. In a circular cross-section, the flow rate (Q) is equal to the product of the flow velocity (V) and the cross-sectional area (A). Since we know the flow rate of the arc (Qm) is 2 m³/sec and the flow rate of the circle (Qm) is 16.67 m³/sec (as calculated in the previous question), we can set up the following equation:
[tex]\( Qm_{arc} = Qm_{circle} = A_{arc} \times V_{arc} = A_{circle} \times V_{circle} \)[/tex]
Assuming the cross-sectional areas of the arc and the circle are the same (since they are geometrically similar), we can rearrange the equation to solve for the flow velocity in the circle (Vcircle):
[tex]\( V_{circle} = \frac{{Qm_{circle}}}{{A_{circle}}} = \frac{{16.67 \, m³/sec}}{{A_{circle}}} \)[/tex]
To find the flow velocity in the circle, we need the cross-sectional area of the circle. However, the given information does not provide the necessary details to calculate it. Therefore, without the specific dimensions of the circle's cross-section, we cannot determine the exact flow velocity in the circle.
To learn more about flow rate refer:
https://brainly.com/question/31070366
#SPJ11
The flow rate of the model for the flood in the circle is 16.67 m³/sec, and the flow velocity in the circle is 2 m/sec.
The 1/30 model experiment conducted on a hydroelectric power plant aimed to test the flow rate of the model during a flood. The flow rate, Qp, was set at 500 m³/sec. In the model, the measured flow rate of the arc was 2 m/sec.
1. The flow rate of the model for the flood in the circle can be determined using the scale ratio of the model. Since it is a 1/30 model, the flow rate of the model is 30 times smaller than the actual flow rate. Therefore, to calculate the flow rate in the model, we need to divide the given flow rate, Qp = 500 m³/sec, by the scale ratio: 500 m³/sec ÷ 30 = 16.67 m³/sec.
2. The flow velocity in the circle can be obtained by relating the flow rate to the cross-sectional area of the circle. Since the flow rate in the model is 16.67 m³/sec and the value of measuring the flow rate of the arc is 2 m/sec, we can find the cross-sectional area of the circle using the formula: flow rate = velocity × area. Rearranging the equation to solve for the area, we have: area = flow rate / velocity = 16.67 m³/sec ÷ 2 m/sec = 8.335 m².
To learn more about velocity refer:
https://brainly.com/question/29523095
#SPJ11
Derive the following design equations starting from the general mole balance equation a) CSTR b) Batch c) PBR [7] [7] [6] 12 Marks Question 2 a) Describe the three ways in which a chemical species can lose its identity and give an example for each. [6] b) With the aid of a sketch illustrate the rate of reaction in relation to reagents and products.
Answers
The concentration of reactants decreases, and the concentration of products increases as the reaction progresses. The reaction rate increases as the concentration of reactants decreases.
Design equations for different reactor types: CSTR: Consider a well-mixed reactor where the contents of the reactor are instantly and thoroughly mixed, and where the outlet stream has the same composition as that in the reactor.
Consider a continuous flow of fluid entering the reactor and leaving the reactor at the same rate. The rate of accumulation of the chemical in the tank equals the rate of flow in minus the rate of flow out. The volume of the reactor is constant since the reactor is a well-mixed continuous flow reactor, and thus the reactor is of constant volume.
Batch: A batch reactor is a vessel that holds reactants for an extended period of time. It is a sealed system that can be operated in a range of temperature and pressure conditions. In batch processes, the process cycle is repeated to achieve the required product output. In a batch reactor, the energy required for a reaction is supplied as heat via the jacket.
PBR: A plug flow reactor (PFR) or continuous tubular reactor (CTR) is an open system that has a fixed flow rate. It has no internal mixing, and the concentration of the fluid varies along the length of the reactor. Because the reactants enter and leave the reactor continuously, the volume of the fluid within the reactor is constant. The reaction rate of a plug flow reactor is dependent on the amount of time the reactants spend within the reactor. Description of the three ways in which a chemical species can lose its identity and give an example for each:
The three ways in which a chemical species can lose its identity are:
1. Chemical Reactions: This is the most common method for a chemical species to lose its identity. When a substance reacts chemically with another substance to form a new product, this occurs. For example, when magnesium reacts with hydrochloric acid, it produces magnesium chloride and hydrogen gas.
2. Radioactive decay: This is the process by which a substance loses its identity as a result of radioactive decay. When the nucleus of an atom is unstable, it may spontaneously emit radiation and change into a different element. For example, when radium decays, it becomes radon.
3. Photolysis: This is the process by which a substance loses its identity as a result of exposure to light. When a substance is exposed to light, it may decompose into its constituent parts.
For example, when chlorine gas is exposed to ultraviolet light, it decomposes into chlorine atoms. Sketch illustrating the rate of reaction in relation to reagents and products: The rate of reaction is the amount of product formed or reactant consumed per unit time. The reaction rate is dependent on the concentration of the reactants, temperature, catalyst, surface area, and other factors. The graph illustrates the relationship between the concentration of reactants and products and the reaction rate. The concentration of reactants decreases, and the concentration of products increases as the reaction progresses. The reaction rate increases as the concentration of reactants decreases.
Learn more about batch reactor visit:
brainly.com/question/33227944
#SPJ11
The linear BVP describing the steady state concentration profile C(x) in the following reaction-diffusion problem in the domain 0≤x≤ 1, can be stated as d²C_C=0 - dx² with Boundary Conditions: C(0) = 1 dC (1) = 0 dx The analytical solution: C(x) = e(2-x) + ex (1+e²) Solve the BVP using finite difference methode and plot together with analytical solution Note: Second Derivative= C₁-1-2 C₁+Cj+1 (A x)² First Derivative: - Cj+1-C₁-1 (2 Δ x)
Answers
The steady state concentration profile C(x) in the given reaction-diffusion problem can be solved using the finite difference method. The analytical solution for C(x) is also provided, which can be used to compare and validate the numerical solution.
To solve the problem using the finite difference method, we can discretize the domain into N+1 equally spaced points, where N is the number of grid points. Using the second-order central difference approximation for the second derivative and the first-order forward difference approximation for the first derivative, we can obtain a system of linear equations. Solving this system will give us the numerical solution for C(x).
In the first step, we need to set up the linear system of equations. Considering the grid points from j=1 to j=N-1, we can write the finite difference equation for the given problem as follows:
-C(j+1) + (2+2Δx²)C(j) - C(j-1) = 0
where Δx is the grid spacing. The boundary conditions C(0) = 1 and dC(1)/dx = 0 can be incorporated into the system of equations as well.
In the second step, we can solve this system of equations using numerical methods such as Gaussian elimination or matrix inversion to obtain the numerical solution for C(x).
In the final step, we can plot the numerical solution obtained from the finite difference method along with the analytical solution C(x) = e^(2-x) + ex/(1+e²) to compare and visualize the agreement between the two solutions.
Learn more about the analytical solution
brainly.com/question/33730824
#SPJ11
Consider these two functions:
F(x)=2 cos(pix)
G(x) = 1/2cos(2x) What are the amplitudes of the two functions?
Answers
The amplitude of function F(x) is 2, and the amplitude of function G(x) is 1/2.
To determine the amplitudes of the given functions F(x) = 2cos(pix) and G(x) = 1/2cos(2x), we need to identify the coefficients in front of the cosine terms. The amplitude of a cosine function is the absolute value of the coefficient of the cosine term.
For function F(x) = 2cos(pix), the coefficient in front of the cosine term is 2. Thus, the amplitude of F(x) is |2|, which is equal to 2.
For function G(x) = 1/2cos(2x), the coefficient in front of the cosine term is 1/2. The amplitude is the absolute value of this coefficient, so the amplitude of G(x) is |1/2|, which simplifies to 1/2.
In summary, the amplitude of function F(x) is 2, and the amplitude of function G(x) is 1/2.
For more questions on cosine function, click on:
https://brainly.com/question/12617989
#SPJ8
A cylindrical tank, filled with water and axis vertical, is open at one end and closed at the other end. The tank has a diameter of 1.2m and a height of 3.6m. It is then rotated about its vertical axis with an angular speed w. Determine w in rpm so that one third of the volume of water inside the cylinder is spilled
Answers
Therefore, the angular velocity of the cylindrical tank so that one-third of the volume of water inside the cylinder is spilled is 33.33 rpm.
Angular velocity w in rpm = 33.33rpm
Given that the diameter of the cylindrical tank is 1.2m and height is 3.6m.
The volume of the cylinder is given by:
Volume of cylinder = πr²h
Where r = 0.6 m (diameter/2)
h = 3.6 m
Volume of cylinder = π(0.6)² × 3.6
Volume of cylinder = 1.238 m³
Let the level of the water inside the cylinder before rotating be h₀, such that:
Volume of water = πr²h₀Spilling of water by one third is equivalent to two thirds remaining in the tank.Thus, the volume of water remaining in the cylinder after spilling one-third is given by:
Volume of water remaining = (2/3) πr²h₀
We can also write:
Volume of water spilled = (1/3) πr²h₀
Volume of water remaining + Volume of water spilled = πr²h₀
Rearranging the equation and substituting known values,
we get:(2/3) πr²h₀ + (1/3) πr²h₀ = πr²h₀
Simplifying the equation and canceling out like terms, we get:
2/3 + 1/3 = 1h₀ = (1/2) × 3.6h₀ = 1.8 m
The volume of water inside the tank is given by:
Volume of water = πr²h₀ = π(0.6)² × 1.8
= 0.6105 m³
To know more about volume visit:
https://brainly.com/question/28338582
#SPJ11
Help me with this 9 math
Answers
The height of the cylinder is 4 feet.
How to find the height of a cylinder?The volume of a cylinder can be found as follows;
volume of a cylinder = base area × height
Therefore,
base area = πr²
volume of the cylinder = 48π ft³
base area = 12π ft²
Therefore, let's find the height of the cylinder as follows:
48π = 12π × h
divide both sides of the equation by 12π
h = 48π / 12π
h = 4 ft
Therefore,
height of the cylinder = 4 feet
learn more on volume here: https://brainly.com/question/28512386
#SPJ1
C-14 has a half-life of 5730 years. The activity of a sample of wood recovered from an ancient burial site is 700 dph. This was compared to a similar piece of wood which has a current activity of 920 dph. What is the estimated age (yr) of the wood from the burial site? 700 4800 1700 3700 2300
Answers
The half-life of C-14 is 5730 years.
The activity of the wood sample from the ancient burial site is 700 dph, while a similar piece of wood has a current activity of 920 dph. We can use the concept of half-life to estimate the age of the wood from the burial site.
To do this, we need to determine the number of half-lives that have occurred for the difference in activities between the two samples.
The difference in activity is 920 dph - 700 dph = 220 dph.
Since the half-life of C-14 is 5730 years, we divide the difference in activities by the decrease in activity per half-life:
220 dph / (920 dph - 700 dph) = 220 dph / 220 dph = 1 half-life.
So, the estimated age of the wood from the burial site is equal to one half-life of C-14, which is 5730 years.
Therefore, the estimated age of the wood from the burial site is 5730 years.
Learn more about carbon dating:
https://brainly.com/question/15673495
#SPJ11
Find the x-values (if any) at which f' is not continues. f(x)=²4 a) g(x) = 8. 4. Find the constant a, such that the function is continues on the entire real number line. -a² a xa b) x=0 x+1, x ≤ 2 = 3-x x>2 f(x) =
Answers
The series Σ(-2) can be represented as -2 + (-2) + (-2) + ...
The partial sums of this series are: -2, -4, -6, ...
In reduced fraction form, the first three terms of the sequence of partial sums are:
-2/1, -4/1, -6/1.
The series Σ(-2) represents an infinite sequence of terms, where each term is -2. To find the partial sums, we add up the terms of the series starting from the first term and progressing through the sequence.
The first term of the partial sum is -2 since it is the only term in the series.
To find the second term of the partial sum, we add the first term (-2) to the second term in the series, which is also -2. Thus, -2 + (-2) = -4.
Similarly, to find the third term of the partial sum, we add the first two terms (-2 + (-2)) to the third term in the series, which is also -2. Hence, -2 + (-2) + (-2) = -6.
In reduced fraction form, the first three terms of the sequence of partial sums are -2/1, -4/1, and -6/1. These fractions cannot be simplified further, as the numerator and denominator have no common factors other than 1.
Learn more about series here: brainly.com/question/11346378
#SPJ11
A simple T-beam with bf=600 mm h=500 mmhf=100 mm, bw =300 mm with a span of 3 m, reinforced by 5−20 mm diameter rebar for tension, 2-20mm diameter rebar for compression is to carry a uniform dead load of 20kN/m and uniform live load of 10kN/m. Assuming fc′=21Mpa,fy=415Mpa,d′=60 mm,cc=40 m and stirrups =10 mm, Calculate the cracking moment:
Answers
Answer: cracking moment for the given T-beam is approximately 2.747 kNm.
To calculate the cracking moment for the given T-beam, we need to use the formula:
Mcr = K * (fc' * bd^2)
where Mcr is the cracking moment, K is a coefficient that depends on the reinforcement ratio, fc' is the compressive strength of concrete, b is the width of the beam, and d is the effective depth of the beam.
1. Calculate the effective depth (d):
d = h - hf - cc/2
= 500 mm - 100 mm - 40 mm
= 360 mm
2. Calculate the area of tension reinforcement (As):
As = (5 rebar * π * (20 mm/2)^2)
= 5 * 3.14 * 10^2
= 1570 mm^2
3. Calculate the area of compression reinforcement (Ac):
Ac = (2 rebar * π * (20 mm/2)^2)
= 2 * 3.14 * 10^2
= 628 mm^2
4. Calculate the total area of reinforcement (A):
A = As + Ac
= 1570 mm^2 + 628 mm^2
= 2198 mm^2
5. Calculate the reinforcement ratio (ρ):
ρ = A / (bw * d)
= 2198 mm^2 / (300 mm * 360 mm)
≈ 0.0205
6. Calculate the coefficient (K):
K = 0.6 + (200 / fy)
= 0.6 + (200 / 415 MPa)
≈ 1.07
7. Calculate the cracking moment (Mcr):
Mcr = K * (fc' * bd^2)
= 1.07 * (21 MPa * 300 mm * 360 mm^2)
= 2,746,760 Nmm
= 2.747 kNm
Therefore, the cracking moment for the given T-beam is approximately 2.747 kNm.
To learn more about cracking moment:
https://brainly.com/question/31582619
#SPJ11
A square column of size 400 mm×400 mm, its unsupported length is 5.0 m. Ends of the column are restrained in position and direction. It carries a service axial load of 1200kN. what is the required number of rebar for this column section? Assume concrete grade M20, steel grade Fe415, 20 mm dia. main bar and the column is perfectly axially loaded.
Answers
For the given square column with a size of 400 mm × 400 mm and an unsupported length of 5.0 m, restrained in position and direction, carrying a service axial load of 1200 kN, the required number of 20 mm diameter rebars is 5.
To determine the required number of rebars for the given square column, we need to consider the column's cross-sectional area, the spacing between the rebars, and the area of a single rebar.
1. Calculate the cross-sectional area of the column:
The cross-sectional area of a square column can be calculated by multiplying the length of one side by itself. In this case, the column size is given as 400 mm × 400 mm. To convert it to square meters, divide by 1000. Thus, the cross-sectional area of the column is (400 mm ÷ 1000) × (400 mm ÷ 1000) = 0.16 m².
2. Calculate the required area of steel reinforcement:
The percentage of steel reinforcement required is typically specified based on the concrete grade and the column's dimensions. For M20 concrete grade, the minimum steel reinforcement percentage is 0.85% of the cross-sectional area of the column. Therefore, the required area of steel reinforcement is 0.85% × 0.16 m² = 0.00136 m².
3. Calculate the area of a single rebar:
The area of a rebar can be calculated using the formula A = πr², where A is the area and r is the radius. The diameter of the main bar is given as 20 mm. Therefore, the radius is half the diameter, which is 10 mm. Convert it to meters by dividing by 1000: 10 mm ÷ 1000 = 0.01 m. Using the formula, the area of a single rebar is π × (0.01 m)² = 0.000314 m².
4. Calculate the number of rebars required:
Divide the required area of steel reinforcement by the area of a single rebar to find the number of rebars needed. In this case, 0.00136 m² ÷ 0.000314 m² ≈ 4.34. Since we cannot have a fraction of a rebar, we would round up to the nearest whole number. Therefore, the required number of rebars for this column section is 5.
In summary, for the given square column with a size of 400 mm × 400 mm and an unsupported length of 5.0 m, restrained in position and direction, carrying a service axial load of 1200 kN, the required number of 20 mm diameter rebars is 5.
Know more about cross-sectional area here:
https://brainly.com/question/13029309
#SPJ11
An investor can make an investment in a real estate development and receive an expected cash return of $47,000 at the end of 5 years. Based on a careful study of other investment alternatives, she believes that a 9 percent annual return compounded quarterly is a reasonable return to earn on this investment. Required: How much should she pay for it today? Note: Do not round Intermediate calculations and round your final answer to the nearest whole dollar amount. Present value
Answers
She should pay approximately $30,710.44 today to receive an expected cash return of $47,000 at the end of 5 years, assuming a 9% annual return compounded quarterly.
To calculate the present value of the expected cash return, we can use the formula for present value of a future cash flow:
PV = FV / (1 + r/n)^(n*t)
Where:
PV = Present value
FV = Future value or expected cash return ($47,000)
r = Annual interest rate (9%)
n = Number of compounding periods per year (quarterly, so 4)
t = Number of years (5)
Plugging in the values into the formula:
PV = 47000 / (1 + 0.09/4)^(4*5)
Now, let's calculate the present value:
PV = 47000 / (1 + 0.0225)^(20)
PV = 47000 / (1.0225)^(20)
PV = 47000 / 1.530644
PV ≈ $30,710.44
Therefore, she should pay approximately $30,710.44 today to receive an expected cash return of $47,000 at the end of 5 years, assuming a 9% annual return compounded quarterly.
To know more about value click-
http://brainly.com/question/843074
#SPJ11
(1) What are the points one should have in mind before starting to drive a vehicle? (2) What are the points one should remember when involved in a traffic accident?
Answers
Before driving a vehicle, there are several points to consider:
1. Documents
2. Car Checkup
3. Seating Position
1. Documents - Before getting behind the wheel, ensure that you have your driver's license, vehicle registration, and insurance papers.
2. Car Checkup - Check the car's fluids (brake oil, engine oil, coolant), tires, brakes, lights, and mirrors.
3. Seating Position - Adjust your seat so that you have a clear view of the road and easy access to the pedals
.4. Seat Belts - Always wear a seat belt while driving. It can save your life in the event of an accident.
5. Adjust the Mirrors - Adjust your side and rearview mirrors so that you can see clearly all around you.
6. Driving Rules and Regulations - Be aware of the rules and regulations of the road, as well as any local laws and customs.
7. Traffic Signal - Follow the traffic signals at all times.
The following are the points one should remember when involved in a traffic accident:
1. If you're involved in an accident, don't panic.
2. Turn on the vehicle's hazard lights.
3. Call the police and an ambulance if necessary.
4. Don't argue or get angry with the other driver.
5. Exchange details with the other driver, including name, address, phone number, driver's license number, insurance information, and vehicle registration.
6. Take photos of the accident scene, including the damage to both cars and any injuries.
7. Take note of any witnesses and their contact information.8. Inform your insurance company of the accident as soon as possible.
Know more about driver's license hee:
https://brainly.com/question/26006107
#SPJ11
One should always prioritize safety, remain calm, and follow proper procedures when driving and dealing with traffic accidents.
Before starting to drive a vehicle, there are several points to keep in mind:
1. Familiarize yourself with the vehicle: Ensure you are familiar with the vehicle's controls and features before driving. This includes knowing how to adjust mirrors, use turn signals, operate lights, and engage the emergency brake.
2. Check the condition of the vehicle: Before getting behind the wheel, conduct a pre-drive inspection. Verify that the tires are properly inflated, the brakes are functioning well, the headlights and taillights are working, and there is enough fuel for your intended trip.
3. Buckle up and adjust your seat: Always wear your seatbelt and ensure it is properly fastened before starting the engine. Adjust the seat to a comfortable position that allows you to reach the pedals, see clearly, and have easy access to all the controls.
4. Adjust mirrors and check blind spots: Properly adjust the rearview mirror and side mirrors to minimize blind spots. Remember to also physically check blind spots by turning your head to ensure no vehicles are in those areas.
5. Plan your route: Before driving, plan the route you will take to your destination. Familiarize yourself with the directions and any potential road closures or traffic issues. This will help you stay focused and avoid unnecessary distractions while driving.
When involved in a traffic accident, remember the following points:
1. Ensure safety: First and foremost, prioritize your safety and the safety of others involved. If possible, move to a safe location away from traffic and activate hazard lights to alert other drivers.
2. Check for injuries: Assess yourself and others involved for any injuries. If anyone requires medical attention, call for emergency assistance immediately.
3. Exchange information: Exchange contact, insurance, and vehicle information with the other parties involved. This includes names, phone numbers, addresses, license plate numbers, and insurance policy details.
4. Document the accident: Take pictures or videos of the accident scene, including the damage to all vehicles involved and any relevant road conditions. This documentation can assist with insurance claims and investigations.
5. Notify the authorities and your insurance company: In most cases, it is necessary to report the accident to the police. Additionally, inform your insurance company about the incident as soon as possible.
Learn more about safety
https://brainly.com/question/31562763
#SPJ11
Example 3: A wide rectangular channel with a manning number of 0.02 coveys a discharge of 3m3/s/m. There are two long reaches with different bed slopes. The first reach (upper) has a slope of 1:20 while that for the second reach (lower) is 1:800. Determine: a) The normal depth of flow on each reach b) Critical depth of flow c) Whether a hydraulic jump will occur. d) The conjugate depths of a jump occurred on the lower reach e) The energy head and the power lost in the jump
Answers
The normal depth of flow on the upper reach is 1.53 m and on the lower reach is 4.18 m.
The critical depth of flow on the upper reach is 1.99 m and on the lower reach is 7.72 m.
How to calculate the depth of flowTo calculate depth of flow
We are given the following data:
Discharge (Q) = 3 [tex]m^3/s/m[/tex]
Manning's roughness coefficient (n) = 0.02
Upper reach bed slope (S1) = 1:20
Lower reach bed slope (S2) = 1:800
Normal Depth:
Normal depth can be calculated using the Manning's equation for uniform flow as
[tex]Q = 1/n A(y)^2/3 S^1/2[/tex]
where A is the cross-sectional area of flow and S is the bed slope.
For the upper reach
S1 = 1/20 = 0.05
Area of flow[tex](A_1) = Q / (n S1 yn^2/3) = (3) / (0.02 * 0.05 * yn^2/3)[/tex]
The hydraulic radius (R₁) in terms of depth (y₁) is given by
[tex]R_1 = A_1 / P_1 = (Q / (n S_1 yn^2/3)) / (2 yn / 0.5) = (3 / (0.02 * 0.05 * yn^2/3)) / (4 yn / 0.5)[/tex]
yn₁ = 1.53 m
For the lower reach
S₂ = 1/800 = 0.00125
Area of flow[tex](A_2) = Q / (n S_2 yn^2/3) = (3) / (0.02 * 0.00125 * yn^2/3)[/tex]
The hydraulic radius (R2) in terms of depth (y2) is given by
[tex]R_2 = A_2 / P_2 = (Q / (n S_2 yn^2/3)) / (2 yn / 2) = (3 / (0.02 * 0.00125 * yn^2/3)) / (2 yn / 2)[/tex]
yn₂ = 4.18 m
Thus, the normal depth of flow on the upper reach is 1.53 m and on the lower reach is 4.18 m.
Critical Depth:
Critical depth can be calculated using the following equation:
[tex]yc = (Q^2 / g S)^1/3[/tex]
where g is the acceleration due to gravity.
For the upper reach
[tex]yc_1 = (3^2 / (9.81 * 0.05))^(1/3) = 1.99 m[/tex]
For the lower reach
[tex]yc_2 = (3^2 / (9.81 * 0.00125))^(1/3) = 7.72 m[/tex]
Hence, the critical depth of flow on the upper reach is 1.99 m and on the lower reach is 7.72 m.
Hydraulic Jump:
It can calculated using the following equation:
[tex]Fr = V / (g yn)^1/2[/tex]
where V is the velocity of flow.
For the upper reach
[tex]V_1 = Q / A1 = (3) / ((0.02 * 0.05 * 1.53^2/3)) = 2.74 m/s[/tex]
[tex]Fr_1 = V1 / (g yn1)^1/2 = 2.74 / (9.81 * 1.53)^1/2 = 0.59[/tex]
Since Fr1 is less than 1, a hydraulic jump will not occur on the upper reach.
For the lower reach, the velocity can be calculated as
[tex]V_2 = Q / A2 = (3) / ((0.02 * 0.00125 * 4.18^2/3)) = 5.93 m/s[/tex]
[tex]Fr_2 = V2 / (g yn2)^1/2 = 5.93 / (9.81 * 4.18)^1/2 = 1.34[/tex]
Since Fr2 is greater than 1, a hydraulic jump will occur on the lower reach.
Conjugate Depths of Jump:
The conjugate depths of the jump (y₁ and y₂) can be calculated using the following equations:
[tex]y_1 = yc^2 / (4 yn2)\\y_2 = 2.5 yn2 - 1[/tex]
Substituting the values
[tex]y_1 = (7.72^2) / (4 * 4.18) = 4.47 m\\y_2 = 2.5 * 4.18 - 1 = 9.45 m[/tex]
Therefore, the conjugate depths of the jump are 4.47 m and 9.45 m.
Energy Head and Power Loss in Jump:
The energy head before and after the jump can be calculated as
[tex]E_1 = y_1 + V_1^2 / (2g)\\E_2 = y_2 + V_2^2 / (2g)[/tex]
Substituting the values
[tex]E_1 = 4.47 + (2.74^2) / (2 * 9.81) = 5.58 m\\E_2 = 9.45 + (5.93^2) / (2 * 9.81) = 12.78 m[/tex]
The energy head lost in the jump is:
ΔE = E₁ - E₂2 = 5.58 - 12.78 = -7.20 m
Since the energy head is lost, the power loss in the jump can be calculated as
P = ΔE × Q = -7.20 × 3 = -21.6 kW
Therefore, the energy head lost in the jump is 7.20 m and the power loss is 21.6 kW.
Learn more on hydraulic jump on https://brainly.com/question/28507220
#SPJ4
Level 5 taping provides a very smooth surface by? a) One coat of mud and tape 4" knife b) Two coats of mud and tape 4" and 6" knifes c) Three coats of mud with tape 4", 6" and then 8-12" knifes d) Entirely skim coating the wall board to fill all the pores
Answers
The correct option (c). Three coats of mud with tape 4", 6" and then 8-12" knives.
Level 5 taping provides a very smooth surface by three coats of mud with tape 4", 6" and then 8-12" knives.
The Level 5 Taping process involves covering the entire surface of the wallboard with three separate coats of joint compound.
The first coat of joint compound is used to embed the tape and eliminate any bubbles or wrinkles in the tape. For the second coat, the drywall contractor uses a six-inch joint knife to apply a thin layer of joint compound over the tape.
This coat should be allowed to dry completely.
The third and final coat is where the smoothness comes in. This coat involves using an eight to twelve-inch joint knife to apply a thin layer of joint compound over the entire surface of the wallboard.
This coat should be allowed to dry completely. After the third coat is completely dry, the wallboard is sanded smooth, and the dust is removed before the primer and paint are applied.
To know more about coats visit:
https://brainly.com/question/2750661
#SPJ11
Simon recently received a credit card with a 20% nominal interest rate. With the card, he purchased an Apple iPhone 7 for $420.00. The minimum payment on ihe card is only $20 per month. intermediate calculations. Round your answer to the nearest whole number. month(s) b. If Simon makes monthly payments of $60, how many months will it be before he pays off the debt? Do not round intermediate calcular answer to the nearest whole number. month(s) Round your answer to the nearest cent. $
Answers
It will take Simon 25 months to pay off the debt with a minimum payment of $20 per month. It will take Simon 8 months to pay off the debt with monthly payments of $60. The total amount to be paid will be $504.00.
a. To find the number of months it will take to pay off the debt with a minimum payment of $20 per month, we need to determine the total amount of interest and the total amount paid.
First, let's calculate the interest charged on the balance of $420.00:
Interest = Balance * Interest Rate = $420.00 * 20% = $84.00
Next, let's calculate the total amount paid:
Total Amount Paid = Balance + Interest = $420.00 + $84.00 = $504.00
Now, we can calculate the number of months it will take to pay off the debt with a minimum payment of $20 per month:
Number of Months = Total Amount Paid / Minimum Payment = $504.00 / $20 = 25.2
Rounded to the nearest whole number, it will take Simon 25 months to pay off the debt with the minimum payment.
b. If Simon makes monthly payments of $60, we can calculate the number of months it will take to pay off the debt using the same approach:
Total Amount Paid = Balance + Interest = $420.00 + $84.00 = $504.00
Number of Months = Total Amount Paid / Monthly Payment = $504.00 / $60 = 8.4
Rounded to the nearest whole number, it will take Simon 8 months to pay off the debt with monthly payments of $60.
The rounded total amount to be paid will be $504.00.
Learn more about pay off the debt
brainly.com/question/25996129
#SPJ11
Consider the ellipsoid 2x2+3y2+z2=202x2+3y2+z2=20. Find all the points where the tangent plane to this ellipsoid is parallel to the plane 3y−4x−3z=03y−4x−3z=0.
Answers
The points where the tangent plane to the ellipsoid 2x^2 + 3y^2 + z^2 = 20 is parallel to the plane 3y - 4x - 3z = 0 are (-√(10/13), √(20/13), -3√(10/39)) and (√(10/13), -√(20/13), 3√(10/39)).
Consider the ellipsoid 2x^2 + 3y^2 + z^2 = 20.
We are supposed to find all the points where the tangent plane to this ellipsoid is parallel to the plane 3y - 4x - 3z = 0.
Let F(x, y, z) = 2x^2 + 3y^2 + z^2 - 20.
From this equation, the gradient of F(x, y, z) is given by
Fx = 4x, Fy = 6y and Fz = 2z.
Let (x0, y0, z0) be a point on the ellipsoid 2x^2 + 3y^2 + z^2 = 20.
We need to find all the values of (x0, y0, z0) such that the gradient of F at (x0, y0, z0) is parallel to the plane 3y - 4x - 3z = 0 which means the normal vector to the tangent plane at (x0, y0, z0) is parallel to the normal vector of the plane 3y - 4x - 3z = 0.
The normal vector of the plane 3y - 4x - 3z = 0 is given by N = < -4, 3, -3 >.
The gradient of F at (x0, y0, z0) is given by F'(x0, y0, z0) = < 4x0, 6y0, 2z0 >.
These two vectors are parallel if and only if
F'(x0, y0, z0) = λN
where λ is a scalar.
Substituting the values, we get 4x0 = -4λ, 6y0 = 3λ and 2z0 = -3λ.
We know that the point (x0, y0, z0) lies on the ellipsoid 2x^2 + 3y^2 + z^2 = 20.
Substituting the values, we get2(-λ)^2 + 3(λ)^2 + (-3/2λ)^2 = 20
Simplifying this equation, we get 13λ^2/2 = 20.
Solving for λ, we get λ = ± √(40/13).
Substituting λ = √(40/13), we get the point on the ellipsoid as(x0, y0, z0) = (-√(10/13), √(20/13), -3√(10/39)).
Similarly, substituting λ = - √(40/13), we get the point on the ellipsoid as(x0, y0, z0) = (√(10/13), -√(20/13), 3√(10/39)).
Therefore, the points where the tangent plane to the ellipsoid 2x^2 + 3y^2 + z^2 = 20 is parallel to the plane 3y - 4x - 3z = 0 are (-√(10/13), √(20/13), -3√(10/39)) and (√(10/13), -√(20/13), 3√(10/39)).
Learn more about tangent plane
https://brainly.com/question/33705650
#SPJ11
The two points where the tangent plane to the ellipsoid is parallel to the plane 3y − 4x − 3z = 0 are (-2, 2, 3) and (2, -2, -3).
The equation of the ellipsoid is given by 2x^2 + 3y^2 + z^2 = 20.
To find the points where the tangent plane to the ellipsoid is parallel to the plane 3y − 4x − 3z = 0, we can use the fact that the normal vectors of the tangent plane and the given plane are parallel.
First, find the gradient vector of the ellipsoid by taking the partial derivatives with respect to x, y, and z:
dF/dx = 4x
dF/dy = 6y
dF/dz = 2z
Next, we equate the gradient vector of the ellipsoid to a scalar multiple of the normal vector of the given plane:
4x = λ(−4)
6y = λ(3)
2z = λ(−3)
Solving these equations simultaneously, we get:
x = −λ
y = λ
z = −(3/2)λ
Substituting these values into the equation of the ellipsoid, we get:
2(−λ)^2 + 3(λ)^2 + (−(3/2)λ)^2 = 20
Simplifying the equation, we get:
λ^2 = 4
Taking the square root of both sides, we find two values for λ: λ = 2 and λ = −2.
Substituting these values back into the equations for x, y, and z, we get the points where the tangent plane is parallel to the given plane:
Point 1: (x, y, z) = (−2, 2, 3)
Point 2: (x, y, z) = (2, −2, −3)
Therefore, the two points where the tangent plane to the ellipsoid is parallel to the plane 3y − 4x − 3z = 0 are (-2, 2, 3) and (2, -2, -3).
Learn more about ellipsoid
https://brainly.com/question/33590847
#SPJ11
help?????????????????????????????//
Answers
Answer: 729 cubic yards
Step-by-step explanation:
To calculate the volume of a cube,
we need to multiply its side 3 times, so
9×9×9=729.
A person is riding a bike at 20 miles per hour and starts to slow down producing a constant deceleration of 5 miles per hr². (a) (3 pts) How much time elapses before the bike stops? (b) (4 pts) What is the distance traveled before the bike comes to a stop?
Answers
a. The bike will take 4 hours to stop
b. The bike will travel a distance of 40 miles before coming to a halt.
(a) The bike will stop when its velocity reaches 0. Using the equation v = u + at, where v is the final velocity, u is the initial velocity, a is the acceleration, and t is the time, we can rearrange the equation to solve for t. In this case, u = 20 mph, a = -5 mph² (negative because it's deceleration), and v = 0.
0 = 20 - 5t
5t = 20
t = 4 hours
(b) To calculate the distance traveled, we can use the equation s = ut + 0.5at², where s is the distance traveled. Plugging in the values, u = 20 mph, a = -5 mph², and t = 4 hours:
s = 20 * 4 + 0.5 * (-5) * (4)²
s = 80 - 0.5 * 5 * 16
s = 80 - 40
s = 40 miles
Therefore, the bike will take 4 hours to stop and will travel a distance of 40 miles before coming to a halt.
Learn more about miles here: brainly.com/question/28161927
#SPJ11
A rotary pump draws oil from (tank 1) and delivers it into (tank2), the level in (tank 1) is 3 m below the base of (tank 2) and the level in (tank 2) is 6 m. If the pump sits 2 m above the base of (tank 2) and discharges into the side of the tank 2 at a height of 4 m, what is the static discharge head?
Answers
Given the distance between the oil source tank (Tank 1) and oil discharge tank (Tank 2) is 3m and the height difference between the two tanks is 6m. It is also known that the pump is placed 2m above the base of Tank 2. This makes the discharge height of the pump 4m. The static discharge head of the rotary pump needs to be calculated
The static discharge head of a rotary pump is calculated using the formula, Static discharge head = height of tank 2 + elevation difference between the tanks + discharge height of the pump - height of the pump above the base of tank 2.The following are the given values in the problem: Height of tank 2 = 6 m. Elevation difference between the tanks = 3 m. Height of the pump above the base of tank 2 = 2 m. Discharge height of the pump = 4 m. Using the formula for static discharge head, we can calculate it as follows: Static discharge head = height of tank 2 + elevation difference between the tanks + discharge height of the pump - height of the pump above the base of tank 2. Static discharge head = 6 + 3 + 4 - 2. Static discharge head = 11Therefore, the static discharge head of the rotary pump is 11 m. Height of tank 2 = 6 m. Elevation difference between the tanks = 3 m. Height of the pump above the base of tank 2 = 2 m. Discharge height of the pump = 4 m. To calculate the static discharge head, we can use the formula, Static discharge head = height of tank 2 + elevation difference between the tanks + discharge height of the pump - height of the pump above the base of tank 2.The height of tank 2 is 6 m, the elevation difference between the tanks is 3 m, the discharge height of the pump is 4 m, and the height of the pump above the base of tank 2 is 2 m. Using these values, we can calculate the static discharge head as follows: Static discharge head = height of tank 2 + elevation difference between the tanks + discharge height of the pump - height of the pump above the base of tank 2Static discharge head = 6 + 3 + 4 - 2Static discharge head = 11Thus, the static discharge head of the rotary pump is 11 m.
In conclusion, the static discharge head of the rotary pump that draws oil from tank 1 and delivers it into tank 2 is 11 m.
learn more about Static discharge visit:
brainly.com/question/8338731
#SPJ11
Consider the elementary exothermic irreversible liquid-phase hydration reaction: A+W →B where W represents water carried out in a batch reactor operating under adiabatic of the solution is 0.980 g cm. The molar mass of Ais 76 g mor. The initial temperature is 298 K. Other data are as follows: k 9.0 1020 exp 19230 Lgmole-1 s-1 T[K] T AHrx = -90,000 J gmole-1 at 298 K Component Cpi (J/gmole K) A 289.8 w 75.6 B 366.6 a. (10) Determine the reactor temperature when the conversion reaches 80%. b. (15) How long does it take to achieve this conversion? b. (5) What will be the corresponding temperature and residence time if instead we use an adiabatic plug flow reactor? Discuss your results.
Answers
The reactor temperature and time required to achieve 80% conversion in the batch reactor operating under adiabatic conditions and the corresponding temperature and residence time.
Reactor Temperature calculation
The conversion formula is given as;
α = (Co - C)/ Co
= 1 - C/Co
Let α = 0.8
Co = 0.980g/cm³
C = Co (1-α)
= 0.980(0.2)
= 0.196 g/cm³
Since the reaction is exothermic, we use the Levenspiel equation and the energy balance equation.
The Levenspiel equation is given as:
α = [1 + K(Cao - Co)τ] - 1/2 where K = 9.0 × 1020 exp(-19230/T) L/gmol s,
Cao = 0.980 g/cm³, and Co = 0.196 g/cm³
For T = 298K, K = 9.0 × 1020 exp(-19230/298) L/gmol
sK = 2.143 × 109 L/gmol s
Plugging in these values, we get:
0.8 = [1 + (2.143 × 109(0.980 - 0.196)τ)]-1/2
Solving for τ, we have:τ = 1.7 × 10-8 sb)
Time required to achieve 80% conversion τ = 1.7 × 10-8 s
Volume of the reactor = 1 L
Co = 0.980 g/cm³
V = 1000 cm³
Molecular weight of A, MA = 76 g/mol
Specific heat capacity of A, CpA = 289.8 J/gmol K
T is the temperature difference, T = T - T0, where T0 = 298 K
CpAΔT = -AHrxαSo,
ΔT = -AHrxα/CpA
= -90,000 × 0.8/289.8
= -248 K
The reactor temperature, T = T0 + ΔT = 298 - 248 = 50 K
The problem is talking about the hydration reaction of A+W→B, which is a liquid-phase, irreversible, exothermic reaction. We are given the initial concentration, conversion, activation energy, rate constant, enthalpy of reaction, and specific heat capacity of the components.
Our task is to determine the reactor temperature and time required to achieve 80% conversion in the batch reactor operating under adiabatic conditions and the corresponding temperature and residence time if an adiabatic plug flow reactor is used.
For the batch reactor operating under adiabatic conditions, we use the Levenspiel equation and the energy balance equation to determine the temperature and time required to achieve the conversion. The Levenspiel equation is used to relate the concentration and time while the energy balance equation is used to relate the temperature and heat transfer.
We use the conversion formula to determine the initial concentration of A and the concentration of A at 80% conversion. We then plug these values into the Levenspiel equation to determine the time required. We also use the enthalpy of reaction and specific heat capacity to determine the temperature difference and the reactor temperature.
The residence time is the time taken for the reaction to complete in the reactor. For the batch reactor, the residence time is equal to the time required to achieve the conversion. For the adiabatic plug flow reactor, we use the same method to calculate the residence time and temperature as for the batch reactor but we also use the plug flow model to account for the changes in concentration and temperature along the reactor.
In conclusion, we have determined the reactor temperature and time required to achieve 80% conversion in the batch reactor operating under adiabatic conditions and the corresponding temperature and residence time if an adiabatic plug flow reactor is used. We used the Levenspiel equation and the energy balance equation to determine the temperature and time required to achieve the conversion in the batch reactor. We also used the plug flow model to account for the changes in concentration and temperature along the adiabatic plug flow reactor.
To know more about equation visit:
brainly.com/question/29657983
#SPJ11
"
The band is breaking up and Rob, Sue, Tim and Vito each want the tourbus. Using the method of sealed bids, Rob bids $2500, Sue bids$5400, Tim bids $2400, and Vito bids $6200 for the bus. SinceVito'
Answers
Rob will receive approximately $1133.33 from Vito.
To determine how much money Rob will get from Vito, we need to calculate the fair division of the bids among the four individuals. Since Vito won the bus with the highest bid, he will compensate the others based on their bids.
The total amount of compensation that Vito needs to pay is the sum of all the bids minus the winning bid. Let's calculate it:
Total compensation = (Rob's bid + Sue's bid + Tim's bid) - Vito's bid
= ($2500 + $5400 + $2400) - $6200
= $10300 - $6200
= $4100
Now, we need to determine the amount of money each person will receive. To calculate the fair division, we divide the total compensation by the number of people (4) excluding Vito, since he won the bid.
Rob's share = (Rob's bid) - (Total compensation / Number of people)
= $2500 - ($4100 / 3)
≈ $2500 - $1366.67
≈ $1133.33
Thus, the appropriate answer is approximately $1133.33 .
Learn more about money:
https://brainly.com/question/24373500
#SPJ11
Example 2 Water is placed in a piston-cylinder device at 20°C, 0.1MPa. Weights are placed on the piston to maintain a constant force on the water as it is heated to 400°C. How much work does the wat
Answers
The volume of water will remain constant, thus the work done by the water is zero.
Given that a water is placed in a piston-cylinder device at 20°C, 0.1 MPa.
Weights are placed on the piston to maintain a constant force on the water as it is heated to 400°C.
To find out how much work does the water do, we can use the formula mentioned below:
Work done by the water is given by,
W = ∫ PdV
where P = pressure applied on the piston, and
V = volume of the water
As we know that the force applied on the piston is constant, therefore the pressure P is also constant. Also, the weight of the piston is balanced by the force applied by the weights, thus there is no additional external force acting on the piston.
Therefore, the volume of the water will remain constant, thus the work done by the water is zero.
Know more about the piston-cylinder device
https://brainly.com/question/22587059
#SPJ11
According to the NSW Waste management hierarchy,
Answers
The NSW Waste Management Hierarchy provides a framework for prioritizing waste management practices.
What is the purpose of the NSW Waste Management Hierarchy?The NSW Waste Management Hierarchy is a guide that outlines the preferred order of waste management practices in New South Wales, Australia. It is designed to promote waste reduction, resource recovery, and minimize the environmental impact of waste. The hierarchy consists of the following priority order:
1. Avoidance: The most effective way to manage waste is to prevent its generation by reducing consumption and implementing sustainable practices.
2. Reduction: If waste cannot be avoided, efforts should focus on minimizing its quantity through efficient use of resources and materials.
3. Reuse: Promote the reuse of products and materials to extend their lifespan and reduce the need for new production.
4. Recycling: Recycling involves the collection and processing of waste materials to produce new products or raw materials.
5. Recovery: Energy recovery involves extracting energy from waste through processes like incineration or anaerobic digestion.
6. Disposal: Disposal should be the last resort and should only be used for waste that cannot be managed through any other means.
Learn more about Waste Management Hierarchy
brainly.com/question/33437863
#SPJ11