The criteria for matching streams above the pinch for designing heat exchangers is to make sure that the hot stream and the cold stream are both having the same temperature. The criteria for matching streams below the pinch is to make sure that the hot stream and the cold stream have the same heat capacity.
These criteria are needed to ensure that there is an efficient heat exchange, meaning that the hot stream will give up most of its heat to the cold stream. In order for this to occur, it is essential that the temperature and heat capacity of the two streams are similar. If the temperatures of the hot and cold streams are too different, the efficiency of the heat exchange will be greatly reduced.
Similarly, if the heat capacities of the hot and cold streams are too different, the heat exchange will not be efficient. Thus, these criteria are necessary for efficient heat exchange.
You can learn more about heat exchangers at: brainly.com/question/22595817
#SPJ11
explain the relationship between the concrete compressive strength and its flexural strength and splitting tensile strength.
The relationship between the concrete compressive strength and its flexural strength and splitting tensile strength is that; these strengths are interrelated and their values are dependent on one another.
The compressive strength of concrete is defined as the maximum compressive load that can be applied on a test specimen, to fail in compression. It is expressed in MPa or psi. It is one of the most important properties of concrete and is essential in designing a structure because it defines the concrete’s ability to resist compressive stresses.
A flexural strength test is performed on concrete to determine the strength of concrete in resisting bending stresses. In other words, the test determines the ability of the concrete to withstand bending stresses without cracking. A flexural strength test is important in the design of structural elements like beams, slabs, and other such components that are subjected to bending forces.
The splitting tensile strength of concrete is determined by applying a load on a cylindrical or cubical test specimen of concrete. It is the ability of the concrete to withstand tensile forces that tend to split or rupture the test specimen. It is an important property of concrete because it defines the concrete’s ability to resist tension and shear forces.
The relationship between these three strengths of concrete is that they are interrelated and their values are dependent on one another. In general, the compressive strength of concrete is higher than its flexural strength and splitting tensile strength. However, flexural strength and splitting tensile strength are important in determining the overall strength of concrete, and they are used in the design of structural elements like beams, slabs, and other such components.
You can learn more about compressive strength at: brainly.com/question/15230572
#SPJ11
a stepped uniaxial br is subjected to forces the length and area of cross sections of the two elements are write thees stiffness matric
A stepped uniaxial bar is subjected to forces. The length and area of cross-sections of the two elements are asked to be written. The stiffness matrix of the given information is to be calculated.
Consider a stepped uniaxial bar subjected to forces as shown in the below diagram. The above bar has two different areas of cross-section and lengths. Hence, the bar can be divided into two elements with different areas and lengths.
Let us consider Element 1:
Here, [tex]l_1[/tex] = Length of element 1
[tex]A_1[/tex] = Area of cross-section of element 1
Let [tex]P_1[/tex] and [tex]P_2[/tex] be the forces applied on Element 1 and Element 2 respectively.
In general, the element stiffness matrix can be written as [tex]k = AE / Le[/tex], where A is the area of the cross-section, E is the modulus of elasticity, and Le is the length of the element.
Let us calculate the stiffness matrix for Element 1. The stiffness matrix of Element 1, [tex]k_1[/tex] is given by:
[tex]k_1 = (A_1E_1 / l_1) * [1, -1; -1, 1][/tex]
Let us consider Element 2:
Here, [tex]l_2[/tex] = Length of element 2
[tex]A_2[/tex] = Area of cross-section of element 2
The stiffness matrix of Element 2, [tex]k_2[/tex] is given by:
[tex]k_2 = (A_2E_2 / l_2) * [1, -1; -1, 1][/tex]
Now, we need to find the stiffness matrix of the complete bar. Let us consider k as the stiffness matrix of the complete bar. Then, [tex]k = [k_1 + k_2][/tex] is the stiffness matrix of the complete bar.
The complete stiffness matrix of the given problem is given by: [tex]k = [A_1E_1/l_1 + A_2E_2/l_2] * [1, -1; -1, 1][/tex]
Hence, the stiffness matrix of the given problem is given by [tex][A_1E_1/l_1 + A_2E_2/l_2] * [1, -1; -1, 1].[/tex]
Learn more about stiffness matrix here:
https://brainly.com/question/30638369
#SPJ11
Kelvin contact resistance test structure in Fig. P3. 19, it is usually assumed that the voltmeter has very high input resistance and there is negligible voltage drop along the voltage measurement arm
In the Kelvin contact resistance test structure in Fig. P3.19, it is usually assumed that the voltmeter has very high input resistance and there is negligible voltage drop along the voltage measurement arm.
This assumption is made because the purpose of the Kelvin contact resistance test is to measure the resistance of a contact without including the resistance of the contact leads.To achieve this, the current is passed through the current leads, and the voltage is measured using the voltage leads. However, if the voltage leads have any resistance, this will add to the measured resistance value, making it inaccurate. To avoid this, the Kelvin contact resistance test structure uses two sets of voltage leads, one to carry the current and another to measure the voltage, so that any resistance in the measurement leads is not included in the measured resistance value.By assuming that the voltmeter has very high input resistance and there is negligible voltage drop along the voltage measurement arm, the Kelvin contact resistance test structure ensures that any resistance in the measurement leads is insignificant compared to the resistance of the contact being measured. This allows for accurate measurement of contact resistance and is a common technique used in electrical testing.for more such question on voltage
https://brainly.com/question/1176850
#SPJ11
you were unable to attend all of the training, but your coworker has offered to fill you in on the details that you missed. identify which of the following statements your coworker is likely to indicate as diversity principles discussed during your absence. check all that apply.
The diversity principles include equity, inclusion, diversity, intersectionality, and cultural competency.
However, some common diversity principles that are often discussed include:
Equity: ensuring everyone has access to the same opportunities and resources, regardless of their background or identity. Inclusion: creating a sense of belonging where everyone feels valued, respected, and supported. Diversity: recognizing and embracing differences in race, ethnicity, gender, age, religion, ability, and other characteristics. Intersectionality: recognizing that individuals have multiple identities that interact and influence their experiences. Cultural competency: having the knowledge, skills, and awareness to effectively interact with individuals from diverse backgrounds.To learn more about diversity principles:
https://brainly.com/question/11541955
#SPJ11
true or false: since liquid can be considered as incompressible, the volume flow rates into and out of a steady flow device will remain constant.
Answer:
True
Explanation:
Since liquid can be considered as incompressible, the volume flow rates into and out of a steady flow device will remain constant. True, For a steady, incompressible flow, since the density is constant, it implies that the total volumetric flow rates entering and leaving a control volume are the same.
when servicing a driveshaft, technician a says that its a good idea to tape the u-joint caps to prevent them from coming off. technician b says that needle bearings are used with this type of u-joints. which technician is correct?
Both technicians A and B are correct, and their recommendations can help ensure that the driveshaft is serviced safely and effectively.
Technician A is suggesting that it is a good idea to tape the U-joint caps to prevent them from coming off. This can be a good practice as it can help to prevent the caps from falling off during the disassembly of the driveshaft or during transportation, which can result in the loss of needle bearings or damage to the U-joint.
Technician B is stating that needle bearings are used with this type of U-joints. This is also correct as most modern U-joints use needle bearings to allow for smooth rotation of the U-joint.
Learn more about maintenance of a driveshaft:
https://brainly.com/question/15188861
#SPJ11
Find the resistivity of gold at room temperature. Use the following information:
Free electron density of gold = 5.90×1028,5.90×1028,
Fermi energy of gold = 8.86×10−19,8.86×10−19,
Mass of electron = 9.11×10−31,9.11×10−31,
Charge of an electron = −1.6×10−19−1.6×10−19, and
Mean free path of electron in gold = 3.45×10−8
The resistivity of gold at room temperature is approximately 2.44×10⁻⁸ Ωm
To find the resistivity of gold at room temperature, you can use the formula for resistivity, which is given by:
Resistivity (ρ) = m / (n * e² * τ)
where m is the mass of an electron, n is the free electron density, e is the charge of an electron, and τ is the mean free time between electron collisions. We can calculate τ using the mean free path (λ) and Fermi velocity (vF), given by:
τ = λ / vF
To calculate the Fermi velocity, we can use the formula:
vF = sqrt(2 * EF / m)
where EF is the Fermi energy of gold. Let's now calculate the resistivity step by step.
1. Calculate the Fermi velocity:
vF = sqrt(2 * 8.86×10⁻¹⁹ J / 9.11×10⁻³¹ kg)
vF ≈ 1.39×10⁶ m/s
2. Calculate the mean free time between electron collisions:
τ = 3.45×10⁻⁸ m / 1.39×10⁶ m/s
τ ≈ 2.49×10⁻¹⁵ s
3. Calculate the resistivity of gold at room temperature:
ρ = (9.11×10⁻³¹ kg) / (5.90×10²⁸ m⁻³ * (1.6×10⁻¹⁹ C)² * 2.49×10⁻¹⁵ s)
ρ ≈ 2.44×10⁻⁸ Ωm
So, the resistivity of gold at room temperature is approximately 2.44×10⁻⁸ Ωm.
Learn more about "resistivity " at: https://brainly.com/question/30799966
#SPJ11
Please give a detail explanation, thank you
1) When solving the impact problems, we should always assume that during an impact between two bodies, there is no permanent deformation in the bodies.
True or false
2) If a semi-truck collides head-on with a mini car, which one will exert more force?
Semi-truck on the mini car
Mini car on the semi-truck
There is no force exerted
Both vehicles will exert equal force
The given statement "When solving the impact problems, we should always assume that during an impact between two bodies, there is no permanent deformation in the bodies" is False and there is usually some amount of permanent deformation during an impact when semi-truck collides head-on with a mini car.
The statement is False because In reality, there is usually some amount of permanent deformation that occurs during an impact, especially if the impact is severe. However, in many cases, the amount of deformation may be negligible or can be ignored for simplicity in calculations.Therefore the statement is False.
If a semi-truck collides head-on with a mini car then According to Newton's Third Law of Motion, every action has an equal and opposite reaction. Therefore, both the semi-truck and the mini car will exert equal force on each other during a head-on collision. The force experienced by each vehicle will depend on factors such as their mass, speed, and the duration of the impact. However, it is likely that the semi-truck, being much larger and heavier than the mini car, will experience less of a change in velocity than the mini car and therefore will exert more force on the smaller vehicle.
To practice more questions on force:
https://brainly.com/question/12970081
#SPJ11
inside my Apt the built in ceiling lights show the "Ripple Effect" what do I do this is a fire hazard also my thermostate ripples.
If the built-in ceiling lights and thermostat in your apartment are showing a ripple effect, this may indicate an issue with your electrical wiring or with the light fixtures and thermostat themselves.
What is the Ripple Effect about?If your built-in ceiling lights are showing a ripple effect and your thermostat is also affected, it could indicate a problem with the electrical wiring in your apartment. This could potentially be a fire hazard and should be addressed immediately.
Here are some steps you can take:
Turn off the power to the affected lights and thermostat by flipping the circuit breaker that controls them. This will prevent any electrical current from flowing through the wiring and reduce the risk of a fire.Contact a licensed electrician to inspect the wiring in your apartment. They can identify any issues with the wiring and make any necessary repairs to ensure your safety.Avoid using the affected lights and thermostat until the issue has been resolved. Using them could potentially cause a fire or other electrical hazards.Therefore, , it is important to take any electrical issues in your apartment seriously and seek professional help to address them promptly.
Learn more about Ripple Effect from
https://brainly.com/question/27988734
#SPJ1
can a building get in trouble for having frequent pulled fire alarms and not doing anything to fix them
Yes, a building can get in trouble for having frequent pulled fire alarms and not doing anything to fix them. This is because it is a violation of fire safety regulations and puts the safety of the building occupants at risk.
The specific consequences for the building will depend on the laws and regulations of the jurisdiction where the building is located. In many places, building owners and managers are required by law to maintain their fire alarm systems in good working order and to take steps to prevent false alarms. Failure to comply with these regulations can result in fines, legal action, or other penalties.
Additionally, if the building is part of a larger complex or managed by a larger organization, repeated false alarms may also result in negative consequences for the organization as a whole, including damage to its reputation and potential liability for any resulting damages or injuries.
To learn more about fire safety regulations:
https://brainly.com/question/3436948
#SPJ11
the composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. the crosssectional area and modulus of elasticity in the figure. neglect the size of the collars at b and c. determine the i. t following: he normal stress in each section ii. t he . displacement of b with respect to c iii. the d of the composite shaft isplacement of end a with respect to end d . . for each section are shown
I. Normal Stress in Each Section:
- Aluminum: σ = (P × L) / (A × E) = (100 × 0.5) / (1 × 7.3 x 10^10) = 6.85 MPa
- Copper: σ = (P × L) / (A × E) = (100 × 0.2) / (0.25 × 1.7 x 10^11) = 8.82 MPa
- Steel: σ = (P × L) / (A × E) = (100 × 0.3) / (0.5 × 2 x 10^11) = 3 MPa
II. Displacement of B with Respect to C:
ΔBC = (P × L^3) / (E × A) = (100 × 0.2^3) / (2 x 10^11 × 0.5) = 0.002 mm
III. Displacement of A with Respect to D:
ΔAD = (P × L^3) / (E × A) = (100 × 0.5^3) / (7.3 x 10^10 × 1) = 0.009 mm
Given data: The composite shaft consists of aluminum, copper, and steel sections. The cross-sectional area and modulus of elasticity in the figure are given. Neglect the size of the collars at b and c. Determine the following: i. The normal stress in each section ii. The displacement of b with respect to ciii.
The displacement of end a with respect to end d The given shaft is subjected to loading as shown in the figure, which is a simple case of compound stress where the stress is induced due to the combined effect of the normal stress σ and shear stress τ.σ is a longitudinal stress acting along the axis of the shaft.
You can read more about normal stress at https://brainly.com/question/17135312
#SPJ11
assuming that the longest stage of 5-stage pipeline requires 0.6ns, and pipeline register delay is 0.1ns, calculate the clock cycle time of 5-stage pipeline and 10-stage pipeline.
The 10-stage pipeline's clock cycles would take 1.5ns to finish on average, which is 1.5ns longer than the 5-stage pipeline's.
To calculate the clock cycle time of a 5-stage pipeline and a 10-stage pipeline, we need to consider the time required for each stage and the pipeline register delay.
For a 5-stage pipeline with a longest stage of 0.6ns and a pipeline register delay of 0.1ns, the total clock cycle time would be:
Clock cycle time = longest stage time + pipeline register delay = 0.6ns + 0.1ns = 0.7ns
This means that each clock cycle in the pipeline would take 0.7ns to complete.
For a 10-stage pipeline with the same longest stage time and pipeline register delay, the total clock cycle time would be:
Clock cycle time = longest stage time + (pipeline register delay x (number of pipeline stages - 1)) = 0.6ns + (0.1ns x 9) = 1.5ns
This means that each clock cycle in the 10-stage pipeline would take 1.5ns to complete, which is longer than the 5-stage pipeline due to the additional pipeline stages.
It is worth noting that while longer pipelines can potentially increase performance by allowing for higher clock rates, they can also increase the risk of pipeline hazards and decrease overall efficiency due to increased latency and complexity.
To learn more about clock cycles refer to:
brainly.com/question/29673495
#SPJ4
how does the sovent drainage and waste system operate without the venting piping used in traditional systems?
The solvent drainage and waste system operates without venting piping by using a combination of air flow and pressure.
Instead of relying on venting piping to exhaust fumes and waste, the system takes in air from the atmosphere and circulates it through the system with a blower or compressor. This creates a pressure difference that drives the solvent out of the system, taking any remaining waste with it. The pressure also keeps odors from escaping and prevents the system from backflowing.
Drainage is the removal of a mass of water either naturally or artificially from the surface or subsurface from a place.
Learn more about drainage : https://brainly.com/question/831589
#SPJ11
What type of hazard is electrical equipment?
Electrical equipment can pose several types of hazards, including electrical shock, burns, fires, and explosions.
Electrical shock can occur if a person comes into contact with an electrical current. Even low voltage currents can be dangerous and potentially fatal. Burns can also occur if a person comes into contact with a hot surface, such as a light bulb or a heating element.
Electrical equipment can also start fires if it overheats or if electrical wiring becomes damaged. This can lead to a risk of property damage, injury, or even death.
Explosions can occur if there is a buildup of electrical energy in a confined space, such as a transformer, capacitor, or battery. This can lead to a sudden release of energy that can cause an explosion, resulting in injury or property damage.
To minimize these hazards, it is important to properly install and maintain electrical equipment, follow safety procedures, and provide adequate training for those who use the equipment. Regular inspections, maintenance, and upgrades can help ensure that electrical equipment is in good working order and that potential hazards are identified and addressed.
To know more about Electrical equipment, visit: brainly.com/question/14144270
#SPJ4
the most commonly installed type of fire sprinkler systems are? pre-action systems dry-pipe systems wet-pipe systems deluge systems
The most commonly installed type of fire sprinkler system is the wet-pipe system. In a wet-pipe system, the pipes are filled with water and are pressurized so that when the heat of a fire activates the sprinkler head, water is released onto the fire.
Pre-action systems use a separate water line to fill the pipes with water and need to be triggered by another type of detector such as smoke or heat, while dry-pipe systems have pressurized air or nitrogen in the pipes and the water is released when the heat of a fire activates the sprinkler head. Deluge systems are used when large amounts of water need to be released quickly, such as when a large area needs to be flooded quickly.
In order to install a wet-pipe system, the pipes must be connected to a water source and the sprinkler heads must be placed at the correct height in the room. Once the system is installed, it must be tested regularly to make sure that it is functioning properly. It is also important to remember that water damage can be caused by a malfunctioning system, so it is important to regularly check and maintain the system.
for more such questions on fire sprinkler system.
https://brainly.com/question/7652753
#SPJ11
how to find the input ac current average and peak values of a three phase full wave bridge rectifier
To find the input AC current average and peak values of a three-phase full-wave bridge rectifier, you need to consider the rectified output waveform and then use the appropriate equations to calculate the values.
To find the input AC current average and peak values of a three-phase full-wave bridge rectifier, you can follow these steps:
Determine the RMS value of the input AC voltage. This can be calculated as Vrms = Vpeak / sqrt(2), where Vpeak is the peak voltage of the AC source.
Calculate the line current of each phase by dividing the RMS voltage by the load resistance. This can be expressed as Iline = Vrms / Rload.
Since the full-wave bridge rectifier is a three-phase rectifier, there will be three line currents. Calculate the total input current by summing the three line currents.
The average input current can be calculated as the RMS value of the total input current. This can be expressed as Iavg = Itotal / sqrt(2).
The peak input current can be calculated as the product of the RMS value and the square root of 2, which can be expressed as Ipeak = Iavg x sqrt(2).
Learn more about three-phase wave rectifier:
https://brainly.com/question/15130306
#SPJ11
A farmers drainage ditch has a width of 2 m and a depth of 50 cm. It is lined with concrete with a roughness of 0.011 and slopes at 0.0009. Calculate the ditch's discharge rate.
Answer:
Using the Manning's Equation, the discharge rate can be calculated as follows:
Q = (1.49/n) x A x R^(2/3) x S^(1/2)
Where:
Q = discharge rate (m^3/sec)
n = Manning's roughness coefficient (0.011)
A = cross sectional area of the ditch (2m x 0.5m = 1 m^2)
R = hydraulic radius (half the width of the ditch, or 1 m)
S = slope of the ditch (0.0009)
Q = (1.49/0.011) x 1m^2 x 1m^(2/3) x 0.0009^(1/2)
Q = 13,636.36 m^3/sec
A 40 HP motor with a load factor of 75% and an efficiency of 89.3% will be replaced with a 30 HP motor with a load factor of 100% and an efficiency of 93.6%. How many kW of power savings will be obtained from this project?
First, we need to calculate the actual power consumption of the 40 HP motor with a load factor of 75% and an efficiency of 89.3%.
Actual power consumption = Rated power x Load factor / Efficiency
= 40 HP x 0.75 / 0.893
= 33.6 kW
Next, we need to calculate the actual power consumption of the 30 HP motor with a load factor of 100% and an efficiency of 93.6%.
Actual power consumption = Rated power x Load factor / Efficiency
= 30 HP x 1 / 0.936
= 31.9 kW
The power savings from this project can be calculated as the difference between the actual power consumption of the 40 HP motor and the actual power consumption of the 30 HP motor.
Power savings = Actual power consumption of 40 HP motor - Actual power consumption of 30 HP motor
= 33.6 kW - 31.9 kW
= 1.7 kW
Therefore, the project will result in a power savings of 1.7 kW.
the process of breaking the wbs into smaller and smaller deliverables is called: group of answer choices functional design detailed specifications value engineering decomposition
Decomposition is the process of breaking the Work Breakdown Structure (WBS) into smaller and smaller deliverables. This process is also sometimes referred to as value engineering or detailed specifications. By decomposing the WBS into smaller pieces, it becomes easier to assign tasks, assign costs, and plan out timelines.
The decomposition process begins by taking the major deliverables of the project and breaking them down into smaller tasks. From there, each task is further broken down into even more specific tasks. This process is repeated until all tasks have been broken down into their smallest components.
The purpose of decomposition is to create a well-defined scope of the project so that it can be managed in an efficient manner. It allows managers to easily identify the resources, cost, and timeline of each task, as well as provide a way to evaluate the progress of each task. It also allows for better control of the overall project.
Decomposition is a critical part of the project management process, as it ensures the project is organized and defined. This ultimately leads to an overall better result for the customer.
You can learn more about Decomposition at: brainly.com/question/8009068
#SPJ11
24. When using grout to fill in the gap between the
concrete and the base plate, be sure to not
Make sure not to overfill the space when using grout to close the gap between the base plate and the concrete because too much grout can eventually put stress on the concrete foundation and cause harm.
Why are foundation plates equipped with grout holes?Additionally, the grout hole will stop air pockets from developing beneath the base plate. If dry pack grout is used or the base plate is less than 600 mm long, such a hole is not deemed essential. When welding the column to the base plate, fillet welds are favoured to butt welds.
What is the bare minimal grout space?Many stone and tile makers advise grout joints to be between 1/8" and 3/16" in size.
To know more about stress visit:
https://brainly.com/question/13261407
#SPJ9
a metal tension specimen of initial diameter 0.505 inches fractures at a load of 5,000 lb with a fracture diameter of 0.325 inches. calculate the true stress at fracture
The true stress at fracture is 59,824.28 psi. True stress at fracture can be calculated by first calculating the true strain at fracture. After calculating the true strain at fracture, calculate the true stress using the given value of force at fracture and the cross-sectional area at fracture. Given data:
Diameter of tension specimen = 0.505 inches
Initial diameter of tension specimen = 0.505 inches
Fracture diameter of tension specimen = 0.325 inches
Load at fracture = 5000 lbs
Formula for true strain calculation:
True strain at fracture = ln (initial diameter / fracture diameter)
Formula for true stress calculation:
True stress at fracture = Force at fracture / Area at fracture
Calculation of true strain:
True strain at fracture = ln (initial diameter / fracture diameter)
= ln (0.505/0.325)= 0.4458
Calculation of area at fracture:
The area of the tension specimen is given by the following formula:
Area = π (diameter)2/4
The area at fracture can be calculated using the fracture diameter.
Area at fracture = π (0.325)2/4= 0.08353 sq inches
Calculation of true stress:
True stress at fracture = Force at fracture / Area at fracture
= 5000 / 0.08353= 59,824.28 psi
Therefore, the answer is 59,824.28 psi.
Learn more about true stress : https://brainly.com/question/13260444
#SPJ11
for a steel alloy it has been determined that a carburizing heat treatment of 10-h duration will raise the carbon concentration to 0.45 wt% at a point 2.5 mm from the surface. estimate the time necessary to achieve
That reaching the desired carbon concentration at a depth of 2.5 mm may take several hours or even days.
To estimate the time necessary to achieve a certain carbon concentration at a specific depth in a steel alloy using a carburizing heat treatment, we need to consider the diffusion of carbon atoms into the material.
The time required for diffusion depends on several factors, including the temperature of the heat treatment, the carbon concentration gradient, and the diffusivity of carbon in the steel alloy. Assuming that the carbon concentration gradient remains constant and that the temperature of the heat treatment remains the same, we can use Fick's Second Law of Diffusion to estimate the time required to achieve a carbon concentration of 0.45 wt% at a depth of 2.5 mm from the surface.
Without knowing the specific alloy or the temperature of the heat treatment, it is difficult to provide a precise estimate. However, we can use typical diffusivity values for carbon in steel alloys and estimate that it may take several hours or even days to achieve the desired carbon concentration at a depth of 2.5 mm.In practice, the exact time required for a carburizing heat treatment will depend on several factors, including the specific alloy, the temperature and duration of the heat treatment, the carbon source, and the desired carbon concentration profile. It is important to carefully control these variables to achieve the desired properties and performance of the material.
To learn more about carburizing refer to:
brainly.com/question/15729955
#SPJ4
what is the purpose of the ground symbol used in electrical circuit diagrams? group of answer choices to show that there is a return path for the current between the source of electrical energy and the load. to show the source of electrical energy for the load. to show that there is common bus for connection of the source of electrical energy to the load.
Answer:
To show that there is a return path for the current between the source of electrical energy and the load.
How many sheets of 4' x 8' pieces of plywood will it take to cover a 24' wall
102 sheets of 4' x eight' pieces of plywood will it take to cover a 24' wall.
locating the quantity of sheets of plywood wanted for a ground, wall, ceiling, or cabinet starts with locating the vicinity that wishes to be covered. vicinity may be located with the aid of multiplying the period and width of the gap in toes. find the rectangular pictures of each space and upload together to locate the whole square photos wanted. Divide by way of the entire square footage by the square footage of a sheet of to discover the range of sheets required to cover the gap. A 4×eight sheet of plywood is 32 ft².
for example, if the place to be blanketed in plywood is 800 ft² then 25 sheets of plywood can be had to cowl it.
800 ÷ 32 = 25 sheets
To know more about plywood click right here
brainly.com/question/30902047
#SPJ4
a 345 kv three-phase line supplies 614 mva at 0.74 pf lagging to a three-phase load which is delta connected. find the magnitude of complex impedance per phase in ohm up to two decimal places. you answered
The magnitude of the complex impedance per phase in ohms is 0.61 ohms (rounded to two decimal places).
To find the complex impedance per phase in ohms, we can use the following formula:
[tex]Z = V^2 / S[/tex]
where:
V = voltage per phase = 345 kV / sqrt(3) = 199.45 kV (assuming a balanced system)
S = apparent power per phase = 614 MVA / 3 = 204.67 MVA (assuming a balanced system)
The real power per phase is given by:
P = S * cos(phi) = 204.67 MW * 0.74 = 151.45 MW
The reactive power per phase is given by:
Q = S * sin(phi) = 204.67 MW * sin(arccos(0.74)) = 113.25 MVAr
The apparent impedance per phase is given by:
|Z| =
[tex]V / \sqrt{3} * \sqrt{(P^2 + Q^2) }/ S \\\\= 199.45 kV / \sqrt{3} * \sqrt{((151.45 MW)^2 + (113.25 MV \ Ar)^2)} / 204.67 MVA[/tex]
|Z| = 0.609 ohms (rounded to two decimal places)
For more question on magnitude click on
https://brainly.com/question/30216692
#SPJ11
the process of heating a metal after cold working relieves internal stress and decreases dislocation density is known as: g
The process of heating a metal after cold working to relieve internal stress and decrease dislocation density is known as annealing.
Annealing is a heat treatment process used to modify the physical and sometimes chemical properties of a material. It is typically used to induce ductility, soften material, improve machinability, and/or help improve cold working properties.
The annealing process requires a recrystallization temperature within a specified time before the cooling process is carried out. The cooling rate depends on the type of metal being annealed. For example, ferrous metals such as steel are usually cooled to room temperature in still air, while copper, silver, and brass are quenched slowly in air or rapidly cooled with water.
Learn more about annealing : https://brainly.com/question/18097221
#SPJ11
what is the purpose of a cnc machining center? machining centers enable a single machine to tolinmg u
CNC machining equipment allows companies to manufacture complex parts with a user-friendly, single-setup machining process. This structure offers significant productivity advantages — cutting labor costs, increasing part quality, and reducing work time.
all of the windings of three phase motors are always wired how?
Three-phase motor windings can be wired in a delta or star configuration. Delta is for high power, star for low. Configuration depends on motor design and operating requirements.
The windings of a three-phase motor can be wired in either a delta or star (also called wye) configuration.
In a delta connection, the windings are connected in a triangle, with each end of a winding connected to the start of the next winding. This type of connection is commonly used for high voltage and high current applications, as it can handle higher power levels than a star connection.
In a star connection, the windings are connected in a Y shape, with one end of each winding connected to a common point called the neutral or star point, and the other ends of the windings connected to the three-phase power supply. This type of connection is typically used for low voltage and low current applications, as it is easier to connect and provides a neutral point for grounding.
The specific configuration used depends on the motor's design, operating requirements, and the power supply available.
To learn more about Three-phase motor windings:
https://brainly.com/question/26236885
#SPJ11
what is the best additive to use to try to minimize the whinning noise in a 1956 chevy powerglide transmission?
The best additive to use to try to minimize the whining noise in a 1956 Chevy Powerglide transmission is Automatic Transmission Additive.
There are many reasons why Automatic Transmission Additive is the best additive to use to try to minimize the whining noise in a 1956 Chevy Powerglide transmission, including but not limited to:ATFs (automatic transmission fluids) are low viscosity lubricants that are formulated to protect automatic transmissions and provide smooth shifting. ATFs, however, have a variety of drawbacks. For example, they can foam, oxidize, shear, and run too hot, all of which can contribute to transmission noise, slipping, and poor shifting.Automatic transmission additives, on the other hand, have been designed to overcome these limitations by incorporating special friction modifiers, anti-wear agents, and seal conditioners, among other ingredients. These additives can reduce friction and wear in the transmission, which can help to quiet down noise and reduce vibration.
Learn more about Automatic Transmission Additive: https://brainly.com/question/14646065
#SPJ11
Which of the following function declaration is correct for a function that takes a 2D array of ints and returns in int?
int f (int a[][3], int rowSize);
int f (int a[3][], int rowSize);
int f (int a[][], int rowSize, intcolumnSize);
The correct function declaration for a function that takes a 2D array of ints and returns an int is:
int f (int a[][3], int rowSize);
1. The return type is "int", which means the function will return an integer value.
2. The function name is "f".
3. The function takes two parameters: a 2D array of ints (int a[][3]) and an integer value (int rowSize).
4. In the 2D array declaration (int a[][3]), the column size is fixed at 3, while the row size is left unspecified. This allows the function to work with arrays of varying row sizes. The int rowSize parameter provides the actual row size.
To learn more about 2D Array declaration : https://brainly.com/question/29846000
#SPJ11