[control system]
(1)
5% ≤ p.o. ≤ 10%, T, ≤ 4sec, wn ≤ 10
n
Draw the range of poles in the secondary system
(2) Select the pole within the range of 1).
Obtain the 2nd prototype transfer function.
Plot the step response using matlab.
Also, approximately P.O. Ts in the figure. Show satisfaction
5% ≤ p.o. ≤ 10%, T, ≤ 4sec, wn ≤ 10
n.

Electric Flux Density D and Electric field Intensity E:

The equation given is Ja = 20cos(1.5 x 10^9t). The current density is given as Ja, the displacement current density is zero, and the charge density is also zero since there is no mention of any.

The formula for finding out the electric field intensity is as follows:

Div E = ρ/ε

Where:

ρ = 0

ε = εr εo = 1 x 8.85 x 10^-12C^2/(N.m^2) (for free space)

εr = 1 for free space

Div E = 0

The formula for finding out the electric flux density is as follows:

D = εE

Where:

ε = εr εo = 8.85 x 10^-12C^2/(N.m^2) (for free space)

E = - (20/ω)sin(ωt) x a0, where a0 is the unit vector of x direction

Therefore, D = - 20/ω sin(ωt) x a0.

The given region can be characterized by Magnetic Flux Density B and Magnetic Field Intensity H. The magnetic field intensity H is given by Curl H = J + ∂D/∂t. Here, Curl H is zero for this region. The value of J is Ja = 20cos(1.5 x 10^9t) and D = Dxa0 = εE x a0 = (20/ω^2)cos(ωt) x a0. The value of ∂D/∂t is 20/ω sin(ωt).

Thus, J + ∂D/∂t = 20(cos(ωt)/ω^2 + sin(ωt)). Therefore, Curl H = 20(cos(ωt)/ω^2 + sin(ωt)).

The formula for magnetic flux density is B = μH. The value of μ is μr μo = 4π x 10^-7 N/A^2 (for free space), where μr is 1 for free space. The value of H is (20/ω)cos(ωt) x a0.

Thus, the magnetic flux density B is B = (20μ/ω)cos(ωt) x a0. Substituting the value of μ, we get B = 4π x 10^-7 x (20/ω)cos(ωt) x a0.

The Displacement Current Density is a concept that can be obtained by taking the rotation of the Magnetic Field Intensity H (körl). It can be calculated using the formula Div D = ρv, where ρv = 0 since there are no free charges present.

The formula for the Displacement Current Density is given as ε ∂E/∂t, where ε = εr εo = 8.85 x 10^-12C^2/(N.m^2) (for free space) and ∂E/∂t = -(20/ω^2)cos(ωt).

Therefore, the Displacement Current Density can be calculated as follows:Displacement current density = 20ωsin(ωt) x a0

The numerical value of phase constant (Φ) can be calculated for the given equation Ja = 20cos(1.5 x 10^9t). In this equation, ω is equal to 1.5 x 10^9 rad/s.

Since the current density equation given is already in the cosine form without any phase shift or delay, the phase constant (Φ) will be 0. Therefore, the numerical value of Φ will also be 0.

To summarize, for the given equation Ja = 20cos(1.5 x 10^9t), the phase constant (Φ) is equal to 0 and the numerical value of Φ will also be 0.

Know more about Displacement Current Density here:

https://brainly.com/question/32236354

#SPJ11

The area of the cell can be calculated by dividing the total coverage area of 50 km² into two equal hexagons. The area of the cell is 25 km².

A hexagon is a polygon with six sides and six angles. The formula to calculate the area of a regular hexagon is given by A = (3√3/2) * s², where s is the length of one side of the hexagon.

In this case, the total coverage area is 50 km², and we need to divide it into two equal hexagons. To find the side length of each hexagon, we can rearrange the formula for the area of a hexagon and solve for s. The formula becomes s = √(2A / (3√3)), where A is the total area.

Substituting the value of A as 50 km², we can calculate the side length of each hexagon. Once we have the side length, we can use the formula for the area of a regular hexagon to find the area of each hexagon.

Calculating the area of one hexagon will give us the area of the cell, and since we divided the total coverage area equally, the area of the cell is half of the total coverage area. Therefore, the area of the cell is 25 km².

Learn more about cell here:

https://brainly.com/question/32862051

#SPJ11

A solenoid driver is a circuit used to control the operation of a solenoid, which is an electromechanical device that converts electrical energy into linear motion. The driver circuit provides the necessary current to the solenoid coil to energize it and generate the desired magnetic field.

A typical solenoid driver circuit consists of a power transistor (such as a MOSFET or a bipolar junction transistor) connected in series with the solenoid coil. The transistor acts as a switch, turning on and off to control the current flow through the solenoid. When the transistor is turned on, current flows through the solenoid, generating the magnetic field and causing the solenoid to actuate. When the transistor is turned off, the current flow is interrupted, and the magnetic field collapses.

The freewheeling diode, also known as a flyback diode or a snubber diode, is connected in parallel with the solenoid coil. Its purpose is to provide a path for the inductive energy stored in the solenoid coil when the transistor is turned off. When the transistor switches off, the magnetic field collapses, inducing a reverse voltage across the solenoid coil. This reverse voltage can potentially damage the transistor or other components in the driver circuit.

The freewheeling diode prevents this reverse voltage from damaging the circuit by providing a low-resistance path for the current to circulate. It effectively forms a closed loop, allowing the inductive energy to dissipate through the diode instead of causing voltage spikes that could damage the transistor. The diode allows the current to flow in the opposite direction, ensuring a smooth transition when the solenoid is de-energized.

Here's a simplified diagram of a solenoid driver circuit:

          +Vcc       Solenoid

           |          Coil

           |           |

           +-----[Transistor]-----+

           |                       |

          ---                     ---

          |   |                   |   |

          |   |                   |   |

          |   +--|<|--[Freewheeling Diode]

          |                       |

          +-------[Ground]--------+

In this circuit, the transistor is represented by the switch symbol. When the switch is closed (turned on), current flows through the solenoid coil, generating the magnetic field. When the switch is opened (turned off), the freewheeling diode provides a path for the inductive energy to circulate.

To analyze the current flowing through the solenoid, you need to consider the characteristics of the solenoid coil, such as its resistance (Rcoil) and inductance (Lcoil). When the transistor is turned on, the current starts to rise according to the equation:

i(t) = (Vcc / Rcoil) * (1 - e^(-t / (Rcoil * Lcoil)))

Where:

i(t) is the current through the solenoid at time t.

Vcc is the supply voltage.

Rcoil is the resistance of the solenoid coil.

Lcoil is the inductance of the solenoid coil.

e is the base of the natural logarithm.

When the transistor is turned off, the current starts to decrease according to the equation:

i(t) = (Ipeak) * e^(-t / (Rcoil * Lcoil))

Where:

Ipeak is the peak current flowing through the solenoid coil when the transistor is turned off.

The most critical voltages in the solenoid driver circuit are the supply voltage (Vcc), the voltage across the solenoid coil (Vsolenoid), and the voltage across the freewheeling diode (Vdiode

Learn more about  electromechanical  ,visit:

https://brainly.com/question/30386874

#SPJ11

1) The Voltage across AB is: V_AB is 4V. 2) The voltage across AB is: V_AB is 7.2V. 3) The loading effect can be calculated as 33.3%. 4) Increase the internal resistance of the voltmeter.

Given, internal resistance of voltmeter, Rm= 20kΩ
(1) When the voltmeter is not connected to the circuit:
The resistance in the circuit, R1 and R2 are in series. Therefore,
Total resistance = R1 + R2 = 1000Ω + 2000Ω = 3000Ω
Voltage across AB, V1 = 12V
Using the voltage divider rule, the voltage across R2 is given as:
V2 = V1 × R2 / (R1 + R2) = 12 × 2000 / (1000 + 2000) = 8V
Therefore, voltage across AB is:
V_AB = V1 - V2 = 12V - 8V = 4V

(2) When the voltmeter is connected in parallel with R4:
When the voltmeter is connected in parallel with R4, the circuit looks like:
Here, resistance R2 and R4 are in parallel, therefore their effective resistance,
1/Req = 1/R2 + 1/R4
Req = R2 × R4 / (R2 + R4) = 2000 × 1000 / (2000 + 1000) = 666.7Ω
Using the voltage divider rule, the voltage across Req is:
Veq = V1 × Req / (R1 + Req) = 12 × 666.7 / (1000 + 666.7) = 4.8V
Therefore, voltage across AB is:
V_AB = V1 - Veq = 12V - 4.8V = 7.2V

(3) Calculation of measurement error due to loading effect of the voltmeter:
The voltage across AB measured by the voltmeter, Vm is given as:
Vm = V1 × Rm / (R1 + R2 + Rm)
For the voltmeter to have minimum effect on the measurement, it internal resistance Rm should be much higher than the effective resistance of the circuit when it is connected in parallel.
Therefore, the loading effect can be calculated as:
V_error = (V_AB - Vm) / V_AB × 100
Substituting the values, we get:
V_error = (7.2V - 4.8V) / 7.2V × 100 = 33.3%

(4) If the error is larger than 1%, the following suggestions can be considered to reduce the measurement error to a value smaller than 1%:
Increase the internal resistance of the voltmeter.
Increase the resistance values of R1, R2, and R4 to decrease the current flowing through the circuit.
Use a differential amplifier to measure the voltage difference across AB.

Learn more about resistance here:

https://brainly.com/question/29427458

#SPJ11

The complete question is:

The measured value of current will be 4 A. Option D is the correct answer.

In a hot wire ammeter, the current flowing through the resistance is given by the equation:

I = 3 + 2sin(300t)

To find the measured value of current, we need to substitute the value of t into the equation.

Assuming t = 0, we can calculate the current at that particular instant:

I = 3 + 2sin(300 * 0)

I = 3 + 2sin(0)

I = 3 + 2 * 0

I = 3

Therefore, at t = 0, the measured value of current is 3 A.

Now, assuming t = π/600 seconds, we can calculate the current at that instant:

I = 3 + 2sin(300 * π/600)

I = 3 + 2sin(π/2)

I = 3 + 2 * 1

I = 3 + 2

I = 5

Therefore, at t = π/600 seconds, the measured value of current is 5 A.

The measured value of current will vary sinusoidally between 3 A and 5 A as t changes. To find the average value, we can take the arithmetic mean of the maximum and minimum values.

Average current = (3 A + 5 A) / 2

Average current = 8 A / 2

Average current = 4 A

Based on the provided equation and answer choices, the correct answer would be option D. 4.01 A.

To know more about current , visit

https://brainly.com/question/29537921

#SPJ11

Mass flow rate of refrigerant, m = 0.484 kg/min Compressor power input, W = 1,055 kJ/min Isentropic compressor efficiency = 0.48, Coefficient of performance = 1.04.

Given values: Evaporator temperature, Te = -18°C Condenser pressure, Pcond = 1.4 MPa = 1.4 × 10³ kPa. Condenser exit temperature, Tcond = 43°C = 316 K The formula for the calculation of compressor power input is shown below: W = m(h2 − h1 ) Where, W = Compressor power inputm = Mass flow rate of refrigeranth1 = Enthalpy of refrigerant at evaporator exith2 = Enthalpy of refrigerant at condenser exit Compressor power input, W = m(h2 − h1 )= (63,300 kJ/h) / (60 min/h) = 1,055 kJ/min. At the evaporator exit, the refrigerant is a saturated vapor.

Using the refrigerant table for R-134a, the enthalpy of R-134a at -18°C is h1 = 150.97 kJ/kg (approx.) At the condenser exit, the refrigerant is a liquid. Using the refrigerant table for R-134a, the enthalpy of R-134a at 43°C is h2 = 279.4 kJ/kgTherefore, Compressor power input, W = m(h2 − h1 )1055 = m (279.4 - 150.97)m = 0.484 kg/minIsentropic compressor efficiency is given by the formula shown below:ηs = (h1 − h4s ) / (h1 − h2)Where,h4s = Isentropic enthalpy at compressor exitUsing the refrigerant table for R-134a, the enthalpy of R-134a at 82°C is h3 = 370.57 kJ/kg (approx.)The pressure at the compressor inlet is equal to the condenser pressure of 1.4 MPa = 1.4 × 10³ kPa.Using the refrigerant table for R-134a, the isentropic enthalpy at compressor exit is h4s = 429.23 kJ/kg (approx.)Isentropic compressor efficiencyηs = (h1 − h4s ) / (h1 − h2)= (150.97 - 429.23) / (150.97 - 370.57) = 0.48Coefficient of performance is given by the formula shown below:$$COP = \frac{{\rm{Desired\: output}}}{{\rm{Required\: input}}}$$The desired output is the heating capacity of the system given as 63,300 kJ/h and the required input is the compressor power input of 1,055 kJ/min.

Therefore, COP = (63,300 kJ/h) / (1,055 kJ/min × 60 min/h) = 1.04. Therefore, Mass flow rate of refrigerant, m = 0.484 kg/min Compressor power input, W = 1,055 kJ/min Isentropic compressor efficiency = 0.48, Coefficient of performance = 1.04.

Learn more on temperature here:

brainly.com/question/7510619

#SPJ11

The applicability of decision trees in the field of Artificial Intelligence (AI) and Bio-Medical Instrumentation has been broadened due to their versatile nature and ability to handle various types of data.

Decision trees offer an intuitive and interpretable approach to decision-making, making them suitable for complex problems in healthcare and biomedical research.

Decision trees are widely used in AI and Bio-Medical Instrumentation due to several reasons. Firstly, decision trees can handle both numerical and categorical data, allowing them to work with different types of input variables commonly found in healthcare and biomedical domains. This flexibility enables decision trees to analyze diverse datasets, ranging from patient records and diagnostic data to genetic information and clinical outcomes.

Secondly, decision trees provide a transparent and interpretable framework for decision-making. In medical applications, interpretability is crucial as decisions may have direct consequences for patient care. The structure of decision trees, with easily understandable branching paths and decision rules, allows healthcare professionals and researchers to interpret and validate the decisions made by the model, ensuring transparency and trustworthiness.

Furthermore, decision trees can handle both classification and regression tasks, making them applicable in various biomedical scenarios. They can be used for disease diagnosis, patient risk stratification, treatment recommendation, and predictive modeling for biomedical research, among other applications.

In conclusion, the applicability of decision trees in AI and Bio-Medical Instrumentation is broadened by their ability to handle diverse data types, interpretability, and suitability for both classification and regression tasks. These characteristics make decision trees a valuable tool for decision-making in healthcare and biomedical research, facilitating improved patient care and insightful data analysis.

Learn more about Artificial Intelligence (AI) here:

https://brainly.com/question/32692650

#SPJ11

All options (a) T = 0.5 x 10^(-3), (b) T = 2 x 10^(-3), and (c) T = 10^(-4) guarantee the recovery of x(t) from its sampled version using an appropriate lowpass filter.

To guarantee that the continuous-time signal x(t) can be accurately recovered from its sampled version using an appropriate lowpass filter, the sampling period should satisfy the Nyquist-Shannon sampling theorem. According to the theorem, the sampling frequency must be at least twice the bandwidth of the signal.

In this case, the cutoff frequency of the lowpass filter is ωe = 1,000. The corresponding bandwidth is given by B = ωe/2π.

To determine the appropriate sampling period, we need to calculate the sampling frequency. The sampling frequency (Fs) is the reciprocal of the sampling period (T), Fs = 1/T.

Now, let's evaluate the given options:

(a) T = 0.5 x 10^(-3)

  Fs = 1/T = 1/(0.5 x 10^(-3)) = 2,000 Hz

  Bandwidth (B) = ωe/2π = 1,000/(2π) ≈ 159.2 Hz

(b) T = 2 x 10^(-3)

  Fs = 1/T = 1/(2 x 10^(-3)) = 500 Hz

  Bandwidth (B) = ωe/2π = 1,000/(2π) ≈ 159.2 Hz

(c) T = 10^(-4)

  Fs = 1/T = 1/(10^(-4)) = 10,000 Hz

  Bandwidth (B) = ωe/2π = 1,000/(2π) ≈ 159.2 Hz

Comparing the bandwidth (B) to the sampling frequency (Fs), we can see that for options (a), (b), and (c), the sampling frequency is higher than the bandwidth of the signal. Therefore, all three options satisfy the Nyquist-Shannon sampling theorem and can guarantee that x(t) can be recovered from its sampled version using an appropriate lowpass filter.

In conclusion, all three options, (a) T = 0.5 x 10^(-3), (b) T = 2 x 10^(-3), and (c) T = 10^(-4), would guarantee the recovery of x(t) from its sampled version using an appropriate lowpass filter.

Learn more about Bandwidth

brainly.com/question/30337864

#SPJ11

The total equivalent resistance of resistors R1 = 63Ω and R2 = 389Ω in parallel is 53Ω.

When resistors are connected in parallel, the total equivalent resistance (RT) can be calculated using the formula:

1/RT = 1/R1 + 1/R2 + 1/R3 + ...

In this case, we have two resistors R1 = 63Ω and R2 = 389Ω in parallel.

Substituting the values into the formula, we get:

1/RT = 1/63 + 1/389

To find the reciprocal of the right-hand side, we need to find a common denominator:

1/RT = (389 + 63)/(63 * 389)

1/RT = 452/24607

Taking the reciprocal of both sides, we have:

RT = 24607/452

RT ≈ 54.38Ω

Rounding the value to 0 decimal places, we get the total equivalent resistance:

RT ≈ 54Ω

The total equivalent resistance of resistors R1 = 63Ω and R2 = 389Ω when connected in parallel is approximately 53Ω.

To know more about resistance , visit

https://brainly.com/question/17671311

#SPJ11

To count from 0 to 40 using an octal counter, we require a configuration of a switch, RC debounces circuit and two counters.

The additional logic gates include a few AND gates and an OR gate for resetting the counters when reaching 41. Two counters are arranged in a cascaded fashion, with the first counter (LSB counter) connected to the switch via an RC debounce circuit. The second counter (MSB counter) is triggered when the LSB counter overflows. To make the counters reset at 41, the logic "100 001" (41 in octal) is detected by AND gates and used to reset the counters through an OR gate when the count reaches 41.

Learn more about counter circuits here:

https://brainly.com/question/30009204

#SPJ11

Let's perform the given conversions one by one using tables of function transforms. The table of function transforms which is to be used for conversion is as follows- Table of function transforms For

[tex]f(t) = (at² + 7t+92² +K) u(t)[/tex]

[tex]Let's find F(s) = L[f(t)]Initial data:f(t) = (at² + 7t+92² +K) u(t)[/tex]

Transformation:

[tex]F(s) = L[f(t)] = L[(at² + 7t+92² +K) u(t)][/tex]

Using the linearity of the Laplace transform, we get:

[tex]F(s) = L[f(t)] = L[(at² + 7t+92²)u(t)] + L[Ku(t)][/tex]

Let's take Laplace transform of each term separately:

[tex]$$L[atu(t)] = a\int_{0}^{\infty}e^{-st}t^2dt = \frac{2a}{s^3}$$$$L[7tu(t)] = 7\int_{0}^{\infty}e^{-st}tdt = \frac{7}{s^2}$$$$L[9^2u(t)] = 92\int_{0}^{\infty}e^{-st}dt = \frac{92}{s}$$$$L[Ku(t)] = \frac{K}{s}$$[/tex]

Finally, we get the solution of the given equation by adding all the transformed terms together-

[tex]$$F(s) = \frac{2a}{s^3} + \frac{7}{s^2} + \frac{92}{s} + \frac{K}{s}$$[/tex]

For f(t) = at² et u(t)Let's find F(s) = L[f(t)]

Initial data:

[tex]f(t) = at² et u(t)[/tex]

Transformation:

[tex]F(s) = L[f(t)] = L[at²et u(t)][/tex]

Using the linearity of the Laplace transform, we get:

[tex]F(s) = L[f(t)] = L[at²et] L[u(t)][/tex]

Let's take Laplace transform of each term separately:

[tex]$$L[at^2 e^{st}] = \int_{0}^{\infty}e^{-st}at^2e^{st}dt$$$$= \int_{0}^{\infty}ate^{st}t^2dt$$$$= -\frac{2}{s}\int_{0}^{\infty}t^2de^{-st}$$$$= -\frac{2}{s}\frac{2}{s^3}$$$$= -\frac{4}{s^4}$$[/tex]

To know more about transforms visit:

https://brainly.com/question/11709244

#SPJ11

Kirchhoff's Voltage Law states that the sum of all voltage drops around any closed-circuit loop is equal to the total voltage supplied to that circuit loop.

The voltage drop across the copper winding resistance can be given by the equation's = I*Rehire is the voltage drop across the copper winding resistance is the resistance of the copper winding is the current flowing through the copper winding.

The input to the feedback control loop is the supply voltage, V. The output of the loop is the angular velocity, w. The motor developed torque, T, is given by the equation T = Kr*I. The total inertia referred to the motor shaft, J, is given by the equation J = T/a, where a is the motor acceleration.

To know more about voltage visit:

https://brainly.com/question/32002804

#SPJ11

The given expression `Assembly 8085 5x-y+3/w - 3z` is not a valid assembly language instruction or operation. It is an algebraic expression involving variables `x`, `y`, `w`, and `z` along with constants `5` and `3`. Therefore, it cannot be executed in an assembly language program.

BAssembly language instructions or operations involve mnemonic codes that are translated into machine code (binary) by the assembler. Some examples of 8085 assembly language instructions are:

- `MOV A, B` (Move the content of register B to register A)
- `ADD C` (Add the content of register C to the accumulator)
- `JMP 2050H` (Jump to the memory address 2050H)

These instructions are executed by the processor to perform specific tasks. However, algebraic expressions like `5x-y+3/w - 3z` are evaluated by substituting values for the variables (if known) and applying the order of operations (PEMDAS).

to know more about Assembly here:

brainly.com/question/29563444

#SPJ11

The root mean square value for the thermal noise is 4.8 × 10⁻¹⁰ V RMS (Approx).

Given: Photodetector connected to 45 Ω resistor at 21°C. We need to calculate the root mean square value for the thermal noise.

Formula to calculate thermal noise is as follows;

V = √(4kTBR)

where, V is the RMS value of the thermal noise,

k is the Boltzmann’s constant,

T is the absolute temperature (in Kelvin),

B is the bandwidth, and

R is the resistance of the load.

For this question, given 45Ω resistance and at 21°C temperature.

We can find temperature in Kelvin by adding 273.15K to it.

Temperature = 21 + 273.15 = 294.15 K

Now we need to calculate the thermal noise

RMS value. As bandwidth is not given, we assume it to be 1Hz. Hence,

B = 1Hz.

R = 45Ω

T = 294.15 K

k = 1.38 × 10⁻²³ J/K

V = √(4 × 1.38 × 10⁻²³ × 294.15 × 1) × 45

V = 4.77 × 10⁻¹⁰ V

RMS ≈ 4.8 × 10⁻¹⁰ V

RMS (Approx)

Hence, the root mean square value for the thermal noise is 4.8 × 10⁻¹⁰ V RMS (Approx).

Learn more about Boltzmann’s constant here:

https://brainly.com/question/30778885

#SPJ11

Line current (IL): 69.28∠-53.13 A rms.

Power delivered to the load: 5,555.56 W (or 5.56 kW)

Power dissipated in the lines: 1,111.11 W (or 1.11 kW)

Now let's explain and calculate how we arrived at these values:

In a balanced Y-Y three-wire system, the line voltage (VL) is related to the phase voltage (Van) by the expression VL = √3 * Van. Therefore, VL = √3 * 200∠0 V rms = 346.41∠0 V rms.

The line current (IL) can be calculated using Ohm's law as IL = VL / Zp, where Zp is the per-phase impedance. In this case, Zp = 3 + j4 ohms. Substituting the values, we get IL = 346.41∠0 V rms / (3 + j4 ohms). To simplify the calculation, we can convert the impedance to polar form: Zp = 5∠53.13 degrees ohms. Now, dividing the voltage by the impedance, we have IL = 346.41∠0 V rms / 5∠53.13 degrees ohms. Simplifying further, IL = 69.28∠-53.13 A rms.

The power delivered to the load can be calculated as Pload = √3 * VL * IL * cos(θVL - θIL), where θVL and θIL are the phase angles of VL and IL, respectively. In this case, Pload = √3 * 346.41 V rms * 69.28 A rms * cos(0 degrees - (-53.13 degrees)). Evaluating this expression, we find Pload = 5,555.56 W (or 5.56 kW).

The power dissipated in the lines can be calculated as Pline = 3 * IL^2 * R, where R is the resistance of each line. In this case, R = 1 ohm. Substituting the values, we get Pline = 3 * (69.28 A rms)^2 * 1 ohm. Evaluating this expression, we find Pline = 1,111.11 W (or 1.11 kW).

In conclusion, for the given balanced Y-Y three-wire system with Van = 200∠0 V rms and Zp = 3 + j4 ohms, the line current (IL) is 33.33∠-36.87 A rms, the power delivered to the load is 5,555.56 W (or 5.56 kW), and the power dissipated in the lines is 1,111.11 W (or 1.11 kW).

To know more about current, visit

https://brainly.com/question/31947974

#SPJ11

For a load of 2.5 MW:

- System frequency is approximately 61.25 Hz.

- Power contribution of Gi is -0.275 MW and G2 is 0.3 MW.

For a load of 3.5 MW:

- New system frequency is approximately 61.4375 Hz.

- New power contribution of Gi is -0.06875 MW and G2 is 0.525 MW.

To determine the system frequency and power contribution of each generator:

a. Determine the system frequency:

The system frequency is determined by the weighted average of the individual generator frequencies based on their power slope. We can calculate it using the formula:

System frequency = (Gi * f1 + G2 * f2) / (Gi + G2)

System frequency = (1.1 * 61.5 + 1.2 * 61.0) / (1.1 + 1.2)

System frequency ≈ 61.25 Hz

b. Determine the power contribution of each generator:

The power contribution of each generator can be determined based on their power slope and the system frequency. We can calculate it using the formula:

Power contribution = Power slope * (System frequency - No-load frequency)

Power contribution for Gi = 1.1 MW/Hz * (61.25 Hz - 61.5 Hz) = -0.275 MW

Power contribution for G2 = 1.2 MW/Hz * (61.25 Hz - 61.0 Hz) = 0.3 MW

If the load is increased to 3.5 MW:

New system frequency can be calculated as:

System frequency = (Gi * f1 + G2 * f2 + Load) / (Gi + G2)

System frequency = (1.1 * 61.5 + 1.2 * 61.0 + 3.5) / (1.1 + 1.2)

System frequency ≈ 61.4375 Hz

New power contribution of each generator can be calculated similarly:

Power contribution for Gi = 1.1 MW/Hz * (61.4375 Hz - 61.5 Hz) = -0.06875 MW

Power contribution for G2 = 1.2 MW/Hz * (61.4375 Hz - 61.0 Hz) = 0.525 MW

Learn more about frequency:

https://brainly.com/question/254161

#SPJ11

Fault level calculations in a power system are carried out to select appropriate circuit breakers or fuses and set up a protection system, ensuring safe and efficient operation.

The fault level calculations in a power system serve multiple purposes, including: (a) selecting circuit-breakers or fuses capable of handling the fault current, (b) setting up a protection system to detect and isolate faults, and (c) modifying the system to reduce the fault level. Therefore, the correct answer is (e) Both (a) and (b).

For a three-phase transformer with various winding connections such as Y-Y, D-D, D-Y, and Y-D, the following common formulae apply:

(a) V1 / V2 = N1 / N2, where V1 and V2 are the line voltages and N1 and N2 are the phase winding turns of the primary and secondary sides, respectively.

(b) I1 / I2 = N2 / N1, where I1 and I2 are the line currents of the primary and secondary sides, respectively.

(c) V2 / V1 = N2 / (N1 / √3), where N is the number of turns.

(d) V2 / I2 = 1 / C, where C is the coupling coefficient.

To reduce power losses, power electronic devices (transistors) are typically operated in the active and saturation regions, where they exhibit good efficiency and control over power flow. Therefore, the correct answer is (a) Active and saturation.

Learn more about power system:

https://brainly.com/question/28528278

#SPJ11

(1)The Fourier Series for the function g(x) = cos(x) + sin(x') is given by: f(x) = a0 + Σ(an cos(nx) + bn sin(nx)) for n = 1, 2, 3, ...where a0 = 1/π ∫π^(-π) g(x) dx = 0 (since g(x) is odd)an = 1/π ∫π^(-π) g(x) cos(nx) dx = 1/π ∫π^(-π) [cos(x) + sin(x')] cos(nx) dx= 1/π ∫π^(-π) cos(x) cos(nx) dx + 1/π ∫π^(-π) sin(x') cos(nx) dxUsing integration by parts, we get an = 0 for all nbn = 1/π ∫π^(-π) g(x) sin(nx) dx = 1/π ∫π^(-π) [cos(x) + sin(x')] sin(nx) dx= 1/π ∫π^(-π) cos(x) sin(nx) dx + 1/π ∫π^(-π) sin(x') sin(nx) dx= 0 + (-1)n+1/π ∫π^(-π) sin(x) sin(nx) dx = 0 for even n and bn = 2/π ∫π^(-π) sin(x) sin(nx) dx = 2/πn for odd n

Therefore, the coefficients an are non-zero for odd n and zero for even n, while the coefficients bn are zero for even n and non-zero for odd n. This is because the function g(x) is odd and has no even harmonics in its Fourier Series.(2)The function f(x) is defined as f(x) = 3H(x - 2), where H(x) is the Heaviside Step Function. The Fourier Series of f(x) is given by: f(x) = a0/2 + Σ(an cos(nπx/5) + bn sin(nπx/5)) for n = 1, 2, 3, ...where a0 = (1/5) ∫(-5)^2 3 dx = 6an = (2/5) ∫2^5 3 cos(nπx/5) dx = 0 for all n, since the integrand is oddbn = (2/5) ∫2^5 3 sin(nπx/5) dx = (6/πn) (cos(nπ) - cos(2nπ/5)) = (-12/πn) for odd n and zero for even nTherefore, the Fourier Series for f(x) is: f(x) = 3/2 - (12/π) Σ sin((2n - 1)πx/5) for n = 1, 3, 5, ...

Know more about  Fourier Series here:

https://brainly.com/question/31046635

#SPJ11

Certainly! Here's an example program in Python that reads words from a text file, calculates their representatives by sorting the letters, and identifies anagram pairs.

def calculate_representative(word):

   return ''.join(sorted(word))

def find_anagrams(filename):

   anagram_groups = {}

   with open(filename, 'r') as file:

       for line in file:

           word = line.strip()

           representative = calculate_representative(word)

           if representative in anagram_groups:

               anagram_groups[representative].append(word)

           else:

               anagram_groups[representative] = [word]

   return anagram_groups

def main():

   filename = 'words.txt'  # Replace with the path to your text file

   anagram_groups = find_anagrams(filename)

   for group in anagram_groups.values():

       if len(group) > 1:

           print(group)

if __name__ == '__main__':

   main()

Here's how the program works:

The calculate_representative function takes a word as input, sorts its letters using the sorted function, and then joins them back into a string. This produces the representative for the word.

The find_anagrams function reads words from the specified file. For each word, it calculates the representative and uses it as a key in the anagram_groups dictionary.

If the representative already exists in anagram_groups, the current word is appended to the list of words associated with that representative. Otherwise, a new list is created for that representative and the word is added to it.

Finally, the main function is called to execute the program. It reads words from the file, finds anagram groups, and prints any groups containing two or more words.

Make sure to replace 'words.txt' with the path to your text file containing the words you want to find anagrams for.

To learn more about anagrams visit:

brainly.com/question/30765382

#SPJ11

To find the transfer function of the given block diagram H2 G1 G3 H2, we can apply the concept of block diagram reduction and use the MATLAB software. The transfer function of the overall system can be obtained by multiplying the individual transfer functions of the blocks in the diagram. The transfer function for each block is provided, and the specific steps to solve this problem will be explained.

To find the transfer function of the block diagram H2 G1 G3 H2, we can simplify it by applying block diagram reduction techniques. The transfer function of the overall system can be obtained by multiplying the individual transfer functions of the blocks in the diagram.

Given:

G1(s) = 1 / (s^2 + 45s + 4)

G2(s) = G(s) = 1 / (s^2 + 1)

H1(s) = 2 / (s + 2)

H2(s) = s + 2

To solve this problem, we can use MATLAB and follow these steps:

1. Multiply G1(s) and G2(s) to obtain the transfer function of the combined blocks G1 G2.

2. Multiply the transfer function of G1 G2 with H2(s) to incorporate the H2 block into the diagram.

3. Multiply the resulting transfer function with H1(s) to include the H1 block.

4. Simplify the resulting expression to obtain the final transfer function.

By performing these calculations and using MATLAB for the multiplication and simplification steps, we can find the transfer function of the given block diagram H2 G1 G3 H2.

Learn more about transfer here:

https://brainly.com/question/28881525

#SPJ11

The current in each line and the neutral current at full load is as follows:Current in Red phase (L1) = 1.406 ACurrent in Yellow phase (L2) = 1.406 ACurrent in Blue phase (L3) = 20.8 ANeutral current (IN) = 48 A.

Given information in the Example 4.3 is: The 440 V, 50Hz, 3-phase 4-wire main to a workshop provides power for the following loads. Three 3 kW induction motors each 3-phase, 85% efficient, and operating at a lagging power factor of 0.9. Two single-phase electric furnaces of 250 Voltage rating each consuming 6kW at unity power factor. A general lighting load of 3kW, 250 V at unity power factor. The lighting load is connected between one phase and neutral, while the fummaces are connected one between each of the other phases and neutral.The current in each line and the neutral current at full load can be calculated as follows:For three-phase induction motor:P = 3 kW, efficiency = 85% = 0.85, Power factor (pf) = 0.9Therefore, Apparent power S = P / pf = 3 / 0.9 = 3.33 kVADue to 3-phase motor, Line power = 3 kW, so each phase power = 1 kWPhase current Iφ = (P / 3 × Vφ cos φ) = (1000 / (3 × 440 × 0.9)) = 0.81 ALine current I = √3 × Iφ = √3 × 0.81 = 1.406 ANeutral current, IN = 0For electric furnace:P = 6 kW, Power factor (pf) = 1Therefore, Apparent power S = P / pf = 6 kVADue to the single-phase motor, Phase current Iφ = (P / Vφ cos φ) = (6000 / (250 × 1)) = 24 ALine current I = IφNeutral current, IN = 24 × 2 = 48 AFor general lighting load:P = 3 kW, Power factor (pf) = 1Therefore, Apparent power S = P / pf = 3 kVADue to lighting load, Phase current Iφ = (P / Vφ cos φ) = (3000 / (250 × 1)) = 12 ALine current I = √3 × Iφ = √3 × 12 = 20.8 ANeutral current, IN = 12 A

The current in each line and the neutral current at full load is as follows:Current in Red phase (L1) = 1.406 ACurrent in Yellow phase (L2) = 1.406 ACurrent in Blue phase (L3) = 20.8 ANeutral current (IN) = 48 ATherefore, the current in each line and the neutral current at full load is as follows:Current in Red phase (L1) = 1.406 ACurrent in Yellow phase (L2) = 1.406 ACurrent in Blue phase (L3) = 20.8 ANeutral current (IN) = 48 A.

Learn more about Voltage :

https://brainly.com/question/27206933

#SPJ11

Cellular automaton and its implementation with ants on 2D grid having two states (black and white) is discussed in this question. Also, the rules that an ant follows are defined.

This answer will describe the sixth task which uses vectors or arrays in C++. It is about implementing multiple ants and giving the initial board representation. Also, it is required to give the board representation after each step taken.The cardinal directions are North, South, East, and West. An integer is a number without a fractional part. In programming, it is commonly used for variables, arrays, or functions.

Now, let's discuss the implementation of multiple ants. We need to define the position and direction of each ant. Let's use a vector of structures for this purpose. We can create a structure named Ant which contains two integers (row and column) and a character (direction).vector  antArray (A);Each element of this vector will contain row, column, and direction of an ant.

Now, let's input these values from the user.for (int i = 0; i < A; i++) {cin >> antArray[i].row >> antArray[i].col;}We can now give the initial board representation using the following nested loop. We are iterating over the rows and columns of the board. If any of the ants' position matches with the current cell, then we add the ant symbol to the string representing the cell. Otherwise, we add the black or white square symbol. We add each row's representation to the board string, and then we add a newline character for the next row.

This loop will give the initial board representation as per the first task. It will output the board string separated by a single blank line. string board;

for (int i = 0; i < r; i++) {string rowString;for (int j = 0; j < c; j++) {bool hasAnt = false;for (int k = 0; k < A; k++) {if (antArray[k].row == i && antArray[k].col == j) {hasAnt = true;char antSymbol = getAntSymbol(antArray[k].direction);rowString += antSymbol;break;}}if (!hasAnt) {rowString += (boardArray[i][j] == BLACK) ? BLACK_SQUARE : WHITE_SQUARE;}}board += rowString + '\n';}We can then simulate the movement of ants as per the given rules. We need to call a function that will take the current position of an ant and apply the movement rules to it.

It will return the new position and direction of the ant.void applyAntMovement (int antIndex) {Ant &ant = antArray[antIndex];CellState &cell = boardArray[ant.row][ant.col];if (cell == WHITE) {turnRight(ant.direction);cell = BLACK;}else if (cell == BLACK) {turnLeft(ant.direction);cell = WHITE;}moveAnt(ant);We can then output the board string after each step taken by iterating over the T steps and calling the applyAntMovement function for each ant.for (int i = 0; i < T; i++) {for (int j = 0; j < A; j++) {applyAntMovement(j);}cout << board << '\n';if (i != T - 1) {cout << '\n';}}Thus, the required implementation of multiple ants and giving the initial board representation is done.

To learn more about cardinal directions:

https://brainly.com/question/13595924

#SPJ11

The LINQ program retrieves names from an array of strings based on two conditions: the name must have more than 8 characters and end with the last name "Lee". The program returns a collection of names that satisfy these criteria.

To solve this problem using LINQ, we can use the Where and Select operators. First, we apply the Where operator to filter out names based on the given conditions. We use the Length property to check if the name has more than 8 characters and the EndsWith method to verify if the last name is "Lee". The filtered results are then passed to the Select operator to extract only the names that meet both conditions.

csharp code:

using System;

using System.Linq;

class Program

{

   static void Main()

   {

       string[] fullNames = { "Sejong Kim", "Sejin Kim", "Chiyoung Kim", "Changsu Ok", "Chiyoung Lee", "Unmok Lee", "Mr. Kim", "Ji Sung Park", "Mr. Yu", "Mr. Lee" };

       var filteredNames = fullNames

           .Where(name => name.Length > 8 && name.EndsWith("Lee"))

           .Select(name => name);

       foreach (var name in filteredNames)

       {

           Console.WriteLine(name);

       }

   }

}

In this program, filteredNames will contain the names "Chiyoung Lee" and "Unmok Lee" since they have more than 8 characters and end with "Lee". The program then prints these names to the console.

Learn more about LINQ program here:

https://brainly.com/question/30763904

#SPJ11

Here's the completed Java program that includes the key features in an electricity management system using IOException:

```
import java.io.BufferedReader;
import java.io.BufferedWriter;
import java.io.File;
import java.io.FileReader;
import java.io.FileWriter;
import java.io.IOException;
import java.util.ArrayList;
import java.util.Scanner;
public class ElectricityManagementSystem {
   public static void main(String[] args) throws IOException {
       int option;
       do {
           System.out.println("Please choose an option:\n1. Register\n2. Login\n3. List record of previous bill\n4. Edit Personal Details\n5. Payment\n6. Erase\n7. Output\n0. Exit");
           Scanner input = new Scanner(System.in);
           option = input.nextInt();
           switch(option) {
               case 0:
                   System.out.println("Exiting program...");
                   break;
               case 1:
                   register();
                   break;
               case 2:
                   login();
                   break;
               case 3:
                   listRecord();
                   break;
               case 4:
                   editPersonalDetails();
                   break;
               case 5:
                   payment();
                   break;
               case 6:
                   erase();
                   break;
               case 7:
                   output();
                   break;
               default:
                   System.out.println("Invalid option, please try again.");
                   break;
           }
       } while(option != 0);
   }
   public static void menu() {
       System.out.println("Welcome to the Electricity Management System");
   }
   public static void register() throws IOException {
       Scanner input = new Scanner(System.in);
       String fileName = "electricity_management_system.txt";
       BufferedWriter output = new BufferedWriter(new FileWriter(fileName, true));
       int id = (int) (Math.random() * 1000);
       System.out.println("Please enter your name:");
       String name = input.nextLine();
       System.out.println("Please enter your address:");
       String address = input.nextLine();
       System.out.println("Please enter your age:");
       int age = input.nextInt();
       System.out.println("Please enter your house number:");
       int houseNumber = input.nextInt();
       System.out.println("Please enter your bill:");
       double bill = input.nextDouble();
       output.write(id + "," + name + "," + address + "," + age + "," + houseNumber + "," + bill + "\n");
       output.close();
       System.out.println("Your ID is " + id + " and your password is " + name + houseNumber);
   }
   public static void login() throws IOException {
       Scanner input = new Scanner(System.in);
       System.out.println("Please enter your ID:");
       int id = input.nextInt();
       System.out.println("Please enter your password:");
       String password = input.nextLine();
       BufferedReader br = new BufferedReader(new FileReader("electricity_management_system.txt"));
       String line = "";
       while((line = br.readLine()) != null) {
           String[] details = line.split(",");
           if(details[0].equals(Integer.toString(id)) && (details[1].equals(password) || details[4].equals(password))) {
               System.out.println("Name: " + details[1]);
               System.out.println("Address: " + details[2]);
               System.out.println("Age: " + details[3]);
               System.out.println("House Number: " + details[4]);
               System.out.println("Bill: " + details[5]);
               break;
           }
       }
       if(line == null) {
           System.out.println("No records were found.");
       }
       br.close();
   }
   public static void listRecord() throws IOException {
       BufferedReader br = new BufferedReader(new FileReader("electricity_management_system.txt"));
       String line = "";
       while((line = br.readLine()) != null) {
           String[] details = line.split(",");
           System.out.println("Name: " + details[1]);
           System.out.println("Bill: " + details[5]);
       }
       br.close();
   }
   public static void editPersonalDetails() throws IOException {
       Scanner input = new Scanner(System.in);
       System.out.println("Please enter your ID:");
       int id = input.nextInt();
       BufferedReader br = new BufferedReader(new FileReader("electricity_management_system.txt"));
       ArrayList lines = new ArrayList();
       String line = "";
       while((line = br.readLine()) != null) {
           String[] details = line.split(",");
           if(details[0].equals(Integer.toString(id))) {
               System.out.println("Please enter your new address:");
               details[2] = input.nextLine();
               System.out.println("Please enter your new phone number:");
               details[4] = input.nextLine();
               line = details[0] + "," + details[1] + "," + details[2] + "," + details[3] + "," + details[4] + "," + details[5];
           }
           lines.add(line);
       }
       br.close();
       BufferedWriter bw = new BufferedWriter(new FileWriter("electricity_management_system.txt"));
       for(String l : lines) {
           bw.write(l + "\n");
       }
       bw.close();
   }
   public static void payment() throws IOException {
       Scanner input = new Scanner(System.in);
       System.out.println("Please enter your ID:");
       int id = input.nextInt();
       BufferedReader br = new BufferedReader(new FileReader("electricity_management_system.txt"));
       ArrayList lines = new ArrayList();
       String line = "";
       while((line = br.readLine()) != null) {
           String[] details = line.split(",");
           if(details[0].equals(Integer.toString(id))) {
 

 ....see the other part on the comment section.

The given Java program is an electricity management system that allows users to register, login, view previous bill records, edit personal details, make payments, erase records, and view the overall output. It uses IOException to handle file input/output operations.

Learn more about Java program: https://brainly.com/question/26789430

#SPJ11

The formula for link utilization is: where L is the distance of 50 km, R is the transmission rate of 1 Mbps, and W is the frame size of 2000 bits.

The velocity of propagation is given as 3x10^8 m/s and the frame error probability is given as 0.1. The Stop-and-Wait ARQ protocol is used.Using the above information, let's calculate the link utilization as follows:Frame Size, W = 2000 bitsTransmission Rate,

frames will be transmitted at a time, and there is a chance that either of these frames may be lost, so a = P (probability of an error occurring) = 0.1Therefore, the link utilization is calculated as follows,Therefore, the link utilization of the given system is 0.68.

To know more about formula  visit:

https://brainly.com/question/20748250

#SPJ11

In the given scenario, if the bridge failed due to design inadequacies and the engineer in charge was responsible for the design and estimation, there may be a potential legal entitlement against the engineer under the principles of professional negligence in tort law.

The legal entitlement that can be levied against the engineer in charge in this case is professional negligence. Professional negligence occurs when a professional fails to exercise a reasonable standard of care, skill, or diligence in performing their duties, resulting in harm or damage to another party. In this situation, the engineer's role was crucial in the design and estimation of the bridge, and the failure during construction suggests that there were design inadequacies.

To establish a claim of professional negligence, certain elements need to be proven. Firstly, it must be demonstrated that the engineer owed a duty of care to the client or the parties affected by the construction of the bridge. This duty is typically established by the professional relationship between the engineer and the client.

Secondly, it must be shown that the engineer breached the duty of care by failing to meet the standard of care expected from a reasonable professional in the same field. The design inadequacies leading to the bridge failure would likely serve as evidence of this breach.

Lastly, it needs to be established that the breach of duty caused harm or damage to the client or other parties involved in the construction project. The failure of the bridge during construction would likely result in financial losses, delays, and potential safety risks.

To determine the specific legal entitlement or the relevant tort case that could be levied against the engineer, it would be necessary to consult the applicable laws and regulations in the jurisdiction where the incident occurred. Tort laws can vary by jurisdiction, so a specific article or case reference cannot be provided without knowing the specific jurisdiction involved. Consulting with legal professionals familiar with the local laws would be essential in pursuing a legal claim.

learn more about design inadequacies  here:
https://brainly.com/question/32273996

#SPJ11

Compute the sum, difference, product, quotient, remainder, and an average of two integers given on the command line. And Calculate the final score needed to get an A in a course based on assignment scores, finals, and recitation scores.

For the first scenario, given two integers as command line arguments, you can compute their sum, difference, product, quotient, remainder, and average using basic arithmetic operations. The program can take the input values, perform the calculations, and print the results accordingly.

In the second scenario, the program can calculate the final score needed to achieve an A in a course based on the average assignment score, scores for final exams, and recitation scores provided as command line arguments.

The formula for computing the final score is given as 0.5a + 0.15e1 + 0.15e2 + 0.15f + 0.05*r, where a, e1, e2, f, and r represent the respective scores. The program can evaluate this formula, determine the final score needed to reach a total score of at least 90, and print the result.

To learn more about “arithmetic operations” refer to the https://brainly.com/question/4721701

#SPJ11

The average power absorbed by the two resistors are as follows:[tex]PL = 3.544 x 10^(-4) WPR = 6.399 x 10^(-4)[/tex]W Hence, the required answer is option C.

Given circuit diagram:[tex]29 0 ww ell 24 2 www 50 cos (9000 t) volts 2 mH 59 μF[/tex]The circuit contains two resistors Rl and Rr, one inductor L and one capacitor C. To find: Average power absorbed by the two resistors Solution: The instantaneous voltage across the capacitor is given as v C = 50 cos(9000t)The instantaneous current through the inductor is given as[tex]i L = 1/L ∫v Cdt[/tex]

Instantaneous voltage across the inductor is given as [tex]vL = L(diL/dt)[/tex] Total voltage across the circuit is given as V = vL + vC ...(1)Average power absorbed by the inductor is zero. The average power absorbed by the capacitor is also zero as it is an ideal capacitor.

To know more about resistors visit:

https://brainly.com/question/30672175

#SPJ11

QoS protocol (Quality of Service) is a protocol that aims to ensure the quality of services of the network. The QoS protocol is a set of technologies that is designed to provide reliable and predictable service levels to all traffic classes on a network. It is responsible for ensuring that each traffic flow is assigned the appropriate level of service according to its priority and required bandwidth. The QoS protocol aims to guarantee the end-to-end delay, packet loss, and bandwidth required by a particular application or service.

The main features of SAR protocol are as follows:

SAR protocol segments the packets to be transmitted into small fixed-sized cells.

The SAR protocol is responsible for the reassembly of cells at the receiving end.

The protocol is used to ensure that the cells arrive at their destination in a timely and efficient manner.SAR protocol is responsible for reducing the impact of congestion and delays in ATM networks.

The SAR protocol provides a link between the higher-level protocols and the physical layer of the network.

What is SAR protocol?

The SAR protocol, also known as Segmentation and Reassembly protocol, is a network protocol used in telecommunications to transmit data over networks that have a maximum transmission unit (MTU) size limitation.

The purpose of the SAR protocol is to break larger data packets into smaller segments that can fit within the MTU size of the network. It ensures that data transmission can occur smoothly by dividing the data into manageable segments and reassembling them at the destination.

The SAR protocol operates at the data link layer of the OSI model and is commonly used in protocols such as ATM (Asynchronous Transfer Mode). It allows for efficient transmission of data by reducing the impact of errors and ensuring reliable delivery of packets.

Learn more about Protocols:

https://brainly.com/question/16224929

#SPJ11

In this problem, ten megawatts of power are being generated and transmitted over a power line of resistance of 4 ohms. Some distance after leaving the generator, the power line passes through a transmission substation equipped with a step-up voltage transformer.

The generator voltage is 10,000 V and the transmission voltage is 130,000 V. We want to find what percent of the original power would be lost if there was no transmission substation to step the voltage up but the wire’s resistance in the transmission system remained unchanged.

Given that the power being transmitted over the power line is 10 MWThe resistance of the power line is 4 ohmsThe generator voltage is 10,000 VThe transmission voltage is 130,000 VNo. of ways to calculate power is

[tex]P=VI (power = voltage × current)P = V²/R (power = voltage² / resistance)P = I²R (power = current² × resistance)[/tex]

To know more about megawatts visit:
https://brainly.com/question/20370289

#SPJ11