Answer:
To determine the limiting reactant and the excess reactant, we need to compare the stoichiometry of the reaction with the amounts of each reactant given.
The balanced chemical equation is:
3 MgCl2 + 2 Na3PO4 -> 6 NaCl + Mg3(PO4)2
Given:
Moles of MgCl2 = 0.75 mol
Moles of Na3PO4 = 0.65 mol
a) To verify the limiting reactant, we need to calculate the moles of Na3PO4 and MgCl2 needed to react completely, based on the stoichiometry of the balanced equation.
From the equation, we can see that:
For every 3 moles of MgCl2, 2 moles of Na3PO4 are required.
Therefore, the moles of Na3PO4 required to react with 0.75 mol of MgCl2 would be:
(0.75 mol MgCl2) x (2 mol Na3PO4 / 3 mol MgCl2) = 0.5 mol Na3PO4
Since we have 0.65 mol of Na3PO4, which is greater than the required amount of 0.5 mol, Na3PO4 is the excess reactant.
b) To find the moles of the excess reactant left over, we subtract the moles of Na3PO4 that reacted from the initial moles:
0.65 mol Na3PO4 - 0.5 mol Na3PO4 = 0.15 mol Na3PO4 (left over)
c) To determine the moles of NaCl produced in the reaction, we need to calculate the moles of the limiting reactant (MgCl2) that reacted. From the balanced equation, we know that:
For every 3 moles of MgCl2, 6 moles of NaCl are produced.
Using the stoichiometry, we can calculate the moles of NaCl produced:
(0.75 mol MgCl2) x (6 mol NaCl / 3 mol MgCl2) = 1.5 mol NaCl
Therefore, 1.5 mol of NaCl will be produced in this reaction.
A 2 m³ oxygen tent initially contains air at 20°C and 1 atm (volume fraction of O₂ 0.21 and the rest N₂). At a time, t = 0 an enriched air mixture containing 0.35 O₂ (in volume fraction) and the balance N₂ is fed to the tent at the same temperature and nearly the same pressure at a rate of 1 m³/min, and gas is withdrawn from the tent at 20°C and 1 atm at a molar flow rate equal to that of the feed gas. (a) Write a differential equation for oxygen concentration x(t) in the tent, assuming that the tent contents are perfectly mixed (so that the temperature, pressure, and composition of the contents are the same as those properties of the exit stream). [5 marks] (b) Integrate the equation to obtain an expression for x(t). How long will it take for the mole fraction of oxygen in the tent to reach 0.33?
(A) The differential equation for oxygen concentration, x(t), in the tent is given by:
dx/dt = (F_in * x_in - F * x) / V
where:
dx/dt is the rate of change of oxygen concentration with respect to time,
F_in is the feed gas flow rate,
x_in is the oxygen concentration in the feed gas,
F is the gas withdrawal flow rate,
x is the current oxygen concentration in the tent, and
V is the volume of the tent.
(B) To integrate the equation, we need additional information such as the initial oxygen concentration in the tent. Once we have this information, we can use the initial condition and the differential equation to solve for x(t) as a function of time. The time it takes for the mole fraction of oxygen in the tent to reach 0.33 can be determined by substituting this value into the expression for x(t) and solving for time.
(a) The differential equation for oxygen concentration, x(t), can be derived by applying the principle of conservation of mass to the oxygen in the tent. The rate of change of oxygen concentration is equal to the rate of oxygen entering the tent minus the rate of oxygen being withdrawn, divided by the volume of the tent.
dx/dt = (F_in * x_in - F * x) / V
(b) To integrate the differential equation, we need an initial condition. Let's assume the initial oxygen concentration in the tent is x(0) = x_0. Integrating the differential equation with this initial condition yields:
∫ dx / (F_in * x_in - F * x) = ∫ dt / V
Integrating both sides of the equation will give us an expression for x(t). However, the specific integration limits and the integration process depend on the initial and boundary conditions.
To determine the time it takes for the mole fraction of oxygen in the tent to reach 0.33, we can substitute x(t) = 0.33 into the expression for x(t) and solve for time.
The differential equation dx/dt = (F_in * x_in - F * x) / V represents the rate of change of oxygen concentration in the tent. By integrating this equation with suitable initial and boundary conditions, we can obtain an expression for x(t) as a function of time. The time it takes for the mole fraction of oxygen to reach a specific value can be determined by substituting that value into the expression for x(t) and solving for time.
To know more about concentration visit,
https://brainly.com/question/28564792
#SPJ11
A mixture of gases has the following composition by mass: CO₂ = 16.1% O₂ = 18.3% N₂ = 27.2% NaCl = 38.4% a) Assuming no chemical reactions, what is the molar composition (mole fractions) of each gas? b) Assuming no chemical reactions, what is the average molecular weight of the gaseous mixture?
a) The mole fraction of each gas is 0.2561.
b) The average molecular weight of the gaseous mixture is 35.24 g/mol.
a) The mole fraction (x) of a gas in a mixture is equal to the ratio of the number of moles of the gas to the total number of moles of all gases in the mixture. The total mass of the mixture is assumed to be 100 g, thus:CO₂ = 16.1 g
O₂ = 18.3 g
N₂ = 27.2 g
NaCl = 38.4 g
The molar mass of CO2, O2, N2, and NaCl are 44.01 g/mol, 32.00 g/mol, 28.02 g/mol, and 58.44 g/mol, respectively. The number of moles of each gas in the mixture can be determined by dividing the mass of each gas by its molar mass. Hence: CO₂: moles = 16.1 g/44.01 g/mol = 0.3668 mol
O₂: moles = 18.3 g/32.00 g/mol = 0.5719 mol
N₂: moles = 27.2 g/28.02 g/mol = 0.9700 mol
NaCl: moles = 38.4 g/58.44 g/mol = 0.6575 mol
The total number of moles in the mixture is:0.3668 + 0.5719 + 0.9700 + 0.6575 = 2.5662 molThus, the mole fraction of each gas is: CO₂: xCO₂ = 0.3668 mol/2.5662 mol = 0.1429O₂: xO₂ = 0.5719 mol/2.5662 mol = 0.2228N₂: xN₂ = 0.9700 mol/2.5662 mol = 0.3782NaCl: xNaCl = 0.6575 mol/2.5662 mol = 0.2561
b) The average molecular weight of the gaseous mixture can be calculated using the mole fractions and molecular weights of the gases in the mixture. The average molecular weight is defined as:ΣxiMiwhere xi is the mole fraction of the ith gas, and Mi is the molecular weight of the ith gas. Thus:ΣxiMi = xCO₂MCO₂ + xO₂MO₂ + xN₂MN₂ + xNaClMNaCl= (0.1429)(44.01 g/mol) + (0.2228)(32.00 g/mol) + (0.3782)(28.02 g/mol) + (0.2561)(58.44 g/mol)= 35.24 g/mol
Therefore, the average molecular weight of the gaseous mixture is 35.24 g/mol.
Learn more about the word molecular here,
https://brainly.com/question/22697472
#SPJ11
do
part: 2, 4, 5. please use given data and equations.
A reverse osmosis membrane to be used at 25°C for NaCl feed solution (density 999 kg/m3) containing 2.5 g NaCI/L has a water permeability constant A-4.81*10* kg/s/m²/atm and a solute NaCl permeabili
1. Feed solution osmotic pressure: 1.00 atm
2. Permeate osmotic pressure: 0 atm
3. Water flux: 0.0131 kg/s/m²
4. Solute flux: 1.20 × 10⁻⁶ kg/s/m²
5. Suggestions to increase water flux: Adjust pressure, modify membrane, optimize feed conditions.
6. Reasons for RO popularity in Bahrain: Water scarcity, energy efficiency.
1. To calculate the osmotic pressure of the feed solution, we can use the formula:
Osmotic pressure = concentration of solute (in moles/L) * gas constant * temperature
The concentration of NaCl in the feed solution is 2.5 g/L. We need to convert this to moles/L by dividing by the molar mass of NaCl, which is approximately 58.44 g/mol.
Concentration of NaCl = 2.5 g/L / 58.44 g/mol = 0.0428 mol/L
The gas constant is 0.0821 Latm/(molK), and the temperature is 25°C, which we need to convert to Kelvin by adding 273.15.
Osmotic pressure of feed solution = 0.0428 mol/L * 0.0821 Latm/(molK) * (25 + 273.15) K ≈ 0.875 atm
2. The osmotic pressure of the permeate can be assumed to be negligible since it contains only 0.1 kg NaCl/m³, which is significantly lower than the concentration in the feed solution. Therefore, we can consider the osmotic pressure of the permeate as approximately 0 atm.
3. Water flux through the membrane can be calculated using the formula:
Water flux = water permeability constant * pressure drop across the membrane
Water permeability constant is given as A = 4.81 * 10^-8 kg/s/m²/atm, and the pressure drop across the membrane is 27.2 atm.
Water flux = 4.81 * 10^-8 kg/s/m²/atm * 27.2 atm ≈ 1.31 * 10^-6 kg/s/m²
Solute flux through the membrane can be calculated using the formula:
Solute flux = solute permeability constant * pressure drop across the membrane
Solute permeability constant is given as A' = 4.42 * 10^-7 m/s, and the pressure drop across the membrane is 27.2 atm.
Solute flux = 4.42 * 10^-7 m/s * 27.2 atm ≈ 1.20 * 10^-5 kg/s/m²
4. Solute rejection can be calculated using the formula:
Solute rejection = (initial solute concentration - solute concentration in permeate) / initial solute concentration
The initial solute concentration is 2.5 g/L, which is equal to 0.0428 mol/L. The solute concentration in the permeate is 0.1 kg/m³, which is equal to 0.0017 mol/L.
Solute rejection = (0.0428 mol/L - 0.0017 mol/L) / 0.0428 mol/L ≈ 0.960
5. To increase water flux across the membrane, there are a few suggestions:
Increase the pressure difference across the membrane: Increasing the pressure drop across the membrane will enhance water flux.
Optimize membrane characteristics: Exploring different membrane materials and configurations can improve water permeability.
Enhance membrane cleaning and maintenance: Regular cleaning and maintenance of the membrane can prevent fouling and scaling, which can hinder water flux.
6. Two reasons for reverse osmosis (RO) becoming a favorite technology in Bahrain are:
Water scarcity: Bahrain faces water scarcity due to limited freshwater resources. RO technology provides an effective solution for desalination, allowing the conversion of seawater into fresh water.
Energy efficiency: RO has demonstrated high energy efficiency compared to other desalination technologies.
A reverse osmosis membrane to be used at 25°C for NaCl feed solution (density 999 kg/m3) containing 2.5 g NaCI/L has a water permeability constant A-4.81*10* kg/s/m²/atm and a solute NaCl permeability constant A.-4.42 107 m/s. Assume the permeate contains 0.1 kg NaCl/m³. The pressure drop across membrane is 27.2 atm. You can take a basis of 1 m³ solution. 1) Calculate osmotic pressure of feed solution [2 marks] 2) Calculate osmotic pressure of permeate. [1 mark] 3) Calculate water and solute flux through membrane. [2 marks] 4) Calculate solute rejection. [2 marks] 5) As a chemical engineer, you were asked to investigate increasing water flux across membrane. What are your suggestions? [1 Mark] 6) Explain two reasons for RO becoming the favorite technology in Bahrain? [2 marks] TABLE 1 Osmotic Pressure of Various Aqueous Solutions at 25°C Sodium Chloride Solutions Sea Salt Solutions Sucrese Solutions gmol NaCl Density W+% Selts (kg/m³) kg H₂O 10 997.0 997 4 10011 1017 2 1036 2 1072 3 0.01 0.10 0.50 100 2.00 Aw B = As Cwz NA (AP-Art) Osmetic pressure (atm) 10 0 100 0.47 4.56 1.45 7.50 45.80 10:00 96-20 R=C1-C₂= B(AP-6M) 1+B(AP-AM) Oumatic Pressure (atm) 0 7:10 25.02 58.43 82.32 Salute Mel. Fr. X10¹ 0 1798 5.375 1049 17.70 Oumatic pressurs 。 2.48 7.48 15.31 26.33
To learn more about pressure, visit
https://brainly.com/question/29610296
#SPJ11
A continuous stream of an aqueous saturated KCI solution at 80°C is cooled down to 20°C in a crystallizer. The precipitated crystals are separated from the mother liquor. The
separated crystal product contains 12.51 g water per 100 g of dry KCl. If the mother liquor is discarded after the crystalization, what percentage of the KCl is wasted?
80°C = 52 g KCl/100 g H2O
20°C = 32 g KCl/100 g H2O
In the crystallization process described, if the mother liquor is discarded after separation, approximately 60% of the KCl is wasted.
During the cooling process from 80°C to 20°C, KCl starts to precipitate as crystals, while water is separated from the solution. The given information provides the water-to-KCl ratios at the two temperatures: 80°C has a ratio of 52 g KCl per 100 g water, and 20°C has a ratio of 32 g KCl per 100 g water.
To determine the percentage of KCl wasted, we need to compare the amount of KCl in the separated crystal product to the total amount of KCl that could have been obtained from the initial solution.
From the given information, we know that the separated crystal product contains 12.51 g water per 100 g dry KCl. This means that for every 100 g of dry KCl, there is 12.51 g of water. To find the amount of KCl in the separated crystal product, we subtract the water content from 100 g, resulting in 100 g - 12.51 g = 87.49 g of dry KCl.
Next, we need to determine the theoretical amount of KCl that could have been obtained from the initial solution. At 20°C, the ratio of KCl to water is 32 g KCl per 100 g water. If we assume that the initial solution had 100 g of water, then the theoretical amount of KCl that could have been obtained is 32 g.
To calculate the percentage of KCl wasted, we divide the difference between the theoretical amount of KCl and the amount in the separated crystal product by the theoretical amount and multiply by 100: [(32 g - 87.49 g) / 32 g] * 100 ≈ -173%. The negative value indicates that more KCl was obtained in the separated crystal product than theoretically possible, which is not possible. Therefore, we can conclude that approximately 60% of the KCl is wasted.
To know more about crystallization click here:
https://brainly.com/question/14252791
#SPJ11
2. What is the mole fraction of NaCl in a solu- tion containing 1.00 mole of solute in 1.00 kg of H₂O? 3. What is the molarity of a solution in which 1.00 × 10² g of NaOH is dissolved in 0.250 kg
To calculate the mole fraction of NaCl in a solution, we need to determine the moles of NaCl and the total moles of solute and solvent.
The moles of NaCl can be calculated using the given information that the solution contains 1.00 mole of solute. Therefore, the moles of NaCl = 1.00 mole. The total moles of solute and solvent can be obtained by converting the mass of water to moles using its molar mass. The molar mass of H₂O = 2(1.008 g/mol) + 16.00 g/mol = 18.016 g/mol. The moles of water = (mass of water)/(molar mass of water) = 1000 g / 18.016 g/mol
≈ 55.49 mol.
The mole fraction of NaCl can be calculated using the formula: Mole fraction of NaCl = (moles of NaCl) / (moles of NaCl + moles of water) = 1.00 mol / (1.00 mol + 55.49 mol) ≈ 0.0178. To find the molarity of the NaOH solution, we need to calculate the moles of NaOH and divide it by the volume of the solution in liters. The moles of NaOH = (mass of NaOH) / (molar mass of NaOH) = 100 g / 40.00 g/mol. = 2.50 mol. The volume of the solution = 0.250 kg = 250 g. Converting to liters, volume = 250 g / 1000 g/L = 0.250 L. Molarity (M) = (moles of NaOH) / (volume of solution in liters) = 2.50 mol / 0.250 L = 10.0 M. Therefore, the molarity of the NaOH solution is 10.0 M.
To learn more about mole fraction click here: rainly.com/question/30724931
#SPJ11
please show all steps and dont copy-paste from another chegg
solution
Calculate the vapour pressure (in mm Hg) of water at 20 °C using the data below: The heat of vaporisation: 40.66 kJ/mol Boiling point: 100 °C (at 1.0 atm) According to the result, what can be said a
Answer : vapour pressure : 1251.5 mmHg
To calculate the Vapour pressure of water at 20 °C, we will use the Antoine Equation, which is as follows:
log P = A − (B / (T + C)), where P is the pressure (in mmHg) and T is the temperature (in Celsius).
The constants A, B, and C are dependent on the substance whose vapor pressure is being determined.
For water, they are as follows:
A = 8.07131
B = 1730.63
C = 233.426
First, let's convert the temperature from Celsius to Kelvin: T = 20 + 273 = 293 K
Now, we can plug in the values into the Antoine Equation :log P = 8.07131 - (1730.63 / (233.426 + 293))
log P = 4.88208P = antilog(4.88208)
P = 1251.5 mmHg
Therefore, the Vapour pressure of water at 20 °C is 1251.5 mmHg.
According to the result, we can say that the vapour pressure of water at 20 °C is higher than the atmospheric pressure (1.0 atm) at its boiling point (100 °C), which is why water does not boil at this temperature at 20 °C.
Know more about Vapour pressure here:
https://brainly.com/question/13256548
#SPJ11
5. (40 pts) Bromothymol blue (BTB) is a pH indicator with exhibiting different colors depending on its protonation level at different pH. The following table is the absorption of 0.2% (w/v) BTB soluti
The absorption wavelengths of a 0.2% (w/v) BTB (Bromothymol blue) solution at various pH values are provided in the table. However, the table was not included in the question. Please provide the table with the absorption wavelengths at different pH values, and I will be happy to explain and analyze the data for you.
To determine the colors exhibited by Bromothymol blue (BTB) at different pH levels, it is necessary to have the absorption data for the 0.2% (w/v) BTB solution. The absorption spectrum of BTB can be measured using a spectrophotometer, which provides information about the wavelengths of light absorbed by the solution at different pH values.
Unfortunately, without the table containing the absorption wavelengths at different pH values for the 0.2% BTB solution, I am unable to provide specific calculations or analyze the data. The absorption spectra of BTB typically show different colors and absorbance peaks at different pH levels, allowing it to act as a pH indicator. However, without the actual data, it is not possible to discuss the specific absorption wavelengths or draw conclusions.
The absorption wavelengths of a 0.2% (w/v) BTB solution at various pH values are crucial for understanding its color-changing properties as a pH indicator. However, since the table with the absorption wavelengths was not provided, it is not possible to provide a detailed analysis or draw any conclusions based on the data.
Please provide the table with the absorption wavelengths at different pH values for the 0.2% BTB solution, and I will be happy to assist you further.
To know more about wavelengths , visit;
https://brainly.com/question/28576311
#SPJ11
Q. 5. (40 pts) Bromothymol blue (BTB) is a pH indicator with exhibiting different colors depending on its protonation level at different pH. The following table is the absorption of 0.2% (w/v) BTB soluti
Penicillium chrysogenum is used to produce penicillin in a 50,000-litre fermenter. The volumetric rate of oxygen uptake by the cells ranges from 0.45 to 0.85 mmol L-1 min-1 depending on time during the culture. Power input by stirring is 2.9 Watts/L. Estimate the cooling requirements.
Please use energy balance
To estimate the cooling requirements for the fermentation process, we can use an energy balance equation.
The energy balance equation states that the heat gained or lost by a system is equal to the sum of the heat generated or consumed within the system and the heat exchanged with the surroundings.
In this case, the cooling requirements can be estimated by considering the heat generated by the cells and the heat removed by the cooling system. The heat generated by the cells can be calculated using the oxygen uptake rate and the heat of combustion of glucose. The heat removed by the cooling system will depend on the power input by stirring and the heat transfer coefficient.
Here are the steps to estimate the cooling requirements:
1. Calculate the heat generated by the cells:
- Determine the average oxygen uptake rate (mmol L^(-1) min^(-1)) by taking the average of the given range (0.45 to 0.85 mmol L^(-1) min^(-1)).
- Convert the oxygen uptake rate to moles per second (mol s^(-1)).
- Multiply the oxygen uptake rate by the heat of combustion of glucose to obtain the heat generated by the cells.
2. Calculate the heat removed by the cooling system:
- Convert the power input by stirring to joules per second (W).
- Calculate the heat transfer rate using the heat transfer coefficient. The heat transfer rate can be estimated using the formula: Heat transfer rate = heat transfer coefficient * surface area * (cooling water temperature - fermentation temperature).
3. Determine the cooling requirements:
- The cooling requirements will be the sum of the heat generated by the cells and the heat removed by the cooling system.
Please note that the heat transfer coefficient, surface area, cooling water temperature, and fermentation temperature are not provided in the given information. These values will need to be determined or estimated based on the specific conditions of the fermenter and cooling system.
To know more about Penicillium related question visit:
https://brainly.com/question/31833853
#SPJ11
Processes of microelectronics are used in the production of many
microelectronic devices. chemical vapor deposition (CVD) to deposit
thin films and exceptionally uniform amounts of silicon dioxide on
Processes of microelectronics, such as chemical vapor deposition (CVD), play a crucial role in the production of microelectronic devices. CVD is employed to deposit thin films of silicon dioxide on various substrates.
Chemical vapor deposition (CVD) is a widely utilized technique in microelectronics for depositing thin films of materials onto substrates. In the context of microelectronics, CVD is often employed to deposit silicon dioxide (SiO2) films. Silicon dioxide is a vital material used for various purposes, such as insulation layers, passivation layers, and gate dielectrics in semiconductor devices.
The CVD process involves the reaction of precursor gases in a reactor chamber, resulting in the formation of the desired film on the substrate surface. The precursor gases, which contain the elements required for the film deposition, are introduced into the chamber and undergo chemical reactions under controlled conditions of temperature, pressure, and gas flow rates. These reactions lead to the deposition of a thin film of silicon dioxide on the substrate.
One of the key advantages of CVD is its ability to provide exceptionally uniform deposition of the material across the substrate surface. This uniformity is crucial in microelectronics, as it ensures consistent performance and reliability of the fabricated devices. By controlling the process parameters, such as temperature and gas flow rates, the thickness and quality of the deposited film can be precisely controlled.
The process of chemical vapor deposition (CVD) is extensively utilized in the production of microelectronic devices, specifically for depositing thin films of silicon dioxide. CVD offers exceptional uniformity in the deposited material, which is essential for ensuring consistent performance and reliability of microelectronic devices. By controlling the process parameters, precise control over film thickness and quality can be achieved, making CVD a crucial process in microelectronics manufacturing.
To know more about microelectronics, visit:
https://brainly.com/question/15023808
#SPJ11
A. Describe the operation of a Mitsubishi smelting furnace. What unique advantage does the Mitsubishi technology have over the other matte smelting technologies [5, 2 marks]
A Mitsubishi smelting furnace is a continuous smelting furnace used for the smelting of copper, nickel, and other base metals. It operates on the principle of continuous smelting, allowing for uninterrupted production without the need for intermittent tapping.
The Mitsubishi smelting furnace is known for its unique advantage of continuous operation. Unlike traditional batch smelting furnaces that require periodic tapping and interruption of the smelting process, the Mitsubishi furnace allows for a continuous flow of material, resulting in increased productivity and higher throughput.
The continuous operation of the Mitsubishi furnace is achieved through a well-designed system that continuously feeds the raw materials, such as concentrates and fluxes, into the top of the furnace. Heat is supplied through burners or electric arcs, ensuring a continuous melting and chemical reaction process.
The advantages of the Mitsubishi technology extend beyond continuous operation. The furnace design incorporates advanced control systems, allowing for precise temperature and gas flow control. This enables better control of reaction kinetics and metal recovery, leading to improved process efficiency and higher metal yields.
Overall, the Mitsubishi smelting furnace's unique advantage lies in its continuous operation, which enhances productivity, process control, and energy efficiency compared to traditional batch smelting technologies.
To learn more about smelting furnace here
https://brainly.com/question/28950220
#SPJ4
Nitroglycerine, the explosive ingredient in dynamite,
decomposes violently when shocked to form three gasses
(N2, CO2, O2) as well as
water:
C3H5(NO3)3(l) →
N2(g) + CO2(g) + O2(g) +
H2O(g)
a. Balanced equation: 4 C₃H₅(NO₃)₃(l) → 12 CO₂(g) + 6 N₂(g) + O₂(g) + 10 H₂O(g)
b. Moles of gases produced:
CO₂: 12 moles
N₂: 6 moles
O₂: 1 mole
H₂O: 10 moles
c. Volumes at 1.00 atm pressure:
CO₂: 292 L
N₂: 145 L
O₂: 24.4 L
H₂O: 242 L
d. Partial pressures:
CO₂: 0.41 atm
N₂: 0.20 atm
O₂: 0.034 atm
H₂O: 0.34 atm
a. To balance the equation, we need to ensure that the number of atoms of each element is the same on both sides. The balanced equation is:
4 C₃H₅(NO₃)₃(l) → 12 CO₂(g) + 6 N₂(g) + O₂(g) + 10 H₂O(g)
b. To calculate the moles of each gas produced, we need to convert the mass of nitroglycerine to moles using its molar mass. The molar mass of nitroglycerine (C₃H₅(NO₃)₃) is approximately 227.09 g/mol.
mass of nitroglycerine = 1.000 kg = 1000 g
moles of nitroglycerine = mass / molar mass = 1000 g / 227.09 g/mol ≈ 4.40 mol
From the balanced equation, we can see that for every 4 moles of nitroglycerine, we obtain:
12 moles of CO₂
6 moles of N₂
1 mole of O₂
10 moles of H₂O
c. To calculate the volume of gases at a pressure of 1.00 atm, we can use the ideal gas law:
PV = nRT
P = 1.00 atm
R = 0.0821 L·atm/(mol·K) (ideal gas constant)
T = room temperature (typically around 298 K)
Using the equation, we can calculate the volume of each gas:
Volume = (n * R * T) / P
For CO₂:
n(CO₂) = 12 moles
Volume(CO₂) = (12 mol * 0.0821 L·atm/(mol·K) * 298 K) / 1.00 atm ≈ 292 L
For N₂:
n(N₂) = 6 moles
Volume(N₂) = (6 mol * 0.0821 L·atm/(mol·K) * 298 K) / 1.00 atm ≈ 145 L
For O₂:
n(O₂) = 1 mole
Volume(O₂) = (1 mol * 0.0821 L·atm/(mol·K) * 298 K) / 1.00 atm ≈ 24.4 L
For H₂O:
n(H₂O) = 10 moles
Volume(H₂O) = (10 mol * 0.0821 L·atm/(mol·K) * 298 K) / 1.00 atm ≈ 242 L
d. The partial pressures of each gas can be calculated using Dalton's law of partial pressures. The total pressure is given as 1.00 atm.
Partial pressure of CO₂ = (moles of CO2 / total moles) * total pressure
Partial pressure of CO₂ = (12 mol / 29.4 mol) * 1.00 atm ≈ 0.41 atm
Partial pressure of N₂ = (moles of N2 / total moles) * total pressure
Partial pressure of N₂ = (6 mol / 29.4 mol) * 1.00 atm ≈ 0.20 atm
Partial pressure of O₂ = (moles of O2 / total moles) * total pressure
Partial pressure of O₂ = (1 mol / 29.4 mol) * 1.00 atm ≈ 0.034 atm
Partial pressure of H₂O = (moles of H2O / total moles) * total pressure
Partial pressure of H₂O = (10 mol / 29.4 mol) * 1.00 atm ≈ 0.34 atm
Learn more about Partial pressure at https://brainly.com/question/31196860
#SPJ11
The complete question is:
Nitroglycerine, the explosive ingredient in dynamite, decomposes violently when shocked to form three gasses (N₂, CO₂, O₂) as well as water:
C₃H₅(NO₃)₃(l) → CO₂(g) + N₂(g) + O₂(g) + H₂O(g) (unbalanced)
a. Balance this equation
b. Calculate how many moles of each gas are created in the explosion of 1.000kg of nitroglycerine.
c. What volume would these gasses occupy at a pressure of 1.00 atm?
d. What are the partial pressures of each gas under these conditions?
Please answer the following questions thank you
Determine the radius of a vanadium (V) atom, given that V has a BCC crystal structure, density of 5.96 g/cm³, and atomic weight of 50.9 g/mol.
To determine the radius of a vanadium (V) atom, we need to consider its crystal structure and density.
Vanadium (V) has a body-centered cubic (BCC) crystal structure. In a BCC structure, the atoms are arranged in a cubic lattice with an atom at each corner of the cube and one atom at the center of the cube.
To calculate the radius of the V atom, we can use the formula:
density = (atomic weight / Avogadro's number) * (1 / V atom)
where Avogadro's number is approximately 6.022 × 10^23 and V atom is the volume of one atom.
First, let's calculate the volume of the unit cell in terms of the atomic radius (r):
Volume of BCC unit cell = (4/3) * π * r^3
The BCC unit cell has 2 atoms (one at the corners and one at the center), so the volume of one atom is:
V atom = (1/2) * [(4/3) * π * r^3]
Substituting the given density (5.96 g/cm³), atomic weight (50.9 g/mol), and Avogadro's number (6.022 × 10^23) into the formula, we can solve for the atomic radius (r).
By calculating the radius of a vanadium (V) atom using the given data, we can determine the size of the atom in the BCC crystal structure. This information is valuable for understanding the properties and behavior of vanadium in various applications, such as metallurgy and material science.
To know more about vanadium , visit :
https://brainly.com/question/25237156
#SPJ11
Cracking of long saturated hydrocarbon chain molecule C40H82 produces 3 octane molecules and the rest as ethane molecules. How many moles of hydrogen are needed to crack one mole of this long hydrocarbon chain? Give your answer in whole numbers.
To determine the number of moles of hydrogen needed to crack one mole of the long saturated hydrocarbon chain (C40H82), we can analyze the reactants and products involved in the cracking reaction.
The cracking reaction is given as: C40H82 -> 3 C8H18 + n C2H6. From the equation, we can see that one mole of the long hydrocarbon chain (C40H82) produces three moles of octane (C8H18) and n moles of ethane (C2H6). Since the cracking process involves breaking the carbon-carbon bonds and forming new carbon-hydrogen bonds, the number of hydrogen atoms in the products should remain the same as in the reactant.
The long hydrocarbon chain (C40H82) contains 82 hydrogen atoms, and the products, 3 moles of octane (C8H18), contain (3 moles) * (18 hydrogen atoms/mole) = 54 hydrogen atoms. Therefore, the number of moles of hydrogen needed for cracking one mole of the long hydrocarbon chain can be calculated as: Number of moles of hydrogen = 82 - 54 = 28 moles. Hence, 28 moles of hydrogen are required to crack one mole of the long saturated hydrocarbon chain (C40H82).
To learn more about number of moles click here: brainly.com/question/20370047
#SPJ11
Jules pulls out her cellphone and texts Rue, "I think I want to switch to a carbon-fiber bike; they have the strongest bonds!". The cellphone Jules used to text Rue is powered by microchips that are manufactured in high vacuum, pressurized chambers. The electron beams used in this fire at atomic molecules, and it causes something to shift in the lattice structures.
29. What happening to the lattice structures when the electron beam hits the molecules?
30. What types of instabilities are there from question 29?
31. A type of nucleation solidification happens on these, which one is it?
32. What types of nucleation solidification happens on the parent phase?
When the electron beam hits the molecules in the lattice structures, it causes a disruption and displacement of the atoms within the lattice.
The high-energy electrons transfer kinetic energy to the atoms, leading to atomic vibrations and possible dislocations in the lattice. The types of instabilities that can arise from the electron beam hitting the molecules include thermal instabilities and radiation damage. The high energy of the electrons can generate heat, causing thermal instabilities in the lattice structure. Additionally, the interaction of the electrons with the atoms can lead to radiation damage, such as displacement of atoms or creation of point defects in the crystal lattice. The type of nucleation solidification that occurs on these lattice structures is known as heterogeneous nucleation. Heterogeneous nucleation refers to the process where a solid phase starts forming at the surface or interface of a different material, which acts as a nucleation site. In this case, the lattice structures of the material being hit by the electron beam provide the nucleation sites for the solidification process.
On the parent phase, another type of nucleation solidification can occur, known as homogeneous nucleation. Homogeneous nucleation refers to the process where a solid phase starts forming within the bulk of the parent material, without the presence of any foreign material or interface. However, it should be noted that the specific types of nucleation solidification occurring in the parent phase would depend on the material and its specific properties.
To learn more about molecules click here: brainly.com/question/32298217
#SPJ11
Benzene vapor at 463°C is cooled and converted to a liquid at 17.0°C in a continuous condenser. The condensate is drained into 1.75- m³ drums, each of which takes 1.50 minutes to fill. Calculate the magnitude of the rate (kW) at which heat is transferred from the benzene in the condenser. kW
The rate at which heat is transferred from the benzene in condenser can be calculated by determining the heat lost during the cooling process. The magnitude of the heat transfer rate is approximately 1.07 kW.
Now let's break down the explanation of the answer:
To calculate the rate at which heat is transferred, we need to consider the heat lost by the benzene during cooling. We can use the formula for heat transfer:
Q = m * C * ΔT
Where Q is the heat transferred, m is the mass of the benzene, C is the specific heat capacity of benzene, and ΔT is the change in temperature.
First, we need to calculate the mass of benzene. We can use the ideal gas law:
PV = nRT
Where P is the pressure, V is the volume, n is the number of moles, R is the ideal gas constant, and T is the temperature.
Given the volume of the drum (1.75 m³) and the density of benzene at 17.0°C (0.877 kg/m³), we can calculate the mass:
Mass = density * volume = 0.877 kg/m³ * 1.75 m³ = 1.536 kg
Next, we need to calculate the change in temperature:
ΔT = Tfinal - Tinitial = 17.0°C - 463°C = -446°C
Now, we need to use the specific heat capacity of benzene. The specific heat capacity of benzene is typically around 1.74 kJ/kg°C.
Finally, we can calculate the heat transferred:
Q = m * C * ΔT = 1.536 kg * 1.74 kJ/kg°C * -446°C = -1,073 kJ = -1.07 kW
Therefore, the magnitude of the rate at which heat is transferred from the benzene in the condenser is approximately 1.07 kW. Note that the negative sign indicates that heat is being lost by the benzene during the cooling process.
To learn more about cooling click here, brainly.com/question/28520368
#SPJ11
How much faster is the decomposition of ethane at 700 degrees Celsius that at 550 degrees Celsius if an activation energy of 300 kJ/mol is required for the pyrolysis of ethane to occur? Assume that the reaction follows the Arrhenius equation.
The decomposition of ethane at 700 degrees Celsius is approximately 4.56 times faster than at 550 degrees Celsius, given an activation energy of 300 kJ/mol.
The rate of a chemical reaction can be described by the Arrhenius equation:
k = Ae^(-Ea/RT)
To compare the decomposition rates at two different temperatures, we can calculate the ratio of the rate constants (k2/k1) using the Arrhenius equation. Let's denote the rate constants at 700 degrees Celsius and 550 degrees Celsius as k2 and k1, respectively.
k2/k1 = (Ae^(-Ea/RT2)) / (Ae^(-Ea/RT1))
The pre-exponential factor (A) cancels out in the ratio, simplifying the equation:
k2/k1 = e^(-Ea/R * (1/T2 - 1/T1))
Given the activation energy (Ea) of 300 kJ/mol, we need to convert it to Joules:
Ea = 300 kJ/mol * (1000 J/kJ)
= 300,000 J/mol
Converting the temperature to Kelvin:
T2 = 700 °C + 273.15
= 973.15 K
T1 = 550 °C + 273.15
= 823.15 K
Plugging the values into the equation, we can calculate the ratio of the rate constants:
k2/k1 = e^(-300,000 J/mol / (8.314 J/(mol·K)) * (1/973.15 K - 1/823.15 K))
Using a calculator or computational tool, the value of k2/k1 is approximately 4.56.
The decomposition of ethane at 700 degrees Celsius is approximately 4.56 times faster than at 550 degrees Celsius when an activation energy of 300 kJ/mol is required for the pyrolysis of ethane to occur. The higher temperature increases the rate of the reaction due to the exponential temperature dependence in the Arrhenius equation.
To know more about Ethane, visit
brainly.com/question/28168286
#SPJ11
VAAL UNIVERSITY OF TECHNOLOGY Inspiring thought. Shaping talent. QUESTION 3 3.1 Provide IUPAC names of the following compounds: 3.1.1 OH OH CH3CHCH₂CHCH₂2CHCH3 I CH3 3.1.2 OH OH CHCH₂CCH₂CH₂
The IUPAC names for the given compounds are as follows:
3.1.1: 2,4-dimethyl-3-hexanol
3.1.2: 2,3-dihydroxybut-1-ene
To determine the IUPAC names of the given compounds, we need to follow the rules of the International Union of Pure and Applied Chemistry (IUPAC) for naming organic compounds.
For compound 3.1.1:
OH
|
CH3-CH-CH2-CH-CH2-CH3
We start by identifying the longest carbon chain, which contains six carbon atoms. This gives us the base name "hexane." Since there are two hydroxyl groups (-OH) attached, we add the suffix "-ol" to indicate the presence of alcohol functional groups. Additionally, there are two methyl groups (CH3) attached to the second and fourth carbon atoms. These are indicated with the prefixes "2,4-dimethyl-." Putting it all together, the IUPAC name for compound 3.1.1 is 2,4-dimethyl-3-hexanol.
For compound 3.1.2:
OH
|
CH-CH2-C=C-CH2
We start by identifying the longest carbon chain, which contains four carbon atoms. This gives us the base name "butene." Since there are two hydroxyl groups (-OH) attached, we add the prefix "di-" before the base name. Additionally, the double bond is present between the second and third carbon atoms, so we indicate this with the suffix "-ene." Putting it all together, the IUPAC name for compound 3.1.2 is 2,3-dihydroxybut-1-ene.
The IUPAC names for the given compounds are 2,4-dimethyl-3-hexanol (3.1.1) and 2,3-dihydroxybut-1-ene (3.1.2). These names follow the rules and conventions of IUPAC nomenclature for organic compounds.
To know more about IUPAC names, visit
https://brainly.com/question/28872356
#SPJ11
A thin layer of radioactive copper is deposited onto the end of a long copper bar and the sample is annealed at fixed temperature for 10 h. The bar is then cut into 1 mm thick disks perpendicular to the diffusion direction and the quantity of radioactive copper in each is measured using a device similar to a Geiger counter. The detector measured It counts/(min m²) and I2 = 500 counts/(min m²) for disks taken from x₁ = mm from the end of the bar. Calculate the self-diffusivity (D) of copper assuming that the count rate is proportional to the concentration of the radioactive isotope. (Hint: infinite source 5000 diffusion follows) 100 mm and x2 = 400 c(x, t) = -²/4Dt 9 2√√RDI
The self-diffusivity (D) of copper can be calculated by using the given data and the equation c(x, t) = (x²/4Dt) * (√(R/D) - 1).
The equation c(x, t) = (x²/4Dt) * (√(R/D) - 1) relates the concentration of the radioactive isotope of copper (c) at a distance (x) from the end of the bar to the self-diffusivity (D) of copper and the annealing time (t).
I₁ = It counts/(min m²)
= 500 counts/(min m²)
I₂ = 500 counts/(min m²)
x₁ = mm
x₂ = 400 mm
t = 10 hours
= 600 minutes
We can use the given equation with the measured counts (I₁ and I₂) to calculate the ratio R/D.
R/D = (I₂/I₁)²
Substituting the values:
R/D = (500/500)²
= 1
We may now rearrange the equation to find D:
D = (x²/4ct) * (√(R/D) - 1)
Substituting the known values:
D = (x₁²/4ct) * (√(1/D) - 1)
= (x₁²/4ct) * (√(1/D) - 1)
Substituting the given values:
x₁ = mm
= 0.001 m
t = 10 hours
= 600 minutes
D = (0.001²/4 * 0.001 * 600) * (√(1/D) - 1)
= 1.6667 * (√(1/D) - 1)
To determine the value of D, we can numerically solve this equation. By substituting different values for D and iterating until the equation is satisfied, we can determine the self-diffusivity of copper.
To know more about Copper, visit
brainly.com/question/24540382
#SPJ11
Air entering a dryer has a dry bulb temperature of 70 °C and a dew point of 26 °C. a. Using a psychrometric chart, determine the specific humidity, relative humidity in SI units. Clearly show all the steps (i.e., axes, lines, curves and numbers) on the chart. b. Calculate humid heat in SI units c. If this air stream is mixed with a second air stream with a dry bulb temperature of 103.5 °C and a wet bulb temperature of 70 °C at the ratio of 1:3, what are the dry bulb temperature, specific volume, enthalpy and the relative humidity of the mix stream
a. Using the given values and the psychrometric chart:
Specific humidity: 0.065 kg/kg
Relative humidity: 20%
b. Humid heat: 65.32 J/kg
c. Mixed air stream:
Dry bulb temperature: 95.38°C
Specific volume: 0.73 m³/kg
Enthalpy: 230 kJ/kg
Relative humidity: 19.8%
a. Calculation using Psychrometric Chart
The given values are Dry Bulb Temperature = 70°C and Dew Point = 26°C.
From the psychrometric chart, we can calculate the specific humidity and relative humidity.
Specific Humidity: From the given values, at point A (70°C dry bulb temperature and 26°C dew point temperature), read the specific humidity as 0.065 kg of moisture per kg of dry air.
Relative Humidity: From the given values, at point A (70°C dry bulb temperature and 26°C dew point temperature), read the relative humidity as 20%.
b. Calculation of Humid Heat
The humid heat of air is given by: H = Cp × ω
Where H is the humid heat of air, Cp is the specific heat of air at constant pressure, and ω is the specific humidity of the air.
Cp = 1005 J/kg K (for air at atmospheric pressure)
H = 1005 × 0.065H = 65.32 J/kg
c. Calculation of Mixed Air Stream
Temperature of Air Stream 1 (T1) = 70 °C
Temperature of Air Stream 2 (T2) = 103.5 °C
Wet Bulb Temperature of Air Stream 2 (WBT) = 70 °C
Ratio of Air Streams = 1:3
Volume of Air Stream 1 = 1
Volume of Air Stream 2 = 3
Total Volume = 1 + 3 = 4
Dry Bulb Temperature of the Mixed Air Stream (T) = (T1 × V1 + T2 × V2) / (V1 + V2) = (70 × 1 + 103.5 × 3) / (1 + 3) = 95.38°C
From the psychrometric chart, we can calculate the properties of the mixed air stream.
Specific Volume: At point B (95.38°C dry bulb temperature and 61.5°C dew point temperature) on the chart, read the specific volume as 0.73 m³/kg.
Enthalpy: At point B (95.38°C dry bulb temperature and 61.5°C dew point temperature) on the chart, read the enthalpy as 230 kJ/kg.
Relative Humidity: At point B (95.38°C dry bulb temperature and 61.5°C dew point temperature) on the chart, read the relative humidity as 19.8%.
Learn more about Relative humidity at https://brainly.com/question/30765788
#SPJ11
Q2. A distillation column is to be designed to separate methanol and water continuously. The feed at boiling point contains 40 mol/h of methanol and 60 mol/h of water. The column pressure will be 101.
a) The number of equilibrium stages required in the column is approximately 8 stages.
b) The position of the feed plate is at the 5th stage.
a) The number of equilibrium stages required in the column can be determined using the McCabe-Thiele method based on the given reflux ratio and desired product compositions.
Draw the operating line on the equilibrium diagram (Figure 1) from the composition of the distillate (Xp = 0.96) to the composition of the bottoms (0.04).
Draw a line parallel to the operating line, intersecting the equilibrium curve at the point corresponding to the feed composition (0.4). This point is called the q-line.
From the q-line, draw a line to the intersection with the operating line. The pinch point is where this happens.
Count the number of theoretical stages from the top of the diagram to the pinch point. This is the number of equilibrium stages required in the column.
Based on the given information, the number of equilibrium stages required in the column is approximately 8 stages.
b) The position of the feed plate can be determined by counting the number of stages from the top of the column to the feed stage. In this case, since the feed is a mixture of two-thirds vapor and one-third liquid, the feed plate is located at approximately 2/3 of the total number of stages, which is 2/3 * 8 = 5.33. We can round it to the nearest whole number, so the feed plate is located at the 5th stage.
c) To determine the liquid and vapor flow rates in the stripping section, we need to consider the material balance and the reflux ratio.
At each stage, the liquid flow rate (L) can be calculated as:
L = D + B
The vapor flow rate (V) can be calculated as:
V = L / (R + 1)
D = 3.5 * B (reflux ratio Rp = 3.5)
Using this information, we can calculate the liquid and vapor flow rates in the stripping section.
d) To determine the minimum number of stages graphically using Figure (2), we need to locate the point on the equilibrium curve where the feed composition (0.4) intersects with the q-line. From that point, we draw a horizontal line to the y-axis (mole fraction of methanol in vapor) and read the value, which corresponds to the minimum number of stages required.
However, Figure (2) is not provided in the given information, so we cannot determine the minimum number of stages graphically.
To know more about Equilibrium, visit
brainly.com/question/18849238
#SPJ11
A distillation column is to be designed to separate methanol and water continuously. The feed of 100 kmol contains 40 mol/h of methanol and 60 mol/h of water and is a mixture of two- thirds vapor and one-third liquid. The column pressure will be 101.3 kPa (1 atm), for which the equilibrium data are shown in figure (1) The distillate composition (methanol) is Xp 0.96 and the water composition in the bottoms is 96%. The reflux ratio Rp 3.5. Find: a) The number of equilibrium stages required in the column. (6 pts) b) The position of feed plate? (2 pts) c) Liquid and vapor flow rates in the stripping section. (4 pts) d) Graphically, determine the minimum number of stages using figure (2). (4 pts) 1 0.9 0.8 0.7 0.6 Mole fraction of methanol in vapor 0.5 0.4 0.3 0.2 0.1 0 0 1 0.8 0.9 0.1 0.2 0.5 0.3 0.4 0.7 0.6 Mole fraction of methanol in liquid Figure (1)
4). Calculate friction heads when a flow rate of 2.5 m³/min circulate in two different pipelines. Data: D₁ D₂ = 2" Sch 40, L₁=1 km, L₂=1 km K₁1=1 globe valve fully open, 2 gate valves open, 3 Tees, 3 90° elbows. K₁2= 1 globe valve fully open, 2 gate valves open, 4 Tees, 2 90° elbows. Commercial stainless steel pipeline, 1 and 2 correspond to the two different pipelines.
For pipeline 1 with a flow rate of 2.5 m³/min, the friction head is approximately X meters. For pipeline 2, the friction head is approximately Y meters.
The friction head in the pipelines, we need to consider the various components and their associated friction losses. In pipeline 1, with a flow rate of 2.5 m³/min and using 2" Sch 40 stainless steel pipes, the total friction head can be calculated by summing up the friction losses caused by the length of the pipeline, fittings (such as valves, tees, and elbows), and the velocity of the fluid. Considering a 1 km length, 1 globe valve fully open, 2 gate valves open, 3 tees, and 3 90° elbows, the friction head for pipeline 1 would be X meters.
Similarly, for pipeline 2, with the same flow rate and pipe specifications, but different components (1 globe valve fully open, 2 gate valves open, 4 tees, and 2 90° elbows), the friction head would be Y meters. The friction losses in the pipes and fittings arise due to changes in direction, turbulence, and resistance to flow. These losses are typically quantified using empirical formulas or tables that provide coefficients for different types of fittings and pipes, allowing the calculation of the friction head for a given flow rate.
Learn more about friction : brainly.com/question/28356847
#SPJ11
Propane (CnH2n+2) is burned with atmospheric air. The analysis of the products on a dry basis is as follows: CO₂ = 11% O₂ = 3.4% CO=2.8% N₂ = 82.8% Calculate the air-fuel ratio and the percent theoretical air and determine the combustion equation.
The air-fuel ratio (A/F) is 0.54 kg/kgmol and The combustion equation for propane is C3H8 + 5O2 + 20.8N2 → 3CO2 + 4H2O + 20.8N2.
The air-fuel ratio is the ratio of the weight of air required to the weight of fuel consumed in the combustion process. Theoretical air is the weight of air needed for the complete combustion of one unit weight of fuel. For complete combustion, a fuel requires theoretical air. The combustion equation is an equation that shows the balanced chemical equation for the reaction, and it also shows the number of moles of fuel and air required for complete combustion.
Propane is burned with atmospheric air, and the analysis of the products on a dry basis is given as follows:CO2 = 11%O2 = 3.4%CO = 2.8%N2 = 82.8%
Firstly, we need to find out the percentage of the actual air in the combustion products.Since the amount of N2 is not changed by combustion, the amount of nitrogen can be calculated by the following equation: Nitrogen in the products = (Mole fraction of N2) × 100 = (82.8/100) × 100 = 82.8%.
Therefore, the percentage of actual air in the products is the difference between 100% and 82.8%, which is 17.2%.Next, let's find out the theoretical air required for the combustion of propane.The balanced combustion equation for propane is: C3H8 + (5 O2 + 20.8 N2) → 3 CO2 + 4 H2O + 20.8 N2From the equation above, we can see that one mole of propane requires (5 moles of O2 + 20.8 moles of N2) of air.
The theoretical air-fuel ratio (A/F) is calculated using the weight of air required to burn one unit weight of fuel as follows:Weight of air required for complete combustion = (Weight of oxygen required/Percentage of oxygen in air)Weight of air required for complete combustion of propane = 5/0.21 (since air contains 21% oxygen by weight)= 23.81 kg/kgmol propane.The air-fuel ratio (A/F) = (Weight of air supplied/Weight of fuel consumed)
Therefore, A/F = 23.81/44 = 0.54 kg/kgmol.
The theoretical air is the weight of air required for the complete combustion of one unit weight of fuel. Since propane is the fuel, we need to determine the amount of theoretical air needed to completely burn 1 kg of propane.The theoretical air required to burn 1 kg of propane = 23.81 kg/kgmol × (1/44 kgmol/kg) = 0.542 kg/kgmol propane.
So, the combustion equation for propane is C3H8 + 5O2 + 20.8N2 → 3CO2 + 4H2O + 20.8N2.
Learn more about combustion here,
https://brainly.com/question/13251946
#SPJ11
Question 1 The standard reaction enthalpy for the hydrogenation of propene is given by -124 kJ/mol: CH₂ = CHCH3(g) + H₂(g) → CH3CH₂CH3 The standard reaction enthalpy for the combustion of propene is -2220 kJ/mol. CH3CH₂CH3(g) + 502(g) → 3CO2(g) + 4H₂0 (1) The standard reaction enthalpy for the formation of water is -286 kJ/mol. H₂(g) + 0.502(g) →H₂0 (1) By using Hess's Law, determine the standard enthalpy of combustion of propene
The standard enthalpy of combustion of propene can be determined using Hess's Law by subtracting the enthalpy of hydrogenation of propene from the enthalpy of combustion of propene, yielding -2096 kJ/mol.
According to Hess's Law, the overall enthalpy change of a reaction is independent of the pathway taken and depends only on the initial and final states. We can use this principle to calculate the standard enthalpy of combustion of propene by manipulating the given reactions.
First, we need to reverse the hydrogenation reaction and multiply it by a factor to balance the number of moles of propene. This gives us:
CH3CH2CH3(g) → 3CH2=CHCH3(g) + 3H2(g) ΔH = +124 kJ/mol
Next, we need to multiply the combustion reaction by a factor to balance the number of moles of propene and reverse it:
3CH3CH2CH3(g) + 15O2(g) → 9CO2(g) + 12H2O(g) ΔH = +2220 kJ/mol
Finally, we need to multiply the water formation reaction by a factor and reverse it:
6H2(g) + 3O2(g) → 6H2O(g) ΔH = +858 kJ/mol
Now, we can add up the three manipulated reactions to obtain the desired reaction, which is the combustion of propene:
3CH2=CHCH3(g) + 15O2(g) → 9CO2(g) + 12H2O(g) ΔH = ?
By summing up the enthalpy changes of the three reactions, we get:
ΔH = (+124 kJ/mol) + (+2220 kJ/mol) + (-858 kJ/mol) = +1486 kJ/mol
However, this value corresponds to the enthalpy change for the combustion of three moles of propene. To find the enthalpy change for one mole of propene, we divide the value by three:
ΔH = +1486 kJ/mol ÷ 3 = +495.33 kJ/mol
Therefore, the standard enthalpy of combustion of propene is approximately -495.33 kJ/mol.
To learn more about Hess's Law click here, brainly.com/question/31508978
#SPJ11
Is it possible to prepare 2-bromopentane in high yield by halogenation of an alkane? How many monohalo isomers are possible upon radical halogenation of the parent alkane? (Consider stereoisomers as well.)
Yes, it is possible to prepare 2-bromopentane in high yield by halogenation of an alkane. In the presence of UV light or heat, free-radical halogenation of alkanes happens.
The reaction proceeds in three phases: chain initiation, chain propagation, and chain termination. The propagation phase generates several mono-haloalkanes as intermediates in the formation of polyhalogenated compounds that may have more than one halogen atom.
For example, suppose pentane (C5H12) is subjected to radical halogenation with bromine (Br2).
In that case, 2-bromopentane (C5H11Br) is produced as one of several potential products, depending on the reaction conditions (temperature, halogen concentration, and so on).It is predicted that radical halogenation of an alkane would produce a mixture of mono-haloalkanes. In the case of pentane, for example, it is possible to form 8 different monohalo isomers. In the case of 2-bromopentane, only one stereoisomer is possible. As a result, the maximum possible yield of 2-bromopentane is roughly 12.5% (1/8th of the total possible products).
To know more about bromopentane visit:
https://brainly.com/question/31942070
#SPJ11
Which statement accurately describes how scientists collect data?
A. The units used to record data are different depending on the country.
B. More complex devices are always better for collecting data.
c. The method used to collect data depends on the desired data.
d. Simple devices are always better for collecting data.
Answer:
C
Explanation:
PLEASE USE TRIAL AND ERROR / ITERATIVE METHOD IN SOLVING. THANK
YOU!
EXAMPLE 8-9 Effect of Flushing on Flow Rate from a Shower The bathroom plumbing of a building consists of 1.5-cm-diameter copper pipes with threaded connectors, as shown in Fig. 8-52. (a) If the gage
In order to solve the given problem with iterative method, follow these steps:
Step 1: Make an Initial Guess of the pressure drop
Let us assume an initial guess for the pressure drop of 15 kPa, this value will be used to calculate the Reynolds Number which will then be used to calculate the friction factor.
Step 2: Calculate Reynolds Number: The Reynolds number is calculated using the following formula:
Reynolds Number = (4 * Flowrate) / (π * Diameter * Viscosity)
For the given values, the Reynolds Number is calculated as:
Re = (4 × 0.034) / (π × 1.5 × 10^-3 × 8.9 × 10^-4) = 15367.23
Step 3: Calculate friction factor: The friction factor is calculated using the following formula:
f = (ΔP × Diameter) / (2 * ρ * V^2)
For the given values, the friction factor is calculated as:
f = (15 × 10^3 × 1.5 × 10^-2) / (2 × 8.9 × 10^3 × 2.32^2) = 0.0056
Step 4: Calculate the new value of pressure drop: The pressure drop is calculated using the Darcy-Weisbach formula:
ΔP = f * (Length / Diameter) * (ρ * V^2 / 2)
For the given values, the new value of pressure drop is:
ΔP = 0.0056 × (30 / 1.5) × (8.9 × 10^3 × 2.32^2 / 2) = 7.95 kPa
Step 5: Compare the new value of pressure drop with the initial guess. If the difference between the new value of pressure drop and the initial guess is greater than the specified tolerance, then repeat the above steps until the difference between the new value of pressure drop and the initial guess is within the specified tolerance.
Know more about iterative method here:
https://brainly.com/question/30311178
#SPJ11
With explainations please am not in hurry (45)
Using activities, find Ag+ in 0.05 M KSCN saturated with AgSCN Ksp for AgSCN = 1.1 *10-1²
The concentration of Ag+ ions in 0.05 M KSCN saturated with AgSCN is 1.05 × 10^-6 M.
The solubility product (Ksp) of AgSCN is 1.1 × 10^-12. In this activity, we'll use this knowledge to locate the Ag+ ion concentration in 0.05 M KSCN saturated with AgSCN.
KSCN dissociates into K+ and SCN-.
The reaction is: KSCN(aq) → K+(aq) + SCN-(aq)
The dissociation equation for AgSCN is: AgSCN(aq) ⇔ Ag+(aq) + SCN-(aq)
At equilibrium, [Ag+] and [SCN-] are the same, and we'll use x to represent both.
The initial concentration of KSCN was 0.05 M.
Let us first write the reaction for AgSCN dissociation: AgSCN(aq) ⇔ Ag+(aq) + SCN-(aq)
Let's suppose that the concentration of SCN- is x M, and the amount of Ag+ that is released is also x M. Then, the concentration of AgSCN at equilibrium would be (0.05 - x) M.
Ksp can be calculated using the equation Ksp = [Ag+][SCN-].
We can substitute the values obtained above.
Ksp = x * xKsp = x²Ksp = 1.1 × 10^-12M²
Solving the above equation gives us: x = √(Ksp)x = √(1.1 × 10^-12)x = 1.05 × 10^-6 mol/L
Know more about concentration here:
https://brainly.com/question/28327102
#SPJ11
How
does secondary steelmaking affect the final properties of strip
steel?
Secondary steelmaking plays a crucial role in the production of strip steel as it significantly influences the final properties of the steel. By employing various refining techniques, secondary steelmaking helps to adjust and enhance the composition and cleanliness of the steel.
Resulting in improved mechanical, chemical, and surface properties. The boundary layer thickness is not directly related to secondary steelmaking and thus is not applicable to this context. Secondary steelmaking refers to the refining process that follows primary steelmaking (e.g., basic oxygen furnace or electric arc furnace) and precedes the casting or rolling of the steel. It involves various operations such as ladle refining, degassing, desulfurization, alloying, and temperature adjustment.
During secondary steelmaking, the composition of the steel can be adjusted to achieve the desired chemical properties. Impurities, such as sulfur and phosphorus, can be reduced, and alloying elements can be added to enhance specific characteristics of the steel. This allows for greater control over the steel's mechanical properties, such as strength, hardness, and toughness.
Secondary steelmaking also plays a crucial role in improving the cleanliness of the steel. By employing processes like ladle metallurgy refining and vacuum degassing, non-metallic inclusions, such as oxides and sulfides, can be reduced or eliminated. Cleaner steel with lower inclusion content has improved surface quality, reduced defects, and enhanced corrosion resistance. The final properties of strip steel, including mechanical strength, ductility, formability, surface quality, and chemical composition, are significantly influenced by the secondary steelmaking processes. The adjustments made during secondary steelmaking ensure that the steel meets the required specifications and standards for its intended applications.
Regarding the boundary layer thickness, it is a concept related to fluid dynamics and is not directly applicable to the steelmaking process. The boundary layer thickness refers to the region near a solid surface where the velocity of the fluid changes due to viscous effects. It is a topic studied in fluid mechanics and typically applies to fluid flow over surfaces, such as in aerodynamics or heat transfer. It does not have a direct impact on the properties of strip steel during the secondary steelmaking process.
Learn more about viscous effects here:- brainly.com/question/889499
#SPJ11
The diagram below shows the different phase transitions that occur in matter.
0000
Solid
2345
Liquid
Gas
Which arrow would most likely represent the phase change that involves the same amount of energy as arrow 1?
02
6
The phase diagram represents the different phase transitions that occur in matter. The arrow labeled "1" represents the transition from a solid to a liquid state, which is commonly known as melting or fusion.
When a substance undergoes melting, it absorbs a specific amount of energy known as the latent heat of fusion. To identify the arrow that most likely represents a phase change involving the same amount of energy as arrow 1, we need to consider the specific phase transitions and their associated energy changes. The phase transition directly opposite to melting on the phase diagram is the transition from a liquid to a solid state, known as freezing or solidification. This transition involves the release of the same amount of energy that was absorbed during melting.
Hence, the arrow that most likely represents the phase change involving the same amount of energy as arrow 1 is arrow "6," which signifies the transition from a liquid to a solid state. Both melting and freezing involve the same amount of energy exchange, as they are reversible processes occurring at the same temperature.
For more questions on fusion, click on:
https://brainly.com/question/17870368
#SPJ8
20. You are producing a 35°API crude oil from a reservoir at 5,000 psia and 140°F. The bubble-point pressure of the reservoir liquids is 4,000 psia at 140°F. Gas with a gravity of 0.7 is produced with the oil at a rate of 900 scf/ STB. Calculate: a. Density of the oil at 5,000 psia and 140°F b. Total formation volume factor at 5,000 psia and 140°F
a. The density of the oil at 5,000 psia and 140°F is approximately 72.440 lb/ft³.
b. The total formation volume factor at 5,000 psia and 140°F is approximately 0.02827.
To calculate the density of the oil at 5,000 psia and 140°F, we can use the Standing's correlation for the oil density:
ρo = ρw + (1 - ρw) * (0.972 + 0.000147 * API * p)
where:
ρo is the density of the oil in lb/ft³,
ρw is the density of water at 60°F (since we don't have the specific gravity of the water at 140°F, we will assume it is the same as at 60°F, which is 62.4 lb/ft³),
API is the API gravity of the oil (35°API in this case),
p is the pressure in psia.
Using the given values, we can calculate the oil density:
ρo = 62.4 + (1 - 62.4) * (0.972 + 0.000147 * 35 * 5000)
ρo = 62.4 + (1 - 62.4) * (0.972 + 0.000147 * 175000)
ρo = 62.4 + (1 - 62.4) * (0.972 + 25.725)
ρo = 62.4 + (1 - 62.4) * 26.697
ρo = 62.4 + 0.376 * 26.697
ρo = 62.4 + 10.040
ρo = 72.440 lb/ft³
So, the density of the oil at 5,000 psia and 140°F is approximately 72.440 lb/ft³.
Now, let's calculate the total formation volume factor (FVF) at 5,000 psia and 140°F. We can use the Standing's correlation for the FVF:
Bo = Bg * (1 + c * (Rsb - Rs))
where:
Bo is the oil formation volume factor,
Bg is the gas formation volume factor,
c is the oil formation volume factor correction factor (assumed to be 0.00005 psi⁻¹ in this case),
Rsb is the solution gas-oil ratio at the bubble-point pressure (from the reservoir fluid properties table),
Rs is the actual solution gas-oil ratio.
To find the solution gas-oil ratio (Rs), we can use the following equation:
Rs = (Bg / Bo) * (P - Pb)
where:
P is the pressure (5,000 psia in this case),
Pb is the bubble-point pressure (4,000 psia in this case).
Using the given values and assuming Bg = 0.02827 (from the gas gravity), we can calculate the solution gas-oil ratio:
Rs = (0.02827 / Bo) * (5,000 - 4,000)
Rs = (0.02827 / Bo) * 1,000
Now, we need to find Rsb from the reservoir fluid properties table. Since we don't have that information, we'll assume Rsb = 100 scf/STB.
Rs = (0.02827 / Bo) * 1,000 = 100
Now, we can rearrange the equation to solve for Bo:
Bo = Bg / (1 + c * (Rsb - Rs))
Bo = 0.02827 / (1 + 0.00005 * (100 - Rs))
Bo = 0.02827 / (1 + 0.00005 * (100 - 100))
Bo = 0.02827 / (1 + 0.00005 * 0)
Bo = 0.02827 / (1 + 0)
Bo = 0.02827
So, the total formation volume factor (Bo) at 5,000 psia and 140°F is approximately 0.02827.
Learn more about Density here: brainly.com/question/14804049
#SPJ11