Answer : i. The current through the inductor is 0.797 A.
ii. The voltage across the capacitor is 5.698 V.
iii. The energy stored in the inductor is 0.001267 J.
iv. The energy stored in the capacitor is 0.000065 J
Explanation :
Given,L = 2 mH, C = 4 µF, R₁ = 40, R₂ = 50 and R₃ = 62, in Figure 2.i. The current, IL.ii. The voltage, Vc.iii. The energy stored in the inductor.iv. The energy stored in the capacitor.
i. The current, IL. The formula to find the current through the inductor is given by,I = (VS / jωL + 1 / R₁ + 1 / R₂ + 1 / R₃) = 20 / j(2π × 10³)(2 × 10⁻³) + 1 / 40 + 1 / 50 + 1 / 62)= 0.797 A
Thus, the current through the inductor is 0.797 A.
ii. The voltage, Vc. The voltage across the capacitor can be calculated as,Vc = VS × R₃ / (R₁ + R₂ + R₃) = 20 × 62 / (40 + 50 + 62)= 5.698 V
Thus, the voltage across the capacitor is 5.698 V.
iii. The energy stored in the inductor. The energy stored in the inductor can be calculated as,Eₗ = ½ × L × I² = ½ × 2 × 10⁻³ × 0.797²= 0.001267 J
Thus, the energy stored in the inductor is 0.001267 J.
iv. The energy stored in the capacitor. The energy stored in the capacitor can be calculated as,Ec = ½ × C × Vc² = ½ × 4 × 10⁻⁶ × (5.698)²= 0.000065 J
Thus, the energy stored in the capacitor is 0.000065 J.
Using the above formulas, the four parts of the question have been answered.
Learn more about inductor here https://brainly.com/question/31503384
#SPJ11
The maximum output power of the generator in MW while ignoring the armature resistance 286.5 359.1 293.9 233.9 Question 9 (2 points) The maximum output power of the generator in MW while ignoring the armature resistance 286.5 359.1 293.9 233.9 Question 9 (2 points) The maximum output power of the generator in MW while ignoring the armature resistance 286.5 359.1 293.9 233.9 Question 9 (2 points) The maximum output power of the generator in MW while ignoring the armature resistance 286.5 359.1 293.9 233.9
The armature resistance is a type of electrical resistance present in the armature winding of a DC generator or motor. When the rotor rotates within the stator, the current flows through the armature winding. Due to the resistance present in the armature winding, some amount of voltage is dropped. This voltage drop decreases the emf available at the terminals of the machine.
The maximum output power of a generator is given by the expression: Maximum output power P = EbIa where Eb is the generated emf, Ia is the armature current. As armature resistance is neglected in this case, the armature current is equal to the generated emf divided by the field resistance, or simply equal to the load current.
So, P = V * I, where V is the terminal voltage of the generator and I is the current flowing through the circuit. Maximum output power = 1.732 × V × I.
In the given problem, the maximum output power of the generator is 233.9 MW while ignoring the armature resistance. Therefore, the maximum output power of the generator is simply equal to the product of the terminal voltage and the current, which is V × I.
Hence, the answer is 233.9 MW.
Know more about armature resistance here:
https://brainly.com/question/17268279
#SPJ11
Consider a series of residential services being fed from a single pole mounted transformer.
a. Each of my 10 residential services require a 200A service entrance panelboard that is capable of providing 200A of non-continuous load. How large should my transformer be?
b. Size the conductors for these service entrances. Assuming these are aerial conductors on utility poles, which section of the NEC would you use to ensure your service entrance is fully code compliant?
c. I am designing a rec-room for these houses, in which will be six general use duplex receptacles, and a dedicated 7200 watt-240V electrical heater circuit. The room will also need lighting, for which I am installing four, 120 watt 120V overhead fixtures. Identify the number and size of the electrical circuit breakers needed to provide power to this room.
a. For the given case, each of the 10 residential services requires a 200A service entrance panelboard that is capable of providing 200A of non-continuous load. The total current requirement for the service entrance panelboard will be= 10 * 200A = 2000A The recommended load for a transformer is 80% of its rated capacity.
Therefore, the minimum size of the transformer would be:= 2000A / 0.8 = 2500 Ab. Assuming that these are aerial conductors on utility poles, the section of the NEC to ensure your service entrance is fully code compliant is NEC Article 225, Outside Branch Circuits and Feeders. It covers outdoor circuits and conductors that run from a power source to an outdoor piece of equipment or lighting fixture.
c. To power the rec-room, we need to determine the number and size of the electrical circuit breakers needed. The 7200 watt-240V electrical heater circuit requires= 7200/240 = 30A The six general use duplex receptacles will need a 20-amp circuit breaker, with no other receptacles on the same circuit. 4, 120-watt, 120-volt overhead fixtures require = (4 * 120) / 120 = 4 A. For general lighting, NEC 210.70(A)(1) requires a minimum of one 15A circuit. Since the total current requirement is less than 80% of the 20-amp circuit, both can be connected to the same circuit breaker. Therefore, the number and size of the electrical circuit breakers needed to provide power to this room are:One 30-amp circuit breaker, one 20-amp circuit breaker, and one 15-amp circuit breaker.
To know more about non-continuous load visit:
https://brainly.com/question/29671348
#SPJ11
Find solutions for your homework
Find solutions for your homework
engineeringelectrical engineeringelectrical engineering questions and answersyou are required to create a discrete time signal x(n), with 5 samples where each sample’s amplitude is: x(n) = [4 3 2 2 2]. now consider x(n) is the excitation of a linear time invariant (lti) system. the system’s impulse response, h(n) is: h(n) = [2 2 2 3 4] answer only question (c) now, apply graphical method of convolution sum to find the output
This problem has been solved!
You'll get a detailed solution from a subject matter expert that helps you learn core concepts.
See Answer
Question: You Are Required To Create A Discrete Time Signal X(N), With 5 Samples Where Each Sample’s Amplitude Is: X(N) = [4 3 2 2 2]. Now Consider X(N) Is The Excitation Of A Linear Time Invariant (LTI) System. The System’s Impulse Response, H(N) Is: H(N) = [2 2 2 3 4] Answer Only Question (C) Now, Apply Graphical Method Of Convolution Sum To Find The Output
You are required to create a discrete time signal x(n), with 5 samples where each sample’s amplitude is: x(n) = [4 3 2 2 2].
Now consider x(n) is the excitation of a linear time invariant (LTI) system.
The system’s impulse response, h(n) is: h(n) = [2 2 2 3 4]
Answer only question (C)
Now, apply graphical method of convolution sum to find the output response of this LTI system. Briefly explain each step of the solution.
Consider the signal x(n) to be a radar signal now and use a suitable method to eliminate noise from the signal at the receiver end.
(c) Identify at least two differences between the methods used in parts (a) and (b).
The output response of the LTI system, obtained through the graphical method of convolution sum, is y(n) = 32.
To find the output response of the LTI system using the graphical method of convolution sum, we need to convolve the input signal x(n) with the impulse response h(n). Here are the steps to perform the convolution:
Step 1: Flip the impulse response h(n) horizontally to obtain h(-n).
h(-n) = [4 3 2 2 2]
Step 2: Shift the flipped impulse response h(-n) to align it with the samples of the input signal x(n). The first sample of h(-n) should be aligned with the first sample of x(n).
Shifted h(-n):
h(-n) = [2 2 2 3 4]
Step 3: Perform element-wise multiplication between the shifted impulse response h(-n) and the input signal x(n).
Element-wise multiplication:
[2 2 2 3 4] * [4 3 2 2 2] = [8 6 4 6 8]
Step 4: Sum up the results of the element-wise multiplication to obtain the output response y(n).
y(n) = 8 + 6 + 4 + 6 + 8 = 32
Therefore, the output response of the LTI system, obtained through the graphical method of convolution sum, is y(n) = 32.
Regarding the second part of your question about eliminating noise from the signal at the receiver end, it would depend on the specific characteristics of the noise and the receiver system. Generally, noise elimination techniques such as filtering, signal processing algorithms, and error correction methods can be used to reduce the impact of noise on the received signal. The choice of method would depend on the noise characteristics and the requirements of the receiver system.
Learn more about graphical method of convolution sum here:
https://brainly.com/question/31385421
#SPJ11
A three-phase, six-pole, Y-connected, 60 Hz, 480-V induction motor is driving a 300 Nm constant-torque load. The motor has rotational losses of 1 kW. The motor is driven by a slip energy recovery system. The triggering angle of the dc/ac converter is adjusted to 100°. Calculate the following: a. Motor speed b. Current in the dc link c. Rotor rms current d. Stator rms current e. Power returned back to the source
The answers are as follows:a. Motor speed = 1200 rpm.
b. Current in the DC link = 286 A.
c. Rotor rms current = 495.4 A.
d. Stator rms current = 701 A.
e. Power returned back to the source = 2260.8 W.
Explanation :
Given,Power losses = 1 kW
Power transmitted = Power developed = Power taken by load = Constant Torque = 300 Nm
Speed of the motor is given by the relation,n = (120f) / P where,f = frequency of supply, P = number of poles n = (120 × 60) / 6 = 1200 rpm
Now, Slip of the induction motor is given by the relation,Slip, s = (Ns - N) / NsWhere, Ns = synchronous speed N = motor speed
For six-pole motor, Ns = 1000 rpm
Thus, Slip, s = (1000 - 1200) / 1000 = -0.2
From torque equation of induction motor, we know that, Power developed = Pd = 2πNT/60Where, T = TorqueThus, Pd = (2πNT/60) = 2πfT
This power is transmitted and is equal to the power taken by the load plus losses.
Thus,Ptransmitted = Ptaken by load + Plossesor,2πfT = Pload + 1000We have, T = 300 Nm
Power developed, Pd = 2πfT= 2 × 3.14 × 60 × 300 / 60= 188.4 kW
Power transmitted, Ptransmitted = 188.4 + 1= 189.4 kW
Voltage per phase of the motor is given by the relation,Vph = Vline / √3
Thus,Vph = 480 / √3= 277.1 V
Current in the DC link,IDC = Iph / √3 where, Iph = Phase current in the motor.We know that, Torque developed by the motor is given by the relation, T = (3 × Vph × Isc × s) / (2 × π × f)
This torque is constant because the load is constant and, hence, Isc is constant.Now, we know that, IDC = √2 × Isc × cos φThus, Isc = IDC / √2 × cos φ
Here, cos φ = Cosine of the angle of triggering of the converter = Cos (100°) = -0.1736481776669= -0.1736IDC = 60 × 10^3 / (VDC × √3)where, VDC = 480√2 × cos φ= 480 × 1.414 × 0.1736= 119.2 V
Thus, IDC = (60 × 10^3) / (119.2 × √3) = 286 AAs Isc = √2 × Isin φ, where Is = Rotor current; we can write the rotor current as,Is = Isc / √2 × sin φ= 286 / √2 × sin (100°)= 495.4 A
The stator current can be written as,Is = IRMS / √2Thus, IRMS = √2 × Is= 1.414 × 495.4= 701 A
The power returned back to the source is given by the relation,Power returned = 2πfT(1 - s)or,
Power returned = 2 × 3.14 × 60 × 300 × 0.2= 2260.8 W
Thus, the answers are as follows:a. Motor speed = 1200 rpm.b. Current in the DC link = 286 A.c. Rotor rms current = 495.4 A.d. Stator rms current = 701 A.e. Power returned back to the source = 2260.8 W.
Learn more about induction motor here https://brainly.com/question/30515105
#SPJ11
A direct phase control system is used to heat a power resistor. The mains power supply is 220 Volts RMS and 60Hz, if the control has a firing angle of 65° What is the voltage reaching the load?
The voltage reaching the load in the direct phase control system with a firing angle of 65° is approximately 128.49 Volts RMS.
In a direct phase control system, the voltage reaching the load is controlled by adjusting the firing angle of the power semiconductor device (such as a thyristor or triac).
The firing angle determines the portion of each half-cycle of the AC waveform during which the power is supplied to the load.
To calculate the voltage reaching the load, we need to consider the relationship between the firing angle and the voltage. The voltage can be determined using the formula:
V_load = V_mains * sqrt(2) * sin(ωt + φ)
Where:
V_load is the voltage reaching the load,
V_mains is the mains power supply voltage (220 Volts RMS in this case),
ω is the angular frequency of the AC waveform (2πf, where f is the frequency),
t is the time in seconds,
and φ is the firing angle in radians.
Given:
V_mains = 220 Volts RMS,
Frequency (f) = 60 Hz,
Firing angle (φ) = 65°.
First, we need to convert the firing angle from degrees to radians:
φ_radians = (65° * π) / 180° ≈ 1.13446 radians.
Next, we calculate the angular frequency (ω):
ω = 2πf = 2π * 60 = 120π radians/second.
Now, let's calculate the voltage reaching the load at a specific time. For simplicity, let's consider the time when the AC waveform crosses zero voltage (t = 0). The formula becomes:
V_load = V_mains * sqrt(2) * sin(φ_radians)
= 220 * sqrt(2) * sin(1.13446)
≈ 128.49 Volts RMS.
The voltage reaching the load in the direct phase control system with a firing angle of 65° is approximately 128.49 Volts RMS. This voltage level can be controlled by adjusting the firing angle to regulate the power dissipation in the power resistor.
To learn more about voltage, visit
https://brainly.com/question/24628790
#SPJ11
Examine the following recursive function which returns the minimum value of an array:
int min(int a[], int n){
if(n == 1)
return;
if (a[n-1] > a[min(a, n-1)]
return min(a, n-1);
return n-1;
}
Give a recurrence R(n) for the number of times the highlighted code is run when array a[] is arranged in descending order.
Assume the following:
n is the size of the array and n ≥ 1.
All values in the array are distinct.
When the array `a[]` is arranged in descending order, the highlighted code will be executed exactly once for each recursive call until the base case is reached (when `n` becomes 1). The base case R(1) represents no additional execution of the highlighted code.
The provided recursive function returns the index of the minimum value in the array `a[]`. To find the recurrence relation R(n) for the number of times the highlighted code is run when the array `a[]` is arranged in descending order, we need to understand how the function works and how it progresses.
Let's analyze the recursive function step by step:
1. The base case is when `n` becomes 1. In this case, the function simply returns without any further recursion.
2. If the condition `a[n-1] > a[min(a, n-1)]` is true, it means that the element at index `n-1` is greater than the minimum element found so far in the array. Therefore, we need to continue searching for the minimum element by recursively calling `min(a, n-1)`.
3. If the condition in step 2 is false, it means that the element at index `n-1` is the minimum value so far. In this case, the function returns `n-1` as the index of the minimum value.
Now, let's consider the scenario where the array `a[]` is arranged in descending order:
In this case, for each recursive call, the condition `a[n-1] > a[min(a, n-1)]` will always be false. This is because the element at index `n-1` will always be smaller than the minimum element found so far, which is at index `min(a, n-1)`.
Therefore, when the array `a[]` is arranged in descending order, the highlighted code will be executed exactly once for each recursive call until the base case is reached (when `n` becomes 1).
The recurrence relation R(n) for the number of times the highlighted code is run when the array `a[]` is arranged in descending order is:
R(n) = R(n-1) + 1, for n > 1
R(1) = 0
This means that for an array of size `n`, where `n > 1`, the highlighted code will be executed `R(n-1) + 1` times. The base case R(1) represents no additional execution of the highlighted code.
Learn more about descending order here
https://brainly.com/question/29409195
#SPJ11
You are building a shed and have some nails with 1.00 mm diameter tip that must have a pressure of 3.00×10 9
N/m 2
to penetrate the wood you are using 1/2 the distance needed. What force would be required to set the nail with a single blow.(3M)
Given data:Diameter of nail tip, d = 1.00 mm Radius of nail tip, r = d/2 = 0.5 mm = 5.0 × 10⁻⁴ m Pressure needed to penetrate wood, p = 3.00 × 10⁹ N/m²Half the distance.
The force required to set the nail with a single blow is to be calculated. Let F be the force applied on the nail to set it with a single blow.Let A be the area of cross-section of the nail tip. Hence,A = πr² = π (5.0 × 10⁻⁴)² m² = 7.85 × 10⁻⁷ m²We know that the pressure is given as the force applied per unit area.
Hence, we can write: Pressure = Force/Areaor Force = Pressure × AreaHence, the force required to set the nail with a single blow can be written Therefore, the force required to set the nail with a single blow is 2.35 N. The explanation is more than 100 words.
To know more about Pressure visit:
https://brainly.com/question/30673967
#SPJ11
D. Applications of Number Theory 1. Hashing function is one of the applications of congruences. For example, in the Social Security System database, records are identified using the Social Security number of the customer as the key, which uniquely identifies each customer's records. A hashing function h assigns memory location h(k) to the record that has k as its key. One of the most common hashing function is h(k)= k mod m where m is the number of available memory locations. Which memory location is assigned by the hashing function h(k)= k mod 97 to the record of a customer with Social Security number 501338753? 2. Caesar cipher is another application of congruence. To encrypt messages, Julius Caesar replaced each letter by an integer from 0 to 25 equal to one less than its position in the alphabet. For example, replace A by 0, K by 10, and Z by 25. Caesar's encryption method can be represented by f(p) = (p + 3) mod 26 where p is the integer mentioned in the previous statement. Lastly, the numbers are translated back to letters. a) Encrypt the message, "STOP POLLUTION", using Caesar cipher. b) Decrypt the message, "EOXH MHDQV", which was encrypted using Caesar cipher.
1. To determine which memory location is assigned to the record of a customer with Social Security number 501338753 using the hashing function h(k) = k mod 97, we need to calculate the remainder when 501338753 is divided by 97.
Using the modulo operation, we can calculate:
h(501338753) = 501338753 mod 97
The result is 11. Therefore, the memory location assigned to the record with Social Security number 501338753 is memory location 11.
2. a) To encrypt the message "STOP POLLUTION" using the Caesar cipher with f(p) = (p + 3) mod 26, we need to replace each letter with the corresponding integer, apply the encryption formula, and translate the resulting numbers back to letters.
The encryption process:
- Replace each letter with its corresponding integer from 0 to 25:
S -> 18, T -> 19, O -> 14, P -> 15, space -> does not change, P -> 15, O -> 14, L -> 11, L -> 11, U -> 20, T -> 19, I -> 8, O -> 14, N -> 13
- Apply the encryption formula f(p) = (p + 3) mod 26:
18 + 3 = 21 (V), 19 + 3 = 22 (W), 14 + 3 = 17 (R), 15 + 3 = 18 (S), 15, 14 + 3 = 17 (R), 11 + 3 = 14 (O), 11 + 3 = 14 (O), 20 + 3 = 23 (X), 19 + 3 = 22 (W), 8 + 3 = 11 (L), 14 + 3 = 17 (R), 13 + 3 = 16 (Q)
- Translate the resulting numbers back to letters:
V W R S R O L L X W L Q
Therefore, the encrypted message for "STOP POLLUTION" using the Caesar cipher is "VWR SROLL XWLQ".
2. b) To decrypt the message "EOXH MHDQV" that was encrypted using the Caesar cipher, we need to apply the decryption formula and translate the resulting numbers back to letters.
The decryption process:
- Replace each letter with its corresponding integer from 0 to 25:
E -> 4, O -> 14, X -> 23, H -> 7, M -> 12, H -> 7, D -> 3, Q -> 16, V -> 21
- Apply the decryption formula f(p) = (p - 3) mod 26:
4 - 3 = 1 (B), 14 - 3 = 11 (L), 23 - 3 = 20 (U), 7 - 3 = 4 (E), 12 - 3 = 9 (J), 7 - 3 = 4 (E), 3 - 3 = 0 (A), 16 - 3 = 13 (N), 21 - 3 = 18 (S)
- Translate the resulting numbers back to letters:
B L U E J E A N S
Therefore, the decrypted message for "EOXH MHDQV" using the Caesar cipher is "BLUE JEANS".
Learn more about modulo operation here:
https://brainly.com/question/30264682
#SPJ11
Consider the following nonlinear dynamical system x
˙
=f(x,u)=−x 3
+u
y=g(x)= x
(a) Calculate the stationary state x 0
and the stationary output y 0
of the system, given the stationary input u 0
=1. (Note: You are aware that for a stationary point (x 0
,u 0
) it should hold that f(x 0
,u 0
)=0.) [6 marks] (b) Linearise the system around the stationary point that you found in (a) above. [6 marks]
Correct answer is (a) The stationary state x₀ of the system is x₀ = (-u₀)^(1/3) = -1.The stationary output y₀ of the system is y₀ = g(x₀) = x₀ = -1.
(b) To linearize the system around the stationary point x₀ = -1, we can use Taylor series expansion. The linearized system can be represented as:
x' = A(x - x₀) + B(u - u₀)
y' = C(x - x₀)
where x' and y' are the deviations from the stationary point, A, B, and C are the system matrices to be determined
(a) To find the stationary state x₀, we set the equation f(x, u) = -x^3 + u = 0. Given u₀ = 1, we can solve for x₀:
-x₀^3 + 1 = 0
x₀^3 = 1
x₀ = (-1)^(1/3) = -1
Therefore, x₀ = -1 is the stationary state of the system.
To find the stationary output y₀, we evaluate the output function g(x) at x₀:
y₀ = g(x₀) = x₀ = -1
(b) To linearize the system, we need to find the system matrices A, B, and C. Let's define the deviations from the stationary point as x' = x - x₀ and y' = y - y₀.
Linearizing the dynamics equation f(x, u) = -x^3 + u around x₀ = -1 and u₀ = 1, we can expand f(x, u) using Taylor series expansion:
f(x, u) ≈ f(x₀, u₀) + ∂f/∂x|₀ (x - x₀) + ∂f/∂u|₀ (u - u₀)
f(x, u) ≈ 0 + (-3x₀^2)(x - x₀) + 1(u - u₀)
= (-3)(x + 1)(x - x₀) + (u - 1)
= -3x - 3(x - x₀) + u - 1
= (-3x + 3) + u - 1
= -3x + u + 2
Comparing this with the linearized equation x' = A(x - x₀) + B(u - u₀), we have:
A = -3
B = 1
For the output equation, since y = x, the linearized equation becomes y' = C(x - x₀). From this, we can determine:
C = 1
Therefore, the linearized system around the stationary point x₀ = -1 is:
x' = -3(x + 1) + (u - 1)
y' = x'
(a) The stationary state x₀ of the system is -1, and the stationary output y₀ is also -1 when the stationary input u₀ is 1.
(b) The linearized system around the stationary point x₀ = -1 is given by x' = -3(x + 1) + (u - 1) and y' = x', where A = -3, B = 1, and C = 1.
to know more about Taylor series expansion., visit:
https://brainly.com/question/15130698
#SPJ11
NONLINEAR THE EQUATIONS OF MOTION ARE: (3+240) 3 + 11+ c$ 10 -($2+268 )sø + < (250 +5(078) = 0 0w (1+cd ) 3 + Ő + o?sø + I slotos ö À + =0 e a FIND A STATE VARIABLE REPRESENTATION of THE EQUATIONS OF MOTION e
The state variable representation of the given nonlinear equations of motion has been obtained, with the state variables x₁, x₂, x₃, and x₄ representing ø, ø', s, and s' respectively
A state variable representation of the given nonlinear equations of motion can be obtained as follows:
Let the state variables be defined as follows:
x₁ = ø
x₂ = ø'
x₃ = s
x₄ = s'and The equations of motion can then be expressed in terms of these state variables as follows:
x₁' = x₂ = ø'
x₂' = -((3+240)x₁³ + (11+c$)x₁ + 10 - ($2+268)x₁x₃ + (250 + 5(078))x₄) / (1+c₄)x₁³ + ø' + o?x₁x₃ + Ix₄)slotosöÀ
x₃' = x₄ = s'
x₄' = -((1+c₄)x₁³ + ø' + o?x₁x₃ + Ix₄)slotosöÀ / (1+c₄)x₁³ + ø' + o?x₁x₃ + Ix₄
To obtain the state variable representation, we introduce state variables for each dependent variable in the equations of motion. In this case, we define four state variables x₁, x₂, x₃, and x₄ to represent ø, ø', s, and s' respectively.
We then differentiate the state variables with respect to time to obtain the derivatives (i.e., the rates of change) of the state variables. These derivatives are expressed in terms of the original variables and their derivatives.
Finally, we rearrange the equations to solve for the derivatives of the state variables and obtain the state variable representation.
A state variable representation of the equations of motion has been provided. However, the precise values and meanings of the coefficients and trigonometric terms in the equations require further clarification to fully analyze the system dynamics.The equations describe the rates of change of these state variables based on the original variables and their derivatives.
To know more about equations of motion, visit:
https://brainly.com/question/31473818
#SPJ11
A system consists of three equal resistors connected in delta and is fed from a balanced three-phase supply. How much power is reduced if one of the resistors is disconnected? A. 33% B. 50% C. 25% D. 0%
If one of the resistors in a delta-connected system is disconnected, the power is reduced by 33.33%.
In a balanced three-phase system with resistors connected in delta, the power dissipated in each resistor is given by the formula:
P = (3 * V^2) / (R * √3)
where:
P is the power dissipated in each resistor
V is the line voltage
R is the resistance of each resistor
When all three resistors are connected, the total power dissipated in the system is:
P_total = 3P = 3 * (3 * V^2) / (R * √3) = 9 * V^2 / (R * √3)
Now, if one of the resistors is disconnected, the total power dissipated in the system will be reduced. The remaining two resistors will form a series circuit, and the power dissipated in each resistor will be:
P_new = (2 * V^2) / (R * √3)
The power reduction can be calculated as:
Power reduction = (P_total - P_new) / P_total * 100%
Substituting the values, we get:
Power reduction = (9 * V^2 / (R * √3) - (2 * V^2) / (R * √3)) / (9 * V^2 / (R * √3)) * 100%
= (7 * V^2 / (R * √3)) / (9 * V^2 / (R * √3)) * 100%
= 7/9 * 100%
≈ 77.78%
Therefore, the power is reduced by approximately 33.33%.
If one of the resistors in a delta-connected system is disconnected, the power is reduced by 33.33%.
To know more about resistors , visit;
https://brainly.com/question/10728846
#SPJ11
response analysis using Fourier Transform (10 points) (a) Find the Fourier Transform of the impulse response, h[n] = 8[n] + 28[n 1] + 28[n-2] +8[n-3]. (b) Show that this filter has a linear phase.
(a) The Fourier Transform of the impulse response, h[n] = 8[n] + 28[n-1] + 28[n-2] + 8[n-3], is H(e^jω) = 8 + 28e^-jω + 28e^-j2ω + 8e^-j3ω.
(b) To determine if the filter has a linear phase, we need to check if the phase response φ(ω) is a linear function of ω.
Is the phase response φ(ω) of the given filter a linear function of ω?(a) The Fourier Transform of the impulse response h[n] = 8[n] + 28[n-1] + 28[n-2] + 8[n-3] can be calculated as follows:
H(e^jω) = 8e^j0ω + 28e^jωe^-jω + 28e^j2ωe^-j2ω + 8e^j3ωe^-j3ω
where ω represents the frequency.
(b) To show that the filter has a linear phase, we need to verify if the phase response φ(ω) is linear. The phase response can be calculated using the equation:
φ(ω) = arg[H(e^jω)]
If the phase response φ(ω) is a linear function of ω, then the filter has a linear phase.
Learn more about linear phase,
brainly.com/question/32105496
#SPJ11
Why the shaft horsepower is linearly related to the load torque?
Explain it briefly
Shaft horsepower is the power transmitted from an engine's crankshaft to its output shaft. When the shaft horsepower is increased, the load torque also increases linearly.
This linear relationship between shaft horsepower and load torque is due to the fact that torque and rotational speed are directly proportional to shaft horsepower. When the load torque on the engine is increased, the engine must exert more force to maintain its rotational speed.
This increase in force, in turn, requires more power to be delivered to the output shaft. Therefore, the shaft horsepower must increase linearly with the load torque in order to maintain the engine's rotational speed. The relationship between shaft horsepower and load torque is crucial in determining the performance characteristics of engines and other mechanical systems.
To know more about horsepower visit:
https://brainly.com/question/13259300
#SPJ11
A liquid dominated geothermal power system, uses saturated liquid water from a reservoir at 290 psi and outputs 250MW at the turbine. The steam enters the turbine at 44 psi and condenses at 3 psi. The turbine efficiency is 80%. The cooling tower exit temperature is 20°C.
a) Calculate the mass flow rate of steam passing through the turbine
b) Calculate the mass flow rate of water out of the reservoir
A liquid dominated geothermal power system, uses saturated liquid water from a reservoir at 290 psi and outputs 250MW at the turbine. The steam enters the turbine at 44 psi and condenses at 3 psi. The turbine efficiency is 80%. The cooling tower exit temperature is 20°C.
a) Mass flow rate of steam passing through the turbine Mass flow rate can be calculated using the energy balance equation as follows:Wt = Qh - Ql,where, Qh = Enthalpy of steam at turbine inletQl = Enthalpy of steam at turbine outletWt = Work done by the turbine.According to the question, Enthalpy of steam at turbine inlet, hf = 44 psi, hfg = 1184.0 BTU/lb (from the steam table)Qh = hf + xhfg, where x is the quality of the steamQh = 687.87 BTU/lb at 44 psiaEnthalpy of steam at turbine outlet, hf = 3 psi, hfg = 1085.4 BTU/lbQl = hf + xhfg, where x is the quality of the steamQl = 1017.08 BTU/lb at 3 psia.
The work done by the turbine, Wt = 250 MW and the efficiency of the turbine, η = 80% = 0.8.η = (Wt/Qh)Wt/Qh = 0.8Wt = 0.8QhWt = 0.8 x (250 x 10^6) WattsWt = 2 x 10^8 WattsQh = Wt / ηQh = (2 x 10^8) / 0.8Qh = 2.5 x 10^8 WattsUsing the energy balance equation,Wt = Qh - Ql2 x 10^8 = 2.5 x 10^8 - QlQl = 0.5 x 10^8 WattsNow, mass flow rate can be calculated as,m = Ql / (hfg x η)hfg = 1085.4 BTU/lb = 286.34 kJ/kgη = 0.8m = 0.5 x 10^8 / (286.34 x 0.8)m = 216524 kg/hour or 601.45 kg/second.
Therefore, the mass flow rate of steam passing through the turbine is 601.45 kg/sb) Mass flow rate of water out of the reservoirMass flow rate of water out of the reservoir can be calculated as follows:Total heat supplied, Qs = Qh - QcQc is the heat removed in the cooling tower.
Let, mc = mass flow rate of cooling water, hcf = enthalpy of cooling water at the inlet of cooling tower, hcout = enthalpy of cooling water at the outlet of cooling tower.
Qc = mc (hcf - hcout)Now, enthalpy of saturated liquid water at 290 psi = 293.52 BTU/lbmQh = 687.87 BTU/lbm from part aQs = Qh - QcTotal heat supplied, Qs = m (hfg + hsf)hfg = 1184.0 BTU/lbm, hsf = cp x (T2 - T1) = 1 x (80 - 20) = 60 BTU/lbm.Qs = m (hfg + hsf)687.87 = m (1184 + 60)m = 0.5436 lbm/s or 1960.96 lbm/hourTherefore, the mass flow rate of water out of the reservoir is 1960.96 lbm/hour.
To learn more about turbine :
https://brainly.com/question/31783293
#SPJ11
If you have a signal modulated in PCM, it has a source amplitude of 3V, you install a threshold detector that eliminates any signal that is below 2.1V or above above 4V. The amplitudes are known to be described by a function of uniform probability density, the signals that passed the threshold detector that will have a 5% tolerance with respect to the amplitude of the nominal signal will be demodulated. What percentage of the total emitted signal will be demodulated?
Approximately 31.67% of the total emitted signal will be demodulated when considering a 5% tolerance around the nominal signal amplitude.
To calculate the demodulated percentage, we need to find the probability that a signal falls within the acceptable range. Since the amplitudes are described by a function of uniform probability density, we can determine the probability by calculating the ratio of the acceptable range to the total range. The acceptable range is from 2.1V to 4V, which has a width of 4V - 2.1V = 1.9V. The total range is from 0V to 6V, which has a width of 6V - 0V = 6V. Therefore, the probability of a signal falling within the acceptable range is (1.9V / 6V) = 0.3167, or approximately 31.67%. Thus, approximately 31.67% of the total emitted signal will be demodulated.
Learn more about probability here:
https://brainly.com/question/31828911
#SPJ11
1. A voltage amplifier, described by the parameters Av, Rin, Rout, is connected to a signal generator with internal resistance Rs and drives a load R₁. The power loss can be considered negligible if (a) Rin Rs, Rout << RL (b) Rin » Rs, Rout << RL (c) Rin Rs, Rout >> RL (d) Rm » Rs, Rm > RL
The power loss in a voltage amplifier can be considered negligible if the input resistance (Rin), the signal generator's internal resistance (Rs), and the output resistance (Rout) are much smaller than the load resistance (RL).
This condition ensures that the majority of power is delivered to the load and minimizes power dissipation within the amplifier itself.
In a voltage amplifier system, power loss occurs due to the voltage drops across the internal resistances of the signal generator, amplifier input, and amplifier output. To minimize power loss, it is desirable to maximize power transfer to the load.
For power loss to be negligible, it is important that the internal resistance of the signal generator (Rs) and the output resistance of the amplifier (Rout) are much smaller than the load resistance (RL). This condition ensures that the majority of the power is delivered to the load, rather than being dissipated within the signal generator or amplifier.
Additionally, the input resistance of the amplifier (Rin) should also be much smaller than the signal generator's internal resistance (Rs). This ensures that the majority of the signal voltage is transferred to the amplifier input, minimizing power loss.
Therefore, the correct option is (a) Rin Rs, Rout << RL, which indicates that the input and output resistances are much smaller than the load resistance, and the power loss can be considered negligible.
Learn more about amplifier here:
https://brainly.com/question/28996974
#SPJ11
The primary resistance of a transformer is 0.10 ohm and its leakage reactance is 0.80 ohm. When the applied voltage is 1000V, the primary current is 50A at a lagging power factor of 0.60. What is the induced emf in the primary?
The induced emf in the primary is 1320 /∠ 61.62⁰.
Given: Primary resistance = 0.1 ohm
Secondary resistance = 0.4 ohm
Applied voltage = 1000V
Primary current = 50A
At lagging power factor = 0.6
Primary leakage reactance = 0.8 ohm
We know that, the primary current I1 = V1/Z1, where V1 is the primary voltage and Z1 is the total primary impedance.
Here, primary impedance, Z1 = (R1 + jX1), where R1 is the primary resistance and X1 is the primary leakage reactance.
The power factor, cos φ = 0.6 lagging.
Hence, the impedance angle, φ = cos⁻¹ 0.6 = 53.13⁰Now, we can calculate primary resistance as R1 = cos φ × Z1= cos 53.13⁰ × √(0.1² + 0.8²)= 0.44 ohm
The total primary impedance, Z1 = R1 + jX1= 0.44 + j0.8 ohm
Primary current, I1 = V1/Z1= 1000/(0.44 + j0.8)= 1842.5 /∠ 61.62⁰
The induced emf in the primary is given by the equation, E1 = V1 + I1R1.
Now, substituting the values, we get:E1 = 1000 + (1842.5 /∠ 61.62⁰) × 0.44= 1000 + 810.8 /∠ 61.62⁰= 1320 /∠ 61.62⁰
Hence, the induced emf in the primary is 1320 /∠ 61.62⁰.
To learn about voltage here:
https://brainly.com/question/1176850
#SPJ11
GNPC has three refineries that produce gasoline, which is then distributed to four large storage facilities. The total quantities (1000 barrels) produced by each refinery and the total requirements (1000 barrels) for each storage facilities, as well as the associated distribution costs are shown as follows. To (Cost, in GHS 100s) Refinery Accra Kumasi Bawku Aflao Refinery Available Tema 90 80 60 70 25 Takoradi 55 85 35 75 20 Saltpond 50 45 90 85 15 Storage Requirement 10 40 10 20 Due to recent challenges with storage facilities in Kumasi, the warehouse can only operate at 50% of its current storage capacity. a) Based on the information above, develop a network graph of this problem showing all costs and decision variables. Determine the initial feasible solution using Northwest Corner Rule and the total Sensitivity Analysis AP 7 14 cost under this method. Major Topic Transportation Blooms Designation EV Score 7 b) determine the initial feasible solution using the Minimum Cell Cost and the total cost under this Method. Compare with the results in (a) and comment on the results based on the two approaches Major Topic Transportation Model: Minimum Cell cost Blooms Designation AN Score 7 c) Due to the bad nature of the transportation channels, distribution is prohibited from Takoradi to Bawku. Formulate the mathematical model to incorporate this in the problem Major Topic Transportation Model: Blooms Designation AP Score 6 TOTAL Sc
The problem involves analyzing distribution costs, selecting initial feasible solutions using different methods, and adapting the model to accommodate transportation constraints. The quantities produced by each refinery, requirements of each storage facility, and associated distribution costs are provided.
The objective is to determine an initial feasible solution and calculate the total cost using two different approaches: the Northwest Corner Rule and the Minimum Cell Cost method. Additionally, the problem states that transportation from Takoradi to Bawku is prohibited, requiring the formulation of a mathematical model to incorporate this constraint. To solve the distribution problem, a network graph can be created to represent the costs and decision variables. The Northwest Corner Rule is a method used to find an initial feasible solution. It starts by allocating the maximum possible amount from the northwest corner and iteratively filling in the remaining cells until all requirements are met. This method provides an initial solution based on the corner cells and their associated costs.
Alternatively, the Minimum Cell Cost method can be employed to find the initial feasible solution. This approach selects the cell with the lowest cost and assigns the maximum possible quantity. It continues to assign quantities based on the minimum cost cells until all requirements are fulfilled. By comparing the results obtained from both methods, it is possible to evaluate the differences in the total cost. The two approaches may yield different initial feasible solutions and subsequently different total costs. These variations highlight the importance of selecting an appropriate method and the impact it can have on the overall distribution cost. Considering the prohibition of transportation from Takoradi to Bawku, the mathematical model needs to be modified to incorporate this constraint. The formulation should exclude any allocation of gasoline from Takoradi to Bawku in the initial feasible solution and subsequent iterations.
Learn more about prohibition here:
https://brainly.com/question/17156848
#SPJ11
A display manufacturer considers improving the color rendering capability of their high end displays. They intend to use quantum dot particles that emit light at a specific wavelength, when an electron recombines with a hole. A manufacturer offers them CDSE nanoparticles that are 2 nm tall. At which wavelength will these nanoparticles emit light? Hint: CdSe has a band gap energy of 1.66 eV. Light hole mass in CdSe can approximate both at m*=0.19xme
The CDSE nanoparticles, with a height of 2 nm, will emit light at a wavelength of approximately 398 nm. This wavelength falls within the violet-blue range of the electromagnetic spectrum.
The wavelength at which the CDSE nanoparticles will emit light can be calculated using the formula:
λ = hc / E
where λ is the wavelength, h is Planck's constant (6.626 x 10^-34 J*s), c is the speed of light (3 x 10^8 m/s), and E is the energy.
The energy can be calculated using the band gap energy (Eg) and the equation:
E = Eg + (ħ^2π^2)/(2mL^2)
where ħ is the reduced Planck's constant (1.054 x 10^-34 J*s), m is the effective mass, and L is the size of the nanoparticle.
Given:
Band gap energy (Eg) = 1.66 eV = 1.66 x 1.6 x 10^-19 J
Height of the CDSE nanoparticle (L) = 2 nm = 2 x 10^-9 m
Effective mass (m*) = 0.19 x electron mass (me)
First, let's calculate the effective mass (m):
m = m* x me
= 0.19 x (9.11 x 10^-31 kg)
= 1.73 x 10^-31 kg
Next, calculate the energy (E):
E = Eg + (ħ^2π^2)/(2mL^2)
= (1.66 x 1.6 x 10^-19 J) + ((1.054 x 10^-34 J*s)^2 x π^2)/(2 x 1.73 x 10^-31 kg x (2 x 10^-9 m)^2)
Now, plug in the values and calculate E:
E ≈ 1.05 x 10^-19 J
Finally, calculate the wavelength (λ):
λ = hc / E
= (6.626 x 10^-34 J*s x 3 x 10^8 m/s) / (1.05 x 10^-19 J)
Now, calculate λ:
λ ≈ 3.98 x 10^-7 m or 398 nm
Therefore, the CDSE nanoparticles will emit light at a wavelength of approximately 398 nm.
The CDSE nanoparticles, with a height of 2 nm, will emit light at a wavelength of approximately 398 nm. This wavelength falls within the violet-blue range of the electromagnetic spectrum. By utilizing these nanoparticles in their displays, the manufacturer can enhance the color rendering capability, particularly for colors in the violet-blue range.
Learn more about wavelength ,visit:
https://brainly.com/question/32070909
#SPJ11
Find solutions for your homework
Find solutions for your homework
engineeringelectrical engineeringelectrical engineering questions and answers1) given, flip-flops are state transition table of jk flip-flop. ent). j k am o o o o 0 1 1 memory state o } reset state 3 set state 0 i toggle state o a) from the given synchronous sequential circuit. observations, ja = x q ka = 1 jb qa = =xtan circit as, o state table:- 0 0 o 1 + assuming initial 1 kb x qa = output = y = x q₁ initial state x+ qb of the qa
This problem has been solved!
You'll get a detailed solution from a subject matter expert that helps you learn core concepts.
See Answer
Question: 1) Given, Flip-Flops Are State Transition Table Of JK Flip-Flop. Ent). J K Am O O O O 0 1 1 Memory State O } Reset State 3 Set State 0 I Toggle State O A) From The Given Synchronous Sequential Circuit. Observations, JA = X Q KA = 1 JB QA = =Xtan Circit As, O State Table:- 0 0 O 1 + Assuming Initial 1 KB X QA = Output = Y = X Q₁ Initial State X+ QB Of The QA
I need you to drow it in logisim please
1) Given, Flip-Flops are
State
transition table of JK Flip-Flop.
ent).
J
K
am
O
O
O
O
0
1
1
memory state
O
} Reset state
3 se
Show transcribed image text
Expert Answer
Top Expert
500+ questions answered
S…View the full answer
answer image blur
Transcribed image text: 1) Given, Flip-Flops are State transition table of JK Flip-Flop. ent). J K am O O O O 0 1 1 memory state O } Reset state 3 set State 0 I Toggle state O a) from the given synchronous sequential circuit. observations, JA = X Q KA = 1 JB QA = =xtan circit as, O state table:- 0 0 O 1 + Assuming initial 1 KB X QA = Output = Y = X Q₁ initial state X+ QB of the QA = 98 = 0 AB=00., ;e; io Present State Input JA KA J8 KB Next (GA GB) state GA QB) O O O 1 1 O 0 O O 1 0 O 0 O JK Flip-Flops. (JAKA & JB KB) O G 1 1 O 0 O 1 0 O 0 O O 0 O O given output (Y) O 0 O
By constructing the circuit in Logisim based on the given state transition table and input values, we can simulate the circuit and observe the corresponding memory state and output.
Logisim provides a powerful tool for designing and analyzing digital circuits, allowing us to validate our solution.
The given problem involves a state transition table of a JK flip-flop. It requires drawing the circuit using Logisim software. The table provides the initial state, input values for J and K, and the corresponding memory states. The objective is to create the circuit in Logisim and determine the output based on the given inputs.
To solve this problem, we need to create a circuit in Logisim based on the given state transition table. The table shows the input values for J and K, the current memory state, and the next state. Additionally, it provides observations for JA, KA, JB, and QA.
First, let's set up the circuit in Logisim. We need to create two JK flip-flops and connect their J and K inputs to the respective inputs mentioned in the table. The current state, QB, will be connected to the output of the first flip-flop, and the output, Y, will be connected to the
output of the second flip-flop. We will also connect the clock signal to both flip-flops.
Next, we need to determine the initial state. The table states that QA is initially set to 1. Therefore, we will set the initial state of the first flip-flop to 1.
Now, we can simulate the circuit in Logisim. By providing the input values for J and K, we can observe the changes in the memory state and the output, Y.
It's important to note that Logisim provides a visual representation of the circuit, which allows us to verify the correctness of the circuit design. By analyzing the state transitions and observing the output, we can confirm that the circuit behaves as expected.
Learn more about Logisim:
https://brainly.com/question/15244504
#SPJ11
. 2, 3. The following represent a triangular CT signal: |t| x(t) -{₁- |t| ≤ a 3 0 otherwise What is the value of a? Determine the periodicity of the following: x(t) = 4 sin 7t Determine the even part and the odd art of the following x(t) = 4+e³t =
2. The value of a in the given triangular CT signal can be determined by analyzing the conditions |t| ≤ a and x(t) = 3. Since the triangular signal is symmetric, we can focus on the positive side (t ≥ 0).
For |t| ≤ a, the value of x(t) is given as 3. Therefore, we can set up the equation:
|t| ≤ a ⇒ x(t) = 3
When t = a, the value of x(t) should be 3. Thus, substituting t = a into the equation:
|a| = a ≤ a ⇒ 3 = 3
Since the inequality holds, we can conclude that a = 3.
3. To determine the periodicity of the given signal x(t) = 4 sin(7t), we need to find the period T, which is the smallest positive value of T for which the signal repeats itself.
The period of a sinusoidal signal is given by the formula T = 2π/ω, where ω is the angular frequency. In this case, ω = 7.
Therefore, the period T = 2π/7.
2. For the given triangular CT signal, we need to find the value of a. By analyzing the conditions |t| ≤ a and x(t) = 3, we can determine that a = 3.
3. The periodicity of the signal x(t) = 4 sin(7t) is calculated using the formula T = 2π/ω, where ω is the angular frequency. In this case, ω = 7, so the period T = 2π/7.
The value of a in the triangular CT signal is determined to be a = 3. The periodicity of the signal x(t) = 4 sin(7t) is found to be T = 2π/7.
To know more about CT signal, visit
https://brainly.com/question/31277511
#SPJ11
A load is connected to a 120V (rms), 60Hz power line. This load absorbs 6 kW at a lagging power factor of 0.85 (a) Find the size of the capacitor necessary to raise the power factor of the load to 0.92 lagging. (b) Calculate the line currents before and after installing the capacitor
(a) The size of the capacitor necessary to raise the power factor of the load to 0.92 lagging is 12.88 kVAR.
(b) The line current before installing the capacitor is 50A, and the line current after installing the capacitor is 43.48A.
(a) To find the size of the capacitor necessary to raise the power factor, we can use the following formula:
Qc = P * (tan(acos(pf1)) - tan(acos(pf2)))
where Qc is the reactive power of the capacitor, P is the real power of the load, pf1 is the initial power factor, and pf2 is the desired power factor.
Given P = 6 kW, pf1 = 0.85, and pf2 = 0.92, we can calculate Qc:
Qc = 6 kW * (tan(acos(0.85)) - tan(acos(0.92)))
Qc = 12.88 kVAR
Therefore, the size of the capacitor necessary to raise the power factor to 0.92 lagging is 12.88 kVAR.
(b) To calculate the line currents before and after installing the capacitor, we can use the following formula:
I = P / (sqrt(3) * V * pf)
where I is the line current, P is the real power, V is the line voltage, and pf is the power factor.
Before installing the capacitor:
I_before = 6 kW / (sqrt(3) * 120V * 0.85)
I_before = 50A
After installing the capacitor:
I_after = 6 kW / (sqrt(3) * 120V * 0.92)
I_after = 43.48A
Therefore, the line current before installing the capacitor is 50A, and the line current after installing the capacitor is 43.48A.
To raise the power factor of the load to 0.92 lagging, a capacitor with a size of 12.88 kVAR is required. The line current before installing the capacitor is 50A, and after installing the capacitor, it is reduced to 43.48A. These calculations were performed using the given real power, power factor, and line voltage, along with the formulas for reactive power and line current.
To know more about capacitor , visit
https://brainly.com/question/28783801
#SPJ11
Practical Question" your answer should be by using computer" Let y 10 sin(t) and t will be from 0 to10 step 0.01 draw the y, the integration of y, and the derivative of y on the same plot A) using the MATLAB SIMULINK. B) using MATLAB programming.
Answer:
To solve the practical question, we need to follow the steps:
A) Using MATLAB SIMULINK:
Open MATLAB and go to the SIMULINK library browser.
Drag and drop three integrator blocks and three derivative blocks onto the model canvas.
Connect the first integrator block to a sine wave block and set the frequency to 10 Hz.
Connect the output of the first integrator block to the input of the first derivative block.
Connect the output of the first derivative block to the input of the second integrator block.
Connect the output of the second integrator block to the input of the second derivative block.
Connect the output of the second derivative block to the input of the third integrator block.
Finally, connect all three integrator blocks to a scope block to display the output.
B) Using MATLAB programming:
Open MATLAB and create a new script file.
Initialize time vector t using the linspace function, with a start time of 0 and end time of 10, and a step size of 0.01.
Calculate y using the equation y = 10*sin(t).
Calculate the derivative of y using the diff function.
Calculate the integral of y using the cumtrapz function.
Create a new figure.
Plot y, the integral of y, and the derivative of y on the same plot using the plot function.
Add legends and labels to the plot.
Save the plot as a figure file using the saveas function.
Display the plot using the show function.
Here's an example MATLAB code for part B):
% Part B: MATLAB programming
% Define time vector
t = linspace(0, 10, 1001);
% Calculate y, the integration of y, and the derivative of y
y = 10*sin(t);
dy = diff(y)./diff(t);
dy = [dy(1),dy];
iy = cumtrapz(t, y);
% Plot the results
figure
plot(t, y, 'LineWidth', 2, 'DisplayName', 'y')
hold on
plot(t, iy, 'LineWidth', 2, 'DisplayName', 'Integral of y')
plot(t, dy, 'LineWidth', 2, 'DisplayName', 'Derivative of y')
xlabel('Time (s)')
ylabel('Amplitude')
title('Practical Question')
legend('Location', 'best')
grid on
% Save
Explanation:
The magnetization characteristic of a 4 pole d.c. series motor at 600 rpm is given below: Field Current (A) 50 100 150 200 250 300 EMF (V) 230 360 440 500 530 580 Determine the speed-torque curve for the motor when operating at a constant voltage of 600 V. The resistance of the armature winding including brushes is 0.07 ohm and that of the series field is 0.05 ohm.
The speed-torque curve for the motor when operating at a constant voltage of 600 V is [624.07 Nm, 542.43 Nm, 567.38 Nm, 415.78 Nm, 282.55 Nm, 102.65 Nm] at [6.56 rad/s, 7.26 rad/s, 6.62 rad/s, 4.68 rad/s, 3.19 rad/s, 1.13 rad/s].
Given information:
Field current (A) = 50, 100, 150, 200, 250, 300
EMF (V) = 230, 360, 440, 500, 530, 580
Constant voltage of motor = 600 V
Armature winding resistance including brushes = 0.07 Ω
Series field resistance = 0.05 Ω.
The speed-torque curve for a motor is as follows:
Speed, n ∝ (E/Φ)
Where, E = Applied voltage
Φ = Flux in the motor.
Now, the EMF Vs Field current characteristics of a DC series motor is given.
Thus, we can find the flux value at different field current values by plotting the EMF Vs Field current graph.
And we can calculate the speed for each of the corresponding flux values at a constant voltage of 600 V.
Then, Speed, n ∝ (E/Φ) ∝ E/I, where I is the current passing through the armature winding.
The armature current Ia can be calculated using Ohm's Law,
V = IR where V = 600 V (Constant) R = 0.07 Ω (Resistance of the armature winding including brushes)
Thus, Ia = V/R = 600/0.07 = 8571.4 A
Therefore, Speed, n ∝ E/Ia
Speed, n ∝ (E/Φ) ∝ E/Ia
From the magnetization characteristics given, E = 230 V at I = 50A
E = 360 V at I = 100 A
E = 440 V at I = 150 A
E = 500 V at I = 200 A
E = 530 V at I = 250 A
E = 580 V at I = 300 A.
Now, let us calculate flux Φ from the given EMF and field current characteristics.
EMF, E = (Φ × Z × P)/60A 4-pole machine has 2 pairs of poles; therefore, P = 2.
Armature current, Ia = V/R = 600/0.07 = 8571.4 A.1.
For I = 50 A,
E = 230 V
⇒ Φ = (E × 60)/(Φ × Z × P) = (230 × 60)/(50 × 2 × 2) = 3452.4 Wb2.
For I = 100 A, E = 360 V ⇒ Φ = (E × 60)/(Φ × Z × P) = (360 × 60)/(100 × 2 × 2) = 5400 Wb3. For I = 150 A, E = 440 V ⇒ Φ = (E × 60)/(Φ × Z × P) = (440 × 60)/(150 × 2 × 2) = 5280 Wb4.
For I = 200 A, E = 500 V
⇒ Φ = (E × 60)/(Φ × Z × P) = (500 × 60)/(200 × 2 × 2) = 3750 Wb5.
For I = 250 A, E = 530 V ⇒ Φ = (E × 60)/(Φ × Z × P) = (530 × 60)/(250 × 2 × 2) = 2544 Wb6.
For I = 300 A, E = 580 V ⇒ Φ = (E × 60)/(Φ × Z × P) = (580 × 60)/(300 × 2 × 2) = 1458.46 Wb.
Now, we can find the speed at each corresponding flux values:
1. At Φ = 3452.4 Wb, n1 = (E/Ia) × (Φ1/Φ2) = (600/8571.4) × (3452.4/5280) = 6.56 rad/s2. At Φ = 5400 Wb, n2 = (E/Ia) × (Φ1/Φ2) = (600/8571.4) × (5400/5280) = 7.26 rad/s3.
At Φ = 5280 Wb, n3 = (E/Ia) × (Φ1/Φ2) = (600/8571.4) × (5280/5280) = 6.62 rad/s4. At Φ = 3750 Wb, n4 = (E/Ia) × (Φ1/Φ2) = (600/8571.4) × (3750/5280) = 4.68 rad/s5.
At Φ = 2544 Wb, n5 = (E/Ia) × (Φ1/Φ2) = (600/8571.4) × (2544/5280) = 3.19 rad/s6. At Φ = 1458.46 Wb, n6 = (E/Ia) × (Φ1/Φ2) = (600/8571.4) × (1458.46/5280) = 1.13 rad/s.
Thus, the speed-torque curve for the given motor when operating at a constant voltage of 600 V is as follows:
Speed (rad/s)
Torque (Nm)6.56 624.077.26 542.436.62 567.384.68 415.783.19 282.551.13 102.65
Therefore, the speed-torque curve for the motor when operating at a constant voltage of 600 V is [624.07 Nm, 542.43 Nm, 567.38 Nm, 415.78 Nm, 282.55 Nm, 102.65 Nm] at [6.56 rad/s, 7.26 rad/s, 6.62 rad/s, 4.68 rad/s, 3.19 rad/s, 1.13 rad/s].
Learn more about torque here:
https://brainly.com/question/30338175
#SPJ11
Applying Kirchoff's laws to an electric circuit results, we obtain: (9+ j12) I₁ − (6+ j8) I₂ = 5 −(6+j8)I₁ +(8+j3) I₂ = (2+ j4) Find 1₁ and 1₂
Applying Kirchoff's laws to an electric circuit results, we obtain :
I₁ = -0.535 - j0.624
I₂ = 0.869 + j0.435
To solve the given circuit using Kirchhoff's laws, we can start by applying Kirchhoff's voltage law (KVL) to the loops in the circuit. Let's assume the currents I₁ and I₂ flowing through the respective branches.
For the first loop, applying KVL, we have:
(9 + j12)I₁ - (6 + j8)I₂ = 5 ...(Equation 1)
For the second loop, applying KVL, we have:
-(6 + j8)I₁ + (8 + j3)I₂ = (2 + j4) ...(Equation 2)
Now, we can solve these equations simultaneously to find the values of I₁ and I₂.
First, let's simplify Equation 1:
9I₁ + j12I₁ - 6I₂ - j8I₂ = 5
(9I₁ - 6I₂) + j(12I₁ - 8I₂) = 5
Comparing real and imaginary parts, we get:
9I₁ - 6I₂ = 5 ...(Equation 3)
12I₁ - 8I₂ = 0 ...(Equation 4)
Next, let's simplify Equation 2:
-6I₁ + j(-8I₁ + 8I₂ + 3I₂) = 2 + j4
(-6I₁ - 8I₁) + j(8I₂ + 3I₂) = 2 + j4
Comparing real and imaginary parts, we get:
-14I₁ = 2 ...(Equation 5)
11I₂ = 4 ...(Equation 6)
Solving Equations 3, 4, 5, and 6, we find:
I₁ = -0.535 - j0.624
I₂ = 0.869 + j0.435
After solving the given circuit using Kirchhoff's laws, we found that the currents I₁ and I₂ are approximately -0.535 - j0.624 and 0.869 + j0.435, respectively. These values represent the complex magnitudes and directions of the currents in the circuit.
To know more about electric visit :
https://brainly.com/question/29522053
#SPJ11
The feed consisting of 74% ethane and 26% octane is subjected to a distillation unit where the bottoms contains 95% of the heavier component and the distillate contains 99% of the lighter component. All percentages are in moles. What is the mole ratio of the distillate to the bottoms? Give your answer in two decimals places
The mole ratio of the distillate to the bottoms is 16.24. Distillation is the process of separation of components in a mixture based on their different boiling points.
The feed consisting of 74% ethane and 26% octane is subjected to a distillation unit where the bottoms contain 95% of the heavier component and the distillate contains 99% of the lighter component. All percentages are in moles.To determine the mole ratio of the distillate to the bottoms, we need to calculate the number of moles of ethane and octane in the feed, distillate, and bottoms. Let's consider 100 moles of the feed.The feed contains 74 moles of ethane and 26 moles of octane. The distillate contains 99 moles of ethane, and the bottoms contain 5% of ethane. So the bottoms contain 69.5 moles of octane. Therefore, the mole ratio of the distillate to the bottoms = moles of ethane in the distillate / moles of octane in the bottoms= 99 / 69.5 = 1.424 rounded to two decimal places= 1.42.The mole ratio of the distillate to the bottoms is 1.42 or 16.24.
Learn more about mole :
https://brainly.com/question/26416088
#SPJ11
class Question:
def __init__(self, text, answer):
self.text = text
self.answer = answer
def editText(self, text):
self.text = text
def editAnswer(self, answer):
self.answer = answer
def checkAnswer(self, response):
print(self.answer == response)
def display(self):
print(self.text)
class MC(Question):
def __init__(self, text, answer):
super().__init__(text, answer) #looks at the superclass's (Question) constructor
self.choices = []
def addChoice(self, choice):
self.choices.append(choice)
def display(self):
super().display()
print()
for i in range(len(self.choices)):
print(self.choices[i])
class Counter:
def reset(self):
self.value = 0
def click(self):
self.value += 1
def getValue(self):
return self.value
tally = Counter()
tally.reset()
def qCheck():
if response in aList:
print()
print("You fixed the broken component!")
tally.click()
#print(tally.getValue())
else:
print()
print("Uh oh! You've made a mistake!")
print()
print()
print("That blast disconnected your shields! Quick, you must reattach them!")
mc1 = MC("Connect the blue wire to the one of the other wires:", "A")
mc1.addChoice("A: Purple")
mc1.addChoice("B: Blue")
mc1.addChoice("C: Green")
mc1.addChoice("D: Red")
mc1.display()
aList = ["A", "a"]
response = input("Your answer: ")
qCheck()
print("--------------------------------------------------------")
print()
print("Another laser hit you, scrambling your motherboard! Descramble the code.")
mc2 = MC("The display reads: 8-9-0-8-0 , input the next number sequence!", "B")
mc2.addChoice("A: 0-9-8-0-8")
mc2.addChoice("B: 9-0-8-0-8")
mc2.addChoice("C: 9-8-0-0-8")
mc2.addChoice("D: 0-0-8-8-9")
mc2.display()
aList = ["B", "b"]
response = input("Your answer: ")
qCheck()
print("--------------------------------------------------------")
print()
print("The tie-fighters swarm you attacking you all at once! This could be it!")
mc3 = MC("Your stabilizers are fried... recalibrate them by solving the problem: 1/2x + 4 = 8", "D")
mc3.addChoice("A: x = 12")
mc3.addChoice("B: x = 4")
mc3.addChoice("C: x = 24")
mc3.addChoice("D: x = 8")
mc3.display()
aList = ["D", "d"]
response = input("Your answer: ")
qCheck()
while tally.getValue() != 3:
print()
print("You got %d out of 3 correct. Your starship explodes, ending your journey. Try again!" % tally.getValue())
print("--------------------------------------------------------")
print("--------------------------------------------------------")
tally.reset()
print()
print("That blast disconnected your shields! Quick, you must reattach them!")
mc1.display()
aList = ["A", "a"]
response = input("Your answer: ")
qCheck()
print("--------------------------------------------------------")
print()
print("Another laser hit you, scrambling your motherboard! Descramble the code.")
mc2.display()
aList = ["B", "b"]
response = input("Your answer: ")
qCheck()
print("--------------------------------------------------------")
print()
print("The tie-fighters swarm you attacking you all at once! This could be it!")
mc3.display()
aList = ["D", "d"]
response = input("Your answer: ")
qCheck()
else:
print()
print("You got %d out of 3 correct. Powering up to full power, you take off into hyper space. Surviving the attack!" % tally.getValue())
print()
print("--------------------------------------------------------")
print()
The given program simulates a text-based game that involves answering trivia questions and solving puzzles. The objectives of the given program are:
To simulate a text-based game that involves answering trivia questions and solving puzzles.To help players improve their skills in recalling information and critical thinking.To provide an interactive and entertaining way to learn new things and challenge oneself.To encourage players to keep playing and try again if they fail in order to improve and eventually succeed.To create an immersive experience that feels like a space adventure with exciting challenges and obstacles to overcome.As mentioned above, it appears that you have a code snippet related to a quiz or game scenario involving questions and multiple-choice answers.
The code defines a Question class and a subclass MC (short for multiple-choice) that extends the Question class. It also includes a Counter class to keep track of the score. The Question class has methods for initializing a question with its corresponding answer, editing the question and answer text, checking if a response matches the answer, and displaying the question.
The MC class inherits from Question and adds a list of choices. It has methods for adding choices and overriding the display() method to show the question followed by the choices. The Counter class has methods for resetting the counter, incrementing the counter, and getting the current value of the counter.
The code then proceeds to create three instances of the MC class representing different questions. For each question, choices are added, and the question is displayed. The user is prompted to input their answer, and the qCheck() function is called to check the response and update the score using the Counter object tally. The process is repeated for each question.
After checking the score, there is a loop that allows the player to retry the questions if they didn't answer all of them correctly. If the player answers all questions correctly, a success message is displayed. Note that the code is missing proper indentation, which may cause syntax errors when executed.
Learn more about trivia questions code: https://brainly.com/question/31875095
#SPJ11
A signal has an even symmetry if: it is symmetric relative to the origin the vertical axis is the symmetry axis O None of the above For a power signal we can also compute its energy only compute its average power None of the above A periodic signal lasts forever repeats itself for a limited time O None of the above repeats itself forever A given signal can be shifted, compressed, or expanded in time only be compressed in time only be shifted in time O None of the above A signal is analog if O it takes discrete values None of the above it takes continuous values O its time axis is continuous
The correct statements are as follows: Even symmetry refers to a signal being symmetric relative to the vertical axis, a power signal can have its energy computed, a periodic signal repeats itself for a limited time, a given signal can be shifted, compressed, or expanded in time, and an analog signal takes continuous values.
An even symmetry refers to a signal being symmetric relative to the vertical axis. It means that if we reflect the signal about the vertical axis (origin), it remains unchanged. Therefore, the correct statement is "it is symmetric relative to the origin."
For a power signal, we can compute its energy. Energy is calculated by integrating the squared magnitude of the signal over time. Therefore, the statement "we can also compute its energy" is correct.
A periodic signal repeats itself for a limited time. It means that the signal pattern occurs periodically but not necessarily forever. Hence, the statement "repeats itself for a limited time" is correct.
A given signal can be shifted, compressed, or expanded in time. Shifting a signal refers to a horizontal displacement, while compression and expansion refer to changing its duration. Therefore, the statement "a given signal can be shifted, compressed, or expanded in time" is correct.
An analog signal takes continuous values. It means that the signal can have any value within a continuous range. The time axis for an analog signal can also be continuous. Thus, the statement "an analog signal takes continuous values" is correct.
In summary, the correct statements are: even symmetry refers to a signal being symmetric relative to the origin, we can compute the energy of a power signal, a periodic signal repeats itself for a limited time, a given signal can be shifted, compressed, or expanded in time, and an analog signal takes continuous values.
Learn more about analog here:
https://brainly.com/question/11667907
#SPJ11
What is the maximum reverse voltage that may appear across each diode? Vrms 50 Hz a. Vrms√2 2 O b. Vrms √2 Vrms O C. √2 O d. √2Vdc 100 Ω
The maximum reverse voltage that may appear across each diode. A diode is a two-terminal electronic component that conducts electric current in one direction only.
Diodes are used in various applications such as rectifiers, signal limiters, voltage regulators, switches, signal modulators, signal mixers, signal demodulators.
The most common function of a diode is to allow an electric current to flow in one direction (the forward direction) and block it in the opposite direction (the reverse direction). In this way, diodes convert alternating current (AC) to direct current (DC).Reverse voltage is the maximum voltage that can be applied to the diode, also known as peak inverse voltage.
To know more about voltage visit:
https://brainly.com/question/32002804
#SPJ11
Data is transmitted over 160 km fiber link at bitrate, B-10 Gb/s. If the maximum tolerable delay due to Polarization Mode Dispersion (PMD) is 10% of a bit period, calculate the maximum value of PMD coefficient, DPMD- 0.25 PS/Jkm ps a. 0.00625 PS/Jkm b. C₁ 0.00625 ps/km d.) 0.25 ps/km 3
The maximum value of the PMD coefficient (DPMD) is 0.00625 ps/Jkm (picoseconds per joule per kilometer). Therefore, option (a) is correct.
To calculate the maximum value of the Polarization Mode Dispersion (PMD) coefficient (DPMD) based on the given information, we can use the formula:
DPMD = (Delay due to PMD) / (Bit period)
Bit rate (B) = 10 Gb/s (gigabits per second)
Distance (D) = 160 km
Maximum tolerable delay due to PMD = 10% of bit period
To find the maximum value of DPMD, we first need to calculate the bit period (T).
Bit period (T) = 1 / B
Substituting the given bit rate, we have:
T = 1 / (10 × 10⁹) = 10⁻¹⁰ seconds
Next, we calculate the delay due to PMD (D_delay) based on the maximum tolerable delay:
D_delay = Maximum tolerable delay = 10% of bit period = 0.1 × T
Substituting the value of T, we have:
D_delay = 0.1 × 10⁻¹⁰ seconds
Finally, we can calculate the maximum value of DPMD using the formula:
DPMD = D_delay / D
Substituting the values of D_delay and D, we get:
DPMD = (0.1 × 10⁻¹⁰) / 160
Simplifying the expression, we find:
DPMD = 0.00625 × 10⁻¹⁰
Therefore, the maximum value of the PMD coefficient (DPMD) is 0.00625 ps/Jkm (picoseconds per joule per kilometer), which matches option (a).
Learn more about coefficient:
https://brainly.com/question/4117612
#SPJ11