a) The probability that a randomly selected peanut M&M is not brown is: 88%
b) The probability that a randomly selected peanut is brown or yellow is; 27%
c) The probability that two randomly selected peanut are both blue is:
5.29%
d) If we randomly select three peanuts, the probability that none are yellow is: 56.25%
How to find the Probability of selection?We are given the parameters as:
Percentage of brown peanuts = 12%
Percentage of Yellow Peanuts = 15%
Percentage of red peanuts = 12%
Percentage of blue peanuts = 23%
Percentage of orange peanuts = 23%
Percentage of green peanuts = 15%
Thus:
a) The probability that a randomly selected peanut M&M is not brown is:
We know that P (brown) = 12%
Thus:
P(brown)^(c) = 1 - P(brown)
P(brown)^(c) = 100% - 12%
P(brown)^(c) = 88%
b) The probability that a randomly selected peanut is brown or yellow is;
P(brown or yellow) = P(brown) + P(yellow)
P(brown or yellow) = 12% + 15%
= 27%
c) The probability that two randomly selected peanut are both blue is:
P(blue)² = (23%)²
P(blue)² = 5.29%
d) If we randomly select three peanuts, the probability that none are yellow is:
(1 - P(yellow))³
= (1 - 15%)³
= 56.25%
Read more about Probability of Selection at: https://brainly.com/question/251701
#SPJ4
Reinforced concrete beam having a width of 500 mm and an effective depth of 750 mm is reinforced with 5 – 25mm p. The beam has simple span of 10 m. It carries an ultimate uniform load of 50 KN/m. Use f'c = 28 MPa, and fy = 413 MPa. Determine the ultimate moment capacity in KN- m when two bars are cut at a distance from the support. Express your answer in two decimal places.
The ultimate moment capacity of the reinforced concrete beam when two bars are cut at a distance from the support is approximately 157.10 kN-m, expressed in two decimal places.
To determine the ultimate moment capacity of the reinforced concrete beam when two bars are cut at a distance from the support, we need to consider the bending moment and the reinforcement provided.
Given:
Width of the beam (b): 500 mm
Effective depth (d): 750 mm
Reinforcement diameter (ϕ): 25 mm
Span (L): 10 m
Ultimate uniform load (w): 50 kN/m
Concrete compressive strength (f'c): 28 MPa
Steel yield strength (fy): 413 MPa
First, we need to calculate the neutral axis depth (x) based on the given dimensions and reinforcement.
For a rectangular beam with tension reinforcement only, the neutral axis depth is given by:
[tex]x = (A_{st} * fy) / (0.85 * f'c * b)[/tex]
Where:
[tex]A_{st[/tex] = Area of steel reinforcement
[tex]A_{st[/tex] = (number of bars) × (π × (ϕ/2)²)
Given that there are 5 - 25 mm diameter bars, the area of steel reinforcement is:
[tex]A_{st[/tex] = 5 × (π × (25/2)²)
= 5 × (π × 6.25)
= 98.174 mm²
Converting [tex]A_{st[/tex] to square meters:
[tex]A_{st[/tex] = 98.174 mm² / (1000 mm/m)²
= 0.000098174 m²
Now we can calculate the neutral axis depth:
x = (0.000098174 m² × 413 MPa) / (0.85 × 28 MPa × 0.5 m)
= 0.025 m
Next, we calculate the moment capacity (Mu) using the formula:
Mu = (0.85 × f'c × b × x × (d - 0.4167 × x)) / 10 + (A_st × fy × (d - 0.4167 × x)) / 10
Plugging in the values:
Mu = (0.85 × 28 MPa × 0.5 m × 0.025 m × (0.75 m - 0.4167 × 0.025 m)) / 10 + (0.000098174 m² × 413 MPa × (0.75 m - 0.4167 × 0.025 m)) / 10
Calculating the above expression, we get:
Mu ≈ 157.10 kN-m
Therefore, the ultimate moment capacity of the reinforced concrete beam when two bars are cut at a distance from the support is approximately 157.10 kN-m, expressed in two decimal places.
To know more about bending moment, visit
https://brainly.com/question/31862370
#SPJ11
Engr. Romulo of DPWH District 11 of Bulacan office analyzed the effect of wood on top of water. The wood is 0.60 m x 0.60 m x h meters in dimension. The wood floats by 0.18 m projecting above the water surface. The same block was thrown into a container of a liquid having a specific gravity of 1.03 and it floats with 0.14m projecting above the surface. Determine the following: A). Value of h.
B). Specific gravity of the wood. B).Weight of the wood.
A) Value of h = (ρwater - ρliquid) / (0.60 m x 0.60 m)
B) Specific gravity of wood = ρwood / ρliquid
C) Weight of wood = ρwood x V x g
Engr. Romulo of DPWH District 11 in Bulacan analyzed the effect of wood on top of water. The wood has dimensions of 0.60 m x 0.60 m x h meters. It floats with 0.18 m projecting above the water surface. When the same block was thrown into a container of liquid with a specific gravity of 1.03, it floats with 0.14 m projecting above the surface.
A) To determine the value of h, we can equate the buoyant forces acting on the wood in both cases. The buoyant force is equal to the weight of the displaced liquid. In the first case, the buoyant force is equal to the weight of the wood. In the second case, the buoyant force is equal to the weight of the wood plus the weight of the liquid displaced by the wood.
Using the formula for buoyant force (B = ρVg), where B is the buoyant force, ρ is the density of the liquid, V is the volume of the displaced liquid, and g is the acceleration due to gravity, we can set up the following equation:
(0.60 m x 0.60 m x h m) x (ρwater x g) = (0.60 m x 0.60 m x h m) x (ρliquid x g) + (0.60 m x 0.60 m x 0.18 m) x (ρliquid x g)
Simplifying the equation, we can cancel out the common factors:
ρwater = ρliquid + (0.60 m x 0.60 m x 0.18 m)
Now we can solve for h:
h = (ρwater - ρliquid) / (0.60 m x 0.60 m)
B) To determine the specific gravity of the wood, we can use the definition of specific gravity, which is the ratio of the density of the wood to the density of the liquid:
Specific gravity of wood = ρwood / ρliquid
C) To determine the weight of the wood, we can use the formula for weight (W = m x g), where W is the weight, m is the mass, and g is the acceleration due to gravity. The mass can be calculated using the formula for density (ρ = m / V), where ρ is the density, m is the mass, and V is the volume:
Weight of wood = ρwood x V x g
To learn more about specific gravity
https://brainly.com/question/22099107
#SPJ11
Please answer my question quickly!
[tex]12^6[/tex], ? = 6
Step-by-step explanation:We are given instructions by the problem. When dividing exponential expressions with the same base, we can find the difference (subtraction) between the exponents and keep the base.
[tex]\displaystyle 12^9 \div 12^3=12^{9-3}=12^6[/tex]
But why does this work?Let us write it out.
[tex]\displaystyle 12^9 \div 12^3 = \frac{12^9}{12^3} =\frac{12*12*12*12*12*12*12*12*12}{12*12*12}[/tex]
Now, 12 divided by 12 (aka [tex]\frac{12}{12}[/tex]) is equal to 1.
[tex]\displaystyle 1*1*1*12*12*12*12*12*12}[/tex]
And anything times one is itself. Then, we can rewrite this as 12 to the power of 6 because we are multiplying 12 by itself 6 times.
[tex]\displaystyle 12*12*12*12*12*12} =12^6[/tex]
An oil well has been drilled and completed. The productive zone has been encountered at a depth of 7815-7830 feet. The log analysis showed an average porosity of 15% and an average water saturation of 35%. The oil formation volume factor is determined in the laboratory to be 1.215 RB/STB. Experience shows other reservoirs of about the same properties drain 80 acres with a recovery factor of 12%. Compute the OOIP and the ultimate oil recovery. If after 5 years of production, only 5% of the reserve has been produced. What is the amount of reserve still left in place.
The amount of reserve still left in place after 5 years of production is 8,650,116.46 STB.
Percentage of reserve left in place = 95%OOIP (Original Oil in Place) is the volume of oil present in a reservoir before production, which can be calculated using the given information as follows:
Area of the reservoir = π/4 × (rod length)²
= π/4 × (15,405)
= 19,265,400 ft² = 443.6 acres
Drainage area is 80 acres, so the portion of the reservoir that contributes to production = 80/443.6
= 0.1803 of the reservoir or (1/0.1803 = 5.54) times the given volume of oil.
Estimated ultimate recovery factor (EUR) = Recovery factor × Drainage area
= 12% × 80 acres
= 9.6 acres or 0.0220 of the reservoir or (1/0.0220 = 45.45) times the given volume of oil.
The formula to calculate the original oil in place (OOIP) is:
OOIP = (7758 × A × h × φ × (1-Sw))/B
Where A = Area (acres)h = Net thickness (feet)
φ = Porosity (decimal)
Sw = Water saturation (decimal)
B = Formation volume factor (reservoir barrels per stock tank barrel)
Substituting the given values in the above formula:
OOIP = (7758 × 80 × (7815-7830) × 0.15 × (1-0.35))/1.215OOIP
= 9,105,385.46 STB
Now, the ultimate oil recovery can be calculated by multiplying OOIP by EUR.
Ultimate oil recovery = OOIP × EUR
= 9,105,385.46 × 0.0220
= 200,318.48 STB
After 5 years of production, the oil that has been produced is:
5% of OOIP = 0.05 × 9,105,385.46
= 455,269 STB
The amount of reserve still left in place after 5 years of production is 8,650,116.46 STB.
Know more about reserve here:
https://brainly.com/question/25817380
#SPJ11
Let p(x) be a polynomial of degree n with leading coefficient 1 . What is p^(k)(x) if (a) k=n; and if (b) k>n.
The values of [tex]p^(^k^)[/tex](x), where p(x) be a polynomial of degree n with leading coefficient 1 are,
(a) [tex]p^(^k^)(x) = n![/tex] if k=n.
(b)[tex]p^(^k^)(x)[/tex] = 0 if k>n.
When we have a polynomial p(x) of degree n with a leading coefficient of 1, finding the kth derivative, [tex]p^(^k^)[/tex](x), can be done in two cases:
(a) If k=n:
When the value of k is equal to the degree of the polynomial (k=n), then the kth derivative of p(x) will be n! (n factorial). This is because when we take the nth derivative, the coefficient of the leading term will be n!, and all other terms will have coefficients equal to zero.
The process of taking derivatives successively removes all the terms of lower degrees until we are left with just the nth degree term, which is n! times the leading coefficient.
(b) If k>n:
When the value of k is greater than the degree of the polynomial (k>n), the kth derivative of p(x) will be 0. This is because after taking the nth derivative, any further derivatives will result in the disappearance of all terms in the polynomial. All the coefficients of the terms will become zero, leaving us with the constant zero polynomial.
In summary, if k=n, the kth derivative will be n!, and if k>n, the kth derivative will be 0.
For further understanding, it is essential to grasp the concept of polynomial derivatives and how they affect the polynomial's terms based on their degrees. Additionally, exploring the application of polynomial derivatives in calculus and various mathematical fields can enhance comprehension.
Understanding how to find the derivative of a polynomial function can be useful in solving various real-world problems and engineering applications, making it a valuable skill for students and professionals alike.
Learn more about polynomial
brainly.com/question/11536910
#SPJ11
What is the electron domain arrangement of PF4-? (P in middle, surrounded by F's) (i.e., what is the electron pair arrangement, arrangement of areas of high electron density.) linear octahedral t-shaped see-saw bent square pyramidal trigonal planar trigonal pyramidal trigonal bipyramidal tetrahedral square planar
This arrangement is characterized by bond angles of approximately 109.5 degrees.
The electron domain arrangement of PF4- is tetrahedral. In this arrangement, the central phosphorus (P) atom is surrounded by four fluorine (F) atoms.
To determine the electron domain arrangement, we need to consider the number of electron domains around the central atom. In this case, the P atom has four bonding pairs of electrons (one from each F atom) and no lone pairs.
The tetrahedral arrangement occurs when there are four electron domains around the central atom. The four F atoms are placed at the corners of a tetrahedron, with the P atom in the center.
This arrangement results in a molecule with a symmetrical shape. The bond angles between the P-F bonds are approximately 109.5 degrees, which is characteristic of a tetrahedral arrangement.
In summary, the electron domain arrangement of PF4- is tetrahedral, with the P atom in the center and four F atoms at the corners of a tetrahedron.
The bond angles in this configuration measure roughly 109.5 degrees.
learn more about angle from given link
https://brainly.com/question/24775470
#SPJ11
We have five data points x₁=1, x₂ = 3, x₁=-1, x = 4, x5=-3 which are obtained from sampling a Gaussian distribution of zero mean. Derive the Maximum Likelihood Estimate of the variance of the Gaussian distribution and apply your derived formula to the given data set. Show all the steps in the calculation.
This is the maximum likelihood estimator of the variance of the Gaussian distribution, where $\hat{\mu}$ is the maximum likelihood estimator of the mean. We have the data points,
Let's use MLE to find the variance of the Gaussian distribution for the given dataset. The probability density function (PDF) of a Gaussian distribution with mean $\mu$ and variance $\sigma^2$ is given by $f(x)=\frac{1}{\sqrt{2\pi\sigma^2}}e^{-\frac{(x-\mu)^2}{2\sigma^2}}$
The likelihood function is given by $L(\mu, \sigma^2|x_1,x_2,...,x_n) = \prod_{i=1}^{n}f(x_i)$
Taking the logarithm of the likelihood function,$\ln{L} = -\frac{n}{2}\ln{2\pi}-n\ln{\sigma}-\sum_{i=1}^{n}\frac{(x_i-\mu)^2}{2\sigma^2}$Differentiating the logarithm of the likelihood function with respect to $\sigma$ and equating it to 0, we get,
[tex]$$\frac{d}{d\sigma}(\ln{L}) = -\frac{n}{\sigma}+\sum_{i=1}^{n}\frac{(x_i-\mu)^2}{\sigma^3}=0$$[/tex]Solving for $\sigma^2$, we get, $$\hat{\sigma^2} = \frac{1}{n}\sum_{i=1}^{n}(x_i-\hat{\mu})^2$$
[tex]$x_1=1$, $x_2=3$, $x_3=-1$, $x_4=4$,[/tex] and $x_5=-3$. The sample mean is given by,$$\hat{\mu} = \frac{1}{5}\sum_{i=1}^{5}x_i = \frac{4}{5}$$Therefore,
To know more about variance visit:
https://brainly.com/question/31432390
#SPJ11
What are the coefficients when the reaction below is balanced? Nitrogen dioxide reacts with dihydrogen dioxide to produce nitric acid (nitric acid is HNO3)
The balanced equation for the reaction between nitrogen dioxide (NO2) and dihydrogen dioxide (H2O2) to produce nitric acid (HNO3) is:
2 NO2 + H2O2 → 2 HNO3
The balanced equation for the reaction between nitrogen dioxide (NO2) and dihydrogen dioxide (H2O2) to produce nitric acid (HNO3) is obtained by ensuring that the number of atoms of each element is equal on both sides of the equation.
In this reaction, we have two nitrogen dioxide molecules (2 NO2) reacting with one dihydrogen dioxide molecule (H2O2) to produce two molecules of nitric acid (2 HNO3).
To balance the equation, we need to adjust the coefficients in front of each compound to achieve an equal number of atoms on both sides. The balanced equation is:
2 NO2 + H2O2 → 2 HNO3
This equation indicates that two molecules of nitrogen dioxide react with one molecule of dihydrogen dioxide to produce two molecules of nitric acid.
TO learn more about balanced equation visit:
https://brainly.com/question/11904811
#SPJ11
Drag the tiles to the correct boxes to complete the pairs.
Determine whether each pair of lines is perpendicular, parallel, or neither.
The pair y = 2x + 4 and 2y = 4x - 7 is parallel.
The pair 2y = 4x + 4 and y = -2x + 2 is perpendicular.
The pair 4y = 2x + 4 and y = -2x + 9 is neither parallel nor perpendicular.
To determine whether each pair of lines is perpendicular, parallel, or neither, we can compare their slopes. Recall that two lines are parallel if and only if their slopes are equal, and two lines are perpendicular if and only if the product of their slopes is -1.
Let's analyze each pair of lines:
y = 2x + 4 and 2y = 4x - 7:
To compare the slopes, we need to write the second equation in slope-intercept form. Dividing both sides of the equation by 2, we get y = 2x - 7/2. Now we can see that the slope of the first line is 2, and the slope of the second line is also 2. Since the slopes are equal, these two lines are parallel.
2y = 4x + 4 and y = -2x + 2:
Again, let's write the first equation in slope-intercept form by dividing both sides by 2: y = 2x + 2. Comparing the slopes, we see that the slope of the first line is 2, and the slope of the second line is -2. Since the slopes are negative reciprocals of each other (their product is -1), these two lines are perpendicular.
4y = 2x + 4 and y = -2x + 9:
In this case, let's rewrite the first equation in slope-intercept form by dividing both sides by 4: y = (1/2)x + 1. Comparing the slopes, we see that the slope of the first line is 1/2, and the slope of the second line is -2. The slopes are not equal, and their product is not -1, so these two lines are neither parallel nor perpendicular.
For more such questions on parallel visit:
https://brainly.com/question/30097515
#SPJ8
You won $100000.00 in a lottery and you want to set some of that sum aside for 4 years. After 4 years you would like to receive $2000.00 at the end of every 3 months for 6 years. If interest is 5% compounded semi-annually, how much of your winnings must you set aside?
Answer: you would need to set aside approximately $39,742.72 from your lottery winnings to receive $2,000 at the end of every 3 months for 6 years, assuming a 5% interest rate compounded semi-annually.
To calculate the amount you need to set aside from your lottery winnings, we can use the concept of present value. Present value is the current value of a future amount of money, taking into account the time value of money and the interest rate.
First, let's calculate the present value of receiving $2,000 at the end of every 3 months for 6 years.
Since the interest is compounded semi-annually, we need to adjust the interest rate accordingly. The interest rate of 5% compounded semi-annually is equivalent to a nominal interest rate of 5% divided by 2, or 2.5% per compounding period.
Now, let's calculate the number of compounding periods for 6 years. There are 4 quarters in a year, so 6 years is equivalent to 6 x 4 = 24 quarters.
Using the formula for present value of an ordinary annuity, we can calculate the amount you need to set aside:
PV = P * (1 - (1 + r)^(-n)) / r
Where:
PV = Present Value
P = Payment per period ($2,000)
r = Interest rate per period (2.5%)
n = Number of compounding periods (24)
PV = $2,000 * (1 - (1 + 0.025)^(-24)) / 0.025
PV = $2,000 * (1 - 0.503212) / 0.025
PV = $2,000 * 0.496788 / 0.025
PV ≈ $39,742.72
Therefore, you would need to set aside approximately $39,742.72 from your lottery winnings to receive $2,000 at the end of every 3 months for 6 years, assuming a 5% interest rate compounded semi-annually.
Learn more about present value calculations :
https://brainly.com/question/29392232
#SPJ11
Define the following terms according to their usage in discrete structures:
argument
premise
conclusion
syllogism
fallacy
contraposition
contradiction
proof by cases
proof by counter example
induction
Write an example of each of the following:
modus ponens
modus tollens
disjunctive syllogism
hypothetical syllogism
addition
simplification
disjunction
resolution
generalization
constructive or destructive dillemma
The terms in discrete structures are defined as follows:
1.Argument: A set of statements where one or more statements (premises) are used to support another statement (conclusion).
2.Premise: A statement or proposition that serves as evidence or support for a conclusion in an argument.
3.Conclusion: The statement that is supported or inferred from the premises in an argument.
4.Syllogism: A form of deductive reasoning that consists of two premises and a conclusion, following a specific logical structure.
5.Fallacy: An error in reasoning that leads to an invalid or unsound argument.
6.Contraposition: A logical inference that involves negating and reversing the terms of a conditional statement.
7.Contradiction: A statement or proposition that is opposite or negates another statement, leading to a logical inconsistency.
8.Proof by cases: A method of proof where all possible cases or scenarios are examined to establish the truth of a statement.
9.Proof by counterexample: A method of disproving a statement by providing a specific example that contradicts it.
10.Induction: A form of reasoning that involves making generalizations or drawing conclusions based on specific instances or observations.
1.Modus ponens: If A, then B. A is true, therefore B is true.
Example: If it is raining, then the ground is wet. It is raining. Therefore, the ground is wet.
2.Modus tollens: If A, then B. Not B is true, therefore not A is true.
Example: If it is a weekday, then I go to work. I am not going to work. Therefore, it is not a weekday.
3.Disjunctive syllogism: A or B. Not A is true, therefore B is true.
Example: It is either sunny or cloudy. It is not sunny. Therefore, it must be cloudy.
4.Hypothetical syllogism: If A, then B. If B, then C. Therefore, if A, then C.
Example: If it rains, then the ground is wet. If the ground is wet, then it is slippery. Therefore, if it rains, it is slippery.
5.Addition: A. Therefore, A or B.
Example: It is raining. Therefore, it is raining or the sun is shining.
6.Simplification: A and B. Therefore, A.
Example: The car is red and it is parked. Therefore, the car is red.
7.Disjunction: A or B. Therefore, B or A.
Example: It is either Monday or Tuesday. Therefore, it is either Tuesday or Monday.
8.Resolution: (A or B) and (not B or C). Therefore, A or C.
Example: It is either raining or snowing, and it is not snowing or it is cold. Therefore, it is either raining or it is cold.
9.Generalization: A specific statement is true for a particular case, therefore it is true for all cases.
Example: I have seen five black cats, and they were all friendly. Therefore, all black cats are friendly.
10.Constructive or destructive dilemma: If A, then B. If C, then D. A or C is true. Therefore, B or D is true.
Example: If it is sunny, then I will go swimming. If it is cloudy, then I will go hiking. It is either sunny or cloudy. Therefore, I will either go swimming or hiking.
To learn more about Syllogism visit:
brainly.com/question/361872
#SPJ11
1) [A] Determine the factor of safety of the assumed failure surface in the embankment shown in the figure using simplified method of slices (the figure is not drawn to a scale). The water table is located 3m below the embankment surface level, the surface surcharge load is 12 KPa. Soil properties are: Foundation sand: Unit weight above water 18.87 KN/m Saturated unit weight below water 19.24 KN/m Angle of internal friction 289 Effective angle of internal friction 31° Clay: Saturated unit weight 15.72 KN/m Undrained shear strength 12 KPa The angle of internal friction 0° Embankment silty sand Unit weight above water 19.17 KN/m Saturated unit weight below water 19.64 KN/m The angle of internal friction 22° Effective angle of internal friction 26° Cohesion 16 KPa Effective cohesion 10 KPa Deep Sand & Gravel Unit weight above water 19.87 KN/m Saturated unit weight below water 20.24 KN/m The angle of internal friction 34° Effective angle of internal friction 36°
To determine the factor of safety of the assumed failure surface in the embankment, we will use the simplified method of slices. Let's break down the steps:
1. Identify the different soil layers involved in the embankment:
- Foundation sand:
- Unit weight above water: 18.87 kN/m³
- Saturated unit weight below water: 19.24 kN/m³
- Angle of internal friction: 28°
- Effective angle of internal friction: 31°
- Clay:
- Saturated unit weight: 15.72 kN/m³
- Undrained shear strength: 12 kPa
- Angle of internal friction: 0°
- Embankment silty sand:
- Unit weight above water: 19.17 kN/m³
- Saturated unit weight below water: 19.64 kN/m³
- Angle of internal friction: 22°
- Effective angle of internal friction: 26°
- Cohesion: 16 kPa
- Effective cohesion: 10 kPa
- Deep Sand & Gravel:
- Unit weight above water: 19.87 kN/m³
- Saturated unit weight below water: 20.24 kN/m³
- Angle of internal friction: 34°
- Effective angle of internal friction: 36°
2. Determine the height of the embankment above the water table:
- The water table is located 3m below the embankment surface level.
3. Calculate the total stresses acting on the assumed failure surface in the embankment:
- Consider the unit weights and surcharge load of each soil layer above the failure surface.
4. Calculate the pore water pressure at the failure surface:
- The saturated unit weight of each soil layer below the water table is relevant in this calculation.
5. Determine the effective stresses acting on the failure surface:
- Subtract the pore water pressure from the total stresses.
6. Calculate the shear strength along the failure surface:
- For each soil layer, consider the cohesion (if applicable) and the effective angle of internal friction.
7. Compute the factor of safety:
- Divide the sum of the resisting forces (shear strength) by the sum of the driving forces (shear stress).
Please note that to provide a specific factor of safety calculation, the exact geometry and dimensions of the embankment and failure surface are needed. This answer provides a general outline of the steps involved in determining the factor of safety using the simplified method of slices.
To know more about embankment : https://brainly.com/question/1851822
#SPJ11
round √30 to two decimal places.
i need help asap pls
Answer:
5.48
Step-by-step explanation:
√30 = 5.4772255... (using a calculator)
√30 = 5.48
What is bleeding of concrete and are the factors effecting the bleeding.
Bleeding of concrete refers to the process where water rises to the surface of freshly poured concrete. It occurs due to the settlement of solid particles within the concrete mixture, causing water to separate and migrate upwards. This can result in a layer of water forming on the surface, which can lead to various issues if not properly managed.
Several factors can affect the bleeding of concrete:
1. Water-cement ratio: The amount of water in the concrete mixture relative to the amount of cement greatly influences bleeding. Higher water-cement ratios increase the likelihood of bleeding, as there is more free water available to separate and rise to the surface.
2. Aggregate properties: The type, shape, and size of aggregates used in the concrete mixture can impact bleeding. Rounded or smooth aggregates tend to increase bleeding, while angular or rough aggregates can help reduce it.
3. Concrete mixture consistency: The consistency or workability of the concrete mixture affects bleeding. Mixtures with higher workability are more prone to bleeding as they have higher water content and increased flowability.
4. Admixtures: Certain admixtures, such as water-reducing agents, can modify the rheological properties of concrete and impact bleeding. These admixtures can either increase or decrease bleeding, depending on their specific characteristics and dosage.
5. Concrete temperature: The temperature of the concrete during placement and curing can influence bleeding. Higher temperatures accelerate the hydration process, leading to faster bleeding, while lower temperatures can slow down bleeding.
Learn more about concrete:
https://brainly.com/question/15291235
#SPJ11
Which statements below are correct regarding intermolecular forces? 1. Hydrogen bonding is the strongest intermolecular force 2. Larger molecules will have weaker intermolecular forces 3. A phase change from gas to liquid results in the release of thermal energy 4. Dipole-induced dipole forces are stronger than ion-induced dipole forces 6. A phase change from a gas to a solid requires the same amount of energy as the sum of a phase change from gas phase to liquid phase and liquid phase to solid phase 7. A phase change from a liquid phase to a gas phase requires some of the inputted thermal enetgy to be lost as work 3. A liquid will only increase its rate of evaporation if the temperature is increased a. 1,3,5,6 b. 1,2,3,4,6 c. 3,7 d. none of the above choices is correct 8,2
Intermolecular forces refer to the attractive forces that occur between molecules. These forces hold molecules together in the liquid and solid phases, and they are responsible for the physical properties of substances. the statements that are correct regarding intermolecular forces are 1, 2, 3, 6, and 8. So, the answer is option (b) 1,2,3,4,6.
The statements that are correct regarding intermolecular forces are:1. Hydrogen bonding is the strongest intermolecular force. It is an intermolecular force that occurs in molecules that have hydrogen atoms bonded to highly electronegative atoms such as nitrogen, oxygen, or fluorine.2. Larger molecules will have weaker intermolecular forces. The size of a molecule has an effect on its intermolecular forces. The larger the molecule, the greater the distance between the molecules, and the weaker the intermolecular forces.3. A phase change from gas to liquid results in the release of thermal energy.
When a gas changes to a liquid, it loses energy, which is released as thermal energy.6. A phase change from a gas to a solid requires the same amount of energy as the sum of a phase change from gas phase to liquid phase and liquid phase to solid phase. The amount of energy required for a phase change depends on the nature of the substance, not on the direction of the change.7. A phase change from a liquid phase to a gas phase requires some of the inputted thermal energy to be lost as work. When a liquid changes to a gas, it needs energy, which is taken from the surroundings, so the temperature decreases.8.
A liquid will only increase its rate of evaporation if the temperature is increased. Increasing the temperature of a liquid increases the kinetic energy of the molecules, causing them to move faster and escape the surface of the liquid more frequently. Hence, the statements that are correct regarding intermolecular forces are 1, 2, 3, 6, and 8. So, the answer is option (b) 1,2,3,4,6.
For more information on Intermolecular forces visit:
brainly.com/question/9328418
#SPJ11
which of the following property describes the colligative property of a solution?A) a solution property that depends on the identity of the solute particles present B) a solution property that depends on the electrical charges of the solute particles present C) a solution property that depends on the concentration of solute particle present D) a solution property that depends on the pressure of the solute particles present
C) a solution property that depends on the concentration of solute particle present. is the correct option. The solution property that depends on the concentration of solute particle present is called the colligative property of a solution.
What are colligative properties? Colligative properties of solutions are physical properties that depend only on the number of solute particles dissolved in a solvent and not on their identity. Colligative properties include boiling point elevation, freezing point depression, vapor pressure reduction, and osmotic pressure.
For example, consider two aqueous solutions, one containing a mole of sucrose and the other containing a mole of sodium chloride. The NaCl solution has twice the number of solute particles as the sucrose solution. The colligative properties of the NaCl solution will be twice as much as the sucrose solution.
To know more about colligative property visit:
brainly.com/question/10679230
#SPJ11
a) Find the missing properties of water by making use of data tables: b) Sketch T-v diagram and locate the systems (A, B, C, D) on it.
The following are the missing properties of water: Boiling point at atmospheric pressure: 100°Critical pressure: 220.6 barsSpecific heat capacity: 4.18 J/gKb) .
The T-v diagram with the systems (A, B, C, D) on it is as follows:System A: superheated steam (dry)System B: saturated steamSystem C: wet steam System D: compressed liquid waterThe T-v diagram of water is shown below.
In this diagram, the lines that divide the water states are called the saturation curve and the critical point is located at the end of the curve.Wet steam can be found on the left of the curve and dry or superheated steam can be found on the right of the curve.
To know more about pressure visit :
https://brainly.com/question/29341536
#SPJ11
DIFFERENTIAL EQUATIONS PROOF: Find a 1-parameter family of solutions for f ' (x) = f (-x)
The 1-parameter family of solutions for the differential equation f'(x) = f(-x) is f(x) = F(x) + C.
Given a differential equation:
f'(x) = f(-x)
It is required to find the 1-parameter family of solutions for the given differential equation.
First, find the integral of the given differentiation equation.
Integrate both sides.
∫ f'(x) dx = ∫ f(-x) dx
It is known that ∫ f'(x) dx is equal to f(x).
So the equation becomes:
f(x) = ∫ f(-x) dx
f(x) = F(x) + C
where, F(x) = ∫ f(-x) dx, if f(x) is an odd function and F(x) = ∫ f(x) dx when f(x) is even function.
Learn more about Differential Equations here :
https://brainly.com/question/33466735
#SPJ4
Which one of the following points does not belong to the graph of the circle: (x−3) ^2+(y+2) ^2 =25 ? A) (8,−2) B) (3,3) C) (3,−7) D) (0,2) E) (−2,−3)
The point that does not belong to the graph of the circle is E) (-2, -3).
To determine which point does not belong to the graph of the circle given by the equation [tex]\((x-3)^2 + (y+2)^2 = 25\),[/tex]we can substitute the coordinates of each point into the equation and check if it satisfies the equation.
Let's go through each option:
A) (8, -2):
Substituting the values, we get:
[tex]=\((8-3)^2 + (-2+2)^2 \\=25\)\(5^2 + 0^2 \\= 25\)\(25 + 0 \\= 25\)\\[/tex]
The point (8, -2) satisfies the equation.
B) (3, 3):
Substituting the values, we get:
[tex]=\((3-3)^2 + (3+2)^2 \\= 25\)\(0^2 + 5^2 \\= 25\)\(0 + 25 \\= 25\)[/tex]
The point (3, 3) satisfies the equation.
C) (3, -7):
Substituting the values, we get:
[tex]=\((3-3)^2 + (-7+2)^2 \\= 25\)\(0^2 + (-5)^2 \\= 25\)\(0 + 25 \\= 25\)\\[/tex]
The point (3, -7) satisfies the equation.
D) (0, 2):
Substituting the values, we get:
[tex]=\((0-3)^2 + (2+2)^2 \\= 25\)\((-3)^2 + 4^2 \\= 25\)\(9 + 16 \\= 25\)[/tex]
The point (0, 2) satisfies the equation.
E) (-2, -3):
Substituting the values, we get:
[tex]=\((-2-3)^2 + (-3+2)^2 \\= 25\)\((-5)^2 + (-1)^2 \\= 25\)\(25 + 1 \\= 26\)\\[/tex]
The point (-2, -3) does not satisfy the equation.
Therefore, the point that does not belong to the graph of the circle is E) (-2, -3).
To know more about equation click-
http://brainly.com/question/2972832
#SPJ11
A steel rod having a cross-sectional area of 332 mm^2 and a length of 169 m is suspended vertically from one end. The unit mass of steel is 7950 kg/m3 and E = 200x (10^3) MN/m2. Find the maximum tensile load in kN that the rod can support at the lower end if the total elongation should not exceed 65 mm.
Maximum tensile load: 4.67 kN . The cross-sectional area of the steel rod is 332 mm^2, which is equivalent to 0.332x10^-3 m^2. The length of the rod is 169 m.
The unit mass of steel is 7950 kg/m^3, and E (Young's modulus) is 200x10^3 MN/m^2. To find the maximum tensile load, we need to consider the elongation of the rod. Given that the total elongation should not exceed 65 mm (0.065 m), we can use Hooke's law:
Stress = Young's modulus × Strain
Since stress is force divided by area, and strain is the ratio of elongation to original length, we can rearrange the equation:
Force = Stress × Area × Length / Elongation
Substituting the given values:
Force = (200x10^3 MN/m^2) × (0.332x10^-3 m^2) × (169 m) / (0.065 m)
≈ 4.67 kN .
The steel rod can support a maximum tensile load of approximately 4.67 kN at the lower end, considering that the total elongation should not exceed 65 mm.
To know more about tensile visit:
https://brainly.com/question/14293634
#SPJ11
Use two-point, extrapolation linear interpolation or of the concentrations obtained for t = 0 and t = 1.00 min, in order to estimate the concentration at t = 0.500 min. Estimate: C = i mol/L Calculate the actual concentration at t = 0.500 min using the exponential expression. C = i mol/L
The concentration of a substance can be predicted by using two-point, extrapolation, linear interpolation, or other methods.
The substance's concentration can be estimated by using these methods for t = 0 and t = 1.00 min and then used to estimate the concentration at t = 0.500 min. A reliable estimate is necessary to ensure that the substances are used appropriately in chemical reactions.
To calculate the concentration of a substance at time t = 0.500 min, we may use two-point extrapolation or linear interpolation. Using these methods, the concentration of a substance at t = 0 and t = 1.00 min is calculated first. Linear interpolation is used to estimate the substance's concentration at time t = 0.500 min.
Exponential expressions can be used to determine the substance's actual concentration at t = 0.500 min.The concentration of a substance is calculated using two-point extrapolation by using the initial concentrations at t = 0 and t = 1.00 min. The average change in concentration is then calculated.
The result is the concentration at t = 0.500 min. Linear interpolation can be used to estimate the substance's concentration at time t = 0.500 min.
Linear interpolation is a simple method for determining the concentration of a substance between two time points.To estimate the concentration of a substance at t = 0.500 min, we must use the following equation:
C = C0[tex]e^(-kt)[/tex] Where C is the concentration of the substance, C0 is the initial concentration of the substance, k is the rate constant, and t is the time.
The concentration of the substance can be calculated by solving the equation for C. The concentration of the substance at t = 0.500 min can be calculated by plugging in the value of t into the equation and solving for C.
In conclusion, we can estimate the concentration of a substance at t = 0.500 min by using two-point extrapolation or linear interpolation. The exponential expression is used to calculate the actual concentration of the substance at t = 0.500 min. The concentration of a substance is a crucial factor in chemical reactions. A reliable estimate of the concentration of a substance is necessary to ensure that the reaction occurs as intended.
To know more about extrapolation visit:
brainly.com/question/33244995
#SPJ11
When the following equation is balanced properly under acidic conditions, what are the coefficients of the species shown? Mg2+ Cro4² + Water appears in the balanced equation as a product, neither) with a coefficient of How many electrons are transferred in this reaction? Cr3+ Submit Answer + Mg (reactant, (Enter 0 for neither.) Retry Entire Group 9 more group attempts remaining q When the following equation is balanced properly under acidic conditions, what are the coefficients of the species shown? Cr3+ CIO3 + Water appears in the balanced equation as a product, neither) with a coefficient of How many electrons are transferred in this reaction?
The coefficients of the species in the balanced equation are:
- Mg2+: 1
- CrO4²-: 1
- H2O: 4
- H+: 8
When balancing an equation under acidic conditions, we need to make sure that the number of atoms of each element is the same on both sides of the equation.
For the equation:
Mg2+ + CrO4²- + H2O → (product)
To balance this equation, we need to determine the coefficients of each species. Let's go step by step:
1. Start by balancing the atoms other than hydrogen and oxygen. In this case, we have one magnesium ion (Mg2+) and one chromate ion (CrO4²-) on the left side of the equation. To balance these, we need to put a coefficient of 1 in front of each species:
Mg2+ + CrO4²- + H2O → (product)
2. Now let's balance the oxygen atoms. On the left side, there are four oxygen atoms in the chromate ion, so we need four water molecules (H2O) on the right side to balance the oxygen:
Mg2+ + CrO4²- + 4H2O → (product)
3. Finally, let's balance the hydrogen atoms. On the right side, we have 8 hydrogen atoms from the 4 water molecules. To balance this, we need to add 8 hydrogen ions (H+) on the left side:
Mg2+ + CrO4²- + 4H2O → (product) + 8H+
The coefficients of the species in the balanced equation are:
- Mg2+: 1
- CrO4²-: 1
- H2O: 4
- H+: 8
Now, moving on to the second part of the question, the number of electrons transferred in this reaction can be determined by looking at the change in oxidation states of the elements involved. However, the equation provided is incomplete, as there is no reactant specified. Therefore, it is not possible to determine the number of electrons transferred in this reaction without additional information.
Learn more about coefficients of the species :
https://brainly.com/question/1038771
#SPJ11
Find volume of a solid bounded above the sphere x² + y² +(2-1)² = 1 and below the sphere x² + y² + z² = 1.
The first sphere is defined by the equation x² + y² + (2-1)² = 1, and the second sphere is defined by the equation x² + y² + z² = 1. the volume of the solid is zero. The volume of a solid bounded above by a specific sphere and below by another sphere.
The volume of the solid bounded above the sphere x² + y² + (2-1)² = 1 and below the sphere x² + y² + z² = 1, we need to determine the region of intersection between the two spheres and calculate its volume.
The first sphere can be written as:
x² + y² + 1 = 1
x² + y² = 0
This equation represents a single point at the origin (0, 0) in the xy-plane.
The second sphere is x² + y² + z² = 1, which is the equation of a standard unit sphere centered at the origin.
Since the first sphere only represents a single point, the intersection between the two spheres is also a single point at the origin.
Therefore, the volume of the solid bounded above the first sphere and below the second sphere is zero since there is no region of intersection between them., the volume of the solid is zero.
Learn more about sphere:
https://brainly.com/question/15044609
#SPJ11
a) Explain the main differences between combustion, gasification and pyrolysis technologies? Identify 3 main differences and briefly explain them. (no need to present detailed parameters) b) For landfill waste management, what are the main problems posed by the wastes in terms of high water content, and high organic content. c) which management method (thermal treatment vs landfill) is suitable for explosive/radiative hazardous waste?
Waste management involves the collection, transportation, processing, and disposal of waste in a manner that is environmentally and socially responsible.
Combustion: Combustion is a process that involves the burning of a fuel in the presence of oxygen. It typically involves the complete oxidation of the fuel, resulting in the release of heat and the formation of combustion products such as carbon dioxide and water vapor. The main differences with gasification and pyrolysis are:
Combustion relies on the supply of oxygen to burn the fuel completely, whereas gasification and pyrolysis can occur in the absence or limited presence of oxygen.Combustion generally produces heat and energy as the primary outputs, while gasification and pyrolysis can produce a variety of outputs, including synthesis gas (syngas) in gasification and biochar in pyrolysis.Combustion is typically used for energy generation, such as in power plants or heating systems, while gasification and pyrolysis are often utilized for waste treatment, biofuel production, or chemical synthesis.For landfill waste management, the high water content and high organic content of the wastes pose significant problems:
High water content: Landfill waste with high water content can lead to the production of leachate, which is a highly polluting liquid that can contaminate groundwater and surface water. It requires careful management and treatment to prevent environmental contamination. The leachate contains various pollutants, including heavy metals, organic compounds, and pathogens, which can have detrimental effects on ecosystems and human health.High organic content: Landfill waste with high organic content contributes to the production of methane gas, a potent greenhouse gas that significantly contributes to climate change. Methane has a much higher global warming potential than carbon dioxide. Landfills are one of the largest human-made sources of methane emissions globally. To mitigate this issue, landfill operators often implement gas collection systems to capture and utilize methane as an energy source.
Thermal treatment methods, such as incineration, are typically more suitable for explosive or radiative hazardous waste. Incineration involves controlled combustion at high temperatures, which can effectively destroy hazardous substances and reduce them to less harmful compounds or ash. This process can handle hazardous waste materials that may contain explosive or radiative components, ensuring their safe disposal. Landfilling, on the other hand, is generally not suitable for explosive or radiative hazardous waste as it does not provide the necessary level of containment and control for these types of materials. Landfills are primarily designed for non-hazardous waste disposal and are subject to regulations and restrictions regarding the acceptance of hazardous materials.
learn more about Waste Management.
brainly.com/question/1396689
#SPJ11
Write the amino acid sequence of the polypeptide that is synthesized if the top of the DNA is a coding strand (N-terminal amino acids on the left and C-terminal amino acids on the right)| 3'-TGGTAATTTTACAGTCGGGTACGTAGTTCACTAGATCCA-5' 5'-ACCATTAAAATGTCAGCCCATGCATCAAGTGATCTAGGT-3'
When we read the DNA sequence in the 5’ to 3’ direction, we get the messenger RNA. The DNA sequence given is the coding strand, and we will use it to obtain the mRNA sequence.
Using the given DNA sequence, the mRNA will be:
5’-ACCAUUAAA AUGUCAG CCCAUGCAUCAAGUGAUCUAGGU-3’
Now, we can use the codon chart to obtain the amino acid sequence from the mRNA sequence.
Codon Chart:
UUU, UUC – Phenylalanine (Phe)
UUA, UUG – Leucine (Leu)
UCU, UCC, UCA, UCG – Serine (Ser)
UAU, UAC – Tyrosine (Tyr)
UAA, UAG, UGA – Stop
UGU, UGC – Cysteine (Cys)
UGG – Tryptophan (Trp)
CGU, CGC, CGA, CGG – Arginine (Arg)
CCU, CCC, CCA, CCG – Proline (Pro)
CAU, CAC – Histidine (His)
CAA, CAG – Glutamine (Gln)
CGU, CGC, CGA, CGG – Arginine (Arg)
AUU, AUC, AUA – Isoleucine (Ile)
AUG – Methionine (Met)
ACU, ACC, ACA, ACG – Threonine (Thr)
AAU, AAC – Asparagine (Asn)
AAA, AAG – Lysine (Lys)
AGU, AGC – Serine (Ser)
AGA, AGG – Arginine (Arg)
GUU, GUC, GUA, GUG – Valine (Val)
GCU, GCC, GCA, GCG – Alanine (Ala)
GAU, GAC – Aspartic Acid (Asp)
GAA, GAG – Glutamic Acid (Glu)
GGU, GGC, GGA, GGG – Glycine (Gly)
So, the amino acid sequence of the polypeptide will be:
Met-Phe-Lys-Cys-Pro-Cys-His-Gln-Val-Stop.
Learn more about amino acid:
brainly.com/question/31608774
#SPJ11
A solid steel shaft is to be used to transmit 3,750 W from the motor to which it is attached. The shaft rotates at 175 rpm(rev/min). Determine the required diameter of the shaft to the nearest mm if the shaft has an allowable shearing stress of 100 MPa. Select one: O a. 32 mm O b. 25 mm O c. 36 mm O d. 22 mm
To transmit 3,750 W at 175 rpm with an allowable shearing stress of 100 MPa, the required diameter of the solid steel shaft, rounded to the nearest mm, is 32 mm.
Determine the torque (T) using the formula T = (P * 60) / (2 * π * N), where P is the power (in watts) and N is the rotational speed (in rev/min).
Calculate the shear stress (τ) using the formula τ = (16 * T) / (π * d^3), where d is the diameter of the shaft.
Rearrange the shear stress formula to solve for the diameter (d), considering the given shear stress limit (100 MPa).
Substitute the calculated torque and shear stress limit into the equation to find the required diameter of the solid steel shaft.
Round the diameter to the nearest mm, yielding the answer of 32 mm.
To know more about diameter visit:
https://brainly.com/question/32968193
#SPJ11
Consider a two-stage cascade refrigeration system operating between -50°C and 50°C. Each stage operates on an ideal vapor-compression refrigeration cycle. The upper cycle uses ammonia as working fluid; lower cycle uses R-410a. In the lower cycle refrigerant condenses at -10°C, in the upper cycle refrigerant evaporates at 0°C. If the mass flow rate in the upper cycle is 0.5 kg/s, determine the following: a.) the mass flow rate through the lower cycle: kg/s b.) the rate of cooling in tons: c.) the rate of heat removed from the cycle: d.) the compressors power input in kW: e.) the coefficient of performance: KW
The calculations involve determining the mass flow rates, cooling rate, heat removal rate, compressor power input, and coefficient of performance (COP).
What are the key calculations and parameters involved in analyzing a two-stage cascade refrigeration system?a) The mass flow rate through the lower cycle can be determined using the principle of conservation of mass. Since the upper cycle mass flow rate is given as 0.5 kg/s, we can assume that the mass flow rate through the lower cycle is also 0.5 kg/s.
b) The rate of cooling in tons can be calculated by dividing the heat removed from the cycle by the refrigeration effect. Since the refrigeration effect is given by the mass flow rate through the upper cycle multiplied by the enthalpy change between the evaporator and the condenser, we need additional information to calculate the rate of cooling in tons.
c) The rate of heat removed from the cycle can be calculated by multiplying the mass flow rate through the upper cycle by the specific heat capacity of the working fluid and the temperature difference between the evaporator and the condenser.
d) The compressor's power input in kW can be determined using the equation: power = mass flow rate through the upper cycle multiplied by the specific enthalpy increase across the compressor.
e) The coefficient of performance (COP) is the ratio of the rate of cooling to the compressor's power input. It can be calculated by dividing the rate of cooling in tons by the power input in kW.
For a more accurate calculation, specific values for enthalpies, specific heat capacities, and refrigeration effect are required.
Learn more about mass flow rates
brainly.com/question/30763861
#SPJ11
construct triangle xyz mXY=4.5cm mYZ=3.4cm mZX=5.6cm
draw one altitude from X to YZ
In this problem, p is in dollars and x is the number of units. The demand function for a product is p=100/ (x+4) If the equilibrium quantity is 6 units, what is the equilibrium price? P1= What is the equilibrium point? (x1,p1)=() What is the consumer's surplus? (Round your answer to the nearest cent.) $
The equilibrium price (p1) is $10.
The equilibrium point is (6, 10).
The consumer surplus, rounded to the nearest cent, is approximately $69.31.
Exp:
To find the equilibrium price and equilibrium point, we can set the quantity demanded equal to the quantity supplied.
The demand function is given by:
p = 100 / (x + 4)
At equilibrium, the quantity demanded (x) is equal to the equilibrium quantity (6 units).
Substituting x = 6 into the demand function, we can solve for the equilibrium price (p1):
p1 = 100 / (6 + 4)
p1 = 100 / 10
p1 = 10
Therefore, the equilibrium price (p1) is $10.
To find the equilibrium point (x1, p1), we substitute the equilibrium quantity and price into the demand function:
x1 = 6
p1 = 10
So, the equilibrium point is (6, 10).
Consumer surplus represents the additional benefit or value that consumers receive when they pay a price lower than what they are willing to pay.
It can be calculated by finding the area between the demand curve and the equilibrium price.
To calculate the consumer surplus, we first need to find the area under the demand curve up to the equilibrium quantity. The demand function is given by:
p = 100 / (x + 4)
Integrating the demand function with respect to x from 0 to 6 (equilibrium quantity), we can find the area:
CS = ∫[0 to 6] (100 / (x + 4)) dx
Evaluating the integral:
CS = [100 ln(x + 4)] from 0 to 6
CS = 100 ln(6 + 4) - 100 ln(0 + 4)
CS = 100 ln(10) - 100 ln(4)
Using a calculator, we can find the numerical value of the consumer surplus:
CS ≈ $69.31
Therefore, the consumer surplus, rounded to the nearest cent, is approximately $69.31.
Learn more about consumer surplus from the given link
https://brainly.com/question/13136036
#SPJ11
Q8) The velocity distribution for the flow of a Newtonian fluid between two wide, parallel plates is given by the equation u = (3V/2) [1-(y/h) 2], where V is the mean velocity and the fluid has dynamic viscosity of 0.38 N.s/m² h = 5.0 mm, V = 0.61 m/s. Determine: (a) the shearing stress acting on the bottom wall, and (b) the shearing stress acting on a plane parallel to the walls and passing through the centerline (mid plane).
Previous questionNext question
The velocity distribution for the flow of a Newtonian fluid between two wide, parallel plates is given by the equation u = (3V/2) [1-(y/h)^2], where V is the mean velocity, y is the distance from the bottom plate, and h is the distance between the plates.
To determine the shearing stress acting on the bottom wall (a), we can use the equation for shear stress, which is given by τ = μ(dv/dy), where τ is the shearing stress, μ is the dynamic viscosity, and (dv/dy) is the velocity gradient in the y-direction.
In this case, the velocity gradient can be obtained by differentiating the velocity distribution equation with respect to y.
Let's calculate it step-by-step:
1. Differentiate the velocity distribution equation u = (3V/2) [1-(y/h)^2] with respect to y:
du/dy = (3V/2) * d/dy [1-(y/h)^2]
2. Applying the chain rule, the differentiation of [1-(y/h)^2] with respect to y is:
du/dy = (3V/2) * [-2(y/h)] * (1/h)
3. Simplify the equation:
du/dy = -(3V/h^2) * y
4. Now, substitute the given values into the equation:
du/dy = -(3 * 0.61 / (0.005^2)) * y
5. Calculate the velocity gradient for y = 0 (at the bottom wall):
du/dy = -(3 * 0.61 / (0.005^2)) * 0
Since y = 0 at the bottom wall, the velocity gradient du/dy is equal to 0 at the bottom wall. Therefore, the shearing stress acting on the bottom wall is also 0. To determine the shearing stress acting on a plane parallel to the walls and passing through the centerline (mid plane) (b), we need to calculate the velocity gradient at the mid plane.
Let's calculate it step-by-step:
1. Calculate the distance from the mid plane to the top wall:
Distance from mid plane to top wall = (h/2)
2. Calculate the velocity gradient at the mid plane:
du/dy = -(3 * 0.61 / (0.005^2)) * (h/2)
3. Simplify the equation:
du/dy = -(3 * 0.61 / (0.005^2)) * (h/2)
4. Substitute the given value of h:
du/dy = -(3 * 0.61 / (0.005^2)) * (0.005/2)
5. Calculate the shearing stress at the mid-plane:
τ = μ * (du/dy)
Substitute the given value of dynamic viscosity μ into the equation to find the shearing stress at the mid-plane.
Learn more about Velocity:
https://brainly.com/question/80295
#SPJ11