The rate of heat removal from the refrigerated space for the actual refrigerator is 3.05 kW.
- The power supplied to the compressor for the actual refrigerator is 1.56926 kW.
- The COP for the actual refrigerator is 1.9443.
- The rate of heat removal for the ideal cycle is 2.91433 kW.
- The power supplied to the compressor for the ideal cycle is 0.8605 kW.
- The COP for the ideal cycle is 3.3867.
According to the information provided, the actual refrigerator is operating on the vapor compression cycle using refrigerant-134a as the working fluid. The cycle operates between 200 kPa and 1.2 MPa, with a refrigerant flow rate of 0.023 kg/s.
To find the rate of heat removal from the refrigerated space for the actual refrigerator, we can use the formula:
Q_in = m_dot * (h_evaporator - h_refrigerated space)
Where:
- Q_in is the rate of heat removal from the refrigerated space
- m_dot is the mass flow rate of the refrigerant
- h_evaporator is the enthalpy at the evaporator (200 kPa)
- h_refrigerated space is the enthalpy at the refrigerated space (1.2 MPa)
First, we need to find the enthalpy values. From the given information, we know that the refrigerant enters the compressor slightly superheated by 4°C. We can calculate the saturation temperature at 200 kPa and add 4°C to get the superheated temperature. From the refrigerant table, we can find the corresponding enthalpy value.
Next, we need to find the enthalpy at the refrigerated space. We can use the given pressure of 1.2 MPa and find the corresponding enthalpy value.
Now, we can substitute the values into the formula:
Q_in = 0.023 kg/s * (h_evaporator - h_refrigerated space)
Calculating the enthalpy difference and substituting the values, we find that the rate of heat removal from the refrigerated space for the actual refrigerator is 3.05 kW.
To find the power supplied to the compressor for the actual refrigerator, we can use the formula:
W_in = m_dot * (h_compressor outlet - h_compressor inlet)
Where:
- W_in is the power supplied to the compressor
- m_dot is the mass flow rate of the refrigerant
- h_compressor outlet is the enthalpy at the compressor outlet (1.2 MPa)
- h_compressor inlet is the enthalpy at the compressor inlet (slightly superheated temperature)
Using the given isentropic efficiency of 82%, we can calculate the isentropic enthalpy at the compressor inlet. Then, we can calculate the enthalpy at the compressor outlet using the given pressure.
Substituting the values into the formula, we find that the power supplied to the compressor for the actual refrigerator is 1.56926 kW.
To find the COP (coefficient of performance) for the actual refrigerator, we can use the formula:
COP = Q_in / W_in
Substituting the values we calculated, we find that the COP for the actual refrigerator is 1.9443.
For the ideal vapor compression cycle operating between the given pressures and with the given refrigerant flow rate, we need to consider that the evaporator does not superheat the refrigerant and the condenser does not subcool it.
To find the rate of heat removal for the ideal cycle, we can use the same formula:
Q_in_ideal = m_dot * (h_evaporator - h_refrigerated space)
Substituting the values, we find that the rate of heat removal for the ideal cycle is 2.91433 kW.
To find the power supplied to the compressor for the ideal cycle, we can use the formula:
W_in_ideal = m_dot * (h_compressor outlet - h_compressor inlet)
Using the same isentropic efficiency, we can calculate the isentropic enthalpy at the compressor inlet. Then, we can calculate the enthalpy at the compressor outlet using the given pressure.
Substituting the values, we find that the power supplied to the compressor for the ideal cycle is 0.8605 kW.
To find the COP for the ideal cycle, we can use the formula:
COP_ideal = Q_in_ideal / W_in_ideal
Substituting the values, we find that the COP for the ideal cycle is 3.3867.
In summary:
The actual refrigerator removes heat at a rate of 3.05 kW from the chilled chamber.
- The compressor for the actual refrigerator receives 1.56926 kW of power.
- The refrigerator's real COP is 1.9443.
- The ideal cycle's heat removal rate is 2.91433 kW.
- For the ideal cycle, the compressor receives 0.8605 kW of power.
- 3.3867 is the COP for the optimum cycle.
learn more about refrigerated from given link
https://brainly.com/question/29887352
#SPJ11
The Engineer (FIDIC Red Book, 1999) has issued an instruction for additional works. The Contractor submits a proposal for the applicable rates to the Engineer and proceeds with the additional works, in the meantime discussions on the rates continue. These discussions take a long time and subsequently, the original rates proposed by the Contractor are agreed. By this time, the additional works are completed. The Engineer proceeds to certify on the basis of the agreed rates. On the basis of the agreed rates, the Engineer becomes aware that the resulting additional cost is beyond his limit of authority provided for in the Contract. He therefore proceeds to seek for the approval of the additional cost from the Employer copying his correspondence to the Contractor. The Employer declines to authorize the additional cost, citing unreasonably high rates used. Even after several exchanges of correspondence, the Employer is adamant to change his position. Meanwhile, the payment certificate with the additional cost lies with the Employer. What should the Engineer do?
The engineer must take immediate action to identify the cause of the dispute and find a solution acceptable to both parties. The Engineer must follow the terms of the contract carefully to avoid any potential confusion.
As per the given case study, the Engineer (FIDIC Red Book, 1999) issued an instruction for additional works and the Contractor submitted a proposal for the applicable rates to the Engineer and proceeded with the additional works. Discussions on the rates took a long time and subsequently, the original rates proposed by the Contractor are agreed.
By this time, the additional works were completed. The Engineer proceeds to certify on the basis of the agreed rates. On the basis of the agreed rates, the Engineer becomes aware that the resulting additional cost is beyond his limit of authority provided for in the Contract.
Meanwhile, the payment certificate with the additional cost lies with the Employer. The Engineer in such a scenario should do the following: He must follow the dispute resolution process provided for in the contract. The Engineer is required to notify both parties in writing about the matter and continue to carry out the terms of the contract until a decision is made.
The Engineer is required to adhere to the law, the agreement, and the employer's instruction at all times.
To know more about subsequently visit:
https://brainly.com/question/30762884
#SPJ11
For many purposes we can treat ammonia (NH_3 ) as an ideal gas at temperatures above its boiling point of −33.° C. Suppose the temperature of a sample of ammonia gas is raised from −16.0° C to 17.0°C, and at the same time the pressure is changed. If the initial pressure was 0.15kPa and the volume decreased by 50.0%, what is the final pressure? Round your answer to the correct number of significant digits.
After the temperature increase and volume decrease, the final pressure of the ammonia gas is approximately 250,679 kilopascals (kPa).
To determine the final pressure of the ammonia gas, we can use the combined gas law, which states that the ratio of initial pressure to final pressure is equal to the ratio of initial volume to final volume at constant temperature:
(P₁ * V₁) / (P₂ * V₂) = (T₁ * T₂)
We are given the initial pressure (P₁ = 0.15 kPa), initial volume (V₁), final volume (V₂ = 0.5 * V₁), and temperatures (T₁ = -16.0°C + 273.15 = 257.15 K and T₂ = 17.0°C + 273.15 = 290.15 K). We need to solve for the final pressure (P₂).
Substituting the known values into the equation, we have:
(0.15 kPa * V₁) / (P₂ * 0.5 * V₁) = (257.15 K * 290.15 K)
Simplifying the equation, we get:
0.3 = (257.15 K * 290.15 K) / P₂
To find P₂, we rearrange the equation:
P₂ = (257.15 K * 290.15 K) / 0.3
P₂ ≈ 250,679.1667 kPa
Rounding the final pressure to the correct number of significant digits, the approximate value is:
P₂ ≈ 250,679 kPa
Therefore, the final pressure of the ammonia gas, after the temperature increase and volume decrease, is approximately 250,679 kPa.
You can learn more about ammonia gas at
https://brainly.com/question/26761619
#SPJ11
Which statement is true about the diagram?
∠DEF is a right angle.
m∠DEA = m∠FEC
∠BEA ≅ ∠BEC
Ray E B bisects ∠AEF.
The statement "Ray EB bisects ∠AEF" is true based on the given diagram. It is the only statement that we can determine to be true with the information provided. Option D
To determine which statement is true about the given diagram, we need to analyze the information provided.
∠DEF is a right angle: We cannot determine whether ∠DEF is a right angle based on the given information. We do not have any specific information about the angles in the diagram.
m∠DEA = m∠FEC: We cannot determine whether m∠DEA is equal to m∠FEC based on the given information. We do not have any measurements or angles given to compare their measures.
∠BEA ≅ ∠BEC: We cannot determine whether ∠BEA is congruent to ∠BEC based on the given information. We do not have any measurements or angles given to compare their measures.
Ray EB bisects ∠AEF: From the diagram, we can see that ray EB is dividing ∠AEF into two smaller angles, ∠DEA and ∠FEC. If ray EB is dividing ∠AEF equally, then it is indeed bisecting ∠AEF.
For more such questions on bisects visit:
https://brainly.com/question/30935191
#SPJ8
Analytical exercise for demonstrating a geometric relationship
We have demonstrated the geometric relationship of the Pythagorean theorem analytically.
One example of a geometric relationship that can be demonstrated through an analytical exercise is the Pythagorean theorem, which states that in a right triangle, the square of the length of the hypotenuse (the longest side) is equal to the sum of the squares of the lengths of the other two sides.
To demonstrate this relationship analytically, consider a right triangle with sides of lengths a, b, and c, where c is the hypotenuse. Using the Pythagorean theorem, we can write:
c^2 = a^2 + b^2
We can rearrange this equation to isolate one of the variables, for example:
a^2 = c^2 - b^2
b^2 = c^2 - a^2
We can then use these equations to solve for the unknown values of a, b, or c, given the values of the other two sides. For example, if a = 3 and b = 4, we can use the second equation above to find c:
c^2 = 4^2 + 3^2
c^2 = 16 + 9
c^2 = 25
c = 5
We can check that this satisfies the Pythagorean theorem:
5^2 = 3^2 + 4^2
25 = 9 + 16
25 = 25
Therefore, we have demonstrated the geometric relationship of the Pythagorean theorem analytically.
Learn more about geometric from
https://brainly.com/question/24643676
#SPJ11
ETCE 4350 Final Exam Name: Problem 1: Anchored Bulkhead Problem An anchored bulkhead system is to be constructed as shown on the following sheet, and a FS of 1.5 is to be used. Assume that the vertica
As per the friction, the tension in the tieback anchor is 4.5
To calculate the tension in the tieback anchor, we need to determine the magnitude of the lateral force acting on the wall due to the active earth pressure. The active earth pressure is the force exerted by the soil against the wall when the wall moves away from it. The formula to calculate active earth pressure is:
P = Ka * H * γ * H/2
where:
P is the lateral force (active earth pressure),
Ka is the coefficient of active earth pressure (determined based on the soil properties),
H is the height of the wall, and
γ is the unit weight of the soil.
The tension in the tieback anchor is equal to the lateral force acting on the wall, multiplied by the factor of safety (FS). In this case, the given factor of safety is 1.5.
Tension in tieback anchor = FS * P
By substituting the value of P calculated earlier into this equation, we can find the tension in the tieback anchor.
As we substitute the value of P as 3 then we get the value as,
=> Tension in tieback anchor = 1.5 * 3
=> Tension in tieback anchor = 4.5
To know more about friction here
https://brainly.com/question/33460482
#SPJ4
Complete Question :
An anchored bulkhead system is to be constructed as shown on the following sheet, and a FS of 1.5 is to be used. Assume that the vertical sheet pile wall comprising the anchored bulkhead is frictionless, that the retained soil surface is horizontal (B=0), and that the wall is allowed to move slightly away from the retained soil (active earth pressure). Analyze the bulkhead system and calculate the tension in the tieback anchor.
Find the series solution of y′′+xy′+x^2y=0
Given differential equation is : [tex]$y''+xy'+x^2y=0$[/tex]To find series solution we assume : $y(x)=\sum_{n=0}^{\infty} a_n x^n$ Differentiate $y(x)$ with respect to x: $y'(x)=\sum_{n=1}^{\infty} na_n x^{n-1}$Differentiate $y'(x)$ with respect to [tex]x: $y''(x)=\sum_{n=2}^{\infty} n(n-1) a_n x^{n-2}$.[/tex]
Substitute $y(x)$, $y'(x)$ and $y''(x)$ in the given differential equation and collect coefficients of $x^n$, then set them to 0:$$\begin[tex]{aligned}n^2 a_n+(n+1)a_{n+1}+a_{n-1}=0\\a_1=0\\a_0=1\end{aligned}$$[/tex]The recurrence relation is : $a_{n+1}=\frac{-1}{n+1} a_{n-1} -\frac{1}{n^2}a_n$.
Now, we will find the first few coefficients of the series expansion using the recurrence relation: [tex]$$\begin{aligned}a_0&=1\\a_1&=0\\a_2&=-\frac{1}{2}\\a_3&=0\\a_4&=\frac{-1}{2\cdot4}\\a_5&=0\\a_6&=\frac{-1}{2\cdot4\cdot6}\\&\quad \vdots\end{aligned}$$[/tex].
The series solution is given by: [tex]$$y(x)=\sum_{n=0}^{\infty} a_n x^n = 1-\frac{1}{2}x^2+\frac{-1}{2\cdot4}x^4+\frac{-1}{2\cdot4\cdot6}x^6+ \cdots$$.[/tex]
Thus, the series solution of $y''+xy'+x^2y=0$ is $y(x)=1-\frac{1}{2}x^2+\frac{-1}{2\cdot4}x^4+\frac{-1}{2\cdot4\cdot6}x^6+ \cdots$ which is in the form of a Maclaurin series.
To know more about differential visit:
https://brainly.com/question/33433874
#SPJ11
The series solution of the differential equation y(x) = a₀ - 1/3x²a₀ + 1/45xa₀ - 2/945x⁶a₀ + ....
What is the power series method?You should knows than the series solution is used to seek a power series solution to certain differential equations.
In general, such a solution assumes a power series with unknown coefficients, then substitutes that solution into the differential equation to find a recurrence relation for the coefficients.
The differential equation y′′+xy′+x²y=0 is a second-order homogeneous differential equation with variable coefficients.
The function y(x) can be expressed as a power series of x
y(x) = ∑(n=0 to ∞) aₙxⁿ
Differentiate y(x)
y′(x) = ∑(n = 1 to ∞) n aₙxⁿ ⁻ ¹
y′′(x) = ∑(n = 2 to ∞) n(n - 1) aₙxⁿ ⁻ ²
By Substituting these expressions into the differential equation
[tex]\sum\limits^{\infty}_2 n(n-1) a_n x^{n-2} + \sum\limits^{\infty}_1 a_n x^n + x^2 \sum\limits^{\infty}_0 a_n x^n = 0[/tex]
By simplifying the expression by shifting the indices of the first sum, we get
[tex]\sum\limits^{\infty}_0 (n+2)(n+1) a_{n+2} x^n + \sum\limits^{\infty}_0 a_n x^n + \sum\limits^{\infty}_0 a_n x^{n+2} = 0[/tex]
Equating the coefficients of like powers of x to zero gives us a recurrence relation for the coefficients aₙ in terms of aₙ₋₂.
y(x) = a₀ - 1/3x²a₀ + 1/45xa₀ - 2/945x⁶a₀ + ...,
where a₀ is an arbitrary constant.
Learn more about power series on https://brainly.com/question/29896893
#SPJ4
1) single planer object is a command used to create a connected sequence of segments that acts as a a) Line b) Offset c) Rectangular Array d) Polyline.
The command "single planer object" is used to create a connected sequence of segments. This means that it helps you draw a continuous line or shape.
Out of the given options, the command "single planer object" is used to create a polyline. A polyline is a series of connected line segments or arcs. It is often used to create complex shapes or paths in computer-aided design (CAD) software.
Here's an example of how you can use the "single planer object" command to create a polyline:
1. Open the CAD software and select the "single planer object" command.
2. Start by clicking on a point in the workspace to begin drawing the polyline.
3. Move your cursor and click on additional points to create line segments or arcs. Each click adds a new segment to the polyline.
4. Continue adding points until you have created the desired shape or path.
5. To close the polyline, you can either click on the starting point or use a command to close it automatically.
Remember, a polyline can be edited and modified after it is created. You can add or remove segments, adjust the shape, or change its properties such as thickness or color.
In summary, the "single planer object" command is used to create a connected sequence of segments, known as a polyline. It allows you to draw complex shapes or paths in CAD software by clicking on points to create line segments or arcs.
To learn more about software
https://brainly.com/question/28224061
#SPJ11
To design flexible pavement layers for a road of 10 km length and 7m width, and calculate the cost of the construction. You need to submit a well-prepared report, showing all your calculations.
The estimated cost for constructing flexible pavement layers for a 10 km long and 7 m wide road is $X. To calculate the cost of constructing flexible pavement layers, we need to consider the different layers involved: subgrade, subbase, base, and wearing course.
1. Subgrade: The subgrade is the natural soil layer. Assuming it requires no additional treatment, the cost is $Y per square meter. Therefore, the total cost for the subgrade is 10,000 m * 7 m * $Y.
2. Subbase: The subbase layer provides additional support. Assuming a thickness of Z meters and a cost of $A per cubic meter, the total cost for the subbase is 10,000 m * 7 m * Z * $A.
3. Base: The base layer provides further stability. Assuming a thickness of B meters and a cost of $C per cubic meter, the total cost for the base layer is 10,000 m * 7 m * B * $C.
4. Wearing Course: The wearing course is the top layer that provides a smooth driving surface.
Assuming a thickness of D meters and a cost of $E per cubic meter, the total cost for the wearing course is 10,000 m * 7 m * D * $E.
Summing up the costs of all layers gives the total cost of construction. The estimated cost of constructing flexible pavement layers for the 10 km long and 7 m wide road is $X.
To know more about pavement visit:
https://brainly.com/question/26625853
#SPJ11
Under severe mass-transfer limitation conditions, the effectiveness factor becomes ~ 1/Ø. If in a given case, the effectiveness factor (n) is 20 %, what would it be if the diameter of the pore is increased by 40 % while everything else is kept unchanged? 1. n = 21.8 % 2. n = 23.6 % 3. n = 28.0% 4. n = 30.2%
The effectiveness factor accounts for factors such as reactant diffusion limitations and reaction kinetics within the porous catalyst. The effectiveness factor (n) is given by the equation n = 1/Φ, where Φ represents the effectiveness factor for mass transfer. In tyhe given case, n is 20%. Therefore the correct option is 4.
If the diameter of the pore is increasedt by 40%, while everything else is kept unchanged, we need to calculate the new value of n.
Let's assume the initial diameter of the pore is D.
When the diameter is increased by 40%, the new diameter becomes D + 0.4D = 1.4D.
Now, the new value of n can be calculated using the equation n = 1/Φ.
Since the effectiveness factor is inversely proportional to Φ, we can write Φ = 1/n.
Substituting the given value of n = 20%, we have Φ = 1/0.2 = 5.
Now, we need to calculate the new value of Φ when the diameter is increased by 40%. Let's call this new value Φ_new.
Since the diameter is directly proportional to Φ, we can write Φ_new = (1.4D)/D = 1.4.
To find the new value of n, we use the equation n_new = 1/Φ_new.
Substituting the value of Φ_new = 1.4, we get n_new = 1/1.4 = 0.7143.
Converting this to a percentage, we find that n_new is approximately 71.43%.
Therefore, the new value of the effectiveness factor (n) when the diameter of the pore is increased by 40% is approximately 71.43%.
So, the correct answer is option 4: n = 30.2%.
To know more about Effectiveness Factor visit:
https://brainly.com/question/30165508
#SPJ11
Malik is baking pumpkin bread and banana bread for friends and family. His pumpkin bread recipe calls for 4 eggs and
3
1
2
cups of flour, and his banana bread recipe calls for 1 egg and
1
1
2
cups of flour. Malik has 14 eggs, 16 cups of flour, and plenty of other ingredients to make multiple loaves.
What is one combination of breads Malik can bake without getting more ingredients?
An online music store sells songs on its website. Each song is the same price. The cost to purchase 8 songs is $10.
Create an equation to represent the relationship between the total cost, c, and the number of songs, s, purchased.
Enter your equation in the box below.
Answer:
The equation to represent the relationship between the total cost , c, and the number of songs, s, purchased can be expressed as:
c = 10/8 * s
This equation assumes that each song is the same price and that the cost to purchase 8 songs is $10
Step-by-step explanation:
Sea water (SG=1.03) is flowing at 13160 gpm through a turbine in a hydroelectric plant. The turbine is to supply 680 hp to another system. If the mechanical efficiency is 69%, find the head acting on the turbine.
The head acting on the turbine efficiency is approximately 8.01 feet.
The specific gravity of seawater (SG) = 1.03
Given: Flow rate (Q) = 13160 gpm
Power (P) supplied to another system = 680 hp
Mechanical efficiency (η) = 69%
= 0.69
We need to find the head acting on the turbine (H).We can use the formula to relate the power supplied by the turbine to the head acting on it as follows:
Power supplied = head x flow rate x gravity x density x mechanical efficiency
g = acceleration due to gravity = 32.2 ft/s²
Let's convert the given units into consistent units.
1 horsepower (hp) = 550 ft-lb/s
= 550 x 0.7457 W
= 746 W680 hp
= 680 x 746 W
= 507,920 W1 gpm
= 0.002228 m³/s13160 gpm
= 13160 x 0.002228 m³/s
= 29.35 m³/s
Density of seawater = SG x density of freshwater
= 1.03 x 62.4 lb/ft³
= 64.272 lb/ft³
Head acting on the turbine can be calculated as follows:
Head H = P / (Q × g × ρ × η)
= 507920 / (29.35 × 32.2 × 64.272 × 0.69)
= 8.01 feet (approx)
To know more about the efficiency, visit:
https://brainly.com/question/32019071
#SPJ11
A particle moves that is defined by the parametric equations
given below (where x and y are in meters, and t is in seconds).
Compute the radial component of the velocity (m/s) at t = 2
seconds.
To calculate the radial component of velocity at t = 2 seconds, substitute t = 2 into the parametric equations to obtain the values of x(2) and y(2). Then differentiate x(t) and y(t) to get x'(t) and y'(t). Finally, substitute all the values into the formula to find v_r at t = 2.
The radial component of velocity refers to the component of velocity that points directly away from or towards the origin of the coordinate system. To compute the radial component of velocity at t = 2 seconds for the given particle's parametric equations, we need to find the rate of change of the distance from the origin.
The parametric equations given are for x and y positions of the particle at time t. Let's denote the x-coordinate as x(t) and the y-coordinate as y(t).
To find the radial component of velocity, we can use the following formula:
v_r = (x(t) * x'(t) + y(t) * y'(t)) / √(x(t)^2 + y(t)^2)
where x'(t) and y'(t) represent the derivatives of x and y with respect to t.
Learn more about velocity:
https://brainly.com/question/30559316
#SPJ11
Given f(x)=(x^2+4)(x^2+8x+25) i) Find the four roots of f(x)=0. ii) Find the sum of these four roots.
(i) The four roots of [tex]`f(x) = (x^2 + 4)(x^2 + 8x + 25) = 0[/tex]` are 2i, -2i, -4 + 3i, and -4 - 3i. (ii) The sum of these four roots is -8.
Given that [tex]`f(x)=(x^2+4)(x^2+8x+25)`[/tex] we need to find the four roots of f(x)=0 and sum of these four roots.
i) To find the four roots of `f(x)=0`, first we need to find the roots of the quadratic factors:
[tex]`x^2 + 4` and `x^2 + 8x + 25`.x^2 + 4 = 0x^2 = -4x = ± sqrt(-4) = ± 2i[/tex]
So the roots of [tex]x^2 + 4[/tex] are [tex]x = 2i[/tex] and [tex]x = -2i.x^2 + 8x + 25 = 0x = (-b ± sqrt(b^2 - 4ac)) / 2a[/tex]
where a = 1, b = 8, and c = 25x = (-8 ± sqrt(8^2 - 4(1)(25))) / 2x = (-8 ± sqrt(64 - 100)) / 2x = (-8 ± sqrt(-36)) / 2x = (-8 ± 6i) / 2x = -4 ± 3i
So the roots of [tex]x^2[/tex] + 8x + 25 are x = -4 + 3i and x = -4 - 3i.
So, the four roots of [tex]`f(x) = (x^2 + 4)(x^2 + 8x + 25) = 0[/tex]` are 2i, -2i, -4 + 3i, and -4 - 3i.
ii) The sum of these four roots is: 2i + (-2i) + (-4 + 3i) + (-4 - 3i) = -8.
Therefore, the sum of these four roots is -8.
To know more about roots visit:
https://brainly.com/question/12850021
#SPJ11
Given the differential equation, (x^2+y^2)+2xydy/dx=0 a) Determine whether the differential equation is separable or homogenous. Explain. b) Based on your response to part (a), solve the given differential equation with the appropriate method. Do not leave the answer in logarithmic equation form. c) Given the differential equation above and y(1)=2, solve the initial problem.
(A) This differential equation is not separable, but it is homogeneous since the degree of both terms in the brackets is the same and equal to [tex]$2.$[/tex] (B) The solution to the given differential equation is: [tex]$$\boxed{y^2 = \frac{Cx^2}{2} - \frac{x^2}{2} \ln(1 + \frac{y^2}{x^2})}$$[/tex] where [tex]$C$[/tex] is the constant of integration. (C) The solution to the initial value problem is: [tex]$$y^2 = \frac{(2\ln(5) + 8)x^2}{2} - \frac{x^2}{2} \ln(1 + \frac{y^2}{x^2})$$[/tex]
a) To determine whether the differential equation is separable or homogenous, let us check whether the equation can be written in the form of:
[tex]$$N(y) \frac{dy}{dx} + M(x) = 0$$[/tex] or in the form of:
[tex]$$\frac{dy}{dx} = f(\frac{y}{x})$$[/tex]
For the given equation:
[tex]$$(x^2 + y^2) + 2xy \frac{dy}{dx} = 0$$[/tex]
Upon dividing both sides by:
[tex]$x^2$,$$\frac{1}{x^2}(x^2 + y^2) + 2 \frac{y}{x} \frac{dy}{dx} = 0$$or$$1 + (\frac{y}{x})^2 + 2 \frac{y}{x} \frac{dy}{dx} = 0$$[/tex]
This equation is not separable, but it is homogeneous since the degree of both terms in the brackets is the same and equal to [tex]$2.$[/tex]
b) We can solve the given differential equation using the method of substitution.
First, let [tex]$y = vx.$[/tex]
Then, [tex]$\frac{dy}{dx} = v + x \frac{dv}{dx}.$[/tex]
Substituting these values into the equation, we get:
[tex]$$x^2 + (vx)^2 + 2x(vx) \frac{dv}{dx} = 0$$$$x^2(1 + v^2) + 2x^2v \frac{dv}{dx} = 0$$$$\frac{dv}{dx} = -\frac{1}{2v} - \frac{x}{2(1 + v^2)}$$[/tex]
Now, this differential equation is separable, and we can solve it using the method of separation of variables.
[tex]$$-2v dv = \frac{x}{1 + v^2} dx$$$$-\int 2v dv = \int \frac{x}{1 + v^2} dx$$$$-v^2 = \frac{1}{2} \ln(1 + v^2) + C$$$$v^2 = \frac{C - \ln(1 + v^2)}{2}$$$$y^2 = \frac{Cx^2}{2} - \frac{x^2}{2} \ln(1 + \frac{y^2}{x^2})$$[/tex]
Therefore, the solution to the given differential equation is:
[tex]$$\boxed{y^2 = \frac{Cx^2}{2} - \frac{x^2}{2} \ln(1 + \frac{y^2}{x^2})}$$[/tex]
where [tex]$C$[/tex] is the constant of integration.
c) Given the differential equation above and [tex]$y(1) = 2,$[/tex] we can substitute [tex]$x = 1$ and $y = 2$[/tex] in the solution equation obtained in part (b) to find the constant of integration [tex]$C[/tex].
[tex]$$$y^2 = \frac{Cx^2}{2} - \frac{x^2}{2} \ln(1 + \frac{y^2}{x^2})$$$$2^2 = \frac{C \cdot 1^2}{2} - \frac{1^2}{2} \ln(1 + \frac{2^2}{1^2})$$$$4 = \frac{C}{2} - \frac{1}{2} \ln(5)$$$$C = 2\ln(5) + 8$$[/tex]
Thus, the solution to the initial value problem is: [tex]$$y^2 = \frac{(2\ln(5) + 8)x^2}{2} - \frac{x^2}{2} \ln(1 + \frac{y^2}{x^2})$$[/tex]
To know more about differential equation visit:
https://brainly.com/question/32514740
#SPJ11
the data represents how much soil of a pound is in each bag. If the soil was redistributed into equal amounts, how much soil would be in each bag?
The calculated value of the amount of soil that would be in each bag is 1/2
How to determine how much soil would be in each bag?From the question, we have the following parameters that can be used in our computation:
The line plot
The amount of soil that would be in each bag is the mean/average
And this is calculated using
Mean = (1/8 * 2 + 1/4 * 1 + 1/2 * 3 + 3/4 * 4)/10
Evaluate
Mean = 1/2
Hence, the amount of soil that would be in each bag is 1/2
Read more about mean at
https://brainly.com/question/14532771
#SPJ1
A health expert evaluates the sleeping patterns of adults. Each week she randomly selects 65 adults and calculates their average sleep time. Over many weeks, she finds that 5% of average sleep time is less than 3 hours and 5% of average sleep time is more than 3.4 hours. What are the mean and standard deviation (in hours) of sleep time for the population? (Round "Mean" to 1 decimal places and "standard deviation" to 3 decimal places.) Mean ______________
Standard deviation _____________
Mean: 6.7 hours
Standard deviation: 0.35 hours
The mean sleep time for the population is 6.7 hours, and the standard deviation is 0.35 hours. To calculate these values, the health expert randomly selects 65 adults each week and calculates their average sleep time. Over many weeks, she finds that 5% of the average sleep time is less than 3 hours and 5% is more than 3.4 hours.
From this information, we can infer that the distribution of sleep times is approximately normal. Since the mean sleep time is 6.7 hours, it suggests that the distribution is centered around this value. The standard deviation of 0.35 hours indicates the variability or spread of the sleep times around the mean.
The fact that 5% of the average sleep time is less than 3 hours and 5% is more than 3.4 hours allows us to estimate the standard deviation. In a normal distribution, approximately 2.5% of the data falls below 1.96 standard deviations below the mean, and 2.5% falls above 1.96 standard deviations above the mean. Therefore, we can calculate the standard deviation as (3.4 - 6.7) / 1.96 ≈ 0.35.
In conclusion, the mean sleep time for the population is 6.7 hours, and the standard deviation is 0.35 hours. These values represent the average and variability of sleep times among the adults evaluated by the health expert.
Learn more about: standard deviation
brainly.com/question/29115611
#SPJ11
A marching band begins its performance
in a pyramid formation. The first row has 1 band member,
the second row has 3 band members, the third row has
5 band members, and so on. (Examples 1 and 2)
a. Find the number of band members in the 8th row.
Answer:
15 members in the 8th row
Step-by-step explanation:
To find the number of band members in the 8th row of the pyramid formation, we can observe that the number of band members in each row follows an arithmetic sequence where the common difference is 2.
To find the number of band members in the 8th row, we can use the formula for the nth term of an arithmetic sequence:
nth term = first term + (n - 1) * common difference
In this case, the first term is 1 (the number of band members in the first row), the common difference is 2, and we want to find the 8th term.
Plugging the values into the formula:
8th term = 1 + (8 - 1) * 2
Calculating:
8th term = 1 + 7 * 2
8th term = 1 + 14
8th term = 15
How much energy is needed to desalt 1kg of seawater
Desalination is a process that involves removing salt and other minerals from seawater, brackish water, or other water sources to make it suitable for human consumption.
It is achieved through various methods like thermal, membrane, and electrodialysis, and each requires a different amount of energy to operate. To determine the amount of energy required to desalinate seawater, one has to consider several factors like the type of desalination technology used, the efficiency of the process, the salinity of the water, and the quantity of water that needs desalination.Therefore, there is no specific answer to this question. The amount of energy required to desalinate seawater varies depending on the above factors. Nonetheless, the main factor is the type of desalination technology used. For instance, the reverse osmosis method requires approximately 3-4 kWh per cubic meter of water produced, while the multi-effect distillation method requires about 70-100 kWh per cubic meter of water produced.The above analysis shows that the amount of energy required to desalt 1kg of seawater varies depending on the desalination technology used. Therefore, the answer to this question cannot be accurately provided without specifying the type of technology.
In conclusion, to determine the amount of energy required to desalt seawater, one must consider several factors, including the desalination technology used, the efficiency of the process, the salinity of the water, and the quantity of water that needs desalination.
learn more about minerals visit:
brainly.com/question/29970865
#SPJ11
A 9.00 L balloon contains helium gas at a pressure of 625mmHg. What is the final pressure, in millimeters of mercury, of the helium gas at each of the following volumes if there is no change in temperature and amount of gas? 21.0 L Express your answer numerically in millimeters of mercury.
The final pressure of the helium gas at a volume of 21.0 L is 216 mmHg.
According to Boyle's Law, the pressure and volume of a gas are inversely proportional, provided the temperature and amount of gas remain constant. Mathematically, this relationship can be expressed as P₁V₁ = P₂V₂, where P₁ and V₁ are the initial pressure and volume, and P₂ and V₂ are the final pressure and volume.
In this case, the initial volume V₁ is 9.00 L and the initial pressure P₁ is 625 mmHg. The final volume V₂ is given as 21.0 L, and we need to find the final pressure P₂.
Using Boyle's Law, we can rearrange the equation as P₂ = (P₁V₁) / V₂. Substituting the given values, we have P₂ = (625 mmHg * 9.00 L) / 21.0 L.
Simplifying the expression, we find P₂ = 28125 mmHg * L / L. The units of liters cancel out, leaving us with P₂ = 28125 mmHg.
Therefore, the final pressure of the helium gas at a volume of 21.0 L is 28125 mmHg.
Learn more about final pressure
brainly.com/question/33354580
#SPJ11
Draw the group table for the factor group Z_4×Z_2/⟨ (2,1)⟩.
This is the group table for the factor group Z_4×Z_2/⟨ (2,1)⟩.
| (0,0) | (1,0) | (2,0) | (3,0) | (0,1) | (1,1) | (2,1) | (3,1)
------------------------------------------------------------------
(0,0) | (0,0) | (0,0) | (0,0) | (0,0) | (0,0) | (0,0) | (0,0) | (0,0)
------------------------------------------------------------------
(1,0) | (1,0) | (0,0) | (3,0) | (2,0) | (1,0) | (0,0) | (3,0) | (2,0)
------------------------------------------------------------------
(2,0) | (2,0) | (3,0) | (0,0) | (1,0) | (2,0) | (3,0) | (0,0) | (1,0)
------------------------------------------------------------------
(3,0) | (3,0) | (2,0) | (1,0) | (0,0) | (3,0) | (2,0) | (1,0) | (0,0)
------------------------------------------------------------------
(0,1) | (0,0) | (2,0) | (1,0) | (3,0) | (0,0) | (2,0) | (1,0) | (3,0)
------------------------------------------------------------------
(1,1) | (1,0) | (1,1) | (2,0) | (2,1) | (3,0) | (3,1) | (0,0) | (0,1)
------------------------------------------------------------------
(2,1) | (2,0) | (3,1) | (3,0) | (0,0) | (1,0) | (0,1) | (1,0) | (2,0)
------------------------------------------------------------------
(3,1) | (3,0) | (0,0) | (1,0) | (2,0) | (0,1) | (1,0) | (2,1) | (3,0)
------------------------------------------------------------------
To draw the group table for the factor group Z_4×Z_2/⟨ (2,1)⟩, we need to understand the concept of a factor group and the given group Z_4×Z_2.
The group Z_4×Z_2 is the direct product of two cyclic groups: Z_4 (integers modulo 4) and Z_2 (integers modulo 2). It contains elements of the form (a,b), where a is an integer modulo 4 and b is an integer modulo 2.
The factor group Z_4×Z_2/⟨ (2,1)⟩ is formed by taking the quotient group of Z_4×Z_2 with the subgroup generated by the element (2,1). This means that we will consider the cosets of ⟨ (2,1)⟩ and represent the elements of the factor group as these cosets.
To draw the group table, we list all the elements of the factor group and perform the group operation (which is usually multiplication) on them.
First, let's list the elements of Z_4×Z_2:
(0,0), (1,0), (2,0), (3,0), (0,1), (1,1), (2,1), (3,1)
Now, let's calculate the cosets of ⟨ (2,1)⟩. To do this, we multiply each element of Z_4×Z_2 by (2,1) and find the remainder when divided by (4,2). This will give us the cosets of ⟨ (2,1)⟩.
(0,0) + ⟨ (2,1)⟩ = (0,0)
(1,0) + ⟨ (2,1)⟩ = (1,0)
(2,0) + ⟨ (2,1)⟩ = (2,0)
(3,0) + ⟨ (2,1)⟩ = (3,0)
(0,1) + ⟨ (2,1)⟩ = (2,1)
(1,1) + ⟨ (2,1)⟩ = (3,1)
(2,1) + ⟨ (2,1)⟩ = (0,0)
(3,1) + ⟨ (2,1)⟩ = (1,0)
Now, we can fill in the group table by performing the group operation (multiplication) on the cosets of ⟨ (2,1)⟩.
Each element is represented by its coset, and the group operation is performed by multiplying the cosets together.
Learn more about cosets:
https://brainly.com/question/29585253
#SPJ11
How much work, w, must be done on a system to decrease its volume from 19.0 L to 11.0 L by exerting a constant pressure of 3.0 atm?
The work done on the system to decrease its volume from 19.0 L to 11.0 L, with a constant pressure of 3.0 atm, is 24.0 L·atm.
To calculate the work done on a system, we can use the formula:
w = -PΔV
where w is the work done, P is the constant pressure, and ΔV is the change in volume.
In this case, theconstant (V1) is 19.0 L and the final volume (V2) is 11.0 L. Therefore, the change in volume is:
ΔV = V2 - V1
= 11.0 L - 19.0 L
= -8.0 L
Since the volume has decreased, the change in volume is negative.
Substituting the given values into the work formula, we have:
w = -(3.0 atm) * (-8.0 L)
= 24.0 L·atm
Therefore, the work done on the system to decrease its volume from 19.0 L to 11.0 L, with a constant pressure of 3.0 atm, is 24.0 L·atm.
Learn more about constant
https://brainly.com/question/27983400
#SPJ11
Find the minimum and maximum values of the function on the given interval by comparing values at the critical points and endpoints. [12.3] (Give exact answers. Use symbolic notation and fractions where needed.) y = x³ - 24 In (x) + 7,
To find the minimum and maximum values of the function y = x³ - 24 In(x) + 7 on the interval [12.3], we need to examine the critical points and endpoints. The endpoints of the interval are x = 1 and x = 2. We evaluate the function at these points and compare the values to determine the minimum and maximum.
To find the critical points, we take the derivative of the function y = x³ - 24 In(x) + 7 with respect to x. The derivative is dy/dx = 3x² - 24/x. Setting this equal to zero and solving for x, we get 3x² - 24/x = 0. Multiplying through by x, we have 3x³ - 24 = 0. Solving this equation, we find that x = 2 is the only critical point.
Next, we evaluate the function at the critical point and the endpoints of the interval. When x = 1, y = 1³ - 24 In(1) + 7 = 1 - 24(0) + 7 = 8. When x = 2, y = 2³ - 24 In(2) + 7 = 8 - 24(0.693) + 7 ≈ -4.736. Comparing these values, we see that y = 8 is the maximum value on the interval, and y = -4.736 is the minimum value.
Therefore, the maximum value of the function y = x³ - 24 In(x) + 7 on the interval [12.3] is 8, and the minimum value is -4.736.
Learn more about function here : brainly.com/question/31062578
#SPJ11
To find the minimum and maximum values of the function y = x³ - 24 In(x) + 7 on the interval [12.3], we need to examine the critical points and endpoints.
The endpoints of the interval are x = 1 and x = 2. We evaluate the function at these points and compare the values to determine the minimum and maximum.
To find the critical points, we take the derivative of the function y = x³ - 24 In(x) + 7 with respect to x. The derivative is dy/dx = 3x² - 24/x.
Setting this equal to zero and solving for x, we get 3x² - 24/x = 0. Multiplying through by x, we have 3x³ - 24 = 0. Solving this equation, we find that x = 2 is the only critical point.
Next, we evaluate the function at the critical point and the endpoints of the interval. When x = 1, y = 1³ - 24 In(1) + 7 = 1 - 24(0) + 7 = 8. When x = 2, y = 2³ - 24 In(2) + 7 = 8 - 24(0.693) + 7 ≈ -4.736. Comparing these values, we see that y = 8 is the maximum value on the interval, and y = -4.736 is the minimum value.
Therefore, the maximum value of the function y = x³ - 24 In(x) + 7 on the interval [12.3] is 8, and the minimum value is -4.736.
Learn more about function here : brainly.com/question/31062578
#SPJ11
Calculate the rate at which NO₂ is being consumed in the following reaction at the moment in time when N₂O4 is formed at a rate of 0.0048 M/s. (BE SURE TO INCLUDE UNITS IN YOUR ANSWER) 2NO₂(g) → N₂O4(g)
The rate at which NO₂ is being consumed in the reaction at the moment in time when N₂O₄ is formed at a rate of 0.0048 M/s is 0.0024 M/s.
The rate at which NO₂ is being consumed can be determined using the stoichiometry of the reaction and the rate of formation of N₂O₄. In this reaction, 2 moles of NO₂ react to form 1 mole of N₂O₄.
To calculate the rate of consumption of NO₂, we can use the following relationship:
Rate of NO₂ consumption = (Rate of N₂O₄ formation) / (Stoichiometric coefficient of NO₂)
In this case, the rate of N₂O₄ formation is given as 0.0048 M/s. The stoichiometric coefficient of NO₂ is 2.
Therefore, the rate at which NO₂ is being consumed is:
Rate of NO₂ consumption = 0.0048 M/s / 2 = 0.0024 M/s
So, the rate at which NO₂ is being consumed is 0.0024 M/s.
Learn more about rate of consumption here: https://brainly.com/question/31324716
#SPJ11
Help what's the answer?
The slope is 2.5, and it means that the concentration increases by 2.5 PPM per year.
Which is the meaning of the slope of the line?Here we have the equation:
C = mt + b
Where c is the concentration, and t is the year.
So, m, the slope, tells us how much increases the concentration per year.
If a line passes through two points (x₁, y₁) and (x₂, y₂), then the slope is:
m = (y₂ - y₁)/(x₂ - x₁)
Here we have the two points (1960, 265) and (2020, 415)
So the slope is:
m = (415 - 265)/(2020 - 1960)
m = 2.5
So the concentration increases by 2.5 PPM per year.
Learn more about linear equations at:
https://brainly.com/question/1884491
#SPJ1
A reinforced concrete beam 20 mm x 200 mm with tensile reinforcement of 3-28 mm phi is simply supported over a span of 5.5m. Using steel covering of 75 mm, concrete strength is 20.7 MPa and yield steel strength of re-bars is 280 MPa. Determine the moment capacity of the beam and describe the mode of the design.
The moment capacity of the reinforced concrete beam is 26092.708kNm and the design mode if the calculated moment capacity is greater than or equal to the applied bending moment, the design is considered safe.
To determine the moment capacity of the reinforced concrete beam, we can follow the step-by-step calculation process:
Calculate the effective depth (d):
d = total depth - steel covering - bar diameter / 2
d = 200 mm - 75 mm - 28 mm / 2
d = 173 mm
Calculate the lever arm (a):
a = effective depth / 2
a = 173 mm / 2
a = 86.5 mm
Determine the neutral axis depth (x):
x = a / (0.87 *[tex]\sqrt{f_{ck}}[/tex])
x = 86.5 mm / (0.87 * [tex]\sqrt{20.7 }[/tex])
x = 205.7 mm
Calculate the balanced steel ratio ([tex]\rho_{bal}[/tex] ):
[tex]\rho_{bal}[/tex] = 0.87 * [tex]f_y / f_{ck}[/tex]
[tex]\rho_{bal}[/tex] = 0.87 * 280 MPa / 20.7 MPa
[tex]\rho_{bal}[/tex] = 11.76%
Determine the moment capacity ([tex]M_c[/tex]):
[tex]M_c[/tex] = 0.36 * [tex]f_{ck}[/tex] * b * x * (d - 0.4167 * x)
[tex]M_c[/tex] = 0.36 * 20.7 MPa * 200 mm * 205.7 mm * (173 mm - 0.4167 * 205.7 mm)
[tex]M_c[/tex] = 26092.708kNm
The mode of the design depends on the calculated moment capacity compared to the applied bending moment. If the calculated moment capacity is greater than or equal to the applied bending moment, the design is considered safe. Otherwise, additional measures such as increasing the depth, providing additional reinforcement, or using a higher strength concrete or steel may be required.
Learn more about reinforced concrete beam here:
https://brainly.com/question/33303426
#SPJ4
The solution for x² + 2x + 8 ≤0 is
The empty set
2 or 4
-2 or 4
The solution to the inequality x² + 2x + 8 ≤ 0 is the empty set, which means there are no values of x that satisfy the inequality.
To solve the inequality x² + 2x + 8 ≤ 0, we can use various methods such as factoring, completing the square, or the quadratic formula.
Let's solve it by factoring:
Start with the inequality: x² + 2x + 8 ≤ 0.
Attempt to factor the quadratic expression on the left-hand side. However, in this case, the quadratic does not factor nicely using integers.
Since factoring doesn't work, we can use the quadratic formula to find the roots of the quadratic equation x² + 2x + 8 = 0.
The quadratic formula is given by: x = (-b ± √(b² - 4ac)) / (2a), where a, b, and c are the coefficients of the quadratic equation (ax² + bx + c = 0).
Plugging in the values for our equation, we get: x = (-2 ± √(2² - 418)) / (2*1).
Simplifying further, we have: x = (-2 ± √(-28)) / 2.
Since the discriminant (-28) is negative, there are no real solutions, which means the quadratic equation has no real roots.
For similar question on inequality.
https://brainly.com/question/30238989
#SPJ8
Esercizio 3. Consider the linear map F: R^4-R^3 given by
F(x, y, z, w) = (x+y+z, x+y+w, 2x+2y). 1. Find the matrix associated with F.
2. What is the dimension of the kernel of F?
Finding the matrix associated with Fathey matrix A associated with the linear map F is given by:
[tex]A
c
where
e1 = (1, 0, 0, 0)
, e2
= (0, 1, 0, 0),
e3 = (0, 0, 1, 0),
e4 = (0, 0, 0, 1).
We have: F(e1)
= (1, 1, 2
)F(e2) = (1, 1, 2)
F(e3) = (1, 0, 2)
F(e4)
= (0, 1, 0)[/tex]
Thus, we have:
[tex]A = | 1 1 1 0 | | 1 1 0 1 | | 2 2 2 0 |. 2.[/tex]
Determining the dimension of the kernel of F: The kernel of F is the set of all vectors (x, y, z, w) in R4 such that.
F(x, y, z, w)
= (0, 0, 0).
In other words, the kernel of F is the solution set of the system of linear equations:
x + y + z = 0
x + y + w = 0 2x + 2y
= 0
This system has two free variables (say z and w). Hence, we can write the solution set in the parametric form as:
[tex]x
= -z-yw
= -yz,[/tex]
y, and w are free variables.
Thus, the kernel of F has dimension 2.
Answer:
The matrix associated with F is given by
[tex]| 1 1 1 0 | | 1 1 0 1 | | 2 2 2 0 |2.[/tex]
To know more about system visit:
https://brainly.com/question/19843453
#SPJ22
In the cementation process, the copper concentration in the pregnant leach liquor which enters the cementation launder contains 20gpl copper and can be reduced to very low levels in the cementation process. The barren liquor leaves the cementation launder at 25°C and contains 0.6gpl of iron, i) Write down the reaction depicting the cementation of copper by iron and calculate the overall cell potential 11) estimate the residual copper content of the barren liquor i.e. remaining copper in the solution after cementation 111) Hence estimate the % copper recovered from solution
1) The reaction depicting the cementation of copper by iron is:
Cu2+(aq) + Fe(s) -> Cu(s) + Fe2+(aq)
2) To calculate the overall cell potential, we need to use the standard reduction potentials of the half-reactions involved. The reduction potential of Cu2+ to Cu is +0.34V, and the reduction potential of Fe2+ to Fe is -0.44V. The overall cell potential can be calculated by subtracting the reduction potential of the anode reaction (Fe2+ to Fe) from the reduction potential of the cathode reaction (Cu2+ to Cu).
Overall cell potential = (+0.34V) - (-0.44V)
= +0.34V + 0.44V
= +0.78V
Therefore, the overall cell potential of the cementation process is +0.78V.
3) To estimate the residual copper content of the barren liquor, we need to calculate the amount of copper that has been removed during the cementation process. Since the initial copper concentration in the pregnant leach liquor is 20gpl and the barren liquor contains 0.6gpl of iron, we can assume that all the iron has reacted with copper to form copper metal. Therefore, the amount of copper removed can be calculated by multiplying the iron concentration by its molar mass (55.85g/mol) and dividing it by the molar mass of copper (63.55g/mol).
Amount of copper removed = (0.6gpl * 55.85g/mol) / 63.55g/mol
= 0.5274gpl
Therefore, the residual copper content in the barren liquor is approximately 20gpl - 0.5274gpl = 19.4726gpl.
4) To estimate the percentage of copper recovered from the solution, we can calculate the percentage of copper removed from the initial concentration of copper in the pregnant leach liquor.
% Copper recovered = (Amount of copper removed / Initial copper concentration) * 100
= (0.5274gpl / 20gpl) * 100
= 2.637%
Therefore, the percentage of copper recovered from the solution is approximately 2.637%.
To know more about cementation of copper :
https://brainly.com/question/32109091
#SPJ11
3. Solve the following system of equations: Vir - 2ary + s 14 - Tatry - Bar - 7+lling + 180g 12 17 Given that the coefficient matrix factors as T 1 001 HT 2 ID - 11 IN . :)
The solution to the given system of equations is:
Vir = 1, ary = 3, s = 5, Tatry = -2, Bar = 4, lling = 8.
To solve the system of equations, we can use the coefficient matrix factors T and H. The coefficient matrix can be written as:
T * H = [1 0 0; 0 1 0; -1 1 1; 0 -1 0; 0 0 1; 0 0 1].
We can break down the given system of equations into three parts using the columns of the coefficient matrix. Let's call the columns of T as T1, T2, and T3, and the corresponding variables as X1, X2, and X3. The three parts of the system can be written as follows:
T1 * X1 = [1 0 0] * [Vir; ary; s] = Vir
T2 * X2 = [0 1 0] * [Tatry; Bar; -7] = Bar - Tatry - 7
T3 * X3 = [0 0 1] * [lling; 180; g] = lling + 180g
By comparing the equations, we can determine the values of the variables:
From the first equation, we have Vir = 1.
From the second equation, we have Bar - Tatry - 7 = 4 - (-2) - 7 = 4 + 2 - 7 = -1.
From the third equation, we have lling + 180g = 8.
Therefore, the solution to the system of equations is:
Vir = 1, ary = 3, s = 5, Tatry = -2, Bar = 4, lling = 8.
Learn more about system of equations
brainly.com/question/21620502
#SPJ11