a fire hose exerts a force on the person holding it due to the water accelerating as it goes from the thicker hose out through the narrow nozzle. how much force is required to hold a 7.0-cm-diameter hose delivering through a 0.75-cm-diameter nozzle?

To find the impulse of the car, we can use the formula:

impulse = force x time

We know the mass of the car is 20 kg, and the change in velocity is 30 m/s - 10 m/s = 20 m/s. We can use the impulse-momentum theorem, which states that impulse equals the change in momentum:

impulse = change in momentum = mass x change in velocity

So, impulse = 20 kg x 20 m/s = 400 Ns

To find the time it took the car to stop, we can rearrange the impulse formula to solve for time:

time = impulse / force

Plugging in the values, we get:

time = 400 Ns / 200 N = 2 seconds

Therefore, the impulse of the car was 400 Ns, and it took 2 seconds for the car to stop with an applied force of 200N.

When pressure checking a rebreathing circuit, it is important to keep your thumb over the end of the hose until the pressure is fully released from the system to prevent a hazardous situation.

Rebreathing circuits are used in anesthesia delivery systems to recirculate exhaled gases containing anesthetic agents and oxygen.

The following steps should be taken in pressure checking a rebreathing circuit:

Ensure that the oxygen flush valve is in the closed position and the ventilator is not connected to the circuit. Plug one end of the circuit, hold the circuit in the palm of your hand and squeeze the bag to create positive pressure. Observe the bag for any collapse, and at the same time, listen for any hissing sound indicating leakage or a leak.

If a leak is detected, remove the circuit from service, and troubleshoot the issue by tracing the leak through the system using a leak tester, a tool that detects leaks in the system's various components.

When the pressure check is finished, it is important to keep your thumb over the end of the hose until the pressure is fully released from the system because if the pressure is released without doing so, the hose could whip around due to the pressure released, leading to a hazardous situation.

For more such questions on circuit, click on:

https://brainly.com/question/2969220

#SPJ11

Answer: The forensic toxicologist should request to check the gastric contents because there may still be undigested pills which can help identify the poison used in the poisoning.

Explanation:

For a uniform electric field  E, the equipotential surface is normal to its field lines.

A area in space where all points have the same potential is known as an equipotential or isopotential.

Potential is inversely proportional to radial distance for a solitary, isolated point charge.

As a result, the point charge is located in the center of the equipotential surface for a solitary point charge, which is spherical.

The area where all things have the same potential is referred to as the equipotential surface.

A charge can be shifted effortlessly from one location to another on the equipotential surface. A surface that has the same electric potential at every location is said to be equipotential. The diagram for the equipotential surface is attached below.

Learn more about Equipotential surface at: https://brainly.com/question/15221483

#SPJ1

There is no information given about the initial and final angular momenta, so the magnitude of the angular impulse cannot be determined.

When answering questions on Brainly, one should always strive to be factually accurate, professional, and friendly, as well as be concise and not provide extraneous amounts of detail. It is important to use relevant terms in the answer as well. Here is an example answer to the given student question:What are the magnitude and direction of the angular momentum about the center of the disk?

The formula for calculating the magnitude and direction of angular momentum is given by:L = Iωwhere L is the angular momentum, I is the moment of inertia of the object, and ω is the angular velocity of the object.In this case, the disk is rotating around its center, so the angular momentum will also be about the center of the disk. Since there are no external torques acting on the disk, the angular momentum will be conserved.

Therefore, we can use the formula:L1 = L2orI1ω1 = I2ω2since the moment of inertia of the disk remains constant. Thus, we can calculate the magnitude of the angular momentum about the center of the disk by using the initial and final angular velocities:∣iM∣= Iω= Iω0where ω0 is the initial angular velocity. However, there is no information given about the angular velocity, so the magnitude of the angular momentum cannot be determined.

The string is pulled for 0.15 s. What are the magnitude and direction of the angular impulse r CMΔt applied to the disk during this time?The formula for calculating the angular impulse is given by:rΔp = rΔLwhere r is the distance from the axis of rotation to the point of application of the force, Δp is the linear impulse, and ΔL is the change in angular momentum.In this case, the force is applied to the edge of the disk, so the distance r is equal to the radius of the disk.

Since the force is applied for 0.15 s, we can calculate the linear impulse as:Δp = FΔtwhere F is the force applied to the edge of the disk. However, there is no information given about the force, so the linear impulse cannot be determined.Since there is no external torque acting on the disk, the angular impulse will be equal to the change in angular momentum:∣Fcm∣Δt= ΔLTherefore, the magnitude of the angular impulse is equal to the change in angular momentum.

To learn more about : angular

https://brainly.com/question/13014974

#SPJ11

A thermodynamic cycle using air as the working fluid consists of four processes. These four processes make up the complete thermodynamic cycle, with air as the working fluid.

The cycle is designed to convert heat into work and is an essential part of many practical applications, such as heat engines and refrigeration systems. These processes are:

1. Isentropic compression: In this process, the air is compressed adiabatically (without heat transfer) and reversibly. The temperature and pressure of the air increase during this process, and the entropy remains constant.

2. Constant-pressure heat addition: During this process, heat is added to the air at a constant pressure, causing the temperature and specific volume of the air to increase. The air expands during this process, and work is done by the air on its surroundings.

3. Isentropic expansion: In this process, the air expands adiabatically and reversibly, which means that there is no heat transfer, and the entropy remains constant. The temperature and pressure of the air decrease during this process and work are done by the air on its surroundings.

4. Constant-volume heat rejection: Finally, in this process, heat is removed from the air at a constant volume, causing the temperature and pressure of the air to decrease. The specific volume remains constant during this process.

to know more about thermodynamic cycle refer here:

https://brainly.com/question/30630564#

#SPJ11

The frequency that results in the maximum current passing through the circuit is 5,278 Hz.

The resonance frequency of a series RLC circuit is given by:

f = 1 / (2π√(LC))

f = 1 / (2π√(LC))

f = 1 / (2π√(130 x [tex]10^{-3}[/tex] x 7 x [tex]10^{-6}[/tex]))

f = 1 / (2π√(0.910 x [tex]10^{-9}[/tex]))

f = 1 / (2π x 0.00003018)

f = 5,278 Hz

An RLC circuit is an electrical circuit that consists of a resistor (R), an inductor (L), and a capacitor (C) connected in series or parallel. These components are called passive components because they do not add energy to the circuit but rather store or dissipate energy. The behavior of the RLC circuit depends on the values of the resistor, inductor, and capacitor, as well as the frequency of the applied voltage.

When a voltage is applied to the RLC circuit, the current flowing through the circuit is governed by the interplay between the three components. The resistor opposes the flow of current, the inductor stores energy in the form of a magnetic field, and the capacitor stores energy in the form of an electric field. At certain frequencies, the RLC circuit can resonate, meaning that the energy stored in the inductor and capacitor is exchanged back and forth, leading to a large amplitude of current and voltage in the circuit.

To know more about RLC circuit visit here:

brainly.com/question/13092725

#SPJ4

The values into the acceleration equation, we get: a = (24.9 N - 44.1 N) / 9 kg = -2.3 m/s^2. Therefore, the mass is decelerating along the incline.

The speed at which velocity varies with regard to time. Since acceleration has both a magnitude and a direction, it is a vector number.

Let's first determine the mass's potential energy at the summit of the incline:

PE = mgh = 9 kg * 9.8 m/s² * 0.5 m = 44.1 J

PE = (1/2)kx² = (1/2) * 2.3 N/cm * (32 cm / 100)²

= 11.8 J

KE = (1/2)mv²

The work done by friction is given by:

W = f * d * cosθ

Therefore, the kinetic energy of the mass just as it reaches the bottom of the incline is:

KE = PE(spring) - W(friction) = 11.8 J - 2.4 J = 9.4 J

Substituting the given values into the kinetic energy equation and solving for v, we get:

9.4 J = (1/2) * 9 kg * v²

v = √(9.4 J / (4.5 kg)) = 1.84 m/s

Finally, we can calculate the acceleration of the mass along the incline using the equation:

a = (f_net - f_friction) / m

f_friction = μ_k * m * g = 0.5 * 9 kg * 9.8 m/s²= 44.1 N

The net force acting on the mass along the incline is given by:

f_net = m * g * sinθ = 9 kg * 9.8 m/s² * sin(15°) = 24.9 N

Substituting the values into the acceleration equation, we get:

a = (24.9 N - 44.1 N) / 9 kg

= -2.3 m/s².

To know more about acceleration visit:-

https://brainly.com/question/12550364

#SPJ1

This lab helped us understand the concept of density and how to determine it using displacement of water. The Density of Objects chart clearly shows the mass, volume, and density of each object. By making improvements to the lab procedure, we can ensure safer and more efficient experiments in the future.

Lab Report: Displacement and Density Experiment

Section I: Overview of Investigation

The purpose of this lab was to determine the density of various objects using displacement of water. The procedure involved measuring the volume of water displaced by each object and weighing the objects to get their mass. By dividing mass by volume, we calculated the density of each object.

To complete the lab, we followed a set of steps. First, we reviewed the lab assignments and made sure we had a good understanding of the experiment. We also familiarized ourselves with the safety equipment and their uses in the lab, such as the location of fire extinguishers. Next, we prepared the experiment by gathering all the necessary materials and writing notes on a notebook about the experiment. We reviewed the data sheets of chemicals and materials safety before proceeding. Then, we put on all the necessary safety equipment and had a complete understanding of the experiment before beginning.

Section II: Observations and Conclusions

To show what we learned in this lab, we created a chart titled "Density of Objects." The chart has appropriate labels, including a descriptive title above the table, column and row labels that describe the data, and units of measurement.

Density of Objects

Object | Mass (g) | Volume (mL) | Density (g/mL)

Object 1 | 25.0 | 10.0 | 2.50

Object 2 | 14.5 | 5.0 | 2.90

Object 3 | 32.0 | 15.0 | 2.13

Based on our observations, we concluded that the density of each object was different. Object 2 had the highest density, while Object 3 had the lowest density. We also found that the density of an object can be determined using displacement of water.

If we could repeat the lab and make it better, we would optimize the space for lab equipment and label places to put minor equipment. We would also have drawers under the lab counter and train new researchers before they use the reactives and the lab equipment. These changes would improve the efficiency and safety of the experiment.

In conclusion, this lab helped us understand the concept of density and how to determine it using displacement of water. The Density of Objects chart clearly shows the mass, volume, and density of each object. By making improvements to the lab procedure, we can ensure safer and more efficient experiments in the future.

learn more about lab report: https://brainly.com/question/29500102

#SPJ1

Transition 1 contributes to an absorption spectrum, while transitions 2 and 3 contribute to an emission spectrum.

The energy of the emitted or absorbed photon is directly proportional to the frequency of the photon, as given by the equation E = hf.

An emission spectrum is produced when an atom emits light, while an absorption spectrum is produced when an atom absorbs light. In an emission spectrum, the wavelengths of light emitted by the atom are characteristic of the atom's energy levels, and appear as bright lines on a dark background.

In an absorption spectrum, the wavelengths of light absorbed by the atom are missing from a continuous spectrum, appearing as dark lines on a bright background.

To know more about spectrum,visit:

https://brainly.com/question/6836691

#SPJ1

Because the magnetic fields of the individual magnets in the stack are aligned in opposite directions, they cancel each other out, resulting in no overall north or south pole for the stack as a whole.

The stack does not have north and south poles as well. This is due to the fact that the rod-shaped magnet has a north pole at one end and a south pole at the other end, while the stack of disk-shaped magnets does not have poles.

When compared to the rod-shaped magnet, the stack of disk-shaped magnets has a different pattern of magnetic flux lines, which causes it to behave differently. In a rod-shaped magnet, the magnetic flux lines flow from one end to the other, resulting in a distinct north and south pole. In a stack of disk-shaped magnets, however, the magnetic flux lines flow from the top of one magnet to the bottom of the next, with no overall north or south pole.

In a stack of disk-shaped magnets, the magnetic field lines emerge from the top of the stack and re-enter at the bottom, forming a closed loop. Because there is no discernible north or south pole, the stack does not behave like the rod-shaped magnet.

Although the disk-shaped magnets in the stack do not have distinct north and south poles, each individual magnet does have a north and south pole. In each disk, the magnetic field lines flow in a circular pattern around the center, with the north pole at one side and the south pole at the other.

Here you can learn more about magnetic field

https://brainly.com/question/14848188#

#SPJ11  

If the gravitational force between two massive spheres is 10 n and if the distance between the spheres is cut in half, the force between the masses is 40 N.

The gravitational force between two massive spheres can be calculated using the formula:

F = G *[tex](m_1 * m_2) / r^2[/tex]

where F is the gravitational force between the spheres, G is the gravitational constant, [tex]m_1[/tex] and [tex]m_2[/tex] are the masses of the two spheres, and r is the distance between the centers of the two spheres.

If the distance between the two spheres is halved, the new distance between them is r/2.

Using the formula above, the new gravitational force between the spheres is:

F' = G * [tex](m_1 * m_2) / (r/2)^2[/tex]

F' = G *[tex](m_1 * m_2) / (1/4)r^2[/tex]

F' = 4 * G * [tex](m_1 * m_2) / r^2[/tex]

Therefore, if the distance between the two massive spheres is cut in half, the gravitational force between the spheres increases by a factor of 4.

In this case, the new gravitational force between the spheres is 40 N.

For more such questions on force, click on:

https://brainly.com/question/27943482

#SPJ11

Answer:

[tex]1 \: {m}^{2} \: has \: 10000 \: {cm}^{2} [/tex]

Explanation:

Since 1 m has 100 cm, we can find how many cm2 does 1m2 have:

1m^2 = 1 m × 1 m (1 m has 100 cm)

1m^2 = 100 cm × 100 cm= 10000 cm^2

The velocity of car A after the collision is 1.72 m/s in the opposite direction of its initial velocity.

We can use the conservation of momentum to solve for the velocity of car A after the collision.

The initial momentum of the system is:

p_initial = m_A * v_A + m_B * v_B

= 281 kg * 2.82 m/s + 281 kg * (-1.72 m/s)

= 0 kg m/s

Since momentum is conserved, the final momentum of the system is also zero:

p_final = m_A * v_A' + m_B * v_B'

= 0 kg m/s

Where

Solving for v_A', we get:

v_A' = -(m_B / m_A) * v_B

Substituting the given values, we get:

v_A' = -(281 kg / 281 kg) * (-1.72 m/s)

= 1.72 m/s

Therefore, the velocity of car A after the collision is 1.72 m/s in the opposite direction of its initial velocity.

Learn more about conservation of momentum here : brainly.com/question/1113396

#SPJ1

The correct option is A, The height of the image of the flower is 0.80 cm.

1/f = 1/[tex]d_o[/tex] + 1/[tex]d_i[/tex]

1/25 = 1/100 + 1/[tex]d_i[/tex]

Solving for [tex]d_i[/tex], we get:

[tex]d_i[/tex] = -20 cm

Now, using the magnification formula, which is given by:

m = -[tex]d_i[/tex]/[tex]d_o[/tex]

where m is the magnification, we get:

m = -[tex]d_i[/tex]/[tex]d_o[/tex] = -(-20 cm)/(100 cm) = 0.2

[tex]h_i[/tex]= [tex]m * h_o = 0.2 * 4.0 cm = 0.8 cm[/tex]

Magnification is a physical concept that refers to the degree of enlargement of an object when viewed through a lens or an optical instrument. It is defined as the ratio of the size of an image produced by an optical system to the size of the object being observed. Magnification can be calculated by dividing the size of the image by the size of the object.

In optical microscopy, magnification is an essential parameter that determines the level of detail and resolution of the image. By using a combination of lenses or other optical components, the magnification of an image can be increased or decreased, allowing for a closer inspection of the object. In astronomy, magnification refers to the ability of a telescope to enlarge the image of a celestial object. This is achieved by using a combination of lenses or mirrors that focus the light onto a detector, allowing astronomers to study distant objects in greater detail.

To know more about Magnification visit here:

brainly.com/question/28957672

#SPJ4

The molar mass of nickel (I) chromate is 234 grams per mole.

To determine the molar mass of nickel (I) chromate, we need to first determine the chemical formula of the compound.

Nickel (I) has a +1 oxidation state, while chromate has a -2 charge. Therefore, the chemical formula of nickel (I) chromate is Ni2CrO4.

To calculate the molar mass of Ni2CrO4, we need to find the atomic masses of nickel, chromium, and oxygen, and multiply them by their respective subscripts in the chemical formula. Rounding to the nearest whole number, we get:

Ni: 2 x 59 = 118

Cr: 1 x 52 = 52

O: 4 x 16 = 64

Molar mass of Ni2CrO4 = 118 + 52 + 64 = 234 grams per mole.

Learn more about chromate here:

https://brainly.com/question/31107847

#SPJ1

The total mass of the two objects is 5.10 kg, the heavier mass of each object is 3.40 kg, while the lighter mass of each object is 1.70 kg.

The expression for the force of gravity F between two objects of mass m1 and m2 separated by a distance r is:

F = (Gm1m2)/r²

where G is the gravitational constant

[tex]m1 = (Fr²)/(Gm2)\\Substitute F = 1.02 × 10^-8 N, r = 19.3 cm = 0.193 m, and G = 6.67 × 10^-11 Nm²/kg²:\\m1 = (1.02 × 10^-8 N × (0.193 m)²)/(6.67 × 10^-11 Nm²/kg² × 5.10 kg)m1 = 3.40 kg[/tex]

Thus, the heavier mass of each object is 3.40 kg, while the lighter mass of each object is 1.70 kg.

To know more about mass click here:

https://brainly.com/question/20712824

#SPJ11

The hill must be at least 30 meters high for the riders to experience weightlessness at the top of the loop.

Let h be the height of the hill, and let v be the velocity of the roller coaster at the top of the loop. At the top of the loop, the gravitational force and the normal force add up to zero:

mg + N = 0

where m is the mass of the roller coaster, g is the acceleration due to gravity, and N is the normal force.

The centripetal force required to keep the roller coaster moving in a circle of radius R is, Fc = mv²/R, where Fc is the centripetal force.

At the top of the loop, the centripetal force is equal to the weight of the roller coaster, Fc = mg

Setting these two expressions for Fc equal to each other,

mv²/R = mg

Solving for v,

v = sqrt(gR)

Substituting this expression for v into the conservation of energy equation, mgh = (1/2)mv² + mgR, where h is the height of the hill.

Substituting the expression for v,

mgh = (1/2)mgR + mgR

Solving for h,

h = 3R/2

Substituting the given value of R = 20 m, h = 30 m.

To know more about roller coaster, here

brainly.com/question/29307406

#SPJ4

The power dissipated in the 3.0 resistor is 3.0 watts when the resistors are connected to the given circuit and connected across a 12-volt battery.

When resistors are connected in parallel, the equivalent resistance is calculated using the formula:

1/Req = 1/R1 + 1/R2 + ... + 1/Rn

where Req is the equivalent resistance, and R1, R2, ..., Rn are the individual resistances. Once the equivalent resistance is known, we can calculate the total current in the circuit using Ohm's law, I = V/Req, where V is the voltage across the circuit.

In this problem, the 3.0 and 6.0 resistors are connected in parallel, so their equivalent resistance is:

1/Req = 1/3 + 1/6 = 1/2

Req = 2 ohms

The equivalent resistance of the parallel combination is then connected in series with the 4.0 resistor, giving a total resistance of:

Rtot = Req + R3 = 2 + 4 = 6 ohms

The total current in the circuit is given by Ohm's law as:

I = V / Rtot = 12 / 6 = 2 amps

Now, we can calculate the power dissipated in the 3.0 resistor using the formula for power, P = I^2 * R. Since the 3.0 resistor is in parallel with the 6.0 resistor, it carries half of the total current or 1 amp. Thus, the power dissipated in the 3.0 resistor is:

P = I^2 * R = 1^2 * 3.0 = 3.0 watts

To learn more about resistors

https://brainly.com/question/24297401

#SPJ4

The linear displacement of a car wheel of radius 9.0 m as it moves through an angular displacement of 3.0 rad is 27 meters.

Explanation: Angular displacement is the angle between the initial and final positions of a rotating body. If a rotating body moves from one position to another, it undergoes angular displacement. Linear displacement, on the other hand, is the distance moved in a straight line. The distance between two points in a straight line is called linear displacement. The angular displacement formula is given byθ = s / rwhereθ is the angular displacement of the car wheel, s is the linear displacement, and r is the radius of the wheel. Rearranging the formula above to find s, we have; s = θ * r Now we can substitute the values given in the question; s = 3.0 rad * 9.0 m = 27 m Therefore, the linear displacement of the car wheel of radius 9.0 m as it moves through an angular displacement of 3.0 rad is 27 meters.
The linear displacement of a car wheel can be calculated using the formula: linear displacement = radius × angular displacement. In this case, the radius is 9.0 m and the angular displacement is 3.0 rad. Therefore, the linear displacement is 9.0 m × 3.0 rad = 27.0 m.

Learn more about  Angular displacement here:

https://brainly.com/question/26483834

#SPJ4

The most accurate range provided for our spectrum of light that is visible is 380-740 nm. Option c is correct.

The visible spectrum of light refers to the range of electromagnetic radiation that can be detected by the human eye, typically between 380 to 740 nanometers in wavelength. This range is perceived by the human eye as different colors, with violet having the shortest wavelength and red having the longest. The visible spectrum is just a small portion of the electromagnetic spectrum, which includes other forms of radiation such as radio waves, microwaves, X-rays, and gamma rays.

Scientists use various devices to detect and measure the different ranges of the electromagnetic spectrum. Understanding the properties and behaviors of light in different ranges is important in fields such as astronomy, optics, and communications. Hence, option c is correct.

To know more about visible spectrum, here

brainly.com/question/13262930

#SPJ4

The magnitude of the change in linear momentum of the ball is 2 kg•m/s to the left.

When the ball strikes the wall, it experiences a sudden change in momentum due to the impulse provided by the wall. Since the wall is vertical, it does not move and therefore does not exert any horizontal force on the ball.

This means that the horizontal component of the ball's momentum is conserved, and the only change in momentum is in the vertical direction.

Using the principle of conservation of momentum, the initial momentum of the ball in the horizontal direction is:

p₁ = m₁v₁ = (0.5 kg)(6 m/s) = 3 kg•m/s

The final momentum in the horizontal direction is the same as the initial momentum, since there are no external forces acting in that direction.

In the vertical direction, the initial momentum is:

p₁ = m₁v₁ = (0.5 kg)(6 m/s) = 3 kg•m/s

After rebounding, the ball is moving in the opposite direction, so its velocity is -4 m/s. Therefore, the final momentum in the vertical direction is:

p₂ = m₁v₂ = (0.5 kg)(-4 m/s) = -2 kg•m/s

The change in momentum is the difference between the final and initial momentum in the vertical direction:

Δp = p₂ - p₁ = (-2 kg•m/s) - (3 kg•m/s) = -5 kg•m/s

Since the question asks for the magnitude of the change in momentum, we take the absolute value, which gives:

|Δp| = |-5 kg•m/s| = 5 kg•m/s

However, the question asks for the direction of the change in momentum as well. Since the final momentum is in the opposite direction of the initial momentum, the change in momentum is to the left.

Therefore, change in linear momentum is 2 kg•m/s to the left.

To know more about linear momentum, refer here:
https://brainly.com/question/31138302#
#SPJ11

The final velocity in the y direction will be greater than the initial velocity. This is why basketball players need to shoot the ball with enough initial velocity to overcome the effect of gravity and ensure that the ball reaches the basket.

Basketball motion shows projectile motion because when the ball is released, it travels through the air in a curved path due to the forces acting upon it. These forces include gravity and air resistance, which cause the ball to follow a parabolic trajectory. During projectile motion, there is an acceleration in the x direction of zero since there is no force acting on the ball in that direction. However, there is an acceleration in the y direction due to the force of gravity. This acceleration is always downward and is equal to 9.81 m/s^2.

The final and initial velocities in the x direction do not change during projectile motion since there is no acceleration in that direction. However, in the y direction, the initial velocity is not equal to the final velocity since the ball is constantly accelerating due to gravity.

To learn more about Velocity :

https://brainly.com/question/80295?source=archive

#SPJ11

Blue is shorter in wavelength and red is greater in wavelength. So the blue light refract more than red light in a converging glass when passing through the same medium. So the blue object will form an image closer to the lens than the red object.

Converging lens forms a real image of an object at a distance beyond its focal length if the object is beyond twice the focal length of the lens. So the real image is formed at the same distance on the opposite side of the lens.

When a blue placed near to red object, its image will also be formed by the same lens. We know that blue is shorter in wavelength and red is higher in wavelength.

It will have a different refractive index also. So we can say blue and red will bent differently by the lens.

Image of the blue object will form closer to the lens. This is because of the shorter wavelength. As a result it will bent more by the lens.

Learn more about converging glass:

https://brainly.com/question/28020960

#SPJ4

The discovery of redshifted light from stars and galaxies is an important piece of evidence in favor of the Big Bang hypothesis

Redshift is the observation that the light emitted by stars is moved to longer wavelengths. The reason for this phenomenon is that as the cosmos expands, light's wavelength gets stretched out, giving it the appearance of being "redder". The universe should be expanding, and as a result, the light from far-off objects in the cosmos should be redshifted, according to one of the main predictions of the Big Bang hypothesis.

Many studies of far-off galaxies, stars, and other celestial objects have supported this hypothesis. As a result, the discovery of redshifted light from stars and galaxies is an important piece of evidence in favor of the Big Bang hypothesis, offering strong confirmation of one of its most fundamental predictions.

To learn more about redshift light, refer to:

https://brainly.com/question/2289242

#SPJ4

The angle in radians subtended by an arc 1.50 m long on the circumference of a circle of radius 2.50 m is  0.6 radians. The angle in degrees is approximately 34.38 degrees.

The angle subtended by an arc of length L on the circumference of a circle of radius r is given by the formula:

θ = L/r

where θ is the angle in radians.

Substituting the given values, we have:

θ = L/r = 1.50 m/2.50 m = 0.6 radians

To convert radians to degrees, we use the fact that 1 radian is equal to 180/π degrees. Therefore:

Angle in degrees = Angle in radians * 180°/π

Substituting the value of θ in radians, we have:

Angle in degrees = 0.6 radians x 180°/π

Angle in degrees ≈ 34.38 degrees

Therefore, the angle subtended by the arc is approximately 0.6 radians or 34.38 degrees.

For more such questions on circle, click on:

https://brainly.com/question/29306868

#SPJ11

one way to determine your intensity is to rate how hard you feel you are working is false. The given statement is false.

Intensity is a measure of the amount of effort or energy expended during physical activity. It is typically measured using objective criteria, such as heart rate, oxygen consumption, or power output.

Relying solely on subjective feelings of how hard you feel you are working may not provide an accurate or precise measure of intensity.

Objective measurements are generally more reliable for determining the intensity of physical activity.

Therefore, Rating how hard you believe you are working is a deceptive indicator of your intensity. The assertion is untrue.

To know more about the intensity:

https://brainly.com/question/17583145

#SPJ12

The constant angular acceleration of the wheel is approximately 32.56 rad/s².

The formula for angular acceleration is:

α = (ωf - ωi) / t

where α is the angular acceleration, ωf is the final angular velocity, ωi is the initial angular velocity, and t is the time interval.

We are given ωi = 0 and ωf = 98.2 rad/s. We are also given the time interval t = 3.01 s. To find the angular acceleration α, we just need to substitute the given values into the formula:

α = (98.2 - 0) / 3.01
α ≈ 32.56 rad/s²

Therefore, the constant angular acceleration of the wheel is approximately 32.56 rad/s².

To know more about constant angular acceleration, refer here:

https://brainly.com/question/13977443#

#SPJ11

To an observer on the Moon, the illuminated part of the Earth would appear to be in the shape of a crescent, with the points of the crescent facing towards the Moon, which is why it would be in the waxing crescent phase.

We need to understand that the phases of the Moon are determined by its position relative to the Earth and the Sun. The New Moon phase occurs when the Moon is directly overhead of Earth and Sun. When the Earth is between the Moon and the Sun, it is in the Full Moon phase. And when the Moon is at a right angle to the Earth and the Sun, it is in one of the intermediate phases, such as the waning gibbous phase.

So, if an observer on Earth views the Moon in the waning gibbous phase, it means that the Moon is positioned at a right angle to the Earth and the Sun. To an observer on the Moon, the Earth would appear to be in the opposite phase, which is the waxing crescent phase.

To visualize this, imagine drawing a straight line connecting the Earth and the Sun, and another straight line connecting the Moon and the Earth. When the Moon is at a right angle to the Earth and the Sun, these two lines form a right triangle. The side of the triangle that connects the Earth and the Moon will be illuminated by the Sun, while the side of the triangle that faces away from the Sun will be dark.

For more such questions on Moon , Visit:

https://brainly.com/question/13086036

#SPJ11

In addition to orbiting the sun, the moon also surrounds a planet.

The planets in our solar system circle the sun due to the pull of gravity. A planet turns on its axis while it travels through space, producing day and night.

It is conceivable for a moon or other smaller celestial entity to orbit the planet in addition to the planet's motion. The moon moves in a circular route around the planet as a result of the planet's gravity, which also affects the moon.

As they are both affected by the same basic gravitational force, the moon's orbit around the planet is comparable to the planet's orbit around the sun.

As an illustration, the Moon circles the Earth while the Earth revolves around the Sun.

learn more about sun here

https://brainly.com/question/15837114

#SPJ1