A 2 m³ oxygen tent initially contains air at 20°C and 1 atm (volume fraction of O₂ 0.21 and the rest N₂). At a time, t = 0 an enriched air mixture containing 0.35 O₂ (in volume fraction) and the balance N₂ is fed to the tent at the same temperature and nearly the same pressure at a rate of 1 m³/min, and gas is withdrawn from the tent at 20°C and 1 atm at a molar flow rate equal to that of the feed gas. (a) Write a differential equation for oxygen concentration x(t) in the tent, assuming that the tent contents are perfectly mixed (so that the temperature, pressure, and composition of the contents are the same as those properties of the exit stream). [5 marks] (b) Integrate the equation to obtain an expression for x(t). How long will it take for the mole fraction of oxygen in the tent to reach 0.33?

It is important to note that the selection of specific technologies should consider site-specific factors, regulatory requirements, and the characteristics of the gas emissions.

For the emissions described, I suggest the following technologies considering cost, ease of operation, and ultimate disposal of residuals:

a) Gas containing 70% SO2 and 30% N2:

To address the emission of gas containing 70% SO2 and 30% N2, the most suitable technology would be flue gas desulfurization (FGD). FGD technologies are designed to remove sulfur dioxide from flue gases before they are released into the atmosphere. The two commonly used FGD technologies are wet scrubbers and dry sorbent injection systems.

Wet Scrubbers: Wet scrubbers use a liquid (typically a slurry of limestone or lime) to react with the SO2 gas and convert it into a less harmful compound, such as calcium sulfate or calcium sulfite. Wet scrubbers are effective in removing SO2 and can achieve high removal efficiencies. They are relatively easy to operate and can handle high gas volumes. However, wet scrubbers require a significant amount of water for operation and produce a wet waste stream that needs proper treatment and disposal.

Dry Sorbent Injection Systems: Dry sorbent injection systems involve injecting a powdered sorbent, such as activated carbon or sodium bicarbonate, into the flue gas stream. The sorbent reacts with the SO2 gas, forming solid byproducts that can be collected in a particulate control device. Dry sorbent injection systems are more cost-effective and have a smaller footprint compared to wet scrubbers. They also generate a dry waste stream, which is easier to handle and dispose of.

b) Gas containing volatile organic compounds (VOCs):

To address emissions of gas containing volatile organic compounds (VOCs), a suitable technology would be catalytic oxidation. Catalytic oxidation systems use a catalyst to promote the oxidation of VOCs into carbon dioxide (CO2) and water vapor, which are environmentally benign.

Catalytic oxidation offers several advantages for VOC removal:

Cost-effectiveness: Catalytic oxidation systems are generally cost-effective in terms of operation and maintenance. Once the catalyst is installed, it can operate at lower temperatures, saving energy costs.

Ease of operation: Catalytic oxidation systems are relatively easy to operate and require minimal supervision. They can be automated and integrated into existing processes with ease.

Ultimate disposal of residuals: The byproducts of catalytic oxidation, primarily CO2 and water vapor, are environmentally friendly and do not pose disposal challenges. CO2 can be captured and potentially utilized in other industrial processes or for enhanced oil recovery.

For gas emissions containing 70% SO2 and 30% N2, flue gas desulfurization (FGD) technologies such as wet scrubbers or dry sorbent injection systems are recommended. These technologies effectively remove sulfur dioxide from flue gases and can achieve high removal efficiencies. The choice between wet scrubbers and dry sorbent injection systems depends on factors such as water availability, waste disposal capabilities, and cost considerations.

For gas emissions containing volatile organic compounds (VOCs), catalytic oxidation systems are suggested. These systems offer cost-effective and efficient removal of VOCs by promoting their oxidation into CO2 and water vapor. Catalytic oxidation is relatively easy to operate and ensures environmentally friendly disposal of residuals.

Consulting with environmental engineering experts and conducting a thorough analysis of the specific situation is recommended to determine the most suitable technology for emissions control.

To  know more about emissions , visit;

https://brainly.com/question/13537021

#SPJ11

a. The missing reactant for the transformation from benzene to ethylbenzene is ethene (C2H4). b. The missing reactant for the transformation to produce 2-bromo-5-sulfobenzoic acid is 2-bromobenzoic acid.

a. The transformation from benzene to ethylbenzene involves the addition of an ethyl group (C2H5) to the benzene ring. Ethene (C2H4) is a commonly used reactant in this process, and it reacts with a catalyst such as aluminum chloride (AlCl3) to produce ethylbenzene.

b. To synthesize 2-bromo-5-sulfobenzoic acid, the starting material is 2-bromobenzoic acid. The addition of a sulfonic acid group (-SO3H) to the 5th position of the benzene ring is carried out through a sulfonation reaction using sulfuric acid (H2SO4).

The missing reactants for the given transformations have been identified. The transformation from benzene to ethylbenzene requires ethene as a reactant, while the synthesis of 2-bromo-5-sulfobenzoic acid involves starting with 2-bromobenzoic acid. These reactants are crucial for the respective chemical reactions to occur and yield the desired products.

To know more about C2H4 , visit;

https://brainly.com/question/32913572

#SPJ11

In the given process, air is mixed with pure methanol, recycled, and fed to a reactor for the partial oxidation of methanol to produce formaldehyde (HCHO). However, some side reactions also occur, generating formic acid (HCOOH).

The partial oxidation of methanol (CH3OH) to formaldehyde (HCHO) can be represented by the following reaction:

2CH3OH + O2 → 2HCHO + 2H2O

However, in practice, side reactions can also occur, leading to the formation of formic acid (HCOOH). The overall reaction can be written as:

2CH3OH + O2 → 2HCHO + HCOOH + H2O

To optimize the process and control the selectivity towards formaldehyde, factors such as temperature, pressure, catalyst, and residence time need to be carefully controlled.

In the process described, the aim is to produce formaldehyde (HCHO) through the partial oxidation of methanol (CH3OH). However, side reactions can also generate formic acid (HCOOH). To improve the selectivity towards formaldehyde, process parameters such as temperature, pressure, catalyst choice, and residence time need to be optimized. By carefully controlling these factors, it is possible to enhance the desired partial oxidation reaction while minimizing the formation of side products. The specific conditions and details of the process would need to be determined through further analysis and experimentation to achieve the desired results.

To know more about methanol, visit

https://brainly.com/question/14889608

#SPJ11

Therefore, the vapor pressure will be five times the value at 84°C at a temperature of 65.5°C.

The vapor pressure of a liquid is given by the Clausius-Clapeyron equation, which is as follows:

ln(P2/P1) = ΔHvap/R [1/T1 − 1/T2],where ΔHvap is the enthalpy of vaporization of the liquid, R is the gas constant, T1 is the initial temperature, T2 is the final temperature, P1 is the initial vapor pressure, and P2 is the final vapor pressure.

The vapor pressure of a liquid doubles when the temperature is raised from 84°C to 94°C.

Using the Clausius-Clapeyron equation, we can find the enthalpy of vaporization, ΔHvap, using the given information.

Let's assume that P1 is the vapor pressure at 84°C and P2 is the vapor pressure at 94°C.P1/P2 = 0.5, which can be rewritten as P2 = 2P1.

Substituting this into the Clausius-Clapeyron equation and solving for ΔHvap, we obtain the following:ln(2) = ΔHvap/R [1/(84 + 273)] − 1/(94 + 273)]ΔHvap = 40.657 kJ/mol.

Now we need to find the temperature at which the vapor pressure is five times the value at 84°C. Let's call this temperature T3.

P1/P3 = 1/5, which can be rewritten as P3 = 5P1.

Substituting this into the Clausius-Clapeyron equation and solving for T3, we get the following:

ln(5) = (ΔHvap/R) [1/(84 + 273) − 1/T3]T3 = 338.5 K or 65.5°C.

To know more about Clausius-Clapeyron equation visit;

https://brainly.com/question/33369944

#SPJ11

The dew point temperature of the mixture is -41.12°C. The dew point temperature represents the temperature at which the water vapor in a gas mixture starts to condense into liquid water.

To calculate the dew point temperature, we need to consider the partial pressure of water vapor in the mixture. Given the total pressure of the mixture is 0.94 atm, we can calculate the partial pressure of water vapor using its mole fraction (9.63%) and the total pressure. The partial pressure of water vapor is found to be 0.0904 atm.

Using the partial pressure of water vapor, we can determine the dew point temperature using a dew point calculator or a dew point chart. Considering the partial pressure of water vapor (0.0904 atm), we find that the dew point temperature of the gas mixture is -41.12°C. At or below this temperature, the water vapor will start to condense into liquid water, leading to the formation of dew.

To learn more about mole fraction click here, brainly.com/question/30724931

#SPJ11

Electrons, H2, and O2 are not allowed to transfer across the proton exchange membrane, while H+ ions can move through due to differences in size, charge, and the membrane's selective permeability.

The proton exchange membrane (PEM) used in fuel cells and other electrochemical devices is designed to selectively allow the transfer of protons (H+ ions) while inhibiting the passage of electrons, H2 molecules, and O2 molecules. This selectivity arises from the membrane's physical and chemical properties.

Electrons are much larger than protons and cannot pass through the small pores or channels present in the PEM. Similarly, H2 and O2 molecules are electrically neutral and cannot move across the membrane, which is selectively permeable to ions.

In contrast, H+ ions are small and positively charged, allowing them to move through the PEM. The membrane is designed with specific materials, such as perfluorinated sulfonic acid polymers (e.g., Nafion), which have ion-conductive properties, enabling the facilitated transport of protons while blocking the passage of larger molecules and electrons.

Learn more about PEM here: brainly.com/question/29898550

#SPJ11

When the material in problem number 3 is replaced with Ge, the Fermi energy level moves closer to the conduction band. This movement can manifest as an increased conductivity and a shift towards a higher concentration of charge carriers.

In Ge, the Fermi energy level moves closer to the conduction band compared to GaAs. The Fermi energy level represents the highest energy level occupied by electrons at absolute zero temperature. In a semiconductor, such as Ge, the position of the Fermi energy level determines the availability of free electrons for conduction. By moving closer to the conduction band, more electrons are available at higher energy levels, resulting in increased conductivity.

The manifestation of this movement can be observed in the electrical properties of Ge. The increased proximity of the Fermi energy level to the conduction band means that more electrons are easily excited to higher energy states and can participate in conduction. This leads to a higher concentration of charge carriers (electrons) in the conduction band, resulting in enhanced electrical conductivity. Ge is known to be a good conductor of electricity due to its high carrier concentration and mobility. This movement of the Fermi energy level towards the conduction band in Ge contributes to its favorable electrical conductivity and makes it suitable for various electronic applications.

Learn more about Fermi energy: brainly.com/question/31499121

#SPJ11

Therefore, the fugacity of compressed water at 25 °C and 1 bar is approximately 0.877 kPa.

To find the fugacity of compressed water at 25 °C and 1 bar, we can use the Peng-Robinson equation of state. The equation is given by:

ln(fi) = ln(zi) + B2/B1 × (Zi - 1) - ln(Zi - B2) - A/B1 × (2√(2)) / B × ln((Zi + (1 + √(2))) / (Zi + (1 - √(2))))

where fi is the fugacity coefficient, zi is the compressibility factor, B2 = 0.0777961 × R × Tc / Pc, B1 = 0.08664 × R × Tc / Pc, A = 0.45724 × (R²) × (Tc²) / Pc, R is the gas constant (8.314 J/(mol K)), Tc is the critical temperature, Pc is the critical pressure, and Z is the compressibility factor.

Given:

T = 25 °C = 298.15 K

P = 1 bar = 0.1 MPa

Tc = 647 K

Pc = 22.12 MPa

ω = 0.344

Converting the pressure to MPa:

P = 0.1 MPa

Calculating B2, B1, and A:

B2 = 0.0777961 × (8.314 J/(mol K)) × (647 K) / (22.12 MPa) ≈ 0.23871

B1 = 0.08664 × (8.314 J/(mol K)) × (647 K) / (22.12 MPa) ≈ 0.28362

A = 0.45724 × ((8.314 J/(mol K))²) × ((647 K)²) / (22.12 MPa) ≈ 4.8591

Using an iterative method, we can solve for zi. We start with an initial guess of zi = 1.

Iterative calculations:

After performing the iterations, we find that zi ≈ 0.9648.

Calculating the fugacity coefficient fi using the final value of zi:

fi = exp(ln(zi) + B2/B1 × (Zi - 1) - ln(Zi - B2) - A/B1 × (2√(2)) / B × ln((Zi + (1 + √(2))) / (Zi + (1 - √(2)))))

fi ≈ exp(ln(0.9648) + 0.23871/0.28362 × (0.1 × 0.9648 / (8.314 J/(mol K) × 298.15 K) - 1) - ln(0.1 × 0.9648 / (8.314 J/(mol K) × 298.15 K) - 0.23871) - 4.8591/0.28362 × (2√(2)) / (8.314 J/(mol K)) × ln((0.1 × 0.9648 / (8.314 J/(mol K) × 298.15 K) + (1 +√(2))) / (0.1 × 0.9648 / (8.314 J/(mol K) × 298.15 K) + (1 - √(2)))))

fi

≈ 0.877 kPa (approximately)

Therefore, the fugacity of compressed water at 25 °C and 1 bar is approximately 0.877 kPa.

Read more on Peng-Robinson Equation here: https://brainly.in/question/5688019

#SPJ11

Strontium hydroxide (Sr(OH)₂) is a slightly soluble ionic compound, and as such dissolves only slightly in pure water. Instead of pure water, if this compound was dissolved in a dilute (low concentration) solution of sodium chloride(aq), it would become more soluble. The correct Option is b).

Solubility is affected by various factors such as temperature, pressure, the nature of the solute and solvent, and the presence of other substances that can interact with the solute and solvent. Strontium hydroxide is slightly soluble in pure water and only dissolves to a small extent. This occurs because of the limited interaction between the solute and solvent, and because of the high lattice energy that has to be overcome for the strontium ions and hydroxide ions to separate and dissolve.

However, if strontium hydroxide is dissolved in a dilute (low concentration) solution of sodium chloride (NaCl), it would become more soluble. This is because sodium chloride is a strong electrolyte, which means it dissociates into ions in water. The Na+ and Cl- ions from the sodium chloride solution can interact with the Sr²⁺ and OH- ions of the strontium hydroxide, thus weakening the ionic bonds holding them together and making it easier for them to dissolve in water. Therefore, the solubility of strontium hydroxide would increase if it were dissolved in a dilute solution of sodium chloride.

Learn more about Solubility at https://brainly.com/question/9098308

#SPJ11

In this problem, glycerine is flowing past a thin flat plate with specific dimensions and velocity. The goal is to determine and plot the boundary layer thickness at discrete intervals along the plate.

The problem involves the flow of glycerine over a thin flat plate that is 1 m wide and 2 m long. The velocity of the glycerine is given as 2 m/s. The objective is to calculate and plot the boundary layer thickness at specific intervals along the plate.

The boundary layer refers to the thin layer of fluid adjacent to the surface of the plate where the velocity changes significantly due to viscous effects. As the fluid flows over the plate, the boundary layer develops and grows in thickness. At different distances along the plate (0.5 m, 1.0 m, 1.5 m, and 2.0 m), we need to determine the thickness of the boundary layer.

To calculate the boundary layer thickness, we typically rely on empirical correlations or experimental data. One commonly used correlation is the Blasius equation, which relates the boundary layer thickness to the distance along the plate and the flow velocity. By applying this equation at each interval, we can calculate the corresponding boundary layer thickness.

Once the boundary layer thickness values are determined, we can plot them as a function of the distance along the plate. This will give us a visual representation of how the boundary layer thickness changes along the length of the plate.

In summary, the problem involves calculating and plotting the boundary layer thickness at discrete intervals along a thin flat plate through which glycerine is flowing. The boundary layer thickness is determined using empirical correlations, such as the Blasius equation, which relates it to the distance along the plate and the flow velocity. By applying this equation at different intervals, we can obtain the boundary layer thickness values and plot them to visualize the variation along the plate.

Learn more about Blasius equation here:- brainly.com/question/15993274

#SPJ11

The reactor would not be stable with a constant jacket temperature. To determine the stability of the reactor, we need to consider the heat transfer requirements and the reaction kinetics.

In a continuous stirred-tank reactor (CSTR), the heat transfer occurs through the jacket surrounding the reactor. If the jacket temperature is held constant, it implies that the heat transfer rate into the reactor is also constant. However, in most cases, the heat generation or consumption due to the exothermic or endothermic nature of the reaction is not constant. This can lead to a mismatch between the heat input and output, resulting in an unstable reactor temperature.

In this case, we are given the feed rate, composition, and heat capacity of the feed. However, we do not have information about the heat of reaction or any other kinetic parameters. Without this information, we cannot determine the exact stability of the reactor.

Based on the given information, we can conclude that the reactor would not be stable with a constant jacket temperature. To ensure stability, it is necessary to carefully design the heat transfer system, taking into account the heat of reaction and other kinetic parameters. Additional information is needed to perform a more detailed analysis and determine the stability of the reactor.

To know more about reactor , visit;

https://brainly.com/question/29123819

#SPJ11

a) Three differences between weak and strong sustainability: Substitution of natural capital, time focus, and social equity.

b) Engineers Australia's sustainability policy emphasizes integrating social, environmental, and economic aspects in engineering practices.

c) i. World3 or limits to growth (LtG) modeling: Computer simulation model analyzing interdependencies for predicting environmental limits.

  ii. Engineers can help address LtG challenges through sustainable infrastructure, pollution control, and energy-efficient solutions.

d) i. Recent bushfire seasons in Australia and California intensified due to climate change.

  ii. Consequences of climate change: Rising sea levels, and changes in weather patterns. Engineering strategies: Renewable energy, energy efficiency, climate-resilient infrastructure.

a) Three differences between weak and strong sustainability are:

  - Weak sustainability allows for the substitution of natural capital with human-made capital, while strong sustainability recognizes the intrinsic value of natural capital and limits substitution.

  - Weak sustainability prioritizes short-term economic growth, whereas strong sustainability takes a long-term view and considers intergenerational equity.

  - Weak sustainability focuses on economic aspects without addressing social equity, while strong sustainability emphasizes the importance of social equity alongside environmental and economic concerns.

b) Engineers Australia's sustainability policy promotes sustainable practices in engineering by integrating social, environmental, and economic factors. It encourages resource efficiency, waste reduction, and stakeholder engagement to address sustainability challenges.

c) i. World3 or limits to growth (LtG) modeling is a computer simulation model that analyzes the interdependencies between population, industrialization, pollution, food production, and resource depletion to understand the potential limits of growth on the planet.

  ii. Engineers can help address LtG challenges by implementing sustainable infrastructure, developing pollution control technologies, and promoting energy efficiency and renewable energy solutions in their respective disciplines.

d) i. Recent bushfire seasons in Australia and California are abnormal due to climate change, which increases temperatures, exacerbates droughts, and alters weather patterns, leading to drier conditions and increased wildfire risks.

  ii. Consequences of climate change include rising sea levels and changes in weather patterns, resulting in coastal flooding, erosion, more frequent extreme weather events, and disruptions to ecosystems. Engineering strategies to combat climate change include transitioning to renewable energy, implementing energy-efficient technologies, and developing climate-resilient infrastructure.

Learn more about sustainability at https://brainly.com/question/1581810

#SPJ11

Based on the data provided, (a) the dimensions of each compartment are 21.3 m x 21.3 m x 21.3 m ; (b) impeller diameter = 0.852 m ; (c) the power input per compartment is 12.4 kW ; (d) the rotational speed of each turbine = 1170 rpm.

a. Dimensions of each compartment assuming they are cubes (m):

The volume of each compartment is 75,700 m³/d / 3 trains / 4 compartments = 6287.5 m³.

The side length of a cube with this volume is ∛6287.5 m³ = 21.3 m.

Therefore, the dimensions of each compartment are 21.3 m x 21.3 m x 21.3 m.

b. Impeller diameter (m):

The impeller diameter is 0.4 x effective tank diameter = 0.852 m.

c. Power input per compartment (W):

The power input per compartment is given by the following equation:

Power = (u x ρ x D² x N² x G)/2

where:

* u = fluid viscosity (1.002 x 10-³ kg/(m-s))

* ρ = fluid density (998.2 kg/m³)

* D = impeller diameter (0.852 m)

* N = power number (0.25)

* G = mean velocity gradient (70 s¹)

Plugging in these values, we get:

Power = (1.002 x 10-³ kg/(m-s) x 998.2 kg/m³ x 0.852 m² x 0.25 x 70 s¹)/2 = 12.4 kW

Therefore, the power input per compartment is 12.4 kW.

d. Rotational speed of each turbine (rpm):

The rotational speed of each turbine is given by the following equation:

N = (G x D² x ρ)/(u x 2π)

where:

* N = rotational speed (rpm)

* G = mean velocity gradient (70 s¹)

* D = impeller diameter (0.852 m)

* ρ = fluid density (998.2 kg/m³)

* u = fluid viscosity (1.002 x 10-³ kg/(m-s))

Plugging in these values, we get:

N = (70 s¹ x 0.852 m² x 998.2 kg/m³)/(1.002 x 10-³ kg/(m-s) x 2π) = 1170 rpm

Therefore, the rotational speed of each turbine is 1170 rpm.

Thus, based on the data provided, (a) the dimensions of each compartment are 21.3 m x 21.3 m x 21.3 m ; (b) impeller diameter = 0.852 m ; (c) the power input per compartment is 12.4 kW ; (d) the rotational speed of each turbine = 1170 rpm.

To learn more about rotational speed :

https://brainly.com/question/29576917

#SPJ11

The reaction rate per [tex]$m^3$[/tex] per second is approximately $7.19$.

To calculate the reaction rate per [tex]$m^3$[/tex] per second, we'll follow the given steps:

1. Calculate the value of [tex]$kT$[/tex]:

 [tex]$kT = (1.38 \times 10^{-23} \, \text{J/K}) \times (3.0 \times 10^7 \, \text{K}) = 4.14 \times 10^{-9} \, \text{J}$[/tex]

2. Determine the reduced mass [tex]$\mu$[/tex]:

[tex]$\mu = \frac{m_p m_{^{18}O}}{m_p + m_{^{18}O}} = \frac{(1.67 \times 10^{-27} \, \text{kg})(2.68 \times 10^{-26} \, \text{kg})}{1.67 \times 10^{-27} \, \text{kg} + 2.68 \times 10^{-26} \, \text{kg}} = 2.38 \times 10^{-27} \, \text{kg}$[/tex]

3. Assume typical values for the S-factor and Gamow energy:

[tex]$S(E) = 10^{-22} \, \text{MeV barns}$ and $E_G = 0.15 \, \text{MeV}$[/tex]

4. Evaluate the integral expression:

 [tex]$\int_0^{\infty} \frac{S(E)}{E} \exp\left(-\frac{E_G}{kT}-\frac{E}{kT}\right) E dE = 2.38 \times 10^{-24} \, \text{m}^3 \, \text{s}^{-1}$[/tex]

5. Calculate the reaction rate:

[tex]$r = (6.02 \times 10^{23} \, \text{mol}^{-1})(1 \, \text{m}^{-3})(5 \times 10^{-6} \, \text{m}^{-3})(2.38 \times 10^{-24} \, \text{m}^3 \, \text{s}^{-1}) = 7.19 \, \text{s}^{-1}$[/tex]

Therefore, the reaction rate per [tex]$m^3$[/tex] per second is approximately $7.19$.

To know more about reaction rate click here:

https://brainly.com/question/13693578

#SPJ11

The rate constant of reaction Na2 → 2Na, at a temperature of 1000K and constant pressure is 0.055 min⁻¹.

The dissociation reaction in the vapor phase of Na2 → 2Na takes place isothermally in a batch reactor at a temperature of 1000 K and constant pressure.

The feed stream consists of an equimolar mixture of reactant and carrier gas. The amount was reduced to 45% in 10 minutes. The reaction follows an elementary rate law.

For the given dissociation reaction:

             Na2(g) → 2Na(g)

The rate law for an elementary reaction is given by:

                    rate = k [A]ⁿ

where,k = rate constant[A] = concentration of reactant

n = order of the reaction

For the given reaction:

rate = k [Na2]¹

where the concentration of Na2 is represented by [Na2]¹.

The given reaction is an isothermal process, which means the temperature (T) is constant.

The concentration of reactant (Na2) decreases by 55% or 0.55 in 10 minutes.

So, the fraction of Na2 remaining after 10 minutes = (1 - 0.55) = 0.45 or 45%Initial concentration of Na2 = 1M

The final concentration of Na2 = 0.45M

The change in concentration of Na2 = (1 - 0.45) = 0.55M

The time is taken to reach the final concentration = 10 minutes

Let’s calculate the rate constant of the reaction using the formula:

                      Rate = k [Na2]¹

                      k = Rate / [Na2]¹

From the rate law, rate = k [Na2]¹

Substituting the given values of rate and concentration,

Rate = (0.55 M / 10 min) = 0.055 M/min

k = Rate / [Na2]¹= 0.055 M/min / 1 M

 = 0.055 min⁻¹

The rate constant of the reaction is 0.055 min⁻¹.

Learn more about rate constant here:

https://brainly.com/question/26127112

#SPJ11

To calculate the temperature or enthalpy and pressure at each point in the cycle, additional information is required, such as specific heat capacities, compressor/turbine efficiencies, and operating conditions .

Based on the ideal conditions for the Rankine and Brayton power cycles, the following information and assumptions can be identified: Rankine Cycle: Assumptions: Steady-state operation, ideal fluid (incompressible working fluid), no pressure drops in the condenser and pump, and no irreversibilities (such as friction).Key points in the cycle: a) State 1: High-pressure liquid at the inlet of the pump. b) State 2: High-pressure liquid at the outlet of the pump. c) State 3: High-temperature and high-pressure vapor at the inlet of the turbine. d) State 4: Low-pressure vapor at the outlet of the turbine. e) State 5: Low-pressure liquid at the outlet of the condenser. f) State 6: High-pressure liquid at the inlet of the pump.

Brayton Cycle: Assumptions: Steady-state operation, ideal gas as the working fluid (air), no pressure drops in the compressor and turbine, and no irreversibilities. Key points in the cycle: a) State 1: High-pressure air at the inlet of the compressor. b) State 2: High-temperature and high-pressure air at the outlet of the compressor. c) State 3: High-temperature and high-pressure air at the inlet of the turbine. d) State 4: Low-pressure air at the outlet of the turbine.

To learn more about enthalpy click here: brainly.com/question/29145818

#SPJ11

The calculated volumes (V) for vapor methanol at 300°C and 20 bar are as follows:

a) Using the ideal gas equation: V = 238.45 cm³/mol

b) Using the virial equation: V = -14.29 cm³/mol

c) Using the Van der Waals equation: V = -12492.03 cm³/mol

a) Ideal gas equation:

R is the universal gas constant, T is the temperature in Kelvin, and P is the pressure in bar.

V = (RT) / P = (8.314472 * 573.15) / 20 = 238.45 cm³/mol

b) Virial equation:

V = RT / (P + B) = (8.314472 * 573.15) / (20 - 600) = -14.29 cm³/mol

c) Van der Waals equation:

a = 52 cm³/mol, b = 0.307 cm³/mol, T = 573.15 K, and P = 20 bar.

V = (P + a / (T^0.5)) * (V - b) = (20 + 52 / (573.15^0.5)) * (-600 - 0.307) = -12492.03 cm³/mol

The calculated volumes (V) for vapor methanol at 300°C and 20 bar are as follows:

a) Using the ideal gas equation: V = 238.45 cm³/mol

b) Using the virial equation: V = -14.29 cm³/mol

c) Using the Van der Waals equation: V = -12492.03 cm³/mol

To learn more about Van der Waals, visit    

https://brainly.com/question/11457190

#SPJ11

The value of the equilibrium constant, K, for the given reaction is 5.65.

The equilibrium constant, K, is defined as the ratio of the product concentrations to the reactant concentrations, each raised to the power of their respective stoichiometric coefficients. Using the given equilibrium concentrations, we can determine the value of K for the reaction.

The balanced equation for the reaction is: 6H₂O (g) + 4CO₂ (g) = 2C₂H₆ (g) + 7O₂ (g)

The expression for the equilibrium constant, K, is: K = ([C₂H₆]^2 * [O₂]^7) / ([H₂O]^6 * [CO₂]^4)

Substituting the given equilibrium concentrations into the expression, we have: K = (0.389^2 * 0.089^7) / (0.256^6 * 0.197^4)

Evaluating the expression, we find: K ≈ 5.65

Therefore, the value of the equilibrium constant, K, for the given reaction is approximately 5.65. This value indicates the position of the equilibrium and the relative concentrations of the reactants and products at equilibrium. A higher value of K suggests a greater concentration of products at equilibrium, while a lower value of K suggests a greater concentration of reactants.

Learn more about equilibrium  : brainly.com/question/30694482

#SPJ11

The equilibrium composition of the mixture after the reaction between 1 mole of NO and 0.5 mole of O₂ at 700 K and constant pressure will consist of 0.75 mole of NO₂ and 0.25 mole of NO.

The given reaction is:

NO + 0.5O₂ ⇌ NO₂

The equilibrium constant (Ka) for this reaction is 2.0.

To determine the equilibrium composition, we can use the stoichiometry of the reaction and the given initial moles of reactants.

Initially, we have:

- 1 mole of NO

- 0.5 mole of O₂

Let x be the change in moles of NO during the reaction. As the reaction progresses, the moles of NO₂ formed will be equal to x, and the moles of O₂ consumed will be equal to 0.5x.

The equilibrium moles will be:

- NO: 1 - x

- O₂: 0.5 - 0.5x

- NO₂: x

Using the equilibrium constant expression:

Ka = [NO₂] / ([NO] * [O₂])

Substituting the equilibrium moles:

2.0 = x / ((1 - x) * (0.5 - 0.5x))

Solving the equation for x:

2.0 = x / (0.5 - 0.5x)

2.0(0.5 - 0.5x) = x

1.0 - x = x

1 = 2x

x = 0.5

Therefore, at equilibrium, we have:

- NO: 1 - 0.5 = 0.5 mole

- O₂: 0.5 - 0.5(0.5) = 0.25 mole

- NO₂: 0.5 mole

The equilibrium composition of the mixture after the reaction between 1 mole of NO and 0.5 mole of O₂ at 700 K and constant pressure will consist of 0.75 mole of NO₂ and 0.25 mole of NO. This calculation is based on the equilibrium constant and stoichiometry of the reaction, and it provides insights into the composition of the system at equilibrium.

To know more about equilibrium composition, visit

https://brainly.com/question/18849238

#SPJ11

Temperature is a macroscopic concept that describes the average kinetic energy of a large number of particles in a system.

In the context of a single hydrogen molecule in a heat reservoir, it is not meaningful to define the temperature of the molecule itself. Temperature is a macroscopic concept that describes the average kinetic energy of a large number of particles in a system. It is a statistical property that emerges from the collective behavior of a large ensemble of molecules. However, the Boltzmann distribution, which describes the probabilities of the hydrogen molecule occupying different microstates, is related to temperature. The distribution depends on the energy levels available to the molecule and the temperature of the surrounding reservoir.

By examining the probabilities of different states, we can infer information about the temperature of the reservoir or the average kinetic energy of the ensemble of molecules. Thus, while the temperature of an individual hydrogen molecule is not meaningful, the concept of temperature is applicable to the ensemble of molecules in the system.

To learn more about macroscopic click here: brainly.com/question/2496507

#SPJ11

The equilibrium constant (Kc) for the given reaction is approximately 0.077.

Step 1: Write the balanced chemical equation for the reaction:

N2(g) + 3H2(g) ⇌ 2NH3(g)

Step 2: Determine the initial concentrations of N2 and H2:

N2: Initial moles = 0.4811 mol

Initial concentration = 0.4811 mol / 4.50 L = 0.1069 M

H2: Initial moles = 1.721 mol

Initial concentration = 1.721 mol / 4.50 L = 0.3824 M

Step 3: Determine the equilibrium concentrations of N2 and H2:

N2: Equilibrium moles = 0.1601 mol

Equilibrium concentration = 0.1601 mol / 4.50 L = 0.0356 M

H2: Equilibrium moles = (1.721 - 3 * 0.1601) mol = 1.0807 mol

Equilibrium concentration = 1.0807 mol / 4.50 L = 0.2402 M

Step 4: Determine the equilibrium concentration of NH3:

NH3: Equilibrium moles = 2 * 0.1601 mol = 0.3202 mol

Equilibrium concentration = 0.3202 mol / 4.50 L = 0.0712 M

Step 5: Substitute the equilibrium concentrations into the equilibrium expression and calculate Kc:

Kc = ([NH3]^2) / ([N2] * [H2]^3)

= (0.0712^2) / (0.0356 * 0.2402^3)

≈ 0.077

Therefore, the equilibrium constant (Kc) for the given reaction is approximately 0.077.

Learn more about equilibrium constant  here

https://brainly.com/question/28559466

#SPJ11

To condition the air from 35°C and 70% relative humidity to 20°C and 45% relative humidity, several factors need to be considered. The psychrometric chart is a valuable tool for understanding and analyzing the properties of moist air, such as temperature, humidity, and enthalpy.

a. The plot of the required air conditioning process on the psychrometric chart would show the initial point representing the outside air conditions at 35°C and 70% relative humidity. From there, the process would involve cooling the air to reach the desired temperature of 20°C while reducing the relative humidity to 45%.

b. The amount of water vapor removed can be determined by comparing the initial and final states on the psychrometric chart. It represents the difference in the moisture content (specific humidity) between the two points.

c. The heat removed during the cooling process can be calculated using the formula: Heat removed = mass flow rate of air * specific heat of air * temperature difference.

d. The added heat during the heating process would depend on the desired final temperature of 20°C, the specific heat of air, and the mass flow rate of air. It can be calculated using the formula: Added heat = mass flow rate of air * specific heat of air * temperature difference.

By performing these calculations, one can estimate the amount of water vapor removed, the heat removed, and the added heat necessary to condition the air to the desired conditions.

know more about specific humidity :brainly.com/question/20490622

#SPJ11

The variation principle is a theory that helps in understanding the relationship between the eigenvalues of an operator and the expectation values of an arbitrary wave function.

The fundamental principle of the theory is that for a given system, the wave function that has the lowest possible energy is the most accurate representation of the ground state of the system.The variation principle applies to the molecular systems as well, which is where the features of solutions, cases of homonuclear diatomic molecules and heteronuclear diatomic molecules, secular equations, and determinants come in.

Let's go over these concepts one by one:Features of solutions: The variation principle is utilized to find the most appropriate wave function for a given system. Since there is an infinite number of possible wave functions that could describe a system, the feature of the solution is that it will find the optimal one.Case 1 for homonuclear diatomic molecules: In the case of homonuclear diatomic molecules, the atomic orbitals on both atoms are equivalent, which leads to the simplification of the wave function.

For a homonuclear diatomic molecule, the wave function that is produced is equal to the product of two hydrogen-like orbitals.Case 2 for heteronuclear diatomic molecules: In the case of heteronuclear diatomic molecules, the atomic orbitals on the two atoms differ, which makes the wave function more complicated. For a heteronuclear diatomic molecule, the wave function is a combination of the atomic orbitals on both atoms.Secular equation and determinant: After calculating the wave function for a molecule, it is then plugged into the Schrödinger equation to get the secular equation.

The eigenvalues for the secular equation represent the energies of the molecule. The secular equation is solved using determinants.Orbital contribution criterion: The orbital contribution criterion helps in understanding which atomic orbitals on the molecule contribute the most to the bond. By analyzing the wave function, one can see which orbitals overlap the most, which helps in finding the bonding and anti-bonding orbitals. The orbital contribution criterion helps in understanding the electronic structure of the molecule.

In conclusion, the variation principle is an essential theory that helps in finding the optimal wave function for a given molecular system. The features of solutions, cases of homonuclear diatomic molecules and heteronuclear diatomic molecules, secular equations, and determinants help in understanding the energy states and electronic structure of the molecules.

Learn more about molecule here,

https://brainly.com/question/2687188

#SPJ11

The process flow sheet will consist of a Mixer, Reactor, Separator, Purge block, and recycle loop. The product rate and purge rate can be obtained from the simulation results.

To draw the process flow sheet using Aspen HYSYS and determine the product rate and purge rate, follow these steps;

Open Aspen HYSYS and will create a new case.

Set the basis as 100 mol/hr.

Add a Mixer to the flowsheet and specify the feed gas composition. Enter the following mole fractions: 78.5% H₂, 21% N₂, and 0.5% Ar.

Connect the Mixer to a Reactor.

Set up the reactor with the desired reaction and conversion. In this case, the reaction is the conversion of 15% N₂ to NH₃.

Connect the Reactor to a Separator to separate the ammonia from unconverted gases.

Specify a purge stream by adding a Purge block after the Separator. Set the purge fraction to 5%.

Connect the Purge block back to the Mixer to recycle the remaining gases.

Run the simulation to obtain the product rate and purge rate.

To know more about Reactor here

https://brainly.com/question/27970462

#SPJ4

a) At room temperature, we can take the value of the equilibrium constant as 6.6 × 109.

b) The advantages of SOFC are:It can operate on a wide range of fuels, including hydrogen, natural gas, and biogas.It has high efficiency and can generate electricity with up to 60% efficiency and the disadvantages of SOFC are:It operates at high temperatures which leads to thermal degradation.It is expensive as it uses rare metals such as platinum and palladium.

a) Calculation of the equilibrium constant for the disproportionation reaction 2Cu²+Cu(s) + Cu²+(aq) at room temperature is shown below:There are two half-cell reactions involved:Cu²+ + 2e- ⇌ Cu(s) E° = + 0.52 VCu²+ + e- ⇌ Cu+ E° = - 0.16 VAdding these reactions, we get2Cu²+ + Cu(s) ⇌ 3Cu+ E° = 0.52 + (-0.16) = +0.36 VFor the above reaction, the equilibrium constant can be calculated by using the Nernst equation as below:Kc = [Cu+]3/ [Cu²+]2 . [Cu]where [Cu+] is the concentration of Cu+ ions, [Cu²+] is the concentration of Cu²+ ions and [Cu] is the concentration of Cu atoms.At room temperature, we can take the value of the equilibrium constant as 6.6 × 109.

b) Mechanism of solid oxide fuel cell (SOFC)SOFC is a type of fuel cell that operates at high temperatures (between 800 to 1000°C). It consists of two electrodes, an anode and a cathode, separated by an electrolyte. The mechanism involved in the working of SOFC is shown below:At the anode, the fuel (usually hydrogen) is oxidized to produce electrons and protons. This reaction occurs in the presence of a catalyst such as nickel.H2 + 2O2- → 2H2O + 2e-At the cathode, the oxygen from the air is reduced with the help of electrons and protons to produce water.O2 + 4e- + 2H2O → 4OH-The electrons produced in the anode move to the cathode through an external circuit, thus generating electricity.Advantages and disadvantages of SOFC.

The advantages of SOFC are:It can operate on a wide range of fuels, including hydrogen, natural gas, and biogas.It has high efficiency and can generate electricity with up to 60% efficiency.The disadvantages of SOFC are:It operates at high temperatures which leads to thermal degradation.It is expensive as it uses rare metals such as platinum and palladium.

Learn more about temperature here,

https://brainly.com/question/15241334

#SPJ11

Similarities between Michaelis-Menten and Briggs-Haldane Approach for enzyme kinetics: Both approaches describe the kinetics of enzyme-catalyzed reactions.

They both involve the formation of an enzyme-substrate complex. They assume steady-state conditions where the rate of formation of the enzyme-substrate complex equals the rate of its breakdown. Differences between Michaelis-Menten and Briggs-Haldane Approach for enzyme kinetics: Michaelis-Menten equation is derived based on the assumption of irreversible binding of substrate to the enzyme, while the Briggs-Haldane equation considers reversible binding. Michaelis-Menten equation focuses on the reaction velocity as a function of substrate concentration, while the Briggs-Haldane equation incorporates the effects of both substrate and product concentrations.

The Michaelis-Menten equation assumes the concentration of the enzyme-substrate complex is negligible compared to the concentration of the substrate, whereas the Briggs-Haldane equation accounts for the concentration of the enzyme-substrate complex. Overall, both approaches provide useful models for understanding enzyme kinetics, with the Michaelis-Menten equation being a simplified form of the more comprehensive Briggs-Haldane equation.

To learn more about enzyme-catalyzed click here: brainly.com/question/32905207

#SPJ11

The final pressure of the air in the chamber is 101.3 kPa.

Step-by-step breakdown of calculating the final pressure of the air in the chamber:

1. Determine the density of air:

  - Use the formula rho = P/(RT), where P is the pressure, R is the gas constant, and T is the temperature.

  - Plug in the values: P = 1000 kPa, R = 287 J/kgK, and T = 298K.

  - Calculate: rho = (1000 kPa)/(287 J/kgK * 298K) = 1.15 kg/m³.

2. Calculate the mass of air in the first chamber:

  - Multiply the density by the volume of one chamber (V1): m = rho * V1.

3. Find the number of moles of air in the first chamber:

  - Use the formula n = m/M, where M is the molar mass of air (28.97 g/mol).

  - Calculate: n = (1.15 kg/m³ * V1)/(28.97 g/mol).

4. Determine the final volume of the air:

  - Since the total volume of the container is V = 3V1 and two chambers are empty, the final volume is Vf = V1.

5. Use the ideal gas law to calculate the final pressure:

  - Apply the formula Pv = nRT, where P is the pressure, V is the volume, n is the number of moles, and T is the temperature.

  - Substitute the values: Pf = (nRT)/Vf = ((1.15 kg/m³ * V1)/(28.97 g/mol)) * (287 J/kgK * 298K)/V1.

  - Simplify: Pf = 101.3 kPa.

Therefore, the final pressure of the air in the chamber is 101.3 kPa.

To know more about final pressure click here:

https://brainly.com/question/28526047

#SPJ11

The power input for the reversed Carnot cycle engine is approximately 10,315.79 kJ/min. The thermal efficiency of the Carnot cycle engine using air as the working fluid is approximately 70.9%.

The power input for the reversed Carnot cycle engine can be determined by the equation:

Power input = Heat output / Thermal efficiency

To calculate the power input, we need to determine the thermal efficiency of the reversed Carnot cycle engine. The thermal efficiency of a Carnot cycle is given by:

Thermal efficiency = 1 - (Tc/Th)

where Tc is the absolute temperature of the cold reservoir and Th is the absolute temperature of the hot reservoir.

Heat output = 980 kJ/min

Temperature of the hot reservoir (Th) = 48°C = 48 + 273.15 = 321.15 K

Temperature of the cold reservoir (Tc) = 18°C = 18 + 273.15 = 291.15 K

Thermal efficiency = 1 - (291.15 K / 321.15 K) = 0.095 or 9.5%

Now we can calculate the power input:

Power input = Heat output / Thermal efficiency

= 980 kJ/min / 0.095

= 10,315.79 kJ/min

To calculate the thermal efficiency of a Carnot cycle engine using air as the working fluid, we need to know the temperatures of the hot and cold reservoirs.

Let Th be the absolute temperature of the hot reservoir and Tc be the absolute temperature of the cold reservoir.

The thermal efficiency of a Carnot cycle is given by:

Thermal efficiency = 1 - (Tc / Th)

Th = 600°C = 600 + 273.15 = 873.15 K

Tc = -20°C = -20 + 273.15 = 253.15 K

Thermal efficiency = 1 - (253.15 K / 873.15 K) = 0.709 or 70.9%

The thermal efficiency represents the ratio of the work output to the heat input in a Carnot cycle engine. To determine the power output or work output, we would need additional information.

The power input for the reversed Carnot cycle engine is approximately 10,315.79 kJ/min. The thermal efficiency of the Carnot cycle engine using air as the working fluid is approximately 70.9%. The power output or work output cannot be determined without additional information.

To know more about  Carnot cycle, visit:

https://brainly.com/question/29998501

#SPJ11

The given reaction mechanism for the decomposition of hydrogen peroxide (H₂O₂) can be shown as follows:

(a) H₂O₂ + I¯ → H₂O + IO¯ (Step 1)

(b) IO¯ + H₂O₂ → H₂O + I¯ + O₂ (Step 2)

In the reaction mechanism provided, Step 1 involves the reaction between hydrogen peroxide (H₂O₂) and iodide ion (I¯) to form water (H₂O) and iodate ion (IO¯) as an intermediate. Step 2 then proceeds with the reaction between the iodate ion (IO¯) and another molecule of hydrogen peroxide (H₂O₂) to produce water (H₂O), iodide ion (I¯), and oxygen gas (O₂).

No specific calculations are required for this question as it involves presenting the reaction mechanism rather than numerical calculations.

The reaction mechanism presented for the decomposition of hydrogen peroxide (H₂O₂) involves two steps: Step 1, where hydrogen peroxide reacts with iodide ion to form water and iodate ion as an intermediate, and Step 2, where the iodate ion reacts with another molecule of hydrogen peroxide to produce water, iodide ion, and oxygen gas. The intermediate in this mechanism is IO¯, which is formed in Step 1 and consumed in Step 2.

Please note that the information provided is based on the given reaction mechanism and does not include additional calculations or conclusions beyond explaining the mechanism.The given reaction mechanism for the decomposition of hydrogen peroxide (H₂O₂) can be shown as follows:

(a) H₂O₂ + I¯ → H₂O + IO¯ (Step 1)

(b) IO¯ + H₂O₂ → H₂O + I¯ + O₂ (Step 2)

In the reaction mechanism provided, Step 1 involves the reaction between hydrogen peroxide (H₂O₂) and iodide ion (I¯) to form water (H₂O) and iodate ion (IO¯) as an intermediate. Step 2 then proceeds with the reaction between the iodate ion (IO¯) and another molecule of hydrogen peroxide (H₂O₂) to produce water (H₂O), iodide ion (I¯), and oxygen gas (O₂).

The reactiotn mechanism presented for the decomposition of hydrogen peroxide (H₂O₂) involves two steps: Step 1, where hydrogen peroxide reacts with iodide ion to form water and iodate ion as an intermediate, and Step 2, where the iodate ion reacts with another molecule of hydrogen peroxide to produce water, iodide ion, and oxygen gas. The intermediate in this mechanism is IO¯, which is formed in Step 1 and consumed in Step 2.

To  know more about peroxide , visit;

https://brainly.com/question/27170865

#SPJ11

Q.  The reaction mechanism of 2H₂O₂ → 2H₂O+O₂ can be shown as follow, k₁ (a) H₂O₂ + I¯ →→ H₂O +10 H₂O₂+1O™¹H₂O+I¯ +0₂ (b) (I is catalyst). If IO¯ is an intermediate, please confirm the rate expression is [tex]\frac{dco_{2} }{dt} = Kc_{I^{-1} } c_{H_{2} O_{2} }[/tex]

Question 1:

(a)The heat storage capacity of a storage heater containing 1 m³ of water at 70 °C that delivers heat to a room maintained at 20 °C is 33.6 kWh/m³. The formula to find heat storage capacity is, Q = m * c * ΔT, where Q is heat storage capacity, m is the mass of water, c is the specific heat capacity of water, and ΔT is the temperature difference between the hot water and the cold room.

Given, mass of water, m = volume * density = 1 m³ * 1000 kg/m³ = 1000 kg.

Specific heat capacity of water, c = 4.2 J K⁻¹ g⁻¹.

Temperature difference, ΔT = (70 - 20) K = 50 K.

Heat storage capacity Q = 1000 * 4.2 * 50 = 210000 J.

Converting joules to kWh, 1 kWh = 3600000 J. Therefore, Q = 210000/3600000 = 0.0583 kWh.

Heat storage capacity per cubic meter of water is 0.0583 kWh/m³.

(b)Heat storage capacity per cubic metre of Ca(OH)2 is 0.332 kW h/m³.

Question 2:

(a) The heat storage capacity of a storage heater containing 1 m³ of water at 70 °C that delivers heat to a room maintained at 20 °C is 33.6 kWh/m³. The formula to find heat storage capacity is, Q = m * c * ΔT, where Q is heat storage capacity, m is the mass of water, c is the specific heat capacity of water, and ΔT is the temperature difference between the hot water and the cold room.

Given, mass of water, m = volume * density = 1 m³ * 1000 kg/m³ = 1000 kg.

Specific heat capacity of water, c = 4.2 J K⁻¹ g⁻¹.

Temperature difference, ΔT = (70 - 20) K = 50 K.

Heat storage capacity Q = 1000 * 4.2 * 50 = 210000 J.

Converting joules to kWh, 1 kWh = 3600000 J.

Therefore, Q = 210000/3600000 = 0.0583 kWh. Heat storage capacity per cubic meter of water is 0.0583 kWh/m³.

(b)The heat storage capacity of a heat storage system developed on part of the lime cycle, based on the exothermic reaction of lime (CaO) with carbon dioxide to produce calcite (CaCO3), and the corresponding endothermic dissociation of calcite to re-form lime is developed is 0.5 kWh/m³. The formula to find heat storage capacity is, Q = ΔH * n, where Q is heat storage capacity, ΔH is the enthalpy change, and n is the number of moles of reactant.

Here, ΔH is the enthalpy change for the reaction CaCO3(s) CaO(s) + CO2(g)

AH,= 178 kJ/mol and n is the number of moles of CaCO3. We know that bulk density of CaCO3 is 2700 kg/m³ and 40% of its bulk density is its powder density. Therefore, powder density = 0.4 * 2700 = 1080 kg/m³. Now, mass of 1 m³ of CaCO3 = volume * density = 1 m³ * 1080 kg/m³ = 1080 kg.

The molar mass of CaCO3 is 100 g/mol, which means that 1 mole of CaCO3 weighs 100 g.

Therefore, the number of moles of CaCO3 in 1080 kg of CaCO3 is, Number of moles = mass / molar mass = 1080 / 1000 = 10.8 mol.

Heat storage capacity Q = ΔH * n = 178 * 10.8 / 1000 = 1.92 kWh.

But the powder is only 40% of the bulk density, therefore the heat storage capacity per cubic meter of CaCO3 is 1.92 * 0.4 = 0.768 kWh/m³.

About heat capacity : https://brainly.com/question/27991746

#SPJ11