a) The required speed of the large fish just after it eats the small one is calculated to be 0.846 m/s.
b) The energy dissipated during this meal is calculated to be 2.097 J.
a) Mass of big fish is given as M = 15 kg
Mass of small fish m = 4.5 kg
The initial speed u of small fish is 0.
The initial speed of the big fish is 1.1 m/s.
From principle of conservation of linear momentum,
Total initial momentum = Total final momentum
Both the fish are said to have same final speed
M U + m u = (M + m) V
15 × 1.1 + 4.5 × 0 = (15 + 4.5) V
16.5 = 19.5 V
V = 16.5/19.5 = 0.846 m/s
Hence, the speed of the large fish after the meal is calculated as 0.846 m/s.
b) Let us calculate the mechanical energy dissipated,
Initial K.E = 1/2 M U² + 1/2 m u² = 1/2 × 15 × 1.1² + 1/2 × 4.5 × 0² = 9.075 J
Final K.E = 1/2 M V² + 1/2 m V² = 1/2 × 15 × 0.846² + 1/2 × 4.5 × 0.846² = 6.978 J
The change in kinetic energy is,
K.Efin - K.Eini = 9.075 - 6.978
ΔK.E = 2.097 J
Thus, the energy dissipated in eating this meal is 2.097 J.
The given question is incomplete. The complete question is 'The initial speed of the big fish is 1.1 m/s.'
To know more about speed:
https://brainly.com/question/15297133
#SPJ4
A plank is supported on flight of staircases.How
many forces are acting on the plank?
A 4
B 5
C 6
D 7
what should you do if you are driving 65 mph in the far left lane of a highway and everyone else in the lane is going 70 mph and above? a. nothing. since you are at the speed limit, it is their problem to move, not yours b. move to a lane that is more appropriate to your speed c. slow down so the drivers behind you will get the hint and slow down too d. flash the lights and honk the horn so the drivers behind you will get the hint and slow down
If you are driving 65 mph in the far left lane of a highway and everyone else in the lane is going 70 mph and above, you should move to a lane that is more appropriate to your speed. The correct answer is option b.
You should switch to a lane that's more suited for your pace If you're driving 65 mph in the far left lane of a highway and everyone else is travelling 70 mph or higher,
This is because the left lane is considered the passing lane in many states, and is generally used for faster-moving traffic. Slower traffic should stay in the right-hand lane or move over if they are in the left lane.
So, option (b) move to a lane that is more appropriate to your speed is correct.
For more such questions on speed, click on:
https://brainly.com/question/13943409
#SPJ11
Why is an ammeter always connected in series and a voltmeter always in parallel in a circuit?
An ammeter always connected in series and a voltmeter always in parallel in a circuit.
An ammeter is always connected in series because it is used to measure the current flowing through a particular part of a circuit. When an ammeter is connected in series, all of the current flowing through the circuit also flows through the ammeter. By measuring this current, the ammeter can provide an accurate reading of the current in that part of the circuit. If an ammeter were connected in parallel, it would change the resistance of the circuit and interfere with the current flow, giving an inaccurate reading.
A voltmeter is always connected in parallel because it is used to measure the voltage difference between two points in a circuit. When a voltmeter is connected in parallel, it is connected across the two points where the voltage difference is to be measured. This means that the voltmeter has a very high resistance, which ensures that it draws very little current from the circuit and does not affect the voltage being measured. If a voltmeter were connected in series, it would change the resistance of the circuit and interfere with the voltage being measured, giving an inaccurate reading.
Hence, an ammeter always connected in series and a voltmeter always in parallel in a circuit.
To know more about ammeter here
https://brainly.com/question/20379687
#SPJ1
If the roller coaster weighs 10,000kg and is traveling at 85 meters per second (m/s) what is the kinetic energy? Kinetic energy is measured in joules (j)?
Answer:
36,125KiloJoules.
Explanation:
K.E= 1/2MV².
that's 0.5 X 10,000 X 85.
which equals 36, 125, 000 Joules or 36,125 Kilo Joules.
Answer:
36,125,000 Joule is the answer according to the formula KE=1/2×m×(v)2
a force of 1 pounds is required to hold a spring stretched 0.1 feet beyond its natural length. how much work is done in stretching the spring from its natural length to 0.9 feet beyond its natural length? don't forget to enter the correct units. (you may enter lbf or lb*ft for ft-lb.) work
A force of 1 pounds is required to hold a spring stretched 0.1 feet beyond its natural length. The work done in stretching the spring from its natural length to 0.9 feet beyond its natural length is 4.05 lb*ft.
To calculate the work done in stretching the spring, we can use Hooke's Law and the work formula for a spring. Hooke's Law states that the force (F) required to stretch a spring is proportional to its displacement (x) from its natural length, represented as F = kx, where k is the spring constant.
From the given information, 1 pound of force is required to stretch the spring 0.1 feet. Therefore, we can find the spring constant k:
1 lb = k * 0.1 ft
k = 10 lb/ft
Now we can use the work formula for a spring: W = (1/2)kx^2, where W is the work done and x is the displacement from the natural length. In this case, we are stretching the spring 0.9 feet:
W = (1/2)(10 lb/ft)(0.9 ft)^2
W = 4.05 lb*ft
So, the work done is 4.05 lb*ft.
For more such questions on work done, click on:
https://brainly.com/question/25573309
#SPJ11
an ant of mass 1 gram clings to the rim of a flywheel of radius 0.4 m. the flywheel rotates clockwise on a horizontal shaft s at a constant rate of 2 revolutions per second. as the wheel rotates, the ant revolves past the stationary points i, ii, iii, and iv. the ant can adhere to the wheel with a force much greater than its own weight. what force must the ant hold on to stay on the wheel at point iii?
If the flywheel's rotational velocity is constant and the force applied by the ant is strong enough, the ant will adhere to the wheel's rim without slipping.
In this case, the ant's tangential velocity will be the same as the wheel's tangential velocity, and the centripetal force acting on the ant will be supplied by the frictional force.Using F = ma, we know that a = v^2/r. We can then substitute the value for the angular velocity and wheel radius to get the centripetal acceleration.
The centripetal force on the ant is m*ac. This centripetal force is supplied by the ant's grip on the wheel. Since the ant can hold on to the wheel with a force much greater than its own weight, it is safe to assume that the force of the grip is greater than the centripetal force.
In conclusion, the force with which the ant must hold on to stay on the wheel at point III is equal to the centripetal force exerted on it, which is equal to its mass multiplied by its centripetal acceleration, which is equal to m*v^2/r.
The mass of the ant is given as 1 gram (0.001 kg), and the radius of the wheel is given as 0.4 m. The linear velocity v can be calculated using the formula v = ωr. Therefore, the force required to keep the ant on the wheel at point III is:F = m*v^2/rF = 0.001*[(2*2*3.14*0.4)^2]/0.4F = 9.92 N (approximately)
To Learn More About Flywheel's
https://brainly.com/question/29452668
#SPJ11
every decade, the sea ice declines by 10 percent. if there were 6 million km2 of sea ice in the year 2000, how much would remain in 2020? group of answer choices
Option b. 4.86 million km2 of sea ice would remain in 2020 if the decline rate continued at 10% per decade.
Ocean ice is a significant piece of the World's environment framework, reflecting daylight and managing the planet's temperature. Be that as it may, environmental change has caused a decrease in how much ocean ice over ongoing many years, with a typical decay pace of around 10% each 10 years. This intends that for each decade that passes, how much ocean ice remaining is 90% of the earlier ten years' sum.
To work out how much ocean ice would stay in a specific year, we can utilize the recipe: remaining ice = (1-0.1)^n * beginning ice, where n is the quantity of many years that have passed and starting ice is how much ocean ice in the beginning year. For instance, in the event that there were 6 million km2 of ocean ice in the year 2000 and 20 years (twenty years) have passed, we can compute the excess ice in 2020 as follows: remaining ice = (1-0.1)^2 * 6 million km2, which approaches around 4.86 million km2.
This computation features the huge loss of ocean ice over a generally brief timeframe, with practically 20% of the ice vanishing more than twenty years. This deficiency of ocean ice has extensive ramifications for worldwide environment examples, natural life, and human networks living in the Cold.
To learn more about sea ice declining rate, refer:
https://brainly.com/question/3734286
#SPJ4
The complete question is:
every decade, the sea ice declines by 10 percent. if there were 6 million km2 of sea ice in the year 2000, how much would remain in 2020? group of answer choices are a. 7.85 b.4.86 c. 6.80 d. 3.67
You are driving your 1700 kg car at 18 m/s down a hill with a 5.0∘ slope when a deer suddenly jumps out onto the roadway. You slam on your brakes, skidding to a stop.
How far do you skid before stopping if the kinetic friction force between your tires and the road is 1.5×10^4 N?Solve this problem using conservation of energy.
Express your answer to two significant figures and include the appropriate units.
The distance the car skids before coming to a stop when driving down a hill with a slope of 5.0° at 18 m/s using conservation of energy is 19.84 meters.
What is conservation of energy?Conservation of energy is the principle that the total energy of an isolated system cannot change. The energy can only be transformed from one form to another. The law of conservation of energy, also known as the first law of thermodynamics.
To determine how far you skid before stopping using conservation of energy, follow these steps:
Step 1: Calculate the initial kinetic energy of the car: [tex]KE_{initial} = (1/2) * 1700 kg * (18 m/s)^2 = 275400 J[/tex]
Step 2: Calculate the gravitational potential energy gained by the car [tex](PE_{gravity})[/tex]: firstly, to find h we need to express it in terms of the distance. h = distance * sin(angle)
So, [tex]PE_{gravity} = 1700 kg * 9.81 m/s^2 * distance * sin(5.0^\circ)[/tex]
Step 3: Calculate the work done by friction [tex](W_{friction})[/tex]: [tex]W_{friction} = 1.5 * 10^4 N * distance[/tex]
Step 4: Apply conservation of energy: [tex]KE_{initial} + PE_{gravity} = W_{friction}[/tex], we get:
[tex]275400 J + (1700 kg * 9.81 m/s^2 * distance * sin(5.0^\circ)) = 1.5 * 10^4 N * distance[/tex]
Step 5: Solve for distance
[tex]distance * (1.5 * 10^4 N - 1700 kg * 9.81 m/s^2 * sin(5.0^\circ)) = 275400 J[/tex]
[tex]distance = 275400 J / (1.5 * 10^4 N - 1700 kg * 9.81 m/s^2 * sin(5.0^\circ))[/tex]
Using a calculator, the distance is approximately 19.84 meters. So, you skid about 19.84 meters before stopping.
To know more about conservation of energy , refer here
https://brainly.com/question/2137260#
#SPJ11
#4: A friend is wearing a pair of mirrored sunglasses whose convex surface has a focal length of (-20.0)cm. If your face is 40.0 cm from the sunglasses, how far behind the sunglasses is your image?
The image distance is negative, this means the image is formed behind the mirror, at a distance of 13.33 cm behind the sunglasses.
Since the sunglasses have a convex surface, we can use the mirror equation:
1/f = 1/do + 1/di
where f is the focal length of the mirror, do is the object distance (the distance between the object and the mirror), and di is the image distance (the distance between the mirror and the image).
In this case, f = -20.0 cm (since the mirror is convex), do = 40.0 cm (since your face is 40.0 cm from the sunglasses), and we want to find di.
Substituting these values into the mirror equation, we get:
1/(-20.0 cm) = 1/(40.0 cm) + 1/di
Simplifying this equation, we get:
-0.05 = 0.025 + 1/di
Subtracting 0.025 from both sides, we get:
-0.075 = 1/di
Dividing both sides by -0.075, we get:
di = -13.33 cm.
Learn more about convex here:
https://brainly.com/question/30557617
#SPJ1
a 0.686 meter long wire has a cross sectional area of 8.23 * 10 ( to power -6 ) meter² and a resistance of 0.125 at 20°C this wire could be made of:
1) aluminium
2) copper
3) tungsten
4) nichrome
Answer: 4) nichrome
Explanation:
I did the math
The wire could be made of copper. Therefore, option 2 is correct.
Use the formula for resistance:
R = (ρ × L) / A
where:
R is the resistance of the wire,
ρ is the resistivity of the material,
L is the length of the wire, and
A is the cross-sectional area of the wire.
Calculate the resistivity for each material using the given information and then compare it with the given resistance value.
Aluminum:
Resistance of the wire (R) = 0.125 Ω
Length of the wire (L) = 0.686 m
The cross-sectional area of the wire (A) = 8.23 × [tex]10^{-6}[/tex] m²
R = (ρ × L) / A
ρ = (R A) / L
= (0.125 × 8.23 × 10⁻⁶) / 0.686
Calculating ρ for aluminum:
ρ = 1.5 × 10⁻⁸ Ω.m
Copper:
ρ = 1.7 × 10⁻⁸Ω.m
Tungsten:
ρ = 5.6 × 10⁻⁸ Ω.m
Nichrome:
ρ = 1.10× 10⁻⁶ Ω.m
Compare the resistivity values with the known resistivity values for different materials:
Aluminum: ρ = 1.5 × 10⁻⁸ Ω.m
Copper: ρ = 1.7 × 10⁻⁸ Ω.m
Tungsten: ρ = 5.6 × 10⁻⁸ Ω.m
Nichrome: ρ = 1.10 × 10⁻⁶ Ω.m
Therefore, the wire could be made of copper.
To learn more about the copper, follow the link:
https://brainly.com/question/29137939
#SPJ2
do people weigh less near the equator because of the centrifugal force of the earth spinning? does the centrifugal force counteract gravity enough for even a marginal weight difference near the equator?
People do weigh less near the equator because of the centrifugal force of the earth spinning. Yes, The centrifugal force counteracts gravity enough for even a marginal weight difference near the equator.
This is because the equator is further away from the center of the earth than the poles.
As a result, people at the equator are moving faster than those at the poles due to the earth's rotation. This movement generates centrifugal force, which reduces the gravitational force acting on a person at the equator by about 0.3%.
Therefore, a person weighs about 0.5% less at the equator than at the poles.
For more such questions on centrifugal force, click on:
https://brainly.com/question/954979
#SPJ11
green light of wavelength 540 nm is incident on two slits that are separated by 0.50 mm. (a) make a list of physical quantities you can determine using this information and determine three of them. (b) describe three changes in the experiment that will each result in doubling the distance between the 0th and the first bright spot on the screen. explain.
Green light of wavelength 540 nm is incident on two slits that are separated by 0.50 mm can be determined various steps.
How can we describe Green light of wavelength?(a) Physical quantities that can be determined using this information include:
Wavelength of the light (given as 540 nm)Distance between the slits (given as 0.50 mm)Distance from the slits to the screen (not given, but assumed to be known)Three physical quantities that can be determined using this information are:
The spacing between bright fringes on the screenThe angle of diffraction of the lightThe location of the central bright fringe on the screen(b)
Three changes that will each result in doubling the distance between the 0th and the first bright spot on the screen are:
Doubling the distance between the slits and the screen: The distance between the slits and the screen affects the spacing between bright fringes on the screen.
By doubling the distance between the slits and the screen, the spacing between bright fringes will be doubled.
Halving the distance between the slits: The distance between the slits affects the angle of diffraction of the light.
By halving the distance between the slits, the angle of diffraction will be doubled, resulting in the doubling of the distance between the 0th and the first bright spot on the screen.
Using light of half the wavelength: The wavelength of the light affects the spacing between bright fringes on the screen.
By using light of half the wavelength (i.e., 270 nm), the spacing between bright fringes will be halved, resulting in the doubling of the distance between the 0th and the first bright spot on the screen.
Learn more about Green light
brainly.com/question/1159962
#SPJ11
a sketch of the system depicting all the forces on the car is drawn and labeled. which coordinate axis (highlighted in red) is the best choice to use for this problem?
The forces that acts on a moving car are majorly driving force, reactionary force, frictional force, gravitational force, and the air resistance.
A multiple set of forces acts on ant object, when it is in motion, lets see each of them clearly.
Driving force: This is the force generated by the car's engine that propels the car forward.
Friction force: This force acts opposite to the car's direction of motion and is caused by the interaction between the car's tires and the road surface.
Air resistance/drag force: This is the force that opposes the car's motion as it moves through the air.
Gravitational force: This force pulls the car down towards the Earth.
Centripetal force: This force acts on the car when it moves in a circular path, and is directed towards the center of the circle.
Normal force: This force is exerted on the car by the ground, perpendicular to the surface of the road.
Therefore, these mentioned forces interact in complex ways to determine the car's motion, and can be influenced by factors such as the car's speed, mass, and shape, as well as the road surface and external conditions like wind and temperature.
Learn more about force :
https://brainly.com/question/30761082
#SPJ4
The complete question is :
Draw the labelled sketch of a system of forces acting on a moving car and explain it.
a coin is placed at different locations on a vinyl disk which spins about the center at a constant angular velocity. the coin rotates without sliding on the disk. its linear velocity increases in magnitude when the distance from the location of the coin to the center of the disk increases. group of answer choices true false
False. The linear velocity of the coin remains constant because the angular velocity of the disk is constant and the coin rotates without sliding.
The distance from the location of the coin to the center of the disk does not affect the linear velocity of the coin.
The linear velocity of the coin is equal to the product of the angular velocity of the disk and the distance from the center of the disk to the location of the coin.
However, since the angular velocity of the disk is constant, the linear velocity of the coin is also constant, regardless of its distance from the center.
This can be explained by the fact that all points on the rotating disk undergo the same angular displacement in the same amount of time, which results in a constant angular velocity.
As a result, the linear velocity of the coin does not increase in magnitude as its distance from the center of the disk increases.
To learn more about velocity here:
https://brainly.com/question/17127206
#SPJ11
the magnitude of the total work done during the cycle is 1900 j and the change in internal energy from 1 ! 2 ! 3 is 1500.3 j. a) determine the heat, the work done on the gas, and u for a complete cycle. make sure to have the correct signs. b) how many active modes does each gas particle have? c) what is the heat for subprocess 3 ! 1?
a) Heat = 1900 J, Work done on the gas = 399.7 J, ΔU = 1500.3 Jb) Each monatomic gas particle has 3 active modes. c) Heat for subprocess 3 to 1 = -399.7 J
a) The heat and work done on the gas during a cycle Internal energy is a state function, which implies that the changes in the internal energy of a system are independent of how the energy is transferred. The net heat added to a system is equal to the difference between the work done by the system and the change in the internal energy of the system. Thus, the formula for the first law of thermodynamics is as follows: Q - W = ΔUwhere Q is the heat, W is the work done on the gas, and ΔU is the change in internal energy. Substituting the values given, we have1900 - W = 1500.3Therefore, W = 399.7 J Heat can be calculated as follows: Q = ΔU + W = 1500.3 + 399.7 = 1900 Jb) Number of active modes in each gas particleEach gas particle has three degrees of freedom: translational, rotational, and vibrational. For a monatomic gas, the gas particles only have translational degrees of freedom since they cannot rotate or vibrate. Thus, each monatomic gas particle has three active modes. c) Heat for subprocess 3 to 1The heat for subprocess 3 to 1 can be calculated using the first law of thermodynamics: Q = ΔU + W For this subprocess, ΔU = 1500.3 J and W = -1900 J (since the gas is expanding and doing work on the surroundings).Thus,Q = 1500.3 - 1900 = -399.7 J
Learn more about monatomic here:
https://brainly.com/question/16337385
#SPJ11
Please Help! Thanks
Study the scenario.
A rock falls off the edge of a cliff. The system consists of the rock, the cliff, and the Earth.
Which choice best describes the changes in kinetic and potential energy?
Responses:
Before the rock falls, all the energy is stored as potential energy. The potential energy remains the same because the Earth’s pull on the rock does not change. The kinetic energy remains the same because the acceleration remains constant. The total energy remains constant.
Before the rock falls, all the energy is stored as potential energy. The kinetic energy increases as the rock falls because its speed increases. The potential energy decreases as the rock falls because its position relative to the ground decreases. The total energy remains constant.
Before the rock falls, all the energy is stored as kinetic energy. As the rock falls, the kinetic energy remains constant because the rock’s acceleration remains constant. The potential energy decreases as the rock falls because its position relative to the ground decreases. The total energy decreases.
Before the rock falls, all the energy is stored as potential energy. The kinetic energy increases as the rock falls because its speed increases. The potential energy increases as the rock falls because its position relative to the ground increases. The total energy increases.
The falling of the rock will follow the principle of conservation of energy.
Energy conservation principleBefore the rock falls, all the energy is stored as potential energy. The kinetic energy increases as the rock falls because its speed increases. The potential energy decreases as the rock falls because its position relative to the ground decreases.
Thus, the total energy remains constant.
When the rock falls, it gains kinetic energy due to its motion, and loses potential energy due to its decrease in height. However, the total energy of the system (rock, cliff, and Earth) remains constant because energy is conserved. This is known as the conservation of energy principle.
More on energy conservation principles can be found here: https://brainly.com/question/30703463
#SPJ1
which of the following statements about the terrestrial planets is false? group of answer choices earth's atmosphere plays a central role in keeping our planet from freezing cold temperatures. venus is the hottest planet in our solar system, mainly due to an elevated greenhouse effect. long ago, mars probably had a thicker atmosphere than it does now, with sufficiently high temperatures and pressures to allow liquid water to exist on its surface. earth's atmosphere allows the sun's infrared radiation in but doesn't allow much visible light to escape, resulting in the greenhouse effect. despite being the closest planet to the sun, some parts of mercury have a surface temperature far below the freezing point of water.
The statement which is false about the terrestrial planets is : "despite being the closest planet to the sun, some parts of mercury have a surface temperature far below the freezing point of water."
Mercury is the closest planet to the Sun, which means that it receives a large amount of solar radiation. However, the planet's lack of atmosphere and slow rotation result in extreme temperature variations between its day and night sides. During its daytime, temperatures can reach up to 430 °C (800 °F), which is hot enough to melt lead.
However, as Mercury rotates away from the sun and enters its nighttime, its surface cools rapidly. Due to the lack of an atmosphere to hold in heat, the planet's nighttime temperatures can drop to as low as -173 °C (-280 °F). These extreme temperature variations make it difficult for any potential life to survive on Mercury.
Despite these extreme temperature variations, some parts of Mercury do not get cold enough to freeze water. Water freezes at 0 °C (32 °F), and the lowest temperature ever recorded on Mercury was around -183 °C (-297 °F). Therefore, while some parts of Mercury can get very cold, it never gets cold enough to freeze water is the correct option.
For more such questions on terrestrial planets, click on:
https://brainly.com/question/3406478
#SPJ11
how far into the future can the pan-star telescopes detect killer asteroid collisions with earth?
The Pan-STARRS telescopes can detect potential killer asteroids colliding with Earth up to a few weeks in advance.
The Panoramic Survey Telescope and Rapid Response System (Pan-STARRS) is a system of telescopes used for wide-field astronomical surveys, including asteroid detection. The system is capable of detecting near-Earth asteroids (NEAs) and potentially hazardous asteroids (PHAs) with diameters larger than 140 meters up to several decades in advance of their potential impact with Earth.
The exact time frame for detection depends on the size, trajectory, and reflectivity of the asteroid, as well as the observation frequency of the telescope system. However, the Pan-STARRS system provides an important tool for identifying potentially hazardous asteroids and informing future efforts for mitigation and prevention of catastrophic asteroid impacts.
To know more about telescope, here
brainly.com/question/17300587
#SPJ4
A boy holds a toy soldier in front of a concave mirror. The focal length of the mirror is 0.45m and the boy holds the toy soldier at a distance of 0.25m from the mirror. Find the image distance.
The image distance when a boy holds a toy soldier in front of a concave mirror, with a focal length of 0.45 m. is -0.56 m.
What is image distance?When an object is put in front of a plane mirror, this is the distance between the image that results and the focus.
To calculate the image distance, we use the formula below.
Formula:
1/f = 1/u+1/v Equation 1
Where:
f = Focal length of the mirror
v = Image distance
u = object distance
From the question,
Given:
f = 0.45 m
u = 0.25 m
Equation 1 can be changed to reflect these numbers to determine the image distance.
1/0.45 = 1/0.25 + 1/v
2.22 = 4+1/v
1/v = 2.22-4
1/v = -1.78
v = 1/(-1.78)
v = -0.56 m
To know more about image distance visit:-
https://brainly.com/question/27106646
#SPJ1
your friend, a graduate student in astronomy, is giving you a special tour of the local observatory. you notice that you are viewing the image from the big telescope from underneath the primary mirror; the beam of light has come through a small hole in the main mirror to an eyepiece below. this telescope uses what focusing arrangement?
The telescope uses a reflecting design with a concave primary mirror and a secondary mirror.
The telescope you are noticing utilizes a reflecting telescope, which shines light utilizing a sunken essential mirror situated at the lower part of the telescope. The light emission enters the telescope through a little opening in the essential mirror, which mirrors the light to an optional mirror situated close to the highest point of the telescope.
The optional mirror then, at that point, mirrors the light to an eyepiece situated along the edge of the telescope, which permits the spectator to see the picture shaped by the essential mirror. This kind of telescope is known as a Newtonian reflector, named after Sir Isaac Newton who imagined this plan in the seventeenth 100 years.
Reflecting telescopes enjoy upper hands over refracting telescopes, for example, being liberated from chromatic abnormality, and the capacity to create bigger gaps without a similar degree of cost and intricacy.
To learn more about reflecting, refracting and telescope, refer:
https://brainly.com/question/12575436
#SPJ4
what is an example of matter? a. oxygen gas b. energy c. heat d. light e. none of the answers are correct.
Oxygen gas is an example of matter because it has mass and occupies space. The correct option is A.
Matter can exist in various forms such as solids, liquids, gases, and plasma, and can be composed of atoms or molecules. The properties of matter, such as its density, temperature, and pressure, can be studied through the use of various physical and chemical processes.
Matter is composed of tiny particles called atoms, which consist of a nucleus containing positively charged protons and uncharged neutrons, surrounded by negatively charged electrons. The arrangement of these particles in matter determines its physical and chemical properties. These interactions play a critical role in many physical phenomena, including the behavior of materials under different conditions, the formation and evolution of stars and galaxies, and the behavior of subatomic particles.
To learn more about Matter visit here:
brainly.com/question/28487167
#SPJ4
a shotputter can exert 68 lb of force on a 0.55-slug shot. if she directs this force at 40o to the horizontal, what is the magnitude of its horizontal acceleration?
The magnitude of the horizontal acceleration of the shot put is 1.614 [tex]ft/s^2[/tex].
To find the size of the level speed increase of the shot put, we want to utilize Newton's Subsequent Regulation, which expresses that the power applied on an article is equivalent to the item's mass times its speed increase. For this situation, the mass of the shot put is given as 0.55 slugs, and the power applied by the shot putter is 68 lb.
To decide the level part of the power, we want to utilize geometry since the power is applied at a point of 40 degrees to the flat. The level part of the power is given by Fcos(40), where F is the all out power of 68 lb. Hence, the flat part of the power is 68cos(40) = 51.96 lb.
Presently we can utilize Newton's Second Regulation to track down the size of the level speed increase. Since the power is in pounds and the mass is in slugs, we really want to change over the power into slugs. Utilizing the transformation factor 1 lb = 1/32.2 slugs, we have:
51.96 lb * (1/32.2 slugs/lb) = 1.614 slugs-[tex]ft/s^2[/tex]
In this manner, the size of the level speed increase of the shot put is 1.614[tex]ft/s^2[/tex].
To learn more about horizontal acceleration, refer:
https://brainly.com/question/18997308
#SPJ4
Determine the resistance of a aluminum wire, if the resistance of the cone obtained after cutting it into ten equal parts and stacking them is found to be 1 ohm
Answer:
The resistance of the original aluminum wire is 1/100 ohm.
Explanation:
A wire's resistance is proportional to its length and inversely proportional to its cross-sectional area. When a wire is cut into ten equal segments and stacked, its length is decreased by one-tenth yet its cross-sectional area stays constant.
Let R denote the original aluminium wire's resistance.
When the wire is cut into ten equal sections and stacked, the resistance of each component is ten times that of the original wire (since the length is one-tenth and the cross-sectional area stays constant). As a result, the resistance of one portion is 10R.
The resistance of the whole cone is 1 ohm when all 10 pieces are stacked. As a result, one portion has a resistance of 1/10 ohm.
Equating the resistance of one part to 10R, we get:
10R = 1/10 ohm
Solving for R, we get:
R = 1/100 ohm
Therefore, the resistance of the original aluminum wire is 1/100 ohm.
To know more about resistance of wire:
https://brainly.com/question/12283329?referrer=searchResults
A hot, 100-g glass prism is placed in an insulated 300-mL sample of water at room temperature (22°C), causing the temperature of the water to come to equilibrium at 25°C. What was the initial temperature of the hot glass prism? [The specific heat of glass, cp,g, is 664 J/(kg °C).]
The initial temperature of the hot glass prism was 81.2°C.
What is glass prism?A transparent object having two triangular ends and three rectangular sides is known as glass prism.
As we know, Q = mcΔT
Q is heat transferred, m is the of the water, c is specific heat capacity of water, ΔT is change in temperature of the water.
Assuming no heat is lost to the surroundings, heat lost by hot glass prism is equal to heat gained by the water:
Q_lost = Q_gained
Heat lost by the hot glass prism can be calculated as: Q_lost = mcΔT
m is mass of the glass prism and ΔT is difference between initial temperature of prism (T_i) and final temperature of the water (25°C).
Heat gained by the water can be calculated as: Q_gained = mcΔT
m is mass of the water and c is specific heat capacity of water.
mcΔT = mcΔT_g
T_i = (ΔT_g / ΔT) x 25°C
Heat transferred from the glass prism to water is: Q = mcΔT = 100 g x 0.664 J/(g °C) x (25°C - T_i)
ΔT_g = T_i - T_hot = - (25°C - T_i)
100 g x 0.664 J/(g °C) x (25°C - T_i) = 300 g x 4.184 J/(g °C) x (25°C - 22°C)
T_i = 81.2°C
Therefore, initial temperature of the hot glass prism was 81.2°C.
To know more about glass prism, refer
https://brainly.com/question/3891897
#SPJ1
unpolarized light passes through polarizer at 60 degrees from vertical, what is the intensity of the light?
When unpolarized light passes through a polarizer at 60 degrees from the vertical, the intensity of the light is halved.
Unpolarized light, which consists of light waves vibrating in all planes perpendicular to the direction of propagation, does not have a specific direction of oscillation. This means that its electric field is randomly polarized in all directions perpendicular to the direction of motion. Polarization refers to the direction in which the electric field is oscillating.
Polarized light waves have an electric field that is oscillating in only one direction, whereas unpolarized light has an electric field that is oscillating in all directions perpendicular to the direction of motion. A polarizer is a filter that polarizes light waves by allowing only those waves that are oscillating in a particular direction to pass through. If unpolarized light passes through a polarizer at a 60-degree angle to the vertical, only half of its intensity will be able to pass through.
To learn more about Unpolarized light :
https://brainly.com/question/30739829
#SPJ11
what would be the advantage of making parallax measurements from pluto rather than from earth? would there be a disadvantage?
Answer:
Explanation:
Making parallax measurements from Pluto would offer several advantages over Earth:
Advantages:
Greater baseline: The distance between Earth and Pluto is much greater than the distance between two points on Earth. This means that the baseline for measuring parallax is much longer, which leads to greater accuracy.Different perspective: Observing parallax from Pluto would provide a different perspective on the universe than observing it from Earth. This could lead to new discoveries and a better understanding of the cosmos.Better measurements of nearby stars: When observing from Earth, stars appear to shift less due to parallax. Observing from Pluto would lead to greater shifts in nearby stars, allowing for more precise measurements of their distances.However, there are also some disadvantages to making parallax measurements from Pluto.Disadvantages:
Difficulty in observing: Observing parallax from Pluto would be much more difficult than observing it from Earth. Pluto is much smaller and has a lower surface gravity, which could make it harder to stabilize instruments.Limited observation time: The distance between Pluto and Earth varies widely, and there are only specific times when it is possible to observe parallax from Pluto. This could limit the amount of time available for making measurements.Transmission time: Data transmitted from Pluto would take several hours or even days to reach Earth, making real-time adjustments and measurements impossible.The advantage of making parallax measurements from Pluto is that it provides a much larger baseline for the measurements, which would increase the accuracy of the measurements. However, the disadvantage is that Pluto's orbit is highly elliptical, which could make the measurements more difficult and less precise.
Parallax is a method used by astronomers to measure distances to nearby stars. It involves measuring the apparent shift in position of a star relative to distant background stars as the Earth orbits around the Sun. This shift is caused by the observer's change in position relative to the star. By measuring the angle of this shift, astronomers can calculate the distance to the star.
If parallax measurements were made from Pluto, the distance between the observer and the star would be much greater than if the measurements were made from Earth. This larger baseline would result in a greater angle of shift, which would increase the accuracy of the measurements.
However, Pluto's highly elliptical orbit could make the measurements more challenging because the distance between Pluto and the star would change over time. This would require careful timing of the measurements to ensure accuracy. Additionally, Pluto's distance from Earth could make it more difficult to transmit the data back to Earth.
To know more about parallax measurements, refer here:
https://brainly.com/question/3836636#
#SPJ11
a weather balloon filled with he gas has a volume of 2.00x 103 m3 at ground level, where the atmospheric pressure is 1.000 atm and the temperature is 27 oc. after the balloon rises high above earth to a point where the atmospheric pressure is 0.340 atm, its volume increases to 5.00x103 m3. what is the temperature of the atmosphere at this higher altitude?
When the balloon rises high above earth to a point where the atmospheric pressure is 0.340 atm and its volume increases to 5.00 x 10³ m³, the temperature of the atmosphere at this higher altitude is approximately 255.1 K.
Using the combined gas law, we can determine the temperature at the higher altitude. The combined gas law is:
(P₁ × V₁) / T₁ = (P₂ × V₂) / T₂
Given:
P₁ = 1.000 atm (ground level pressure)
V₁ = 2.00 x 10³ m³ (ground level volume)
T₁ = 27°C + 273.15 (convert to Kelvin) = 300.15 K (ground level temperature)
P₂ = 0.340 atm (higher altitude pressure)
V₂ = 5.00 x 10³ m³ (higher altitude volume)
We want to find T₂, the higher altitude temperature:
(1.000 atm × 2.00 x 10³ m³) / 300.15 K = (0.340 atm × 5.00 x 10³ m³) / T₂
Solving for T₂:
T₂ = (0.340 atm × 5.00 x 10³ m³) × 300.15 K / (1.000 atm × 2.00 x 10³ m³)
T₂ ≈ 255.1 K
So, the temperature of the atmosphere at the higher altitude is approximately 255.1 K.
Learn more about combined gas law here: https://brainly.com/question/16019591
#SPJ11
a child pushes a merry-go-round from rest to a final angular speed of 0.50 rev/s with constant angular acceleration. in doing so, the child pushes the merry go-round 2.0 revolutions. what is the angular acceleration of the merry-go-round?
The angular acceleration of the merry-go-round is 4 rad/s².
To find the angular acceleration of the merry-go-round, follow these steps:
1. Convert the final angular speed from rev/s to rad/s:
Final angular speed = 0.50 rev/s * 2π rad/rev = π rad/s
2. Convert the number of revolutions to radians:
Number of revolutions = 2.0 rev * 2π rad/rev = 4π rad
3. Use the angular displacement equation to find the angular acceleration:
θ = ω₀ * t + 0.5 * α * t^2, where θ is angular displacement, ω₀ is initial angular speed (0 in this case), α is angular acceleration, and t is time.
4. Use the final angular speed equation to find time:
ω = ω₀ + α * t, where ω is final angular speed, ω₀ is initial angular speed (0 in this case), α is angular acceleration, and t is time.
5. Rearrange the final angular speed equation to find time in terms of angular acceleration:
t = (ω - ω₀) / α = π / α
6. Substitute the time expression into the angular displacement equation:
4π = 0.5 * α * (π / α)^2
7. Solve for angular acceleration:
α = 4 rad/s²
Hence, the angular acceleration of the merry-go-round is 4 rad/s².
To know more about angular acceleration, refer here:
https://brainly.com/question/30238727#
#SPJ11
the devices used by mechanical cooling thermostats to turn off early enough to prevent system overshoot or temperatures below the thermostat set point are called
The devices used by mechanical cooling thermostats to turn off early enough to prevent system overshoot or temperatures below the thermostat set point are called anticipators.
An anticipator is a small resistor that operates like a little heater inside your thermostat. The anticipator is the device that controls the duration of each heating cycle in old-style thermostats. This component essentially informs the heating and cooling system to cut off early. The mechanical thermostat anticipator is made up of two parts: the thermostat switch and the heat anticipator. When the thermostat switch turns off, the anticipator's heater stays on for a short period longer, avoiding overheating or undercooling of the controlled space.
learn more about thermostats here:
https://brainly.com/question/22598217
#SPJ4
every particle attracts every other particle in the universe with a gravitational force directly proportional to the mass of the objects. therefore, if the mass of the objects increase then the gravitational force will ?
If the mass of the objects increases, then the gravitational force between them will also increase, as it is directly proportional to the mass of the objects involved.
The law of universal gravitation is a physical law that describes the attraction between two masses. It states that every particle in the universe attracts every other particle with a force that is directly proportional to the product of their masses and inversely proportional to the square of the distance between them.
The equation for this law is F = G(m1m2/d²), where F is the force of attraction, G is the gravitational constant, m1 and m2 are the masses of the two objects, and d is the distance between them. As the masses of the objects increase, the gravitational force between them also increases, assuming that the distance between them remains constant.
Learn more about gravitational force here:
https://brainly.com/question/24783651
#SPJ11