a 1,200a feeder is tapped (over 10ft but less than 25 ft long)to supply a 225a main breaker panelboard having a 180a continuous load. what's the minimum size thhn copper feeder tap conductor that can be used?

The modulus of elasticity, also known as Young's modulus, is a measure of a material's stiffness or resistance to deformation under stress. It represents the ability of a material to resist elastic deformation when subjected to external forces.

The modulus of elasticity is calculated by dividing the applied stress by the resulting strain, and its units are usually expressed in terms of force per unit area (such as pounds per square inch or pascals).

Steel has a high modulus of elasticity, typically around 30 million psi or 200 GPa, which makes it very stiff and strong under tension. Concrete has a lower modulus of elasticity, typically around 3 to 5 million psi or 20 to 35 GPa, which makes it more flexible but less strong than steel. Wood also has a relatively low modulus of elasticity, typically around 1 to 2 million psi or 7 to 14 GPa, which makes it less stiff than steel or concrete but still quite strong for its weight.

To learn more about Young's modulus refer to:

brainly.com/question/13257353

#SPJ4

The Low-Level Wind Shear Alert System (LLWAS) provides wind data and software processes to detect the presence of hazardous wind shear.

LLWAS (Low-level windshear alerting systems) is a tool with a system to detect the presence of windshears close to the airport, and will provide warning windshear information automatically if has exceeded its threshold.

It works by collecting data from wind speed and direction sensors located around an airport to provide real-time monitoring of changes in wind direction and speed that can lead to hazardous wind shear events. The data is used to create an alert if hazardous wind shear is detected.

Learn more about LLWAS : https://brainly.com/question/30001468

#SPJ11

The solvent drainage and waste system operates without venting piping by using a combination of air flow and pressure.

Instead of relying on venting piping to exhaust fumes and waste, the system takes in air from the atmosphere and circulates it through the system with a blower or compressor. This creates a pressure difference that drives the solvent out of the system, taking any remaining waste with it. The pressure also keeps odors from escaping and prevents the system from backflowing.

Drainage is the removal of a mass of water either naturally or artificially from the surface or subsurface from a place.

Learn more about drainage : https://brainly.com/question/831589

#SPJ11

Force in all its members have increased

The vector product of mass (m) and acceleration (a) expresses the quantity of force (a). The force equation or formula can be expressed mathematically as follows:

F = ma In which case,

m = mass a = velocity

It is expressed in Newtons (N) or kilogrammes per second.

The acceleration an is provided by

a = v/t

Where

v = acceleration

t = time spent

As a result, Force can be expressed as follows:

F = mv/t

The formula for inertia is p = mv, which can also be expressed as Momentum.

As a result, force can be defined as the rate of change of momentum.

dp/dt = F = p/t

Force formulas are useful for determining the force, mass, acceleration, momentum, and velocity in any given problem.

To know more about Force,click on the link :

https://brainly.com/question/13191643

#SPJ1

The student question is: Service conductors passing over a roof shall be securely supported by substantial structures, and for a grounded system, where the substantial structure is ___, it shall be bonded by means of a bonding jumper and listed connector to the grounded overhead service conductor.

The answer to the blank is "metallic". So, for a grounded system, where the substantial structure is metallic, it shall be bonded by means of a bonding jumper and listed connector to the grounded overhead service conductor. This ensures that the metallic structure is safely connected to the grounding system, reducing the risk of electrical shock or damage.

To learn more about connected conductors : https://brainly.com/question/31274491

#SPJ11

A DC electric motor develops a power of 60 kW and a torque of 39 kgf.m. To calculate the speed of the motor in rpm, we can use the following formula:

Power (P) = Torque (T) × Angular Speed (ω)

First, we need to convert the torque from kgf.m to N.m (Newton-meters). 1 kgf is equal to 9.81 N, so the torque in N.m is:

T = 39 kgf.m × 9.81 N/kgf = 382.59 N.m

Next, we need to convert the power from kW to W (Watts). 1 kW is equal to 1000 W, so the power in W is:

P = 60 kW × 1000 W/kW = 60000 W

Now we can rearrange the formula to find the angular speed (ω):

ω = P / T = 60000 W / 382.59 N.m = 156.82 rad/s

Finally, we need to convert the angular speed from rad/s to rpm (revolutions per minute). Since there are 2π radians in one revolution and 60 seconds in a minute, we can use the following conversion:

RPM = ω × (60 s/min) / (2π rad/rev) = 156.82 rad/s × (60 s/min) / (2π rad/rev) = 1498.62 rpm

Therefore, the speed of the motor is approximately 1499 rpm.

for more question on Angular Speed

https://brainly.com/question/6860269

#SPJ11

Electricity is the movement of electrons between atoms.

The atomic mass or atomic weight is the total mass of an atom, including protons, neutrons, and electrons. Atomic mass units are used to measure atomic mass or weight. Electrons contribute only a small portion of the atomic structure's mass, but they play an important role in the chemical reactions that produce molecules. The atomic weight can be thought of as the number of protons plus the number of neutrons for most purposes. Because the number of neutrons in an atom can vary, most elements can have multiple atomic weights.The charges of protons and electrons are equal and opposite. Protons are positively charged, while electrons are negatively charged. Normally, atoms have an equal number of protons and neutrons.  

To know more about Atom, click on the link :

https://brainly.com/question/30898688

#SPJ1

The time constant of the system is not defined because the output signal remains at zero for all values of t. The sensitivity of the system is a = 0.

The time constant and sensitivity of a measurement system can be determined from the equation y = a (1 - e ^ -t/τ). Here, τ is the time constant and a is the sensitivity. The output signal is initially steady at 60 units and the input signal is then suddenly increased to 90 units.

The equation of the system is given by:

y = a (1 - e ^ -t/τ)

Given that the initial output signal is steady at 60 units, it implies that when t=0, y=60. Thus the equation becomes:

60 = a (1 - e ^ 0/τ)

60 = a (1 - 1)

60 = 0

This equation is not possible. It implies that the value of a is zero. Thus, the equation of the system is simplified to:

y = 0

Therefore, the answer  is a = 0.

Learn more about output signal : https://brainly.com/question/30953449

#SPJ11

Under constant flow circumstances, the experimental system can be described using lumped elements like resistance, voltage source, and load. The plastic tubing can be used to create an equivalent circuit.

When dealing with steady state flow, a number of assumptions must be made. Initially, the mass flow throughout the systems is constant. The fluid also keeps its composition constant. Finally, only heat and work are exchanged between the environment and the system.

For a steady state flow process to occur, the conditions must be constant throughout the entire apparatus as time passes. Over the time period of interest, there must not have been any increase of mass or energy. The same mass flow rate

To know more about voltage  visit:-

https://brainly.com/question/31160586

#SPJ1

Technology governance guides how frequently technical systems are updated and how technical updates are approved and funded. Option C is correct.

Technology governance is the framework, policies, and procedures that regulate how an organization's IT infrastructure is managed and monitored. This involves defining how the company's technology-related activities are managed, including decision-making authority, accountability, and access to technology resources.

Technology governance entails establishing IT policies and procedures, providing training and guidance to employees on IT policies and procedures, defining the duties and responsibilities of IT personnel, ensuring regulatory compliance with technology-related laws, and defining how technical systems are updated and authorized for funding.

Technology governance guides how frequently technical systems are updated, and how technical updates are approved and funded.

For instance, it establishes the policies and procedures governing technical change management, risk management, and the decision-making process for technical projects. Technology governance also provides guidance on how to manage the technical resources that are deployed in the organization.

Therefore Option C is correct. Governance guides the technical system.

To learn more about Technology governance :

https://brainly.com/question/14364696

#SPJ11

Answer:

its B. ima keep it short its B

Explanation

The "recovery" stage is the time during annealing when there is little change in ductility and yield strength but usually a significant change in electrical conductivity and corrosion resistance.

The metal is heated to a certain temperature during the annealing process so that recrystallization can take place. Any flaws brought on by the metal's deformation are now fixed. After maintaining that temperature for a predetermined amount of time, the metal is cooled to room temperature.

The physical and occasionally chemical qualities of a material are altered during the annealing process, which increases ductility and decreases hardness to make a material more workable.

To know more about annealing process visit:-

https://brainly.com/question/29699923

#SPJ1

The transfer function is a mathematical representation of the relationship between the input and the output of a system. The steady-state error, or ess, is the difference between the desired output and the actual output when the system reaches a steady state. The natural frequency is the frequency of the system's response without any external forces.

Transfer Function: Transfer Function is used in signal processing, control engineering, and other disciplines that deal with systems or signals. The ratio of output to input in Laplace transform is known as the transfer function.

Steady-State Error: The error that happens when the system is at a stable state is referred to as a steady-state error. The difference between the desired and actual response is known as steady-state error. A system's ability to track a specific input as time progresses is characterized by this kind of error. If the input signal is a unit step, then the steady-state error is referred to as the static error coefficient. The coefficient of the steady-state error is frequently used to classify systems in control engineering.

Natural Frequency: Natural frequency is a term used in physics to describe how quickly an object vibrates when it is set in motion. The number of oscillations made by a system in a given time period without any external force acting on it is referred to as its natural frequency. A natural frequency is a measure of a system's stiffness and mass. In a control system, it is the frequency at which the system oscillates in the absence of any input.

A natural frequency is also known as an undamped natural frequency or a resonance frequency, and it is represented by the symbol [tex]\omega_n[/tex].You can assume the following in the problem. If you have any specific values, kindly provide them.

Learn more about Transfer Function here:

https://brainly.com/question/24241688

#SPJ11

The plant will need to perform 9,100,000 processing and assembly procedures altogether.

Shape operations, property-enhancing operations, and surface processing operations are the three distinct categories of processing operations. By using mechanical force, heat, or other forms and combinations of energy, shaping operations change the work material's geometry.

There are 250 components in each product.

Parts purchased as a percentage equal 65%.

250 - (65% x 250) = 87.5 is the number of components that will be produced in the new facility.

Eight processing steps are needed to manufacture each component.

The new factory's processing procedures per component totaled 8 x 87.5, or 700.

13 x 1000 x (700 + 1) = 9,100,000 is the total number of processing and assembly procedures needed for the 13 different models.

To know more about assembly visit:-

https://brainly.com/question/13557244

#SPJ1

Sealer should be sprayed over an original OEM finish before clearcoating. (Option B)

A sealer is a type of primer that is specifically designed to provide a smooth and uniform surface for the clearcoat to adhere to. It also helps to prevent any bleeding or discoloration from the original finish, and can improve the overall appearance of the final finish.

While primers and adhesion promoters can also be used in automotive painting, a sealer is the most appropriate product to use over an original OEM finish before clearcoating. Epoxy, on the other hand, is typically used as a primer for bare metal surfaces, rather than over an existing finish.

Learn more about OEM at:

https://brainly.com/question/17422536

#SPJ1

The type of sprinkler system that allows immediate and simultaneous discharge of all sprinkler heads is the deluge system.

In a deluge system, all the sprinkler heads are open and ready to discharge water at all times. The system is activated by a separate fire detection system, such as smoke detectors or heat sensors, which triggers the release of water from all the sprinkler heads at once. This makes deluge systems ideal for high hazard areas where fire can spread quickly, such as chemical storage areas or power plants.

In contrast, wet-pipe systems have water in the pipes at all times and require heat to open individual sprinkler heads, while dry-pipe and pre-action systems use compressed air or other gases to hold water back until a sprinkler head is triggered.

To learn more about sprinkler system refer to:

brainly.com/question/28992367

#SPJ4

Land surveying is the era used to gather records additionally a part of geomatics. but geomatics is a technology to discover ways to analysis that survey geospatial facts through diverse approach and making out a selection via it.

Land Surveying (or Engineering Surveying) is in truth a sub-area of Geomatics. however, in practice, there may be little to no distinction between the disciplines and the phrases get used interchangeably often.
A Geomatics engineer will employ sensors, knowledge and software to provide notably correct positional information for any of these scenarios.
Surveyors make specific measurements to decide belongings boundaries. They provide information applicable to the form and contour of the Earth's floor for engineering, mapmaking, and creation initiatives.

To know more about land surveying click on right here
brainly.com/question/29841451
#SPJ4

I. Normal Stress in Each Section:

- Aluminum: σ = (P × L) / (A × E) = (100 × 0.5) / (1 × 7.3 x 10^10) = 6.85 MPa
- Copper: σ = (P × L) / (A × E) = (100 × 0.2) / (0.25 × 1.7 x 10^11) = 8.82 MPa
- Steel: σ = (P × L) / (A × E) = (100 × 0.3) / (0.5 × 2 x 10^11) = 3 MPa

II. Displacement of B with Respect to C:
ΔBC = (P × L^3) / (E × A) = (100 × 0.2^3) / (2 x 10^11 × 0.5) = 0.002 mm
III. Displacement of A with Respect to D:
ΔAD = (P × L^3) / (E × A) = (100 × 0.5^3) / (7.3 x 10^10 × 1) = 0.009 mm

Given data: The composite shaft consists of aluminum, copper, and steel sections. The cross-sectional area and modulus of elasticity in the figure are given. Neglect the size of the collars at b and c. Determine the following: i. The normal stress in each section ii. The displacement of b with respect to ciii.

The displacement of end a with respect to end d The given shaft is subjected to loading as shown in the figure, which is a simple case of compound stress where the stress is induced due to the combined effect of the normal stress σ and shear stress τ.σ is a longitudinal stress acting along the axis of the shaft.

You can read more about normal stress at https://brainly.com/question/17135312

#SPJ11

a) The ideal gas equation of state and the ideal gas law is utilized to calculate the volume flow rate of air at the inlet, which is 2.73 cubic meters per second. b)  The first law of thermodynamics is employed to determine how pressure, temperature, and volume change and the determined internal energy is 108,000 J.

a) The volume flow rate of air at the inlet can be determined using the ideal gas law and the ideal gas equation of state. The equation is PV = nRT, where P is the pressure, V is the volume, n is the number of moles, R is the gas constant, and T is the temperature. Using the given values, we can determine the volume flow rate (V) to be 2.73 cubic meters per second.

b) The change in pressure, temperature, and volume can be determined using the first law of thermodynamics. The equation is ΔU = Q - W, where ΔU is the change in internal energy, Q is the heat transferred, and W is the work done. Using the given values, we can determine the change in internal energy (ΔU) to be 108,000 J.

You can learn more about the ideal gas equation at: brainly.com/question/28837405

#SPJ11

Answer:

Test-driven development is a great idea for software development projects, as it helps ensure that the code is properly tested and written correctly. The benefit of this approach is that it allows for more accurate debugging and testing, resulting in fewer errors in the final product. The drawback is that it can be time consuming and expensive to implement, and may require additional resources to ensure that all tests are done properly.

a) Program B has the better guarantee on the running time, for large values of N (N>10,000).

b) Program A has the better guarantee on the running time, for small values of N (N<100)

.c) Which program will run faster on average for N=1,000 cannot be determined from the given information.

d) It is possible that program B will run faster than program A on all possible inputs.Explanation:

a) For large values of N (N>10,000), Program B has a worst-case running time of N log N which is better than the running time of program A which is 150N log N. Hence, program B has the better guarantee on the running time.

b) For small values of N (N<100), Program A has a worst-case running time of 150N log N which is better than the running time of program B which is N. Hence, program A has the better guarantee on the running time.

c) The average running time of the programs for N=1000 cannot be determined from the given information.

d) It is possible that program B will run faster than program A on all possible inputs. It depends on the input, so it is not possible to make a general statement regarding which program is faster on all possible inputs.

You can read more about program at https://brainly.com/question/23275071

#SPJ11

The most commonly installed type of fire sprinkler system is the wet-pipe system. In a wet-pipe system, the pipes are filled with water and are pressurized so that when the heat of a fire activates the sprinkler head, water is released onto the fire.

Pre-action systems use a separate water line to fill the pipes with water and need to be triggered by another type of detector such as smoke or heat, while dry-pipe systems have pressurized air or nitrogen in the pipes and the water is released when the heat of a fire activates the sprinkler head. Deluge systems are used when large amounts of water need to be released quickly, such as when a large area needs to be flooded quickly.

In order to install a wet-pipe system, the pipes must be connected to a water source and the sprinkler heads must be placed at the correct height in the room. Once the system is installed, it must be tested regularly to make sure that it is functioning properly. It is also important to remember that water damage can be caused by a malfunctioning system, so it is important to regularly check and maintain the system.

for more such questions on fire sprinkler system.

https://brainly.com/question/7652753

#SPJ11

The filter paper is placed flat on the bottom of the Hirsch funnel and wetted before collecting crystals to ensure effective filtration and prevent loss of the collected crystals.

The wetting of the filter paper helps to create a seal between the paper and the funnel, which prevents the crystals from bypassing the filter paper and being lost. The wetting of the paper also helps to eliminate air pockets or gaps that could lead to uneven filtration or channeling, which can also result in loss of the crystals. In addition, the filter paper should fit flat on the bottom of the Hirsch funnel to ensure even distribution of the crystals and to prevent them from accumulating in one area, which could also result in loss of the crystals.

Learn more about Hirsch funnel: https://brainly.com/question/30648758

#SPJ11

Technician A and Technician B both are correct as brake fluid that is allowed to remain uncovered does absorb water and brake fluid can damage the paint on a vehicle's fender if it is accidentally spilled.

Technician A is correct because brake fluid is hygroscopic, which means it absorbs moisture from the atmosphere. This water can corrode brake parts and lead to failure, as well as increase the fluid's boiling point, leading to brake fade and reduced stopping power.
Technician B is also correct because brake fluid is made up of corrosive materials that can break down paint and other surfaces. If the brake fluid is not cleaned off the fender immediately, it can cause permanent damage to the paint.

You can learn more about corrosive materials at: brainly.com/question/29632416

#SPJ11

You are required to leave an empty lane between your car and the emergency vehicle if it is safe, otherwise reduce speed by 20 mph is true.

A four-lane highway is a high-speed, controlled-access road with two lanes in each direction. It is often called a divided highway because of the median strip that separates the two directions of traffic. It is the most common type of multi-lane highway in the United States.

This is known as the "Move Over" law, which requires drivers to move over one lane away from any emergency vehicle with flashing lights if it is safe to do so. If it is not safe to move over, drivers are required to slow down to a speed that is at least 20 mph less than the posted speed limit. This law is in effect in many states to protect emergency responders and provide a safer working environment for them.

To learn more about speed-limit:

https://brainly.com/question/28488266

#SPJ11

Option B. In the 21st century, teaching is more complex because teachers have students with a wider variety of learning needs.

According to Dewey, curriculum and institutions should be secondary to children in brain-based pedagogy since learning is socially produced. Students have to apply prior knowledge to generate new meaning in order to effectively learn.

This is what makes individualized instruction complex.Individualized instruction has been emphasized since Dewey's times. However, in the 21st century, teaching is more complex because teachers have students with a wider variety of learning needs. Student-centered learning, on the other hand, has been a popular idea in education for years.

The popularity of student-centered learning can be traced back to John Dewey, a prominent educational philosopher. In Dewey's view, student-centered learning focused on the student's experience, interests, and interaction with the environment. Therefore the correct option is B.

Learn more about "teachers" at: https://brainly.com/question/28328532

#SPJ11

The strategies to meet the indoor air-quality credit requirements reflect the management category knowledge domain of indoor air quality.

Indoor air-quality management includes several strategies that can be used to meet credit requirements. The following are some of the strategies that can be used to improve indoor air quality in buildings:

To sum it up, the strategies to meet the indoor air-quality credit requirements reflect the management category knowledge domain of indoor air quality.

To learn more about air-quality:

https://brainly.com/question/1211889

#SPJ11

The minimum thickness of copper metallization recommended for a circuit board is 1 mil. This thickness can be adjusted according to the design requirements, but increasing the thickness of the copper metallization may result in increased costs.

The amount of copper metallization deposited on a circuit board is determined by the application and design requirements of the board. Generally, the minimum thickness recommended for copper metallization is 1 mil (0.001 inches). This ensures a reliable electrical connection for the board and helps protect against shorts and corrosion. To provide an additional layer of protection, the thickness of the copper can be increased as needed.

For your process engineer, the recommended minimum thickness of copper metallization should be 1 mil. This is a general guideline that can be adjusted based on the design requirements of the circuit board. However, it is important to note that increasing the thickness of the copper metallization may result in increased costs due to the additional material needed.

You can learn more about copper metal at: brainly.com/question/1488623

#SPJ11

The owner of a building designed by registered engineers and architects may not be able to recover damages from snow and ice if the engineers and architects had specified the use of materials or building techniques that are not designed to handle those types of conditions.

Additionally, the owner may not have taken proper preventative measures to ensure the building was properly insulated and protected from the weather, or the owner may not have maintained the building appropriately. Finally, the owner may not have been able to prove negligence on the part of the engineers or architects in the building's design or construction.

In conclusion, the owner of a building designed by registered engineers and architects may not be able to recover damages from snow and ice if the building was not designed to withstand such conditions, if the owner failed to take proper preventative measures to protect the building, or if the owner could not prove negligence on the part of the engineers and architects.

You can learn more about building design at: brainly.com/question/8741590

#SPJ11