Based on the statement made by the student, The student's statement that the puck slid a bigger distance before stopping when it was moving faster is correct.
What is the distance about?The above is because the kinetic energy of an object in motion is proportional to its mass and the square of its velocity. When an object is moving faster, it has more kinetic energy, and it takes more work to stop it. In the case of the puck, the frictional force acting on it was not strong enough to overcome the kinetic energy of the puck when it was moving faster, resulting in a longer sliding distance before it came to a stop.
However, the student's conclusion that they should hit their brakes twice as far from a stop sign when driving at 40 mph instead of 20 mph to stop their car in time is not necessarily accurate. While it is true that a car moving at a higher speed has more kinetic energy and requires more work to stop, the distance required to stop the car depends on several factors, such as the mass of the car, the efficiency of the brakes, and the condition of the road surface.
Read more about distance here:
https://brainly.com/question/26550516
#SPJ1
a battery with an emf of 25.10 v delivers a constant current of 2.50 ma to an appliance. how much work (in j) does the battery do in two minutes?
A battery with an emf of 25.10 v provides an appliance with a constant current of 2.50 ma, the work done by the battery in two minutes is 7.53 J.
The power P in watts can be calculated using the formula given below.P = V x Iwhere V is the voltage, and I is the current. In this scenario, V = 25.10 V and I = 2.50 mA = 2.50 x 10⁻³A = 0.0025A. Therefore, P = 25.10 V x 0.0025A = 0.06275 W.
The work W in joules (J) done by the battery in two minutes can be calculated using the formula given below.W = P x t where t is the time in seconds. In two minutes, the time t is 2 x 60 = 120 seconds.Therefore, W = 0.06275 W x 120 s = 7.53 J.
Learn more about work done here:
https://brainly.com/question/13662169
#SPJ11
(i) the asteroid icarus, though only a few hundred meters across, orbits the sun like the planets. its period is 410 d. what is its mean distance from the sun?
The mean distance of the asteroid Icarus from the Sun is approximately 1.24 astronomical units.
The mean distance of the asteroid Icarus from the Sun can be determined using Kepler's Third Law of Planetary Motion. This law states that the square of the orbital period (T) is proportional to the cube of the semi-major axis (a) of the orbit. Mathematically, it can be written as:
T² ∝ a³
We can use the Earth's orbit as a reference, which has a period of 365.25 days and a semi-major axis of 1 astronomical unit (AU).
Using the given period of Icarus (410 days), we can set up the following proportion:
(410² / 365.25²) = (a³ / 1³)
Calculating the left side of the equation gives:
(168100 / 133483.0625) = a³
Taking the cube root of both sides, we get:
a ≈ 1.24 AU
So, the mean distance of the asteroid Icarus from the Sun is approximately 1.24 astronomical units.
Know more about Earth's orbit here:
https://brainly.com/question/31074247
#SPJ11
Select the correct answer. Which statement best explains the relationship between the electric force between two charged objects and the distance between them?
A. As the distance increases by a factor, the electric force increases by the square of that factor.
B. As the distance increases by a factor, the electric force increases by twice that factor.
C. As the distance increases by a factor, the electric force decreases by twice that factor.
D. As the distance increases by a factor, the electric force decreases by the same factor.
E. As the distance increases by a factor, the electric force decreases by the square of that factor.
Answer:
E
"As the distance increases by a factor, the electric force decreases by the square of that factor" best explains the relationship between the electric force between two charged objects and the distance between them.
The force exerted on the charged particles is inversely proportional to the square of the distance between them. The further they are the less the force the closer they are the more the force.
The correct answer between all the choices given is the last choice or letter E.
which kind of disturbance is created by moving a spring toy up and down?responsesin a circular motionin a circular motion,in the same direction as the wave motionin the same direction as the wave motion,parallel to the wave motionparallel to the wave motion,perpendicular to the wave motion
Moving a spring toy up and down creates a disturbance that is parallel to the wave motion. This type of disturbance is called a longitudinal wave.
In a longitudinal wave, the particles of the medium oscillate parallel to the direction of the wave motion. When you move a spring toy up and down, you create a series of compressions and rarefactions in the spring, where the coils are compressed together and then spread apart.
This creates a longitudinal wave that travels through the spring. Sound waves are also examples of longitudinal waves, where the compression and rarefaction of air particles create the wave motion.
To know more about disturbance
https://brainly.com/question/26994019
#SPJ4
Why give it is necessary to have exhibition sometimes give two point
In general, exhibitions are a cheap way to advertise a business, build brand recognition, and interact with potential clients and partners.
What justifies the need for exhibitions?These are two justifications for why exhibitions are essential:
Improved Visibility: Businesses may promote their goods, services, and brands to a sizable audience by participating in exhibitions. Increased brand knowledge and recognition could ultimately result in more revenue and earnings thanks to this visibility.
Possibilities for networking: Exhibitions give companies a place to meet and interact with prospective clients, business partners, and suppliers. These contacts may result in new business connections and chances, which eventually may help an organization develop and succeed.
To learn more about exhibitions visit:
brainly.com/question/19689448
#SPJ9
what does newton's universal law of gravitation explain? (select all the apply) explains why an apple falls at a constant rate explains the origin of mass explains the motion of the moon and other planets explains or implies kepler's laws
Newton's universal law of gravitation explains the motion of the moon and other planets, and implies Kepler's laws. It does not explain why an apple falls at a constant rate or the origin of mass.
Newton's Universal Law of Gravitation is a fundamental principle in physics that describes the force of attraction between two objects with mass. The law states that every object in the universe attracts every other object with a force that is directly proportional to the product of their masses and inversely proportional.
In mathematical terms, the equation is written as F = G * ((m1 * m2) / r²), where F is the force of attraction, and G is the gravitational constant. This law explains a wide range of phenomena, from the motion of planets and stars to the behavior of falling objects on Earth. It is essential to our understanding of the universe and forms the basis for many important concepts in modern physics, including Einstein's theory of general relativity.
To know more about Newton's universal law visit here:
brainly.com/question/3159150
#SPJ4
to stretch a spring a distance of 0.3 m from the equilibrium position, 120 j of work is done. what is the value of the spring constant k?
It takes 120 j of effort to extend a spring 0.3 m from its equilibrium state. The value of the spring constant k is 2666.67 N/m.
The work done to stretch a spring is given by the formula:
W = 0.5 × k × x^2
where W is the work done, k is the spring constant, and x is the distance the spring is stretched from its equilibrium position.
In this problem, we know that the work done is 120 J and the distance the spring is stretched is 0.3 m. Substituting these values into the formula, we get:
120 = 0.5 × k × 0.3^2
Simplifying the equation, we get:
k = 120 / (0.5 × 0.3^2)
k = 2666.67 N/m
To learn more about spring constant
https://brainly.com/question/20388857
#SPJ4
How long would it take an object traveling 12 m/s to go 60 m? Round to the nearest whole number.
Answer: It would take 5 seconds for an object traveling at 12 m/s to go 60 m. Rounded to the nearest whole number, the answer is 5 seconds.
Explanation:
To find the time it would take an object to travel a certain distance at a given speed, we can use the formula:
time = distance / speed
Plugging in the given values, we get:
time = 60 m / 12 m/s
time = 5 seconds
what is the magnitude of the average emf induced in the loop of wire as it moves from location a to location b?
The magnitude of the average emf induced in the loop of wire as it moves from location a to location b depends on the strength of the magnetic field, the dimensions of the loop, and the angle at which it moves through the field.
To determine the magnitude of the average emf induced in the loop of wire as it moves from location a to location b, we need to use Faraday's law of electromagnetic induction, which states that the magnitude of the emf induced in a circuit is proportional to the rate of change of the magnetic flux through the circuit.
In this case, the loop of wire is moving through a magnetic field that is perpendicular to the plane of the loop. As the loop moves from location a to location b, the area of the loop that is in the magnetic field changes, causing the magnetic flux through the loop to change.
The magnitude of the average emf induced in the loop during this motion can be calculated as:
emf = ΔΦ/Δt
where ΔΦ is the change in magnetic flux and Δt is the time interval over which the change occurs.
The change in magnetic flux can be calculated as:
ΔΦ = B × ΔA
where B is the magnitude of the magnetic field, and ΔA is the change in the area of the loop that is in the magnetic field.
The time interval over which the change in magnetic flux occurs is equal to the time it takes for the loop to move from location a to location b.
Therefore, the magnitude of the average emf induced in the loop can be expressed as:
emf = B × ΔA/Δt
To calculate the change in the area of the loop, we need to know the dimensions of the loop and the angle at which it is moving through the magnetic field. Assuming that the loop is rectangular and has sides of length L and W and that it moves through the magnetic field at an angle θ, the change in the area can be expressed as:
ΔA = WL × sin(θ)
Substituting this expression into the equation for emf, we get:
emf = B × WL × sin(θ)/Δt
To learn more about magnetic fields
https://brainly.com/question/11514007
#SPJ4
the wavelength of an electromagnetic wave is measured to be 600 m.(a)what is the frequency of the wave?(b)what type of em wave is it?
Answer:
Radio wave :
The wavelength of an electromagnetic wave is measured to be 600 m.
Explanation:
All remain are given in attachment!
The vector 1/root2i+1/root2j
is a
The supplied vector can be categorised as a 2-dimensional unit vector because it is in the x-y plane's first quadrant and has equal components in the i and j directions.
Vector formula: What is it?The equation to determine a vector's magnitude in two dimensions is |v| =(x2 + y2). (x, y). The Pythagorean theorem is the foundation of this formula. The equation to determine a vector's magnitude (in three dimensions) is |V| = (x2 + y2 + z2). (x, y, z).
What is the position vector's formula?The position vector from A to B can be calculated using the formula AB = (xk+1 - xk, yk+1 - yk). Referring to a vector, the position vector AB is a vector that begins at A and ends at B.
To know more about vector visit:-
https://brainly.com/question/31289115
#SPJ1
two point charges having charge values of 4.0 x 10-6 c and -8.0 x10-6 c, respectively, are separated by 2.4 x 10-2 m. what is the value of the mutual force between them?
The value of the mutual force between them is -3.0 x 10^-3 N.
The mutual force between two point charges can be calculated using Coulomb's law, which states that the force between two charges is directly proportional to the product of their charges and inversely proportional to the square of the distance between them. The equation for Coulomb's law is F = k * (q1 * q2) / r^2, where F is the force, k is Coulomb's constant, q1 and q2 are the charges, and r is the distance between the charges.
Plugging in the given values, we get:
F = (9.0 x 10^9 N*m^2/C^2) * [(4.0 x 10^-6 C) * (-8.0 x 10^-6 C)] / (2.4 x 10^-2 m)^2
Simplifying the expression, we get:
F = -3.0 x 10^-3 N
Note that the negative sign indicates that the force is attractive, since the charges have opposite signs.
To know more about charges, here
brainly.com/question/17101884
#SPJ4
a constant force is applied to an object, causing the object to accelerate at 5.00 m/s2 . what will the acceleration be if
if a constant force is applied to an object, causing the object to accelerate at 5.00 m/s2, the acceleration will remain at 5.00 m/s2 unless there is a change in the force applied or the object's mass.
This is due to Newton's Second Law of Motion, which states that the force applied to an object is directly proportional to its acceleration, while its mass is inversely proportional.
In other words, if the force applied remains constant, the acceleration will remain constant as well, regardless of the object's mass. If the force applied changes, the acceleration will change proportionally, with a larger force resulting in a greater acceleration and a smaller force resulting in a smaller acceleration.
Therefore, the answer to the question of what the acceleration will be if a constant force is applied to an object causing it to accelerate at 5.00 m/s2 is that it will remain at 5.00 m/s2 unless there is a change in the force applied or the object's mass.
Learn more about Newton's Second Law of Motion here:
https://brainly.com/question/13447525
#SPJ11
Ratan pushes having a same weight Through the same distance across a room
Tuesday will require more effort from Ratan since the dry surface will make it difficult to overcome the force of friction between the box and the surface through the same distance.
Why is walking on a wet surface more challenging than one that is dry?The smoothness or roughness of the surfaces affects frictional force. Force decreases with a smooth surface or increases with a rough surface, respectively. Friction is significantly lower on smooth and wet surfaces compared to dry or rough ones.
Does friction increase on a dry surface?Because of the increase in surface roughness, making the surface dry or rubbery increases friction. It is more difficult to reduce friction on rough surfaces than on smooth ones, hence lubricants like water or oil are sometimes utilized.
To learn more about friction visit:
brainly.com/question/13000653
#SPJ1
If Ratan pushes two objects with the same weight through the same distance across a room, the amount of work done by Ratan on each object would be the same. This is because the amount of work done is determined by both the force applied and the distance traveled.
If the weight and distance are the same for both objects, then the work done will be equal. However, if the surfaces are different, the amount of friction will vary and Ratan will have to apply different amounts of force to move each object the same distance.
This means that the force exerted by Ratan on each object is equal, and the work done in moving both objects is also the same since work is calculated as force multiplied by distance.
For more questions on: distance
https://brainly.com/question/26550516
#SPJ11
what equation is used to calculate elastic potential energy? ln activity 2-2, what will you need to do in order to allow the software to calculate the correct value of elastic potential energy?
The equation used to calculate elastic potential energy is:
Elastic potential energy = 1/2 * k * x^2
Elastic potential energy is the energy stored in an object when it is stretched or compressed. It is dependent on the spring constant and the displacement of the object from its equilibrium position. The equation to calculate elastic potential energy is 1/2 * k * x^2, where k is the spring constant and x is the displacement from the equilibrium position. To calculate the elastic potential energy using software, you need to input the values of k and x into the equation, and the software will calculate the value.
To know more about Elastic potential energy, here
brainly.com/question/12807194
#SPJ4
Fill in the blank
The highest frequency ______ waves are microwaves
Answer:
The highest frequency electromagnetic waves are microwaves.
Hope This Helps!
If an object is moving at 5m/s north and an balanced force is acting on it, it will continue to move at that same velocity.
Answer:An object having balanced forces definitely cannot be accelerating.
Which of the following best represents
a coil spring in an off-road truck with a spring constant k of 87.6 kn/m (87,600 n/m) is compressed a distance of 9.2 cm (0.092 m) from its original unstretched position. what is the increase in potential energy of the spring?
The increase in the potential energy of the spring is 360.44J.
The energy that a body possesses due to its location in relation to other objects, internal pressures, electric charge, and other reasons is called potential energy. The following formula determines the potential energy held in a spring that has been compressed or stretched:
PE = (1/2)kx²
where,
x = the distance the spring has been compressed or extended from its equilibrium position
k = the spring constant
The spring constant in this instance is stated as k = 87,600 N/m, while the spring's compression distance is specified as x = 0.092 m. As a result, the spring's increased potential energy is:
PE = (1/2)kx²
= (1/2)87,600 × 0.092²
= 360.44 J
Therefore, the increase in the potential energy of the spring is 360.44J.
To learn more about potential energy, refer to:
https://brainly.com/question/13997830
#SPJ4
if 12.5 c of charge is transferred from the cloud to the ground in a lightning strike, what fraction of the stored energy is dissipated?
Answer:
The energy stored in a cloud due to separation of charges that causes a lightning strike can be estimated using the equation:
E = (1/2) * C * V^2
where E is the energy stored, C is the capacitance of the cloud, and V is the potential difference between the cloud and the ground.
Assuming that the capacitance of the cloud is 10 microfarads and the potential difference between the cloud and the ground is 100 million volts, the energy stored in the cloud is:
E = (1/2) * 10^-5 F * (10^8 V)^2 = 5*10^13 J
Now, if 12.5 coulombs of charge is transferred from the cloud to the ground, the energy dissipated can be calculated as:
W = V * Q = V * (12.5 C)
where W is the work done, Q is the charge transferred, and V is the potential difference between the cloud and the ground during the lightning strike.
Assuming that the potential difference remains constant at 100 million volts, the work done or energy dissipated is:
W = (10^8 V) * (12.5 C) = 1.25 * 10^10 J
Therefore, the fraction of stored energy dissipated is:
Fraction = (energy dissipated) / (energy stored)
Fraction = (1.25 * 10^10 J) / (5*10^13 J)
Fraction = 0.00025 or 0.025%
Thus, only a very small fraction of the energy stored in the cloud is dissipated during a lightning strike.
As per the given statement, if 12.5 C of charge is transferred from the cloud to the ground in a lightning strike, the fraction of the stored energy that is dissipated is (25/2 * V1²) * (Q1 - 6.25) / Q1².
We know that the energy stored in a charged capacitor can be calculated using the formula:E = (1/2) * C * V²Where,E is the energy storedC is the capacitance of the capacitorV is the potential difference between the plates of the capacitorLet E1 be the initial energy stored in the cloud before the lightning strike.And E2 be the energy stored in the cloud after the lightning strike.From the law of conservation of energy, we know that the total energy of a closed system remains constant. Therefore,E1 = E2 + EdWhere Ed is the energy dissipated during the lightning strike.Let the capacitance of the cloud be C.So, the initial energy stored in the cloud can be calculated as:E1 = (1/2) * C * V1²Similarly, the final energy stored in the cloud after the lightning strike can be calculated as:E2 = (1/2) * C * V2²And the energy dissipated can be calculated as:Ed = E1 - E2Therefore,Ed = (1/2) * C * (V1² - V2²)But we know that,Charge Q = C * VTherefore,The initial charge stored in the cloud can be calculated as:Q1 = C * V1And the final charge stored in the cloud can be calculated as:Q2 = C * V2Now, let's consider the given statement:"12.5 C of charge is transferred from the cloud to the ground in a lightning strike".So, the final charge stored in the cloud can be written as:Q2 = Q1 - 12.5We need to find the fraction of energy dissipated.Using the above expressions for Ed and Q2, we get:Ed = (1/2) * C * [(Q1/C)² - ((Q1 - 12.5)/C)²]Ed = (1/2C) * [Q1² - (Q1 - 12.5)²]Ed = (1/2C) * [(Q1² - Q1² + 25Q1 - 156.25)]Ed = (25/2C) * (Q1 - 6.25)Ed/Q1 = (25/2C) * (1 - 6.25/Q1)Now, the fraction of energy dissipated can be obtained by using the expression:Ed/E1 = Ed/(1/2 * C * V1²)= (25/2C) * (1 - 6.25/Q1) / (1/2 * C * V1²)= (25/2 * V1²) * (1 - 6.25/Q1) / Q1= (25/2 * V1²) * (Q1 - 6.25) / Q1²Hence, the fraction of energy dissipated is (25/2 * V1²) * (Q1 - 6.25) / Q1².
To know more about lightning strike click here:
brainly.com/question/15733465
#SPJ11
what is the main type of energy conversion taking place? responses mechanical energy is converted to thermal energy as the energy from movement creates heat in the surrounding air. mechanical energy is converted to thermal energy as the energy from movement creates heat in the surrounding air. thermal energy is converted to mechanical energy as the energy from heat provides energy for movement. thermal energy is converted to mechanical energy as the energy from heat provides energy for movement. chemical energy is converted to mechanical energy as the energy from digested food provides energy for movement. chemical energy is converted to mechanical energy as the energy from digested food provides energy for movement. mechanical energy is converted to chemical energy as the movement from movement creates reactions in the surrounding air
The main type of energy conversion taking place is chemical energy is converted to mechanical energy as the energy from digested food provides energy for movement. Option 3 is correct.
This is because the energy used for movement in living organisms comes from the breakdown of food molecules, such as glucose, through the process of cellular respiration. During cellular respiration, the chemical energy stored in food molecules is converted into a form of energy that can be used by cells to do work, which is called ATP (adenosine triphosphate). ATP is then used to power the mechanical work of muscles, which allows for movement.
Thermal energy is not involved in this process, as there is no mention of heat being a factor in the energy conversion. Mechanical energy is not converted to chemical energy, as this is not how living organisms obtain the energy needed for movement. Finally, there is no mention of reactions in the surrounding air. Option 3 is correct.
What is the main type of energy conversion taking place?
Responses
Mechanical energy is converted to thermal energy as the energy from movement creates heat in the surrounding air. Thermal energy is converted to mechanical energy as the energy from heat provides energy for movement. Chemical energy is converted to mechanical energy as the energy from digested food provides energy for movement. Mechanical energy is converted to chemical energy as the movement from movement creates reactions in the surrounding airTo know more about the Energy conversion, here
https://brainly.com/question/29299298
#SPJ4
(c) find the tangential speed of each particle. 4.00 kg particle 14.4 incorrect: your answer is incorrect. you may have used the mass of the object instead of its distance from the x axis. m/s 2.00 kg particle 7.2 correct: your answer is correct. m/s 3.00 kg particle 10.8 incorrect: your answer is incorrect. what is the equation relating the angular speed to the tangential speed? m/s
The following terms should be used in your answer: "tangential speed", "m/s 2.00 kg particle 7.2", and "angular speed".
The equation relating the angular speed to the tangential speed is given by:v = ωr where v is the tangential speed, ω is the angular speed, and r is the radius. To find the tangential speed of each particle, we need to know the angular speed and the radius of each particle. The given masses and distances from the x-axis are as follows:4.00 kg particle at 14.4 m from the x-axis 2.00 kg particle at 7.2 m from the x-axis3.00 kg particle at 10.8 m from the x-axisUsing the equation v = ωr, we can calculate the tangential speed for each particle as follows:4.00 kg particle:ω = 2π/8 = π/4 rad/sr = 14.4 tangential speed, v = ωr = (π/4) x 14.4 = 3.6π m/s2.00 kg particle:ω = 2π/4 = π/2 rad/sr = 7.2 tangential speed, v = ωr = (π/2) x 7.2 = 3.6π m/s3.00 kg particle:ω = 2π/6 = π/3 rad/sr = 10.8 tangential speed, v = ωr = (π/3) x 10.8 = 3.6π m/sTherefore, the tangential speed of the 4.00 kg particle is 3.6π m/s, the tangential speed of the 2.00 kg particle is 3.6π m/s, and the tangential speed of the 3.00 kg particle is 3.6π m/s.
learn more about tangential speed here:
https://brainly.com/question/14391529
#SPJ4
a 5-kg bag of groceries is tossed across the surface of a table at 4 m/s and slides to a stop in 3 s. what is the average force of friction acting on it?
Answer:
Force of friction = 3.33 N
Explanation:
The distance the bag slides can be calculated using the velocity and time
d = vt
d = 4m/s(3s)
d = 12 m
W = Fd and W = ∆KE=1/2mv^2
[tex]\frac{1}{2} mv^2=Fd\\\\F=\frac{mv^2}{2d}\\ \\F=\frac{(5kg)(4m/s)^2}{2(12m)} \\\\F=3.333 N[/tex]
The average force of friction acting on the 5-kg bag of groceries tossed across the surface of a table at 4 m/s and slides to a stop in 3 s is 16.7 N.
What is friction?
The resistance that a surface or object encounters when it comes into touch with another object or surface that has a different motion is known as friction. Friction happens when two objects slide against one another. Friction is the resistance that opposes motion. For instance, when a car accelerates, the friction between the road and the tires opposes the car's motion, and the car accelerates more slowly.
The following equation is used to compute the force of friction:
F_f = μF_n
Where F_f is the force of friction,
μ is the coefficient of friction,
and F_n is the normal force.
It's worth noting that the force of friction is proportional to the force holding two items together and the type of material on the surfaces in contact. The coefficient of friction is a measure of the force of friction between two objects. The unit of coefficient of friction is N (Newton).
How can you calculate the average force of friction?
We can use the formula, f = m x a to calculate the force of friction, where 'm' is the mass of the object and 'a' is the acceleration due to friction.
The formula can also be written as F_f = μF_n.
Given that the mass of the bag is 5-kg, the initial velocity of the bag is 4 m/s, and the time taken for the bag to come to a stop is 3s.
Then we can calculate the acceleration using the formula,
a = (v - u)/t, where 'v' is the final velocity, 'u' is the initial velocity and 't' is the time taken.
a = (0-4)/3 = -4/3 m/s^2.
We can now calculate the force of friction using the formula,
f = m x a. f = 5 kg x (-4/3 m/s^2) = -20/3 N.
However, the force of friction is negative since it acts in the opposite direction of the motion of the object.
Therefore, the average force of friction acting on the bag is 20/3 N or 6.67 N (rounded off to two decimal places).
The average force of friction acting on the 5-kg bag of groceries tossed across the surface of a table at 4 m/s and slides to a stop in 3 s is 16.7 N.
To know more about friction click here:
brainly.com/question/24186853
#SPJ11
The representative elements are those with unfilled energy levels in which the "last electron" was added to a p or d orbital. an f orbital. an s or p orbital.
The representative elements are those with unfilled energy levels in which the "last electron" was added to an s or p orbital. Therefore the correct option is option C.
The "last electron" in an atom refers to the outermost electron that is not part of a filled electron shell. This electron is also called the valence electron, and it is the electron that is most likely to participate in chemical reactions and bond formation with other atoms.
The properties of the valence electron largely determine the chemical behavior and reactivity of an element.
This includes elements in groups 1, 2, and 13-18 of the periodic table. The electrons in these elements occupy the outermost s and p orbitals, which are collectively known as the valence shell.
These valence electrons are responsible for the chemical properties of the elements and their reactivity. Therefore the correct option is option C.
For such more question on electron:
https://brainly.com/question/13380972
#SPJ11
a ray of light ( f = 5 * 10 to power -1 ) travelling in air strikes a block of sodium chloride at an angle of 30. what is the angle of refraction for the light ray in the sodium chloride?
1) 19
2) 25
3) 40
4) 49
Answer:
The correct answer is 1) 19.
photons and show the electron transit
Extra questions
26. The spectrum of sunlight has dark lines. These dark lines are due to the absorption of certain
wavelengths by the cooler gases in the atmosphere of the Sun.
a) One particular dark spectral line has a wavelength of 590 nm. Calculate the energy of a
photon with this wavelength.
b) The diagram shows some of the energy
levels of an isolated atom of helium.
i.
Explain the significance of the
energy levels having negative
values.
ii. Explain, with reference to the
energy level diagram shown, how
a dark line in the spectrum may
be due to the presence of helium
in the atmosphere of the Sun.
iii. All the light absorbed by the
atoms in the Sun's atmosphere is
re-emitted. Suggest why a dark
spectral line of wavelength 590
nm is still observed from the Earth.
Energy:10-¹ J
0
-1.6
-2.4
-3.0
-5.8
-7.6
The energy of a photon with a wavelength of 590 nm is [tex]3.36 * 10^-19[/tex]
How to find the energy of the photon?The energy of a photon can be calculated using the equation:
E = hc/λ
where E is the energy of the photon, h is Planck's constant [tex](6.626 * 10^-34 J.s)[/tex], c is the speed of light[tex](3.00 * 10^8 m/s)[/tex], and λ is the wavelength of the photon in meters.
To convert 590 nm (nanometers) to meters, we can use the conversion factor:
[tex]1 nm = 1 * 10^-9 m[/tex]
So, [tex]590 nm = 590 * 10^-9 m[/tex]
Plugging these values into the equation, we get:
E = [tex](6.626 * 10^-34 J.s * 3.00 * 10^8 m/s) / (590 * 10^-9 m)[/tex]
E = [tex]3.36 * 10^-19 J[/tex]
Therefore, the energy of a photon with a wavelength of 590 nm is [tex]3.36 * 10^-19[/tex]
Learn about wavelength here https://brainly.com/question/24452579
#SPJ1
a generator produces 33.0 v when turning at 860 rev/min. what emf does it produce when turning at 490 rev/min?
When turning at 490 RPM, the generator produces an EMF of 18.7 V.
When a generator produces 33.0 V while turning at 860 rev/min, the emf the generator produces when turning at 490 rev/min is 18.8 V.
The equation relating EMF with angular velocity is as follows:EMF=BAwN EMF = BAwN EMF = BAwN Where,B is the strength of the magnetic field A is the area of the coilw is the angular velocityN is the number of turns in the coil It can also be expressed as EMF = k × w EMF = k × w where k is the constant that depends on the strength of the magnetic field, the area of the coil, and the number of turns in the coil. Therefore, for the generator given, EMF = k × w EMF = k × wIt can be written asEMF1/EMF2=w1/w2 EMF1/EMF2 = w1/w2where EMF1 and w1 are the initial values and EMF2 and w2 are the final values. Substituting the given values, we getEMF1/EMF2=w1/w2 EMF1/EMF2 = w1/w218.8/33 = 490/8600.53333 = 0.56976EMF2 = EMF1/w1/w2 EMF2 = EMF1/w1/w2EMF2 = 33/(0.56976)EMF2 = 18.8Therefore, the emf the generator produces when turning at 490 rev/min is 18.8 V.
To know more about emf click here:
brainly.com/question/29672664
#SPJ11
Can anyone help me pls
The correct option is B: Longitudinal, because the waves travel away from the source, parallel to the movement of the source.
Sound waves are mechanical waves that require a medium to travel through, such as air, water, or solids. These waves are characterized by their frequency, wavelength, amplitude, and speed.
Sound waves are longitudinal waves because the particles of the medium vibrate in the same direction as the wave travels. In other words, the wave compresses and rarefies the medium in the same direction as the wave propagation. This means that the particles of the medium move parallel to the direction of the wave propagation.
Therefore, option B is the correct option as it correctly explains that sound waves are longitudinal and travel away from the source parallel to the movement of the source.
To know more about sound waves, visit:
https://brainly.com/question/21995826
#SPJ1
There is some ice at the beginning of the time interval, but all of the ice disappears before the end of the interval.
This statement suggests that the ice undergoes a phase change from solid to liquid, indicating heat transfer.
If 500 g of ice at -10°C is added to 1000 g of water at 50°C, how much ice melts and what is the final temperature of the mixture?All of the ice will melt, and the final temperature of the mixture will be 10°C.
What would happen if the surroundings were at a temperature lower than the ice during the time interval?If the surroundings were at a lower temperature than the ice, heat would flow from the ice to the surroundings, causing the ice to freeze instead of melt.
Learn more about heat transfer here:
https://brainly.com/question/31065010
#SPJ1
Ball a, of mass ma
, is connected to ball b, of mass mb
, by a massless rod of length L
. (Figure 1)The two vertical dashed lines in the figure, one through each ball, represent two different axes of rotation, axes a and b. These axes are parallel to each other and perpendicular to the rod. The moment of inertia of the two-mass system about axis a is Ia
, and the moment of inertia of the system about axis b is Ib
. It is observed that the ratio of Ia
to Ib
is equal to 3:
Ia/Ib=3
Assume that both balls are pointlike; that is, neither has any moment of inertia about its own center of mass.
1. Find the ratio of the masses of the two balls.
2. Find da, the distance from ball a to the system's center of mass
1. The ratio of the masses of the two balls is 3(x + L/2) / (x - L/2), and
2. da, the distance from ball a to the system's center of mass, is (2Lma) / (3(ma + mb)).
To solve this problem, we can use the parallel axis theorem, which states that the moment of inertia of a system about an axis parallel to an axis through the center of mass is given by:
I = Icm + Md^2
where Icm is the moment of inertia of the system about an axis through the center of mass, M is the total mass of the system, and d is the distance between the two axes.
To find the ratio of the masses of the two balls, we can set up a system of equations using the parallel axis theorem.
Let ma and mb be the masses of balls a and b, respectively, and let x be the distance from ball a to the center of mass of the system. Then we have:
Ia = Icm + ma(x - L/2)^2
Ib = Icm + mb(x + L/2)^2
We are given that Ia / Ib = 3, so we can substitute Ia = 3Ib into the above equations and simplify:
3Ib = Icm + ma(x - L/2)^2
Ib = Icm + mb(x + L/2)^2
Dividing the first equation by the second equation, we get:
3 = (ma / mb) * ((x - L/2)^2 / (x + L/2)^2)
Simplifying, we get:
3 = (ma / mb) * ((x - L/2) / (x + L/2))^2
Taking the square root of both sides and rearranging, we get:
ma / mb = 3 * (x + L/2) / (x - L/2)
To find da, the distance from ball a to the system's center of mass, we can use the fact that the center of mass is located at a point that balances the torques about both axes.
Let xm be the distance from ball b to the center of mass. Then we have:
ma(x - L/2) = mb(xm + L/2)
ma(x - L/2)^2 = mb(xm + L/2)^2
Solving for xm in terms of x, we get:
xm = (ma / mb)(x - L/2) - L/2
The center of mass is located at a point that balances the torques about both axes, so we also have:
Ia(x - da) = Ib(xm - da)
Substituting xm in terms of x, we get:
Ia(x - da) = Ib[(ma / mb)(x - L/2) - L/2 - da]
Simplifying, we get:
(x - da) / [(ma / mb)(x - L/2) - L/2 - da] = Ib / Ia
Substituting Ia / Ib = 3, we get:
(x - da) / [(ma / mb)(x - L/2) - L/2 - da] = 1/3
Cross-multiplying and simplifying, we get:
da = (2Lma) / (3(ma + mb))
Therefore, the ratio of the masses of the two balls is 3(x + L/2) / (x - L/2), and da, the distance from ball a to the system's center of mass, is (2Lma) / (3(ma + mb)).
For such more question on masses:
https://brainly.com/question/86444
#SPJ11