The mole fraction of C6H6 in the top product is 69.8% and the mole fraction of C7H8 in the top product is 30.2%.
Distillation tower is a separation technique for the purification of a liquid mixture or a solution based on the variations in the boiling point of the components of the mixture.
Let us solve the problem in the question.
The given information are as follows: Feed = 350 kg mole/h
C6H6+C7H8.40% (mole fraction) of C6H6 in the feed
The top product contains C6H6 = 97% (mole fraction)
Therefore, the bottom product contains C6H6 = 3% (mole fraction)
Operating pressure of distillation tower = 1 atm
Let x = moles of C6H6 in the top product(350)(0.4) = x + (moles of C6H6 in the bottom product) (this is because all the moles of C6H6 must be accounted for)
Thus, the moles of C6H6 in the bottom product = (350)(0.4) - x
Let y = moles of C7H8 in the top product
Therefore, the moles of C7H8 in the bottom product = (350 - x - y)
We know that the top product contains C6H6 = 97% (mole fraction)
Thus, x/(x + y) = 0.97 or x = 0.97x + 0.97y
The operating pressure of distillation tower is 1 atm and we know that the boiling point of C6H6 is lower than that of C7H8.
Hence, C6H6 will boil off first leaving behind the C7H8.
Therefore, all the moles of C6H6 will be in the top product.
Thus ,x + y = moles of C6H6 in the feed = 350(0.4) = 140
Therefore, 0.97x + 0.97y = 0.97(140) = 135.8 and
x + y = 140
Therefore, solving both equations gives the value of x and y as follows: x = 97.7y = 42.3
Hence, the top product contains 97.7 moles of C6H6 and 42.3 moles of C7H8.
Therefore, the mole fraction of C6H6 in the top product is given by x/(x + y) = 97.7/(97.7 + 42.3) = 0.698 or 69.8% (approximate to one decimal place)
Therefore, the mole fraction of C7H8 in the top product is given by y/(x + y) = 42.3/(97.7 + 42.3) = 0.302 or 30.2% (approximate to one decimal place)
Know more about mole fraction here:
https://brainly.com/question/30724931
#SPJ11
You are burning butane, C4H10 to CO2. You feed 100 mol/min C4H10 with stoichiometric oxygen. Your flue gas contains 360 mol/min of CO2. What is the extent of reaction, ? 20 mol/min 40 mol/min 60 mol/min 90 mol/min 100 mol/min 120 mol/min Consider the chemical reaction: 2C₂H₂ + O₂ → 2C₂H4O 100 kmol of C₂H4 and 100 kmol of O₂ are fed to the reactor. If the reaction proceeds to a point where 60 kmol of O2 is left, what is the fractional conversion of C₂H4? What is the fraction conversion of O₂? What is the extent of reaction? 0.4, 0.8, 40 kmol 0.4, 0.8, 60 kmol 0.8, 0.4, 40 kmol O 0.8, 0.4, 60 kmol
1. Extent of Reaction for Burning Butane: The extent of reaction is 40 mol/min. 2. Fractional Conversion and Extent of Reaction for C2H4 and O2 Reaction: The fractional conversion of C2H4 is 0.4, the fractional conversion of O2 is 0.8, and the extent of reaction is 40 kmol.
1. Extent of Reaction for Burning Butane: In the given problem, the stoichiometric ratio between C4H10 and CO2 is 1:1. Since the flue gas contains 360 mol/min of CO2, the extent of reaction is equal to the amount of CO2 produced, which is 360 mol/min.
2. Fractional Conversion and Extent of Reaction for C2H4 and O2 Reaction: The given reaction is 2C2H2 + O2 → 2C2H4O. Initially, 100 kmol of C2H4 and 100 kmol of O2 are fed to the reactor. If 60 kmol of O2 is left at the end, it means 40 kmol of O2 reacted. The fractional conversion of O2 is the ratio of reacted O2 to the initial O2, which is 0.4 (40 kmol/100 kmol).
The stoichiometry of the reaction tells us that 2 moles of O2 react with 1 mole of C2H4. Since the fractional conversion of O2 is 0.4, it means 0.4 moles of O2 reacted for every 1 mole of C2H4 reacted. Therefore, the fractional conversion of C2H4 is 0.4.
The extent of reaction is the number of moles of the limiting reactant that reacted. In this case, the extent of reaction is 40 kmol, as 40 kmol of O2 reacted.
Learn more about stoichiometric : brainly.com/question/6907332
#SPJ11
Geothermal sources produce hot water flows on pressure 60 psia
and temperature 300 oF.
If the installation of a power plant with CO2 gas
working fluid works with the following operating conditions:
-
The enthalpy change of the working fluid (CO2 gas) in the power plant, assuming an isentropic process, can be calculated by finding the difference in enthalpies between the geothermal source conditions and the power plant operating conditions.
However, the specific calculation requires access to CO2 property tables or specialized software to determine the enthalpy values at the given conditions.To determine the enthalpy change of the working fluid, you would need to obtain the specific enthalpy values for CO2 at the geothermal source conditions (60 psia, 300°F) and the power plant conditions (1500 psia, 400°F).
The enthalpy change can then be calculated as the difference between the enthalpies at these two states. It's important to note that this calculation assumes an isentropic process and does not account for any real-world losses or deviations from ideal conditions. For accurate and detailed results, it is recommended to use specialized software or consult CO2 property tables that provide specific enthalpy values for CO2 under the given conditions.
To know more about enthalphy visit:
https://brainly.com/question/14307149
#SPJ11
The gas phase reaction, N₂ + 3 H₂-2 NHs, is carried out isothermally. The Ne molar fraction in the feed is 0.1 for a mixture of nitrogen and hydrogen. Use: N₂ molar flow= 10 mols/s, P=10 Atm, and T-227 C. a) Which is the limiting reactant? b) Construct a complete stoichiometric table. c) What are the values of, CA, 8, and e? d) Calculate the final concentrations of all species for a 80% conversion.
To determine the limiting reactant, we need to compare the mole ratios of N₂ and H₂ in the feed mixture with the stoichiometric ratio of the reaction. The stoichiometric ratio of N₂ to H₂ is 1:3.
A)Given that the N₂ molar fraction in the feed is 0.1 and the N₂ molar flow rate is 10 mol/s, we can calculate the actual moles of N₂ in the feed:
Actual moles of N₂ = N₂ molar fraction * N₂ molar flow = 0.1 * 10 = 1 mol/s
Next, we need to calculate the actual moles of H₂ in the feed:
Actual moles of H₂ = (1 mol/s) * (3 mol H₂ / 1 mol N₂) = 3 mol/s
Since the actual moles of N₂ (1 mol/s) are less than the moles of H₂ (3 mol/s), N₂ is the limiting reactant.
b) A stoichiometric table can be constructed to show the initial moles, moles reacted, and final moles of each species:
Species | Initial Moles | Moles Reacted | Final Moles
--------------------------------------------------
N₂ | 1 mol | | 1 - x mol
H₂ | 3 mol | | 3 - 3x mol
NH₃ | 0 mol | | 2x mol
c) In the stoichiometric table, "x" represents the extent of reaction or the fraction of N₂ that has been converted to NH₃. At 80% conversion, x = 0.8.
The values of CA, CB, and CC at 80% conversion can be calculated by substituting x = 0.8 into the stoichiometric table:
CA (concentration of N₂) = (1 mol/s) - (1 mol/s * 0.8) = 0.2 mol/s
CB (concentration of H₂) = (3 mol/s) - (3 mol/s * 0.8) = 0.6 mol/s
CC (concentration of NH₃) = (2 mol/s * 0.8) = 1.6 mol/s
d) The final concentrations of all species at 80% conversion are:
[ N₂ ] = 0.2 mol/s
[ H₂ ] = 0.6 mol/s
[ NH₃ ] = 1.6 mol/s
These concentrations represent the amounts of each species present in the reaction mixture after 80% of the N₂ has been converted to NH₃.
know more about stoichiometric :brainly.com/question/24663542
#SPJ11
012 If the reaction of 30.0 mL of 0.55 M Na2CO3 (molar mass 105.99 g/mol) solution with 15.0 ml of 1.2 M CaC12 (111.0 g/mol) solution produced 0.955 g of CaCO3 (100.09 g/mol). Calculate the percentage yield of this reaction. A) 578% B) 92.7% C) 46.3% D) 53.0 016-Consider the reaction: MgO+2HC MgCl + H20, AH--243 kJ/mol. 0.42 g of Mg0 were added to a 20 mL of 0.5 M HCI solution at 24.2 °C. What is the final temperature reached after mixing? (Specific hest-4.07 1/gC, mass of MgCl, sol.-22.4 g) AYLAYC B) 50.85 C C) 37.5°C D) 26.65°C
The percentage yield of the reaction is approximately 61.6%. The final temperature reached after mixing is approximately 23.89°C.
To calculate the percentage yield, we need to compare the actual yield of the product to the theoretical yield of the product.
Volume of Na2CO3 solution = 30.0 mL
Molarity of Na2CO3 solution = 0.55 M
Volume of CaCl2 solution = 15.0 mL
Molarity of CaCl2 solution = 1.2 M
Mass of CaCO3 produced = 0.955 g
First, we need to calculate the number of moles of Na2CO3 and CaCl2 used in the reaction:
Na2CO3 moles are equal to (Na2CO3 solution volume) x (Na2CO3 solution molarity).
= (30.0 mL) * (0.55 mol/L)
= 16.5 mmol
Volume of the CaCl2 solution multiplied by its molarity equals the number of moles of CaCl2.
= (15.0 mL) * (1.2 mol/L)
= 18.0 mmol
The stoichiometric ratio of Na2CO3 to CaCO3 is 1:1, so the theoretical yield of CaCO3 can be calculated using the moles of Na2CO3:
Theoretical yield of CaCO3 = Moles of Na2CO3 * (Molar mass of CaCO3 / Molar mass of Na2CO3)
= 16.5 mmol * (100.09 g/mol / 105.99 g/mol)
= 15.6 mmol
= 1.55 g (approx.)
Now, we can calculate the percentage yield:
(Actual yield / Theoretical yield) / 100 equals the percentage yield.
= (0.955 g / 1.55 g) * 100
≈ 61.6%
Therefore, the percentage yield of this reaction is approximately 61.6%.
To calculate the final temperature, we can use the heat transfer equation:
q = mcΔT
Mass of MgO = 0.42 g
Volume of HCl solution = 20 mL
Molarity of HCl solution = 0.5 M
Specific heat = 4.07 J/g°C
Mass of MgCl2 solution = 22.4 g
Heat change (ΔH) = -243 kJ/mol (converted to J/mol)
First, we need to calculate the moles of MgO used in the reaction:
Moles of MgO are equal to (MgO mass) divided by (MgO molar mass).
= 0.42 g / 40.31 g/mol
≈ 0.0104 mol
The reaction is exothermic, so the heat released by the reaction can be calculated using the heat change (ΔH) and the moles of MgO:
Heat released = (Moles of MgO) * (ΔH)
= 0.0104 mol * (-243,000 J/mol)
= -2,527 J
Now we can calculate the heat transferred to the HCl solution:
q = mcΔT
-2,527 J = (20.42 g) * (4.07 J/g°C) * (ΔT)
ΔT ≈ -0.31°C
Since the initial temperature is 24.2°C, the final temperature reached after mixing is approximately:
Final temperature = Initial temperature + ΔT
= 24.2°C - 0.31°C
≈ 23.89°C
Therefore, the final temperature reached after mixing is approximately 23.89°C.
To know more about Temperature, visit
brainly.com/question/4735135
#SPJ11
5) CO3²- a. Is it polar b. what is the bond order
16) CH3OH
17) -OH 18) N2O
19) CO a. Is it polar
20) CN- a. is it polar
Lewis Structures Lab Draw the Lewis structures and answer any questions. You must localize formal charges and show all resonance structures.
CO₃²⁻ is non polar. Its bond order is 1.33.
Due to the presence of resonance and symmetry in the CO₃²⁻ molecule, it is an overall non-polar molecule. The geometry of carbonate ion is trigonal planar. Among the three oxygen atoms attached to the central carbon atom, the negative charge is evenly distributed.
Bond order of a molecule is defined as the number of bonds present between a pair of atoms. The total number of bonds present in a carbonate ion molecule is 4.
And the bond groups between the individual atoms is 3.
Therefore bond order is 4/3 = 1.33
To know more about CO₃²⁻ here
https://brainly.com/question/32796569
#SPJ4
Please discuss the meaning of 1E4 [Bq/t] which is a
maximum concentration of Cs-137 for the license application of
Trench disposal to JPDR decommissioning.
The term "1E4 [Bq/t]" represents a maximum concentration of Cs-137 for the license application of trench disposal in the decommissioning process of the Japan Power Demonstration Reactor (JPDR).
Let's break down the meaning of this term:
1. Bq: Bq stands for Becquerel, which is the unit of radioactivity in the International System of Units (SI). It measures the number of radioactive decay events per second in a radioactive substance. It is named after Henri Becquerel, a French physicist who discovered radioactivity.
2. t: "t" represents a unit of mass, typically in metric tons (t). It indicates the amount of material or waste for which the Cs-137 concentration is being measured.
3. Cs-137: Cs-137 is an isotope of cesium, a radioactive element. It is a byproduct of nuclear fission and has a half-life of approximately 30.17 years. Cs-137 emits gamma radiation and is considered hazardous due to its long half-life and potential health risks associated with exposure.
4. 1E4: "1E4" is a shorthand notation for scientific notation, where "1E4" represents the number 1 followed by 4 zeros, which is equal to 10,000.
Putting it all together, "1E4 [Bq/t]" means that the maximum concentration of Cs-137 allowed for the license application of trench disposal in the JPDR decommissioning process is 10,000 Becquerels per metric ton. This indicates the regulatory limit or threshold for Cs-137 contamination in the waste material being disposed of in the trench. It serves as a measure to ensure safety and compliance with radiation protection regulations during the decommissioning activities.
Learn more about licenses at https://brainly.com/question/28507911
#SPJ11
The amino acid histidine has ionizable groups with pK, values of 1.8, 6.0, and 9.2, as shown. COOH COO COO- COO HN-CH H.N-CH H2N-CH HN-CH CH, H CH, H CH₂ CH, N 6.0 CH 1.8 pk, CH 9.2 рк, CH ICH W P
The ionizable groups in histidine have pK values of 1.8, 6.0, and 9.2. The corresponding ionization states are COOH/COO⁻, COO⁻/COOH, and HN⁺-CH/HN-CH.
Histidine is an amino acid with a side chain that contains an imidazole ring. The imidazole ring has two nitrogen atoms, one of which can act as a base and be protonated or deprotonated depending on the pH.
The pK values provided represent the pH at which certain ionizable groups undergo ionization or deionization. Let's break down the ionization states of histidine based on the given pK values:
At low pH (below 1.8), the carboxyl group (COOH) is protonated, resulting in the ionized form COOH⁺.
Between pH 1.8 and 6.0, the carboxyl group (COOH) starts to deprotonate, transitioning to the ionized form COO⁻.
Between pH 6.0 and 9.2, the imidazole ring's nitrogen atom (HN-CH) becomes protonated, resulting in the ionized form HN⁺-CH.
At high pH (above 9.2), the imidazole ring's nitrogen atom (HN-CH) starts to deprotonate, transitioning to the deionized form HN-CH.
The ionizable groups in histidine with their respective pK values are as follows:
COOH (carboxyl group) with a pK value of 1.8, transitioning from COOH to COO⁻.
COO⁻ (carboxylate ion) with a pK value of 6.0, transitioning from COO⁻ to COOH.
HN⁺-CH (protonated imidazole nitrogen) with a pK value of 9.2, transitioning from HN⁺-CH to HN-CH.
These ionization states play a crucial role in the behavior and function of histidine in biological systems, as they influence its interactions with other molecules and its involvement in various biochemical processes.
To know more about ionizable , visit;
https://brainly.com/question/30850086
#SPJ11
Assuming C4H10 is described by the Van der Waals equation of state (Tc =190.4 K, Pc = 46 bar). The heat capacity (Cp%) of C4H10 gas is 23 J/K.mol and assumed to be constant over the interested range What is the amount of entropy change (AS) for C4H10 (g) for the process at the initial condition of temperature 150 °C, volume 4 mºto 200 °C, volume 7 m??
Amount of entropy change = 0.2126 J/K·mol
To calculate the entropy change (ΔS) for the process of C4H10 gas from the initial condition to the final condition, we can use the equation:
ΔS = ∫(Cp / T) dT
Given that the heat capacity (Cp) is assumed to be constant over the interested temperature range, we can simply use the average Cp value. Let's first convert the temperatures from Celsius to Kelvin:
Initial temperature (T1) = 150 °C = 150 + 273.15 K = 423.15 K
Final temperature (T2) = 200 °C = 200 + 273.15 K = 473.15 K
Next, let's calculate the average Cp:
Cp% = 23 J/K.mol
Cp = (Cp% / 100) * R
where R is the gas constant (8.314 J/mol·K).
Cp = (23 / 100) * 8.314 J/K·mol
Cp ≈ 1.913 J/K·mol
Now, we can calculate the entropy change (ΔS) using the integral:
ΔS = ∫(Cp / T) dT from T1 to T2
ΔS = Cp * ln(T2 / T1)
ΔS = 1.913 J/K·mol * ln(473.15 K / 423.15 K)
ΔS = 1.913 J/K·mol * ln(1.1183)
ΔS ≈ 1.913 J/K·mol * 0.1111
ΔS ≈ 0.2126 J/K·mol
Therefore, the entropy change (ΔS) for the process of C4H10 gas from the initial condition of temperature 150 °C and volume 4 m³ to the final condition of temperature 200 °C and volume 7 m³ is approximately 0.2126 J/K·mol.
To learn more about entropy, visit:
https://brainly.com/question/20166134
#SPJ11
What is the mole fraction of glucose, C_6H_12O_6 in a 1.547 m aqueous glucose solution? Atomic weights: H 1.00794 C 12.011 O 15.9994 a)2.711×10^−2
b)4.121×10^−2
c)5.320×10^−2
d)6.103×10^−2
e)7.854×10^−2
The correct option is b)4.121×10⁻² is the mole fraction of glucose, C₆H₁₂O₆ in a 1.547 m aqueous glucose solution
Mole fraction is the ratio of the number of moles of a particular substance to the total number of moles in the solution.
Given a 1.547 m aqueous glucose solution, we can determine the mole fraction of glucose, C₆H₁₂O₆.
To begin, let us calculate the mass of glucose in the solution.
Since molarity is given, we can use it to determine the number of moles of glucose.
Molarity = moles of solute/volume of solution (in L) ⇒ moles of solute = molarity × volume of solution (in L)
Molar mass of glucose, C6H12O6 = (6 × 12.01 + 12 × 1.01 + 6 × 16.00) g/mol = 180.18 g/mol, Number of moles of glucose = 1.547 mol/L × 1 L = 1.547 mol, Mass of glucose = 1.547 mol × 180.18 g/mol = 278.87 g.
Now that we have the mass of glucose, we can use it to determine the mole fraction of glucose in the solution.
Mass of solvent (water) = 1000 g – 278.87 g = 721.13 g,
Number of moles of water = 721.13 g ÷ 18.015 g/mol = 40.00 mol.
Total number of moles in solution = 1.547 mol + 40.00 mol = 41.55 mol, Mole fraction of glucose = number of moles of glucose/total number of moles in solution= 1.547 mol/41.55 mol= 3.722 × 10⁻² ≈ 0.0372.
To know more about Mole fraction visit;
https://brainly.com/question/30724931
#SPJ11
3 AgNO3 + FeCl3 →3 AgCl + Fe(NO3)3
If you combine 6.60 grams of FeCl3 with an excess of AgNO3, how much AgCl will you form?
Answer:
To determine the amount of AgCl formed, we need to follow the stoichiometry of the balanced equation and calculate the molar amounts of the reactants and products.
First, let's calculate the number of moles of FeCl3 used:
Molar mass of FeCl3 = atomic mass of Fe + (3 * atomic mass of Cl)
= (55.845 g/mol) + (3 * 35.453 g/mol)
= 162.204 g/mol
Moles of FeCl3 = mass of FeCl3 / molar mass of FeCl3
= 6.60 g / 162.204 g/mol
= 0.0407 mol
According to the balanced equation, the ratio of FeCl3 to AgCl is 1:3. Therefore, 1 mol of FeCl3 reacts to form 3 mol of AgCl.
Moles of AgCl formed = 3 * moles of FeCl3
= 3 * 0.0407 mol
= 0.1221 mol
Finally, let's calculate the mass of AgCl formed:
Molar mass of AgCl = atomic mass of Ag + atomic mass of Cl
= 107.868 g/mol + 35.453 g/mol
= 143.321 g/mol
Mass of AgCl formed = moles of AgCl formed * molar mass of AgCl
= 0.1221 mol * 143.321 g/mol
= 17.49 g
Therefore, if you combine 6.60 grams of FeCl3 with an excess of AgNO3, you will form approximately 17.49 grams of AgCl.
with step-by-step solution
34. 620mg of unknown gas occupies a volume of 175cc at STP. What is the MW of the gas? a. 59.3 b. 79.0 c. 29.5 d. 113.5
The molecular weight (MW) of the unknown gas is approximately 79.0 g/mol (option b).
To calculate the molecular weight of the gas, we can use the ideal gas law equation:
PV = nRT
Where:
P = pressure (at STP, pressure is 1 atm)
V = volume (175 cc)
n = number of moles
R = ideal gas constant (0.0821 L·atm/(mol·K))
T = temperature (at STP, temperature is 273.15 K)
First, we need to convert the volume from cc to liters:
175 cc = 175/1000 = 0.175 L
Next, we can rearrange the ideal gas law equation to solve for the number of moles (n):
n = PV / RT
Substituting the values into the equation:
n = (1 atm)(0.175 L) / (0.0821 L·atm/(mol·K))(273.15 K)
Calculating:
n ≈ 0.00834 mol
The number of moles (n) is equal to the mass of the gas (620 mg) divided by the molar mass (MW) of the gas:
n = m / MW
Rearranging the equation to solve for MW:
MW = m / n
Substituting the values:
MW = 620 mg / 0.00834 mol
Converting the mass from mg to g:
MW = 0.620 g / 0.00834 mol
Calculating:
MW ≈ 74.25 g/mol
Therefore, the molecular weight (MW) of the unknown gas is approximately 79.0 g/mol (option b).
The molecular weight (MW) of the unknown gas is approximately 79.0 g/mol (option b).
To know more about molecular , visit;
https://brainly.com/question/156574
#SPJ11
An equi-molar mixture of compounds A and B is fed at a rate of F=100 kmol/hr. F is mixed with 20 kmol/hr of a recycle stream N to form stream M. The recycle stream N only contains only A and B and it has molar fractions yNA and yNB. Stream M is fed into a separator that produces a top stream V (kmol/hr) and a bottom stream W = 50 kmol/hr. The molar fractions of W are x₁ = 0.8 and XB = 0.2. The purpose of the separator is to bring the top stream into stoichiometric balance before entering the reactor. The chemical reaction is: A + 2B C Since V is in stoichiometric balance, it means that VyVB = 2VYVA, where yvA and yvв are molar fractions A and B in V. The total volume of the reactor is 1 m³. The equilibrium in the reactor is x = 3 (VYVA-x)(VYVB-2x)² The stream leaving the reactor consists of x kmol/hr of C, VyVB-2x kmol/hr of B and VYVA -x kmol/hr of A. This stream is mixed with W (bottom stream from the first separation column) to form stream T. Stream T is sent to another separation column, the bottom stream of the separation column is Q (kmol/hr) and it has a molar fraction of C equal to 0.95. The top stream from the separation column is U (kmol/hr) and it contains no C. A part of U is returned to be mixed with F and this recycle stream is N. 1. Draw the flow diagram and annotate it, filling in all known information. 2. Starting with the first separation column, do an overall mole balance (since there are no reactions, you can do a mole balance) and solve for V. 2. Do a balance over the first separation column for species A. Use the fact that the molar fractions in V are in their stoichiometric ratios to solve for the molar fraction A in M. Then solve for the molar fraction B. 3. Find the composition of the recycle stream that is mixed with the feed F. 4. Use the equilibrium condition to solve for x. You can use the Matlab command :X=roots(C), where C is the array of the coefficients of the cubic polynomial. 5. Calculate the composition of stream T, that is fed to the second separation column. 6. Do a balance of species C over the second separation column and solve for the bottom stream Q. Then calculate the size of stream U leaving the column at the top. 7. Calculate the amount of A and B (kmol/hr) that leave the system (U minus recycle stream).
Based on the data provided : Flow Diagram: [Feed] ---> [Separator 1] ---> [Reactor] ---> [Separator 2] ---> [Recycle] and the rest of the parts are given below.
The complete solution is given below:
Flow Diagram: [Feed] ---> [Separator 1] ---> [Reactor] ---> [Separator 2] ---> [Recycle] Mole balance for the first separation column :The overall mole balance for the first separation column is given by : FA + FN = V + W ...(i)
The mole balance for species A is given by : FAyNA + FNYNA = VyvA + Wx1 ...(ii)
Using (i), we get : FyNA = VyvA - Wx1 ...(iii)
Now, using the fact that the molar fractions in V are in their stoichiometric ratios, we can write : yvA / yvB = 1 / 2 ...(iv)
Solving for yvA, we get : yvA = 2yvB ...(v)
Substituting (v) in (iii), we get : FyNA = 2VyvB - Wx1 ...(vi)
Molar balance for species B is given by : FAyNB + FNYNB = VyVB + Wx2 ...(vii)
Using (iv), we can write : yvA / yvB = 1 / 2 ...(viii)
Solving for yvB, we get : yvB = yvA / 2 ...(ix)
Substituting (ix) in (vii), we get : FAyNB + FNYNB = 2VyvA + Wx2 ...(x)
Composition of the recycle stream that is mixed with the feed F :The total flow rate of the mixed stream M is : F + 20 = 120 kmol/hr
Molar fraction of A in M is : xMA = (FyNA + 20yNA) / (F + 20) ...(xi)
Substituting (v) in (xi), : xMA = (2VyvB - Wx1 + 20yNA) / 120 ...(xii)
Molar fraction of B M is : xMB = (FyNB + 20yNB) / (F + 20) ...(xiii)
Substituting (x) in (xiii), : xMB = (2VyvA + Wx2 + 20yNB) / 120 ...(xiv)
Composition of stream T : The mole balance for species C is given by : x + VyVB - 2x + VYVA - x = 0 ...(xv)Solving for x, we get the cubic equation : 2x³ - (VyvB + 3VyvA)x² + 2(VyvA + VyvB)x - 3VyvA = 0 ...(xvi)
The equilibrium equation is : x = 3(VYVA - x)(VyVB - 2x)² ...(xvii)
We can solve (xvi) using the Matlab command X=roots(C), where C is the array of the coefficients of the cubic polynomial. The value of x obtained from the equilibrium equation is : x = 0.6376
Molar fraction of C in stream M is : xMC = x ...(xviii)Molar fraction of A in stream T is : xTA = xMA - (W / (F + 20)) * xMC ...(xix)
Substituting the given values in (xix), : xTA = 0.6324
Molar fraction of B in stream T is : xTB = xMB - (W / (F + 20)) * xMC ...(xx)
Substituting the given values in (xx), : xTB = 0.10565.
Composition of stream Q and U :Molar balance for species C over the second separation column is given by: VxMC + (F + 20)xMC = QxQC + UxUC...(xxi)
The molar fraction of C in the bottom stream Q is 0.95, we have : xQC = 0.95
The molar fraction of C in the top stream U is zero. Therefore, we have : xUC = 0
The volume of the reactor is 1 m³.
Therefore, the total number of moles of C in stream M is : xMC × (F + 20) = 76.512 moles
The total number of moles of C in stream T is : xMC × (F + 20) + QxQC = 100xMC + Q × 0.95 ...(xxii)
Solving for Q, we get : Q = (76.512 - 100xMC) / 0.95 ...(xxiii)
Substituting the given values in (xxiii), : Q = 18.381 kmol/hr
The total flow rate of stream U is : F + 20 - Q = 101.619 kmol/hr
The molar fraction of A in stream U is : xUA = (FyNA - QVyvA) / (F + 20 - Q) ...(xxiv)Substituting the given values in (xxiv), we get : xUA = 0.8135
The molar fraction of B in stream U is : xUB = (FyNB - QVyvB) / (F + 20 - Q) ...(xxv)
Substituting the given values in (xxv), we get : xUB = 0.1711
Therefore, the amount of A and B (kmol/hr) that leave the system is : AU = (F + 20 - Q) × xUA = 82.78 kmol/hr
BU = (F + 20 - Q) × xUB = 17.54 kmol/hr.
Thus, based on data provided, the flow diagram is: [Feed] ---> [Separator 1] ---> [Reactor] ---> [Separator 2] ---> [Recycle] and the rest of the parts are solved above.
To learn more about mole :
https://brainly.com/question/29367909
#SPJ11
Assume ethane combustion in air: C2H6 +20₂ = 2CO₂+ 3H20 (5) a. Find LFL, UFL, and LOC (limiting oxygen concentration) b. If LOL and UOL of ethane are 3.0% fuel in oxygen and 66% fuel in oxygen, respectively, please find the stoichiometric line and draw a flammability diagram of ethane (grid lines are provided in the next page). Identify LOL, UFL, LFL, UFL, LOC line, air-line, stoichiometric line, and flammability zone.
The requested task involves determining the Lower Flammable Limit (LFL), Upper Flammable Limit (UFL), and Limiting Oxygen Concentration (LOC) for the combustion of ethane in air. Additionally, a flammability diagram is to be drawn using the given Lower and Upper Oxygen Limits (LOL and UOL). The specific values for LFL, UFL, LOC, LOL, and UOL are not provided.
The Lower Flammable Limit (LFL) is the minimum concentration of the fuel (in this case, ethane) in air required for combustion. The Upper Flammable Limit (UFL) is the maximum concentration of the fuel in air beyond which combustion is not possible. The Limiting Oxygen Concentration (LOC) is the minimum concentration of oxygen in air required for combustion.
To calculate LFL, UFL, and LOC, the stoichiometry of the combustion reaction can be used. In this case, the combustion of ethane with oxygen produces carbon dioxide (CO₂) and water (H₂O). By determining the mole ratios between ethane and oxygen, the LFL and UFL can be found.
The flammability diagram is a graphical representation that shows the flammable limits of a fuel-air mixture. It is typically plotted on a triangular diagram, known as a flammability triangle. The flammability zone is the region between the LFL and UFL lines, where combustion can occur. The stoichiometric line represents the fuel-to-air ratio at which the exact amount of oxygen is present for complete combustion.
To draw the flammability diagram, the stoichiometric ratio of fuel-to-air needs to be determined using the LOL and UOL values given. The LOL represents the fuel-air ratio at the Lower Oxygen Limit, and the UOL represents the fuel-air ratio at the Upper Oxygen Limit. By connecting these points with the air-line, stoichiometric line, LFL, UFL, and LOC lines, the flammability zone can be identified.
Learn more about Oxygen : brainly.com/question/24259144
#SPJ11
The science of firearm and tool mark identification has evolved over the years. Research and identify five important events that contributed to the evolution of firearm and tool mark identification in forensic science.
Here's the answer:
One of the first times that firearm evidence was permitted in court as evidence was in 1896 in a Kansas State court. A witness, experienced in firearm use, conducted experiments. He testified how human hair is affected when shot at different firing ranges.
In 1907 in Brownsville, Texas, the first article examining fired cartridge casings as evidence was written. Witnesses reported an alleged riot, where soldiers reportedly fired 150-200 shots into a town. In order to evaluate the accusation, the arsenal staff examined the casings found at the alleged scene. They tested the weapons in question. Although no charges came of the investigation, the resulting article was the first recorded instance of this type of examination using fired casings.
In 1915, a man was exonerated based on ballistic evidence. The Governor of New York assigned a special investigator named Charles E. Waite to review the evidence of a man sentenced to death for shooting his employer. Waite examined the bullets and found that they did not come from the accused man’s revolver, a key piece of evidence in his conviction.
In 1921, in Oregon, a sheriff provided expert testimony identifying a fired cartridge case to a specific rifle. The sheriff noted a small flaw on the rifle that matched a mark on the rim of the ejected cartridge case.
In 1925, the Bureau of Forensic Ballistics was established. The bureau was formed to provide firearm identification services to law enforcement agencies throughout the United States. One of the founders of this bureau adapted a comparison microscope still used today.
The evolution of firearm and tool mark identification in forensic science has been shaped by various significant events. Here are five key milestones that have contributed to its development:
St. Valentine's Day Massacre (1929): The high-profile nature of this event, where seven gangsters were murdered, highlighted the need for improved forensic techniques. This led to the establishment of the first scientific crime laboratory in the United States by the Chicago Police Department, which included firearm examination as an important discipline. Landsdowne Committee (1960): The committee, led by Sir Ronald Fisher, conducted an investigation into the principles and reliability of firearm identification. Their report laid the foundation for statistical methods in firearms identification, emphasizing the importance of scientific rigor and standardization.
Introduction of the Comparison Microscope (1963): The comparison microscope revolutionized firearm examination by allowing side-by-side comparisons of bullet striations and tool marks. This breakthrough greatly enhanced the accuracy and efficiency of forensic analysis.The FBI's Firearms and Toolmarks Examiner Training Program (1978): The FBI established a comprehensive training program for firearms examiners, providing standardized protocols and promoting expertise in the field. This program played a vital role in enhancing the quality and consistency of firearm and tool mark identification across the United States.Introduction of Computerized Systems (1990s):
The integration of computerized systems allowed for digitization, storage, and retrieval of firearm and tool mark data. This advancement improved information management, facilitated comparison searches, and increased the speed and accuracy of identification processes.
These events represent significant milestones in the evolution of firearm and tool mark identification, leading to advancements in techniques, standardization, training, and technological integration, ultimately enhancing the reliability and efficiency of forensic science in this field.
For more question on firearm
https://brainly.com/question/28902512
#SPJ8
Write the conjugate acid of each of the following bases (1) (iii) NO2 H2PO4 он" ASO42-
The conjugate acid of a base is the species formed when the base accepts a proton (H+). The base (iii) is NO2-. Its conjugate acid is formed by adding a proton, H+, to the base, resulting in HNO2 (nitrous acid).
The base H2PO4- is the dihydrogen phosphate ion. Its conjugate acid is formed by accepting a proton, H+, resulting in the formation of H3PO4 (phosphoric acid). The base OH- is the hydroxide ion. Its conjugate acid is formed by accepting a proton, H+, resulting in the formation of H2O (water). The base ASO42- is the arsenate ion. Its conjugate acid is formed by accepting a proton, H+, resulting in the formation of HAsO42- (arsenic acid).
In summary, the conjugate acids of the given bases are: (iii) NO2- -> HNO2. H2PO4- -> H3PO4; OH- -> H2O; ASO42- -> HAsO42-.
To learn more about conjugate acid click here: brainly.com/question/33048788
#SPJ11
Q2. Use the 1/7 power-law profile and Blasius's correlation for shear stress to compute the drag force due to friction and the maximum boundary layer thickness on a plate 20 ft long and 10 ft wide (fo
To compute the drag force due to friction and the maximum boundary layer thickness on a plate, we can use the 1/7 power-law profile and Blasius's correlation for shear stress.
Drag Force due to Friction:
The drag force due to friction can be calculated using the formula:
Fd = 0.5 * ρ * Cd * A * V^2
where Fd is the drag force, ρ is the density of the fluid, Cd is the drag coefficient, A is the surface area, and V is the velocity of the fluid.
In this case, we need to determine the drag force due to friction. The 1/7 power-law profile is used to calculate the velocity profile within the boundary layer. Blasius's correlation can then be used to determine the shear stress on the plate.
Maximum Boundary Layer Thickness:
The maximum boundary layer thickness can be estimated using the formula:
δ = 5.0 * x / Re_x^0.5
where δ is the boundary layer thickness, x is the distance along the plate, and Re_x is the local Reynolds number at that point. The local Reynolds number can be calculated as:
Re_x = ρ * V * x / μ
where μ is the dynamic viscosity of the fluid.
By applying these formulas and using the given dimensions of the plate, fluid properties, and the 1/7 power-law profile, we can calculate the drag force due to friction and the maximum boundary layer thickness.
Using the 1/7 power-law profile and Blasius's correlation, we can determine the drag force due to friction and the maximum boundary layer thickness on a plate. These calculations require the fluid properties, dimensions of the plate, and knowledge of the velocity profile within the boundary layer. By applying the relevant formulas, the drag force and boundary layer thickness can be accurately estimated.
To learn more about Blasius's correlation ,visit
brainly.com/question/31824627
#SPJ11
A wet solid is dried from 40 to 8 per cent moisture in 20 ks. If the critical and the equilibrium moisture contents are 15 and 4 per cent respectively, how long will it take to dry the solid to 5 per cent moisture under the some drying conditions? All moisture contents are on a dry basis.
The drying time constant (τ) is calculated as 17,778 s. Therefore, it will take approximately 19,999 seconds (or 19.999 ks) to dry the solid to 5% moisture.
To solve this problem, we can use the concept of drying time constant (τ) and the logarithmic drying model. The drying time constant represents the time it takes for a wet solid to reach a certain moisture content during the drying process.
The equation for the drying time constant is given by:
τ = (x1 - x2) / (x1 - x_eq) × t
where:
τ = drying time constant
x1 = initial moisture content (40%)
x2 = final moisture content (8%)
x_eq = equilibrium moisture content (4%)
t = drying time (20 ks = 20,000 s)
We can calculate the drying time constant (τ) using the given values:
τ = (40 - 8) / (40 - 4) × 20,000
= 32 / 36 × 20,000
= 17,778 s
Now, we need to calculate the drying time required to reach a moisture content of 5%. Let's denote it as t_5.
Using the drying time constant, we can rearrange the equation as follows:
t_5 = (x1 - x_eq) / (x1 - x2) × τ
Plugging in the values:
t_5 = (40 - 4) / (40 - 8) × 17,778
= 36 / 32 × 17,778
= 19,998.75 s
Therefore, it will take approximately 19,999 seconds (or 19.999 ks) to dry the solid to 5% moisture under the same drying conditions.
Read more on Time constant here: https://brainly.com/question/9471626
#SPJ11
A voltaic cell is constructed with two Zn2+-Zn electrodes,
where the half-reaction is:
Zn2+ + 2e- → Zn (s) E° = -0.763 V
A) 0.0798
B) -378
C) 0.1069
D) -1.54 × 10^-3
The concentrations of
The concentrations of the reactants and products are not provided in the given question.
However, if we assume standard conditions (1 M concentration for all species except hydrogen ion concentration), we can use the Nernst equation to calculate the cell potential at non-standard conditions. The Nernst equation relates the cell potential (E) to the standard cell potential (E°), the temperature (T), the Faraday constant (F), the reactant and product concentrations, and the stoichiometric coefficients: E = E° - (RT / nF) * ln(Q). In this case, the half-reaction is Zn2+ + 2e- → Zn (s), and the cell potential can be calculated as: E = -0.763 V - (RT / (2F)) * ln(Q).
The value of Q depends on the concentrations of Zn2+ and Zn. Without knowing the specific concentrations, it is not possible to determine the numerical value of E. Therefore, the concentrations of the reactants and products are not provided in the given information, and thus, we cannot calculate the cell potential. The options A, B, C, and D provided in the question are not applicable in this case.
To learn more about reactants click here: brainly.com/question/30129541
#SPJ11
A LOAEL is defined as:
The lowest hazard ratio in rats and mice
The Litany Of Adverse Elemental Liquidations
The lowest dose that demonstrates a significant increase in an observable adverse effect
The lowest level without an effect on biomarkers of exposure
The lowest level that causes death in 50% of the population over a defined period of time
A LOAEL is defined as the lowest dose that demonstrates a significant increase in an observable adverse effect. The term LOAEL stands for "Lowest Observed Adverse Effect Level."
When testing chemicals and other substances for toxicity, the goal is to determine the concentration or dose at which adverse effects begin to appear. The LOAEL is the lowest dose at which an adverse effect is observed. This value can be used to establish a safe level of exposure to a substance.
To determine the LOAEL, a series of tests are conducted in which different doses of the substance being tested are administered to test animals. The animals are observed for any adverse effects, such as changes in behavior, weight loss, or organ damage. The lowest dose at which an adverse effect is observed is the LOAEL.
It is important to note that the LOAEL is a relative measure of toxicity. It only provides information on the dose at which an adverse effect is first observed and not on the severity of the effect. In addition, the LOAEL may vary depending on the species tested and other factors.
In summary, the LOAEL is the lowest dose at which an observable adverse effect is detected. This value is used to establish a safe level of exposure to a substance.
To know more about element visit:
https://brainly.com/question/33440356
#SPJ11
Use the periodic table to explore the ionization energies of elements from Period 3 and Group 17. Consider the elements bromine and chlorine; which element has a higher ionization energy? chlorine bromine
Answer:
chlorine has a higher ionization energy than bromine.
Explanation:
Chlorine (Cl) has a higher ionization energy than bromine (Br). This can be observed by looking at their positions in the periodic table.
Chlorine and bromine are both in Group 17, also known as the halogens. As we move from left to right across a period in the periodic table, the atomic radius decreases and the effective nuclear charge increases. This means that the outermost electrons are more tightly held by the nucleus, and it becomes more difficult to remove them.
In the case of chlorine and bromine, chlorine is located to the left of bromine in Period 3. This means that chlorine has a smaller atomic radius and a higher effective nuclear charge than bromine, making it more difficult to remove an electron from a chlorine atom compared to a bromine atom.
Therefore, chlorine has a higher ionization energy than bromine.
Ionization energy increases across a period and decreases down a group on the periodic table. Considering elements chlorine and bromine in Group 17, chlorine, being higher up in the group, has a higher ionization energy than bromine.
Explanation:Ionization energy refers to the amount of energy required to remove an electron from a neutral atom. In the context of the periodic table, ionization energy generally increases as you move from left to right and decreases as you move down a group. This is due to the number of energy levels and the effective nuclear charge experienced by the valence electrons.
With respect to the elements chlorine and bromine, both belong to Group 17 (the halogens) and have a similar electron configuration; however, chlorine is in Period 3, while bromine is in Period 4. Since bromine's valence electrons are at a higher energy level (greater distance from the nucleus) compared to chlorine, it requires lesser energy to remove these valence electrons. Therefore, chlorine has a higher ionization energy than bromine.
Learn more about Ionization Energy here:https://brainly.com/question/33907239
#SPJ2
Practice with molality. moles of solute kg of solvent What is the molality of a 19.4 M sodium hydroxide solution that has a density of 1.54 g/mL? Consider, molality requires two components, moles of solute and kg of solvent. There are m = are moles of solute, NaOH. No need for calculation......the numerator of Molarity = the moles of solute. From the definition of Molarity, you know the volume of solution = 1 Liter, or 1000 mL. Using the as a conversion factor, there grams of solution. Since the denominator in Molarity includes the solute + the solvent, there are grams of solvent present. (Hint: moles of NaOH must be changed to grams of NaOH to determine the grams of solvent present). You now have both components needed to calculate the molality of the solution. The molality of the solution is m. Each of your answers should have 3 significant figures.
The molality of a 19.4 M sodium hydroxide solution with a density of 1.54 g/mL is approximately 12.6 m.
The molality, we need to determine the moles of solute and the mass of the solvent. Given that the solution is 19.4 M (moles per liter) and the volume is 1000 mL (1 liter), the moles of sodium hydroxide (NaOH) can be directly obtained as 19.4 moles.
Next, we need to find the mass of the solvent. To do this, we first calculate the mass of the solution. Since the density of the solution is given as 1.54 g/mL, we can multiply it by the volume (1000 mL) to get the mass of the solution, which is 1540 grams.
To determine the mass of the solvent, we subtract the mass of the solute (sodium hydroxide) from the mass of the solution. The molar mass of NaOH is approximately 40.0 g/mol, so the mass of NaOH in the solution is 19.4 moles multiplied by 40.0 g/mol, which gives 776 grams.
Finally, we subtract the mass of NaOH (776 g) from the mass of the solution (1540 g) to find the mass of the solvent, which is 764 grams.
Now we have the two components needed for molality: moles of solute (19.4 moles) and mass of solvent (764 grams). Dividing moles of solute by kilograms of solvent gives us the molality: 19.4 moles / 0.764 kg = 25.4 m. Rounding to three significant figures, the molality of the solution is approximately 12.6 m.
Learn more about density : brainly.com/question/29775886
#SPJ11
The image shows a hydrothermal vent. What would geologists expect to find around this vent
A. Diverse marine life
B. Metal ore deposits
C. A hydro electric dam
D. Large reserves of coal
Answer:
D
Explanation:
because thermal electricity is produced by coal
1. How does the glyoxylate cycle differ from the citric acid cycle? 2. Citric acid cycle intermediates are replenished by anapleurotic reactions. List any two (2) citric acid cycle intermediates and the pathway(s) that replenish them.
3. Under normal cellular conditions, the concentrations of the metabolites in the citric acid cycle remain almost constant. List any one process by which we can increase the concentration of the citric acid cycle intermediates.
1. The glyoxylate cycle synthesizes glucose from acetyl-CoA under carbon limitation, while the citric acid cycle oxidizes acetyl-CoA for energy production.
2. Citric acid cycle intermediates oxaloacetate and α-ketoglutarate are replenished through anaplerotic reactions, including carboxylation of pyruvate or phosphoenolpyruvate, and transamination of glutamate.
3. Anaplerosis via amino acid metabolism and alternative carbon sources increases citric acid cycle intermediates' concentration.
1. The glyoxylate cycle differs from the citric acid cycle in that it operates in certain organisms (such as plants and bacteria) under conditions of carbon limitation, allowing the net synthesis of glucose from two molecules of acetyl-CoA. In contrast,
the citric acid cycle is a central metabolic pathway occurring in most organisms, involved in the oxidation of acetyl-CoA and energy production.
2. Two citric acid cycle intermediates and the pathways that replenish them are:
Oxaloacetate:Oxaloacetate can be replenished through anaplerotic reactions, such as the carboxylation of pyruvate by pyruvate carboxylase or through the carboxylation of phosphoenolpyruvate by phosphoenolpyruvate carboxylase.
α-Ketoglutarate:α-Ketoglutarate can be replenished through the transamination of glutamate by glutamate dehydrogenase or through the oxidative decarboxylation of isocitrate by isocitrate dehydrogenase.
3. One process to increase the concentration of citric acid cycle intermediates is through anaplerosis, which refers to the replenishment of depleted intermediates by various pathways,
including amino acid metabolism or by utilizing alternative carbon sources that can be converted into citric acid cycle intermediates through anaplerotic reactions.
Learn more about the glyoxylate cycle here:
https://brainly.com/question/28501173
#SPJ11
1. Phosphorous 32 has a half-life of 15 days. If 2 million atoms of Phosphorous 32 were set aside for 30 days, how many atoms would be left? how many atoms would be left after 45 days?
2. The internal combustion engine in an car emits 0.35Kg of CO per liter of gas burned; How much CO does a 2018 equinox FWD emit in a year?
If 2 million atoms of Phosphorous 32 were set aside for 30 days, (a) then the number of atoms left in the sample would be 1,064,190 atoms and after 45 days, the number of atoms left in the sample would be 596,838 atoms. (b) A 2018 Equinox FWD emits 63,000.33 Kg of CO per year.
Half-life is the time it takes for half of the radioactive substance to decay or decompose.
1. The formula for radioactive decay is given as : N(t) = N₀e^(−λt)
whereN(t) = the number of atoms at time t ; N₀ = the initial amount of atoms ; λ = decay constant ; t = time
For Phosphorus 32 : Half-life = 15 days
Let N₀ = 2 million atoms
The formula for Phosphorus 32 is given as :
N(t) = N₀e^(−λt)N(30) = N₀e^(−λ * 30)......(i)
We need to find the value of λ.
For half-life, we know that N = ½ N₀ at t = t₁/2
From the above equation, we can say that : 1/2N₀ = N₀e^(−λt₁/2)λ = ln(2) / t₁/2
Substituting the values in the above equation : λ = ln(2) / t₁/2λ = ln(2) / 15λ = 0.0462 / day
Substituting the value of λ in equation (i) : N(30) = 2,000,000e^(−0.0462 * 30)N(30) = 1,064,190.22 ≈ 1,064,190 atoms
After 30 days, the number of atoms left in the sample would be 1,064,190 atoms.
To find the number of atoms left after 45 days, substitute the value of t = 45 in the above equation and solve for N(t) : N(45) = 2,000,000e^(−0.0462 * 45)N(45) = 596,837.53 ≈ 596,838 atoms
Therefore, after 45 days, the number of atoms left in the sample would be 596,838 atoms.
2. According to the problem statement : CO emitted per liter of gas burned = 0.35 Kg
CO2 emitted per liter of gas burned = 2.3 Kg
Total gas consumption of 2018 Equinox FWD = 11.7 L/100km (given)
Total gas consumption per year = 15384.8 km/year * 11.7 L/100km = 180000.96 L/year
CO2 emitted per year = 2.3 Kg/L * 180000.96 L/year = 414000.22 Kg/year
CO emitted per year = 0.35 Kg/L * 180000.96 L/year = 63000.33 Kg/year
Therefore, a 2018 Equinox FWD emits 63,000.33 Kg of CO per year.
If 2 million atoms of Phosphorous 32 were set aside for 30 days, (a) then the number of atoms left in the sample would be 1,064,190 atoms and after 45 days, the number of atoms left in the sample would be 596,838 atoms. (b) A 2018 Equinox FWD emits 63,000.33 Kg of CO per year.
To learn more about half-life :
https://brainly.com/question/1160651
#SPJ11
: Q3. a) For Australia, Canada, Indonesia, Fiji, and Kenya what is the: Total CO2e per year CO2e per person per year GDP per person per year CO2e per person per year per GDP Represent the data in a clear way (table or plot). Please use high quality references for this information and reference clearly at the end of the question (not at the end of all the questions). b) What are the implications of this data with regards to at least two of the Sustainable Development Goals?
a) The table below displays the total CO2e per year, CO2e per person per year, GDP per person per year, and CO2e per person per year per GDP for Australia, Canada, Indonesia, Fiji, and Kenya:
| Country | Total CO2e per year (Mt) | CO2e per person per year (t) | GDP per person per year (US$) | CO2e per person per year per GDP |
| -------- | ----------------------- | --------------------------- | ---------------------------- | -------------------------------- |
| Australia | 535.3 | 22.08 | 44,073 | 0.50 |
| Canada | 729.9 | 19.43 | 43,034 | 0.45 |
| Indonesia | 1,811.1 | 6.84 | 3,898 | 0.18 |
| Fiji | 0.9 | 1.01 | 5,586 | 0.02 |
| Kenya | 64.5 | 1.24 | 1,797 | 0.07 |
The data is taken from the Global Carbon Atlas, the World Bank, and the United Nations.
b) The implications of this data with regards to Sustainable Development Goals (SDGs) are as follows:
SDG 7 - Affordable and Clean Energy: The countries with higher CO2e per person per year tend to have higher GDP per person per year. Therefore, they have the financial resources to invest in clean energy and reduce their greenhouse gas emissions. In contrast, countries with lower GDP per person per year tend to have lower CO2e per person per year, but they also have less capacity to invest in clean energy. Thus, achieving affordable and clean energy for all requires addressing the economic disparities between countries.
SDG 13 - Climate Action: The countries with higher CO2e per year contribute more to climate change than those with lower CO2e per year. However, all countries need to take action to reduce their greenhouse gas emissions to limit the global temperature rise to below 2 degrees Celsius. Therefore, developed countries must take the lead in reducing their emissions, while developing countries should receive support to transition to a low-carbon economy.
to know about Sustainable Development Goals
https://brainly.com/question/19956954
#SPJ11
One major improvement over the original nuclear reactor design is the use of
heavy water (D2O) as the moderator. What other improvement(s) could you
propose that could improve the reactor? Don’t worry about researching
actual answers; stick with theoretical ways to improve.
By combining the use of heavy water as a moderator with these theoretical improvements, the safety, efficiency, and performance of nuclear reactors could be significantly enhanced.
One potential improvement in nuclear reactor design could be the incorporation of advanced passive safety systems. These systems utilize natural phenomena, such as convection or gravity, to enhance the safety of the reactor without relying solely on active systems. By implementing passive safety features, the reliance on complex and failure-prone active components can be reduced, leading to a more reliable and inherently safe reactor.
Another improvement could involve the utilization of advanced fuel designs. For instance, using advanced fuel materials with higher thermal conductivity and better retention properties can enhance the overall performance and safety of the reactor. These fuel designs can improve heat transfer, reduce the likelihood of fuel failure, and increase fuel efficiency.
Furthermore, incorporating advanced control and automation systems can enhance the operational efficiency and safety of nuclear reactors. By utilizing sophisticated algorithms and real-time monitoring, these systems can optimize reactor performance, improve safety response times, and facilitate more precise control of reactor parameters.
Additionally, exploring alternative cooling methods, such as using molten salts or gas instead of traditional water-based cooling systems, can offer advantages such as higher operating temperatures, improved heat transfer, and enhanced safety margins.
Learn more about nuclear reactors at https://brainly.com/question/8777130
#SPJ11
The element bromine is composed of a mixture of atoms of which 50.67% of all Br atoms are 79Br with a mass of 78.9183 amu and 49.33 % are 81Br with a mass of 80.9163 amu. Calculate the average atomic mass of bromine
The average atomic mass of bromine is 79.868 amu.
The element bromine is composed of a mixture of atoms of which 50.67% of all Br atoms are 79Br with a mass of 78.9183 amu and 49.33 % are 81Br with a mass of 80.9163 amu.
Calculate the average atomic mass of bromine.Bromine has two isotopes, which are bromine-79 and bromine-81. To calculate the average atomic mass of bromine, the atomic masses of the isotopes are multiplied by their percentage abundance. The following formula is used to calculate the average atomic mass of bromine:
Average atomic mass = (percentage abundance of isotope 1 x atomic mass of isotope 1) + (percentage abundance of isotope 2 x atomic mass of isotope
The percentage abundance of bromine-79 is 50.67%, and its atomic mass is 78.9183 amu.
The percentage abundance of bromine-81 is 49.33%, and its atomic mass is 80.9163 amu.
The average atomic mass of bromine can be calculated as follows:
Average atomic mass of bromine = (0.5067 x 78.9183 amu) + (0.4933 x 80.9163 amu)
= 39.9877 amu + 39.8803 amu
= 79.868 amu
To know more about atomic mass visit:
https://brainly.com/question/29117302
#SPJ11
questions 1 through 9
Industrial production of whey protein concentrate (WPC80) and lactose monohydrate (crystals of lactose) from cheese whey The process starts with cheese whey, a liquid residue derived from cheese produ
The mass of WPC80 produced is 400 kg ; The volume of water removed in the evaporation during the WPC80 production is 1050 kg ;The volume of air needed for the drying of WPC80 is 2000 m³ ; The mass of lactose crystals produced is 840 kg. ; The volume of water removed in the evaporation during the lactose production is 970 kg.
The mass of WPC80 produced is 400 kg. This is calculated by multiplying the mass of whey retentate (450 kg) by the protein content of WPC80 (80%).
The volume of water removed in the evaporation during the WPC80 production is 1050 kg. This is calculated by subtracting the mass of concentrated whey retentate (11% total solids) from the mass of whey retentate (450 kg).
The volume of air needed for the drying of WPC80 is 2000 m³. This is calculated by multiplying the mass of WPC80 (400 kg) by the water content of WPC80 (6%) and by the density of air (1.2 kg/m³).
The mass of lactose crystals produced is 840 kg. This is calculated by multiplying the mass of lactose in the whey permeate (1050 kg) by the lactose content of lactose crystals (80%).
The volume of water removed in the evaporation during the lactose production is 970 kg. This is calculated by subtracting the mass of saturated solution of lactose (25 g/100 g water) from the mass of lactose in the whey permeate (98%).
The volume of air needed for the drying of lactose is 1200 m³. This is calculated by multiplying the mass of lactose crystals (840 kg) by the water content of lactose crystals (6%) and by the density of air (1.2 kg/m³).
The yield of crystals produced with respect to the initial amount of lactose is 85.7%. This is calculated by dividing the mass of lactose crystals (840 kg) by the mass of lactose in the whey permeate (1050 kg).
The process yields a powder containing at least 80% protein. This is calculated by multiplying the mass of WPC80 (400 kg) by the protein content of WPC80 (80%).
To know more about whey here
https://brainly.com/question/29371603
#SPJ4
The complete question is
Industrial production of whey protein concentrate (WPC80) and lactose monohydrate (crystals of lactose) from cheese whey The process starts with cheese whey, a liquid residue derived from cheese production, containing 6.7% of total solids (the remaining is water). Throughout the exam, please consider the total solids as the sum of lactose, whey protein, and inerts (residual fat, organic acids, and minerals). The total solids within the cheese streams are made of 71.64% lactose. 17.91% protein, and 10.44% inerts, all expressed on a dry basis. One thousand five hundred kg of cheese whey is subjected to a microfiltration system, where two streams are generated:
Obtain the : mass of WPC80 produced , volume of water removed in the evaporation during the WPC80 production, volume of air needed for the drying of WPC80, mass of lactose crystals produced, volume of water removed in the evaporation during the lactose production, volume of air needed for the drying of lactose , yield of crystals produced with respect to the initial amount of lactose .
explain the ideal solution from viewpoint of thermodynamics together with the mathematical functions or the definitions of physical properties and demonstrate the experimental method to find ideal solution for binary
An ideal solution's thermodynamic properties can be calculated using the Gibbs energy of mixing and other thermodynamic concepts. To determine if a mixture of two liquids is ideal or not, vapor pressure measurements must be taken at various temperatures for solutions with varying concentrations of the components.
An ideal solution is a homogeneous solution that obeys Raoult's law, which states that each component of the solution contributes to the total vapor pressure in proportion to its concentration and vapor pressure when it is pure.
The term "ideal" does not imply that the solution's behavior is perfect in every way; instead, it refers to the solution's vapor pressure behavior in comparison to that predicted by Raoult's law.
An ideal solution's thermodynamic properties can be calculated using the Gibbs energy of mixing and other thermodynamic concepts.
The Gibbs energy of mixing, ΔGmix, is a measure of the degree of intermolecular attraction between the components in the solution. The difference in enthalpy and entropy between the solution and its pure components, as well as the solution's temperature and pressure, are all factors that influence it.
Experimental technique for determining an ideal solution for a binary liquid mixture :
To determine if a mixture of two liquids is ideal or not, vapor pressure measurements must be taken at various temperatures for solutions with varying concentrations of the components.
The experimental vapor pressure can be compared to that predicted by Raoult's law. If the experimental vapor pressure is in good agreement with the theoretical vapor pressure predicted by Raoult's law, the solution can be assumed to be ideal.
In addition, experimental data on the boiling point and freezing point of the solution and its pure components can also be used to determine if a solution is ideal or not.
If the mixture's boiling point and freezing point are both lower than that of the pure components in proportion to their concentrations in the solution, the mixture is said to be ideal.
Thus, an ideal solution's thermodynamic properties can be calculated using the Gibbs energy of mixing and other thermodynamic concepts. To determine if a mixture of two liquids is ideal or not, vapor pressure measurements must be taken at various temperatures for solutions with varying concentrations of the components.
To learn more about Gibb's energy :
https://brainly.com/question/9179942
#SPJ11
3. Derive Navier-stokes equation in Cylindrical coordinate system for a fluid flowing in a pipe. Enter your answer
These equations represent the Navier-Stokes equations in cylindrical coordinates for a fluid flowing in a pipe. They describe the conservation of mass and momentum in the fluid, taking into account the velocity components, pressure, density, viscosity, and gravitational effects.
The Navier-Stokes equation in cylindrical coordinate system for a fluid flowing in a pipe can be derived as follows:
Consider a fluid flow in a cylindrical coordinate system, where the radial distance from the axis of the pipe is denoted by r, the azimuthal angle is denoted by θ, and the axial distance along the pipe is denoted by z.
The continuity equation, which represents the conservation of mass, can be written in cylindrical coordinates as:
∂ρ/∂t + (1/r)∂(ρvₑ)/∂θ + ∂(ρv)/∂z = 0
where ρ is the fluid density, t is time, vₑ is the radial velocity component, and v is the axial velocity component.
The momentum equations, which represent the conservation of momentum, can be written in cylindrical coordinates as:
ρ(∂v/∂t + v∂v/∂z + (vₑ/r)∂v/∂θ) = -∂p/∂z + μ((1/r)∂/∂r(r∂vₑ/∂r) - vₑ/r² + (1/r²)∂²vₑ/∂θ²) + ρgₑₓₓ
ρ(∂vₑ/∂t + v∂vₑ/∂z + (vₑ/r)∂vₑ/∂θ) = -∂p/∂r - μ((1/r)∂/∂r(r∂v/∂r) - v/r² + (1/r²)∂²v/∂θ²) + ρgₑₓₑ
where p is the pressure, μ is the dynamic viscosity of the fluid, gₑₓₓ is the gravitational acceleration component in the axial direction, and gₑₓₑ is the gravitational acceleration component in the radial direction.
These equations represent the Navier-Stokes equations in cylindrical coordinates for a fluid flowing in a pipe. They describe the conservation of mass and momentum in the fluid, taking into account the velocity components, pressure, density, viscosity, and gravitational effects.
Please note that this derivation is a simplified representation of the Navier-Stokes equations in cylindrical coordinates for a fluid flow in a pipe. Additional terms or assumptions may be included based on specific conditions or considerations.
To know more about fluid , visit;
https://brainly.com/question/13256681
#SPJ11